Search Documents

By Ehsan Alavi, Brian Hagan, Colin LaVassar, Glen Frank, Derek Dugan, Rick Capka, Lisa Mori

"Tunnel face instability is one of the most common issues in EPB tunneling. The evaluation of an ideal face support pressure is a critical element in the design and construction phases of EPB tunneling. In this study, measured tunnel face pressures in three EPB tunneling projects (University Link U230 and U220 projects and the Northgate Link Extension N125 Project) for Sound Transit in Seattle, WA are compared with the calculated analytical methods. This comparison shows that the analytical methods generally overestimate the required tunnel face support. The best practice for managing the face pressure in EPB tunneling operation is discussed based on the experience gained through these projects. Furthermore, the algorithm that is developed for identifying ground loss in these projects is addressed. INTRODUCTION Earth pressure balanced tunneling relies on using muck within the chamber to support the face. Muck is pressurized by controlling the advance rate of the tunnel boring machine and the speed of the screw conveyor. Target face pressure is typically calculated by using the geotechnical assumptions in the geotechnical baseline report. The concept behind EPB tunneling is that the application of sufficient face support pressure will prevent tunnel face instability and the resultant over excavation. Tunnel face instabilities caused by a lack of sufficient face support can lead to ground loss and surface settlement (Anagnostou & Kovári 1996, Kirsch 2010). A certain support pressure must be achieved to counteract water and earth pressure with an adequate factor of safety. While the water pressure can be predicted accurately, the determination of the resultant earth pressure on the face is less precise. This becomes manifested in the relatively high partial safety factors on the earth pressure."

Jan 1, 2016

By Mark Springett

Microcomputers have rapidly evolved to the level at which they can perform almost all of the computational tasks required for exploration, evaluation and exploitation of mineral deposits. The present capabilities of microcomputers are reviewed by examining their use on typical projects from the initial capture of exploration data to the subsequent technical and financial evaluation by microcomputer. Emphasis is placed on the need for compatible software and on the importance of a consistent hardware acquisition policy.

Jan 1, 1987

By Davorin Kolic, Harald Wagner

Conventional ground support in accordance with latest state-of-the-art considers proper preparation of geotechnical investigation, structural design, observation during construction and fair risk sharing documents. Depending on the ground, there are different means and methods, reflecting different experiences. The paper is presenting ground support concepts, as mostly used in Europe during the past three decades. It discusses the use of anchors as well as the use of steel arches respectively combinations. It also discusses different applications of plain shotcrete, respectively fibre reinforced shotcrete. As excavation sequence is a major input to create the ground arch, the paper discusses also criteria to create closed ring conditions. Finally deformation criteria will be presented with case histories in order to control stability of the structure.

Jan 1, 2001

By Brendan Demich, Brendan Macdonald, Timothy J. Orr, Jonathan K. Hrica, CASSANDRA L. HOEBBEL, Jason Navoyski, Jennica L. Bellanca

Haul truck fatal accidents and injuries continue to be a significant concern for the mining industry. However, the availability of high-quality training materials continues to be limited. Near-miss incident accounts, if packaged well, could help fill this gap, because for every fatality, there are hundreds of reportable accidents and thousands of undocumented near misses. Researchers from the National Institute for Occupational Safety and Health (NIOSH) collected detailed accounts of 21 near-miss incidents in virtual interviews with mineworkers at surface mining operations across the country. From these interviews, researchers created four simulation videos using the Unity game engine. The simulation videos bring these events to life through first-person retelling and various visual perspectives of actual events. Each video exemplifies a critical safety message and a common haul truck hazard. This paper describes the process of taking narratives and turning them into impactful visual stories using graphic simulation. NIOSH plans to co-release these simulation videos with the Mine Safety and Health Administration (MSHA) to the mining industry to raise awareness and ultimately help reduce haul truck-related accidents and fatalities in mining.

