Search Documents

By K. C. Ko, M. D. Bunnell

The studied coal mi1e is an underground coal mine located in the northern Wasatch Plateau of central Utah (Figure 1) . Since operation began in 1981, in situ stress conditions have been encountered which differ from the assumed conditions utilized during early mine design efforts. Geologic structures also varied somewhat from those projected during initial geologic interpretations of the area. The encountered geologic conditions combined with the unusual stress conditions prompted a combined study of in situ stress and stress-related geologic structures. The study was conducted in two phases, with phase 1 consisting of detailed underground mapping and analysis of stress-related geologic structures to determine stress orientations from which they originated; and phase 2, consisting of over- coring two sites within the mine to determine present in situ stress orientations and magnitudes. GEOLOGIC ANALYSIS Three types of geologic structures have been encountered in the mine that act as indicators of stress orientations of the geologic past. Two of these structures, faulting, and igneous dikes, are directly measurable in the mine. A third type of structure, photolineation, was detected through remote sensing methods and shoe god correlation to roof conditions in certain areas of the mine. Faults Two major orientations of faulting have been encountered in the studied coal mine, including a system of N 80 W striking normal faults and a system of N 55 to 70 W striking oblique-slip faults. Only data collected from the oblique-slip faults were used for this study due to the fact that these faults offset the N 80 W faults wherever the two systems intersect, indicating that the N 55 to 70 W system was created by a more recent stress field. Figure 2 shows locations within the mine where data were collected from seven locations along oblique-slip faults. Data collection consisted of measurement of fault plane strike and dip, fault slickenside trend and plunge, and slip direction. The data are tabulated in Table 1. The fault data were then plotted on stereo nets to determine the stress orientations present at the td of faulting (Figure 3). The determined stress orientations are 32~0 included in Table 1. The stereo net plots show average principal stress orientations of: 1) [ ] plunge 1 degree. These data suggest that the N 55 to 70 W oblique-slip faults were produced by a nearly

Jan 1, 1986

By E. Fahrenkrog

An intelligent supervisor developed using expert system tools and applied to a crushing plant is presented in this paper. The structure of this supervisor, based on a model of a human operator, consists of a Knowledge base containing a qualitative model of the process, and a Rules base with the heuristic logic used by an operator when supervising a plant. The simulation results obtained show the potential of this type of systems to supervise the automatic operation of a plant.

Jan 1, 1989

By Y. Luo

In designing and operating underground room-and-pillar coal mines, it is always difficult to achieve a good balance between preventing surface subsidence and achieving high recovery ratio. In this paper, a design methodology applying the pressure arch theory is proposed, and the principles and mathematical models involved are detailed. A computer program was developed to carry out the design optimization process and was applied to the examination of a documented case in which a massive cascading pillar failure had occurred over a large area in a shallow coal mine. The results indicate that the proposed design method can be applied to prevent subsidence while achieving reasonably high recovery ratio for roomand- pillar mining operations.

Jan 1, 2014

By O. Ofor

Coal fines of less than 0.5 mm particle size, discarded as too fine for gravity separation, were subjected to flotation tests at varying pH and temperatures using modified dosages of kerosene as oil phase and methylisobutylketone (MIBK) as frother. Optimal coal recovery of over 74% was obtained using 200 kg kerosene and 4 kg MIBK per ton of coal fines at a pH of 9.7 and an ambient temperature of 26° C. The coal concentrate obtained under these optimal recovery conditions assayed 9.10% ash, 0.35% sulfur and 0.011% phosphorus, representing reductions in the ash, sulfur and phosphorus contents of approximately 75%, 43% and 8.3%, respectively. Its gross calorific value was 32.9 MJ/kg, its percentage of volatile matter measured 30.6 and the fixed carbon content was 66.3% (d.a.f). Caking tests showed the optimal concentrate has a standard welling number of 1 and is a Gray-King coke type C. These results show that the optimal flotation product could be utilized for such industrial purposes as steam raising or for processing in gasworks, but it would be unsuitable for metallurgical coke production.