Jun 1, 2023

By R. Venugopal, V. K. Saxena, Veerendra Singh

"Ore morphology plays a vital role during the milling and liberation of minerals. This study was carried out to understand the role of mineral crystallography and mineral interfaces on the milling and liberation processes. Data related to mineral crystallography, Vickers Hardness Number and beneficiation processes were collected from literature, and detailed statistical analysis was conducted to relate these parameters. Review of the crystallographic information of minerals present in ores indicates that molecular weight and cell parameters significantly affect milling and liberation characteristics. Mineral interfaces were classified into the three categories of coherent crystals, semi-coherent and incoherent crystals, and breakage behaviors were studied. The studied cases revealed that these material interfaces control the micropore properties that play a vital role in the initiation of intergranular and intercrystalline fractures which occur in siliceous manganese ores and dolomite as a result of thermal treatment. In contrast, banded hematite jasper and coal exhibited a much more complex fracture pattern due to their coherent interfaces and finer physical associations. This study explains the effect of the various types of interfaces on milling, and the approach can be helpful in developing a methodology to enhance mineral liberation with minimum energy consumption.IntroductionComminution is a vital unit operation in the mineralprocessing, cement-making, power-generation and pharmaceutical industries. Its importance in mineral beneficiation operations is increasing every year as a result of the growing need to exploit lower-grade ore bodies and process reject materials (Blazy et al., 1994; DOE, 2005). Low-grade ores require significant energy during grinding to liberate the valuable minerals, which are further separated from the gangues by various beneficiation methods. Various attempts have been made to enhance mineral liberation during grinding to minimize energy consumption. Most of these studies focused on the analyses of the compression mechanism, chemical additives, thermal treatment, microwave treatment and electric disintegration (Klimpel and Austin, 1982; Norgate and Weller, 1994; Bearman et al., 1997; Kumar et al., 2010; Wang et al., 2011; Singh et al., 2012). However, many of these efforts had limited success, and there is a need to see the problem from a fresh perspective."

Jan 1, 2015

By V. M. Torres

An empirical correlation to detennine laboratory mill grinding time has been developed. Grinding samples to 90 ± 5# below 147 micrometers was required for a flotation testwork at Companhia Vale do Rio Doce (CVRD) Research Center. The initial samples were all below 1 mm in size with different size distributions and work indices (Wi) ranging from 13 to 23 kWh/st. Grinding curves were determined for some initial samples. A correlation was developed between percent retained on 147 micrometers at a standard time and the time required to grind each sample to the required size. This correlation was then used to grind all samples, based on the preliminary grinding model. Finally, a statistical analysis with the size distribution of all samples was performed. The success of using the correlation was confirmed and an equation was determined using the data set.

Jan 1, 1996

By Samuel A. Rasmussen

Lead anodes are used in commercial copper electrowinning operations, yet there is no method to calculate anode life. To be discussed in this paper are operating characteristics of rolled plate (Pb,Sn,Ca) alloy anodes at Morenci's electrowinning tankhouse along with fundamental operating conditions and how the anode reacts to these conditions. These include anode maintenance, electrolyte temperature and viscosity, cobalt concentration, and manganese concentration. Also to be discussed are anode substrate characteristics under normal operating conditions and how the corrosion rate is affected by changes in operating conditions.

Jan 1, 1995

By Dale R. Ralston, Roy E. Williams, Gerry V. Winter, George L. Bloomsburg

Ground water inflow into a mine and the re¬sultant impact on district hydrology can be pre¬dicted on a site specific basis once the ground water flow systems at the site are sufficiently well under¬stood so that a valid conceptual model can be de¬veloped. Ground water flow systems are controlled by the hydrogeologic properties of the materials at the, site, including hydraulic continuity along flow paths, and boundary conditions. Preliminary delin¬eation of hydrostratigraphic units for conceptual models frequently can be based on surface water data; specifically, spring locations and the gain-loss reaches of streams. Quantitative predictions of mine water inflow and its impact on regional hydrology require col¬lection and analysis of numerous types of data. Hydraulic conductivity must be defined quantita¬tively both parallel and perpendicular to bedding as well as areally for each hydrostratigraphic unit. The characteristics of the Davis shale in case his¬tory number 2 illustrate this concept very well. The storage characteristics also must be determined for each hydrostratigraphic unit and the potential or hydrostatic head should be quantified vertically and areally for each unit. The potentiometric measure¬ments in the Bonneterre Formation as discussed in case history number 2 illustrate this point. The data collection and data analysis techniques constitute the weak link in the analysis of mine inflow and district impact. The technology for char¬acterizing a mine site in the field has lagged behind the technology for mathematical simulation; we at¬tribute this development to the fact that computer modeling is relatively inexpensive compared to field data collection and analysis. On-site tests provide the best means of quan¬tifying hydraulic conductivity parallel to bedding and the storage characteristics of the unit. Pump tests with multiple observation wells provide the best information from on site tests. Hydrogeologie boundaries can be located from such multiple well tests. Multiport piezometers provide a means for determining the vertical potential in a single borehole. Borehole geophysics can facilitate the def¬inition of hydrostratigraphic units. Vertical hy¬draulic conductivity is difficult but not impossible to quantify with existing field test methods; labo¬ratory tests of cores fail to give a value represent¬ative of the field situation. The storage characteristics of a confined (artesian) hydro¬stratigraphic unit can be difficult to quantify when pumping changes the confined unit to an uncon¬fined (water table) case after depressurization and dewatering. Transmissivity and storage coefficient can be approximated to some extent for given field con¬ditions by computer modeling if enough is known about hydrogeologic boundaries. Modeling can be used in a trial-and-error approach to match transmissivity and storage coefficients to existing water level data corresponding to estimated discharge rates. A solution can also be obtained using a tech¬nique referred to as the inverse method. Unfortu¬nately, such a solution is seldom unique. Fracture flow models exist but practicality usu¬ally necessitates reversion to a basic Darcy flow model. Data requirements for fracture flow models could be difficult to fulfill where fracture aperture, spacing, orientation, and length are required. Ob¬taining such data at depth prior to mining would be impossible for any mine simulation in fractured media. We are of the opinion that most fractured media simulations can be accomplished using con¬ventional Darcy flow models by viewing the field problem on a macroscopic scale. The real challenge is to delineate hydrostratigraphic units properly in the field. The question of whether a broken-up fault zone is an aquifer or a barrier boundary is seldom simple. The fractures usually can be treated as an equivalent porous medium in either case. Only a few techniques exist for predicting un¬derground mine water inflow. These techniques fre¬quently are designed to evaluate shaft or tunnel inflow under steady-state head conditions in a sin¬gle layer rather than in multiple hydrostratigraphic units. Few computer programs exist that have the

Jan 1, 1986

By J. Mastoris

The growing environmental awareness and the need for providing social service to the community, urge the primary sector companies (such as mining) to find new solutions, by adjusting their operations with the special, local conditions and meeting everyday problems in practical ways. We hereby present a real case of re-design of an open pit, closed-bench type industrial minerals (clay) excavation, for the purpose of rehabilitation and utilisation as a water reservoir. The potential use of rainfall water was studied on the basis of covering the irrigation needs and improving the living standard of the neighbouring farmers and also as a project or recreational development of the area by shaping a wetland. The experience from the project progress and the reservoir use has been positive to date and the reclamation plan seems to have the acceptance of the local community.

Jan 1, 2002

By M. Abdel-latif, R. W. Bartlett, P. R. Taylor

A cyclone reactor system for the partial reduction and melting of taconite concentrate fines was designed and operated. A nontransferred arc plasma torch was employed as a heat source. Taconite fines, carbon monoxide and carbon dioxide were fed axially into the reactor, while the plasma gas was introduced tangentially into the cyclone. The average reactor temperature was maintained above 1673 OK (1400°C), and reduction experiments were performed under various conditions. The influence of the following parameters on the reduction of taconite was investigated: carbonmonoxide to carbon dioxide inlet feed ratio, carbon monoxide inlet partial pres- sure and average reactor temperature. The interaction of the graphite lining with carbon dioxide and taconite were also studied.