Jan 1, 1993

By H. R. Weischedel

The art of wire rope inspection has advanced rapidly over the past decade. Present electromagnetic (EM) wire rope inspection instruments provide an important and often vital element of wire rope inspection. Some instruments are easy to operate and offer simple and clear data interpretation. Simultaneously, wire rope inspection and retirement standards are becoming simpler and more lucid. Future guidelines will he easy for inspectors to apply and for rope operators to fulfill. The thrust of evolving regulations is clearly toward periodic EM inspections supported by visual inspections. These development sallow even moderately skilled personnel to perform EM inspections of wire ropes. Therefore, it is now possible and cost effective for wire rope users to have EM and visual inspections performed by in-house personnel. In-house EM inspections have many advantages and offer an excellent return on the initial investment. Since EM inspections can detect rope deterioration in its beginning stage, wire rope users recognize that they are an effective preventive maintenance tool. For instance, the early detection of wear or corrosion allows immediate corrective action. This can easily double, or even triple or quadruple, the service life of a rope.

Jan 1, 1991

By M. R. Peterson, C. R. Ferguson, T. H. Jeffers

The ability of microorganisms such as yeast, bacteria, and various aquatic flora to sorb metals from dilute aqueous solutions is well documented. Although microorganisms have significant potential in decontaminating waste waters, techniques and equipment suitable for bioassisted decontamination are limited. The Bureau of Mines has investigated the use of microorganisms immobilized in porous polysulfone beads for extracting toxic and heavy metals from dilute waste streams. The minus 8- plus 12-mesh beads were fabricated from high-density poly- sulfone dissolved in dimethylformamide (DMF). Dried, thermally killed yeast, algae, duckweed, xanthan gum, and alginates were blended into the polysulfone-DMF, and spherical beads were formed by injecting the mixture into water. Microscopic analysis revealed microorganisms immobilized within the bead pores. The beads had excellent handling characteristics and were tested in stirred reactors, fixed bed columns, and fluidized bed columns for their ability to remove metal contaminants from several waste waters. The effluents resulting from these waste waters met or exceeded the National Drinking Water Standards for cadmium, copper, manganese, and zinc. Other heavy metal contaminants readily sorbed by the beads included arsenic and mercury. Elution of metal values from the beads was accomplished using dilute nitric acid or sodium carbonate.

Jan 1, 1989

By D. E. L. Zapata, O. J. R. Baena

"INTRODUCTION Mining is a fundamental part of the historical and economic development of a country. In Colombia, this is reflected from pre-Columbian jewelery, to being now one of the first exporters of coal worldwide, in 2017, the Colombian mining sector contributed approximately 6% of GDP (Ministerio de Minas y Energía, 2017). Coal, nickel, gold, platinum, emeralds, limestone, salt, phosphate rock, clays, siliceous sands and to a lesser extent copper, manganese, magnesite, barite, gypsum and various types of ornamental rocks, among others are produced (UPME, 2016). The contributions of mining activity in the economic dimension is more measurable, on the contrary in other dimensions, as the social and environmental, for this, every day there are new proposals and tools oriented to strengthen how to evaluate the contributions in terms of the sustainability and responsibility, with the aim of quantifying, concreting and non-utopian, to improve the life quality of a community and not only to comply with reporting and gaining prestige. Colombia has a generalized increase in the mining sector where the levels of informality and illegality are evident only 10% of mining activity is legal (UPME, 2014), also, the mining sector is accused of human rights violations, high levels of inequality, poverty and the affectation of ecosystems due to bad environmental management, among other situations (ACNUDH Colombia, 2015). This problem has generated rejection to the realization of the mining activity in many places of Colombia. At this point, it is important to clarify this problem is more complex, different actors are involved in this conflict, but it is an evidence that is needed a sustainability model for specific realities such as the Colombian mining. This situation in the current mining activity, is similar to the chemical industry situation three decades ago, because of an extensive problem in relation to repeated work accidents, natural disasters and indications as a highly polluting and unsustainable industry, with the aim of improving, not only this public perception, but also in the way of carrying out the business activity. Thus, in 1985, the Canadian Chemical Producers Association released the Responsible Care Program (RCP) (ICCA, 2015). Being aware that companies were responsible for the affected lives in some way by the operation and needed to improve workers safety, environmental protection and most importantly how legal persons should comply with the law, but go beyond this. RCP is most recognized sustainability initiative in the chemical sector, companies associated are recognized for having high quality standards, continuous improvement, visibility, corporate ethics, environmental and social management (ACC, 2015). In addition, to meeting the objectives is set out the creation of a model that increasing reputational sector levels. This initiative is considered to be a worldwide successful case of reporting corporate responsibility indicators and contributions to sustainability from the industry sector to local development (BASF Group, 2016)."

Jan 1, 2018

By Vladimir Nikolić, Alex Doll

The Bond ball mill grindability test is one of the most common metrics used in the mining industry for ore hardness measurements. The test is an important part of the Bond work index methodology for designing and measuring the efficiency of mineral grinding circuits. In spite of being called “Bond’s Law,” the work index equations are not a law of nature; but rather an empirically measured regression of a large data set collected by the Allis- Chalmers corporation in the period between 1930 and 1952. As a regression, it is valid within a specific “calibration space,” and great care is required when deviating the test procedures or observing results that are outside of that calibration space. This paper is a collected summary of other works by the Authors that describe feed sizes, product sizes, quality control checks, and other information about interpreting the test and using its results. Examples of adjustments that are sometimes required when using the test are: changing the test product (P80), and coping with a feed that is too fine to apply the “proper” feed preparation steps (such as is sometimes observed from HPGR or SAGDesign product testing). Related metrics, like the Morrell Mib value and Levin B value will be discussed, along with recommendations for their use on design projects. The intended audience is any user of laboratory work index test data.

Feb 1, 2024

By Richard Komarek

When limestone (Ca03) is calcined in rotary kilns to produce quicklime (CaO), it is not unusual for 10% to 20% of the stone to abrade and emerge from the kiln as quicklime fines (-6.3 mm or -0.25 in.). While there are various industrial processes that can use fines, handling and shipping is tricky and dangerous. Due to the highly caustic nature of quicklime, airborne dust easily bums eyes and skin. On the other hand, money has already been invested in mining (or buying) the raw material and in the equipment and energy needed for calcining. Discarding the fines will not only waste that investment, but add even more cost in transportation and possibly dumping charges. So the question becomes, how can fines best be turned into a revenue-generating asset? Some plants convert leftover quick-lime fines into calcium hydroxide - Ca(OH)2, also known as hydrated or water-slaked lime - for sale into agricultural applications. For farm uses, hydrated lime fines are preferred over quicklime because they are easier to handle. And they are favored over raw limestone fines for their higher concentration of calcium and greater solubil¬ity. From the producer's viewpoint, quicklime fines are ideal for this use because they go through hydration faster than the larger chunks of quicklime. Those larger chunks, or "pebble lime," are more readily salable and more easily handled, for such uses as steel, copper, aluminum and magnesium production, water waste treatment, chemical, paper, glassmaking and flue gas desulfurization in coal- fired boilers.

Jan 1, 1993

By B. R. T. Simoneit

The formation of petroleum is normally thought of as a geologically lengthy process, involving the accumulation of organic matter, its gradual burial, diagenetic breakdown via geochemical reactions, maturation, heating within a 75-150'C "oil window" induced by normal geothermal gradients in the subsiding basin, and slow product migration into structural traps (Tissot and Welte, 1984, Hunt, 1979). The entire process can take millions of years and, indeed, most oil reservoirs probably formed in this manner. How-ever, today in sedimented, submarine rift basins (Fig. 1), Cl to >C40 hydrocarbons with the chemical and physical properties of crude oil are forming in demonstrably much shorter time by rapid thermal maturation of immature organic matter in hydrothermal regimes that are unusually high for sedimentary basins (Brault and Simoneit, 1988a, b; Didyk and Simoneit, 1988; Kawka and Simoneit, 1987; Peter et al., 1988; Simoneit, 1983; 1984; 1985a,b; 1988; Simoneit et al., 1984; 1987; 1988).

Jan 1, 1989

By Alireza Ayoubian, Richard Finno

The network of freight tunnels in Chicago consists of about 62 miles of horseshoeshaped tunnels constructed typically less than 50 feet below ground surface. These tunnels serve as repositories of much infrastructure and should remain serviceable. The tunnels are often impacted by adjacent excavations and the question arises as to the existing state of stress in the final liner. This paper discusses construction of these tunnels and presents the results of finite element analyses which were used to obtain ranges for axial forces and bending moments that have developed in the final liner of the freight tunnels since their construction.