Jan 1, 1995

By W. M. Cross

The hydrophobic character of sapphire surfaces in SDS solutions was examined with respect to the aggregative nature of the adsorbed surfactant phase. It was found that, at equilibrium, sapphire surfaces having adsorbed SDS bi-layers exhibited no contact angle. Conversely, when the adsorbed SDS was found to be mi-cellar in nature, sapphire surfaces developed significant hydrophobic character. The surface states as detected by Fr -IRIIRS conformational analysis were found to be reversible with temperature. The variation in adsorption density with temperature was studied by in situ Fr-IRIIRS. The isosteric heat of adsorption was calculated to be -1.6 kcal/mole. Although the adsorbed SDS was found to undergo a reversible phase change between 25 and 32°C, similar to SDS in solution, the extent of adsorption was not reversible with temperature.

Jan 1, 1993

By E. H. Kurt

INTRODUCTION The simplest way to drill a hole into rock is to strike a steel chisel or drill bit with a hammer. Early miners used this elementary hand technique so successfully in "single jacking" and "double jacking" that the first mechanical rock-drill designers sought to duplicate it. However, in the early developments, the designers were forced to retreat to a construction known as the "piston drill," wherein the entire drilling element is tied to the piston and reciprocates with it. It took nearly 50 years to devise a method of divorcing the two elements and to achieve the original hammer principle used in hand drilling. The Mont Cenis tunnel, drilled through the French Alps in 1861, usually is considered the birthplace of the mechanical rock drill. The Hoosac tunnel in Massa¬chusetts was drilled at about the same time, and the success of these two ventures paved the way for innova¬tions that produced the Burleigh, Ingersoll, Sergeant, and Waugh piston drills between 1870 and the turn of the century. In 1897, George Leyner of Colorado introduced what has been considered the most significant development in rock-drill history. He devised the hollow drill steel for water flushing; when combined with his free-piston hammer drill, this became the first lightweight and dust¬free underground machine. In addition, Leyner's drills introduced improvements such as automatic rifle-bar rotation of the drill steel and chuck, automatic lubrica¬tion, and an enclosed throttle control. During the 1920s and 1930s, automatic feeds, centralizers, sliding cones, and the automatic water back head were developed, laying the groundwork for all pneumatic underground drills currently in use. Since these pioneering efforts, rock-drill development has been concerned primarily with refining the designs and improving the metallurgy to make faster, lighter, and more dependable machines. Fig. 1 illustrates the progress in drilling speed during the first 125 years of rock-drill development; that progress is a credit to the persistence and inventiveness of the designers in the rock-drilling industry. ROCK-DRILL CLASSIFICATIONS To meet the variety of conditions encountered in rock drilling, several distinct types of drills have been de¬veloped. In general, rock drills may be classified as either hand-held or mounted, with the hand-held ma¬chines including the jackhammer or sinker, the jackdrill or jackleg, and the stoper. The mounted drills are com¬monly known as "drifters." Table 1 shows that each type of drill is available in several sizes from different manufacturers. Fig. 2 illustrates a typical rock drill, showing the principal components. The jackhammer or sinker, shown in Fig. 3, is used primarily for general mine utility work such as drilling anchor holes (short vertical holes to bolt or anchor machinery), pin holes (short, usually horizontal holes to fasten sheaves, etc. to side walls), popholes (for blasting large boulders), and similar applications. They also are used for shaft sinking. Jackhammers are classified ac¬cording to weight, and they range from 7 to 30 kg (15 to 65 lb). The rock drill originally known as a jackleg was made by clamping a pneumatic cylinder or leg to a jack¬hammer, both to support the weight of the machine and to feed the tool forward in horizontal or uphole work. The more modern jackdrill refined this concept to make the hinged pivot for the leg integral with the drill cylinder and to group all drill and leg controls in the drill back head for convenience. Fig. 4 illustrates a typical jackdrill. Jackdrills are classified according to cylinder bore size, ranging from 60 to 83 mm (2.375 to 3.25 in.). Because of their light weight and versatility, jack drills are very effective in small drifts, small tunnel head¬ings, and stoping. The larger machines are applied to hardrock formations and in applications where drilling speed is a primary consideration. In soft formations or

Jan 1, 1982

By James McKelvey, Larry Drolet, Jason Swartz

INTRODUCTION When divers discovered that sections of a tunnel housing the pipeline that conveys wastewater from the Charleston Peninsula to the Plum Island Wastewater Treatment Facility had caved in, the Charleston Commissioners of Public Works(CPW) moved quickly to determine a long term solution for the city’s collection system, immediately focusing on the Ashley River sewer tunnel along the western boundary of the peninsula. Working with the Charleston community, as well as federal, state, and local officials, CPW developed a fast track yet long life design that can be used as a model for underground construction of tunnels in urban areas. The paper that follows summarizes key aspects of the Ashley River sewer tunnel project. HISTORICAL CHARLESTON Charleston, South Carolina is a culturally significant and historic city that was originally settled in 1670. There are over 100 buildings on the National Register of Historic Places within the Charleston area. Additionally, the first shots of the American Civil War were fired at Fort Sumter in the Charleston Harbor in 1861. As one can imagine, tourism generates significant business for the area with over 1.5 million people visiting Charleston each year. No project, especially one that requires digging, is done within the old city on the Charleston peninsula without careful planning. Many precautions are necessary to prevent damage or disruption to the historical properties. The Ashley River sewer tunnel project is exclusively in the old city. A lot of work was done during the design phase to minimize the impact to historical properties. Some of this work included: an archeological study (where pre-digs were monitored at all shaft sites by an archeologist); a building/structure assessment study (where structures near a shaft site were completely surveyed and cataloged); and an environmental study.

Jan 1, 2005

When science and the human spirit come together amazing things can happen. This was perhaps never more evident than through the events that unfolded during August and October in a remote desert in northern Chile. On Aug. 5, the main shaft of the San José copper and gold mine near Copiapó in Chile?s Atacama Region collapsed, leaving 33 miners trapped more than 624 m (2,000 ft) beneath the earth?s surface.

Jan 1, 2010

By Robert B. Gordon

The Reverse Curve Tunnel Project was located in Glenwood Canyon, Colorado approximately twelve (12) miles east of Glenwood Springs. The Project was one of many being constructed over a period of time by the State of Colorado, Department of Highways to improve Interstate 70 to four lanes as it travels thru the environmentally sensitive Glenwood Canyon. The Project consisted of excavating and concreting a tunnel approximately five hundred fifty (550) feet long, forty two (42) feet wide, and thirty two (32) feet high. The designer was Parsons, Brinkerhoff, Quade and Douglas, with geotechnical consultation provided by Woodward Clyde. CONSTRUCTION CHALLENGES There were several significant construction challenges presented primarily by the physical location of the Project. In this study each problem will be discussed, as well as how it was overcome by construction methods and/or design requirements. Portal Excavation - One of the most difficult areas of work on the Project consisted of excavation and stabilizing the East and West Portal rock prior to tunnel excavation. The Reverse Curve Tunnel passes through a sheer walled cliff face which is approximately two hundred fifty (250) feet high. Geologically the cliff consists of primarily sedimentary deposits with open, weathered joints and vertical faulting. Before the tunnel excavation could begin, a narrow sliver cut had to be excavated and rock

Jan 1, 1989

By Mining Engineering

The 43rd Annual American Mining Hall of Fame Awards Banquet and Fundraiser, sponsored by the Mining and Minerals Education Foundation (MMEF), will be held Dec. 6 in Tucson, AZ. Each year, the MMEF honors a slate of individuals and companies who have made notable contributions to the advancement of the mining industry. This year’s distinguished nominees are: Kathleen L. Quirk, president and chief executive officer and a member of the board of directors of Freeport-McMoRan Inc. is the 2025 Hall of Fame Inductee. Quirk joined Freeport in 1989 and had responsibility for a broad range of corporate functions, including tax, investor relations, corporate development and treasury before being named chief financial officer in 2003. She was named president of Freeport in 2021 and became a member of the board of directors in 2023. As a senior member of the company’s executive team for more than 20 years, she has been instrumental in Freeport’s strategic planning and execution of company goals. During that period, Quirk was named Best CFO in Metals and Mining by Institutional Investor Research magazine on numerous occasions. She holds a bachelor of science in accounting from Louisiana State University.

Aug 1, 2025

By G. A. Gunderson

Since our time is very limited, I would like to relate to you as best as I can a few important areas that I think may be helpful. 1.) The Real Difference between Dense Phase and Dilute Phase Pneumatic Conveying: Within the many variations of so called Dense Phase conveying, it is often difficult to determine to what degree a system is Dense Phase or if, in fact, it is a Dense Phase system at all. A system that appears and is generally known to be Dense Phase can under certain operating conditions perform as a Dilute Phase system. If, for instance, a high pressure system, which is generally a Dense Phase system, operates at 60 PSIG, say 4 atmospheres, utilizes enough air volume, the conveying velocity will easily exceed the normal design velocity of a typical Dilute Phase system. Now, on the other hand, a low pressure system which we will term a Dilute Phase system, operating at 15 PSIG; say 1 atmosphere, can convey a given product at well below the saltation velocity, like a Dense Phase system.

Jan 1, 1977

By Robert M. Cox

The principal factor that must be determined for the effective design of a coal mine roof bolt support system is the maximum stable tension that can be developed with a given bolt assembly in a particular roof rock. There are four basic types of roof bolt anchorage techniques available: (I) the splitwedge; (2) mechanical expansion units; (3) resin point anchors or grouted expansion units; and (4) the cone shell which is placed in a reamed hole. A study of this problem has been made which includes theoretical analyses, laboratory experiments and field tests. A static free-body analysis of each of the anchorage techniques has provided formulas for predicting the anchorage capacity for a particular rock from the results of standard pull tests. The formulas also provide an insight into the anchorage mechanism of technique and allow for a comparative evaluation of the methods for design purposes. The theoretical analyses also indicate clearly the pertinent variables affecting the anchorage mechanism of each method.

Jan 1, 1977

By Georges E. Vaillant

Air pollution control in primary aluminum smelter . Various processes are known for air pollution in electrolysis plants. Mainly two systems have to be taken into consideration: -Treatment of concentrated gases collected directly from hooded pots. This is normally achieved by either dry or wet process. This is not the object of this paper as these processes have been already described. -Treatment of low concentrated fumes. A certain amount of gaseous and solid fluoride (35 % of total fluor pollution) goes out of the hooded pot. Gases commonly called secondary fumes are generally treated by wet process. The object of 'this paper is to describe two plants with specific treatment for secondary fumes. 1/ A plant in operation in Vlissingen (Netherlands) for PECHINEY. 2/ Presentation of tests carried out by a specialized Company. The results of such tests have been used for the design of the scrubbers presently under construction for ALUMINIO ESPANOL San Ciprian (Spain).

Jan 1, 1978

By Wang Yingmin, Xu Zhuyun

There are 3 steps in the process of forming a mine ventilation system, (1) selecting a reasonable ventilation pattern (included pit shaft arrangement); (2) optimizing of the ventilation network and (3) computing and outputting the flow splitting results of the network with the optimal ventilating equipments selected. In the past, the first step was relied on artificial decision-making. In order to design a common ventilation system, some ventilation experts were needed to participate or do some examinations. Even so, the design made was reasonable only for those experts. If there is a mistake in the first step, then even the followed 2 steps are best done, the losses are very difficult to retrieve. So that, the first step is very important. The development of expert systems provided an efficient means and tool for all engineering fields. This paper presents an expert system of selecting mine ventilation pattern and pit shaft arrangement. After testing many times, it is shown that the system can perform the first step of designing a mine ventilation system, and can help the experts doing their study works more efficiently.

Jan 1, 1991