Jun 13, 2023

By Stanislaw Siewierski

One of the major problems in the exploitation of deep copper ore deposits in the Legnicko-Glogowski Copper Field is ground control and, in particular, roof control of the headings. The depth of copper deposits ranges from 600 to 1200 m. The parameters of ore-bearing rocks and the surrounding rocks show considerable variance of strength properties along the mining thickness (Fig. 1). The roof of the openings exploitation headings consists of dolomite-calciferous rocks. The roof strata consist of layers, the thickness of which vary from several centimeters to 0.6 m (sometimes to 1.0 m). These strata differ in strength and are characterized by igneous and sedimentary discontinuities. On the basis of studies in structure, properties and geological mining conditions of the roof strata in Polish copper mines, the method of roof classification has been developed. (1) This method uses the stability index "L" of the roof, calculated from [ ] The value of "t" ranges from 0, l to 0,8. Based on the value of "L", four classes of the roof (Table 1) corresponding to different degrees of fall hazard have been developed. The mining of copper ore deposit is carried out by a single lift room-and-pillar mining system or a two-stage room-and-pillar system with roof caving. (3, 4). The single lift room-and-pillar mining system is most often used. It consists in working of the deposit of 2.5 to 4.5 m mining thickness, 150-350 m long mining line, consisting of parallel room faces 6 m wide with pillars 5.7 or 16 m wide. As the mining line advances, cross-cuts joining individual rooms are made, thus forming support pillars 3x5, 7x7, 5x16, and 7x16 m (Fig. 2). The two-stage system (Fig. 3) mines the deposit with rooms 6 m wide into blocks 25 x 35 x 25 x 45 m. During the second step these pillars are worked with rooms and cross-cuts into pillars about 3 x 4 to 4 x 5 m (retreat mining). The pillars are crushed just before the fall of the roof. The maximum opening of workings in the two-step system is about 10 m, i.e. one belt entry and one row of bearing pillars. In single lift room-and-pillar systems it is about 35 m., i.e. three belt entries and three rows of bearing pillars. The support of the headings consists of expansion bolts 1.6-1.8 m installed in a bolting pattern 1.1 x 1.5 m. In both systems the fall step is about 10 m, i.e. the width of a belt and a bearing pillar. The Indications of Rock Mass Pressure Individual Dog Heading Individual dog headings are set wide apart from each other in the unmined ore deposit area where there is no interaction of headings. The indication of rock mass pressure are, in such cases, limited to the deformations and damage of side walls. Radiometric studies of rock mass loosening showed that the maximum range of lifts in side-walls immediately after web was 2 m (4,5). In the course of time the cracked side rocks fall off, thus widening the heading. The morphology of side-walls is influenced by the location of the heading in relation to clump layer/tarry. This layer is characterized by a weak strength and "lubricating" properties. The location of the heading in

Jan 1, 1982

The price of copper has gone into the tank. So has gold. Environmental regulations are more restrictive. Global warming has world leaders and environmental groups seeking international regulations to keep the planet from heating up - mostly by restricting the use of fossil fuels. And the US Secretary of the Interior wants to make it more costly -prohibitively so for smaller companies - to mine hard rock metals in the United States. By rights, miners should be carrying around a pessimistic attitude about their industry. But miners are an optimistic lot, always believing that things will improve. That optimism was in evidence in Tucson, AZ in early December, when about 620 miners met at the Double- tree Hotel for the Annual Meeting of the Arizona Conference, put on by SME. Attendees listened as a United States congressman commented on the recent tax cut bill, mining regulations and the continuing need for the mining industry to improve its image in the eyes of the general public. Session speakers discussed how improved technology has made their processing operations at Sierrita and Morenci more efficient and cost-effective.

Jan 1, 1998

By B. R. Addison

In the Spring of 1991, Georgia Marble Company of Arizona (GMCOA), acquired the Andrada Marble Company located near Vail, Arizona, approximately 32 km southeast of Tucson. The Georgia Marble Company operation consists of an open pit quarry and a recently constructed, state of the art calcium carbonate milling and processing facility. The open pit quarry exposes white, crystalline, CaCO3, Escabrosa limestone that meets our customer criteria for Consumer and Industrial Filler applications. The Georgia Marble Company Arizona Division facility is designed and engineered to produce a wide range of milled calcium carbonate that includes finely ground and coarse screened products.

Jan 1, 1994

By Michael Michaylov

INTRODUCTUCTICN The coal seams at Bobov dol basin are highly prone to spontaneous combustion in Bulgaria. The risks of endogenous fires (SPONCOM) exist mainly in gob area. During the last 15 years three different technologies for preventing and fighting SPONCOM have been applied in underground mines of this basin: pulp from hard material and water, foam and inerting with nitrogen. On the basis of experimental application of these technologies as well as theoretical and experimental research a new technology - Foam Pulp Technology (FPT) was worked out. It is very effective in difficult to reach places in a gob. BACKGROUND AND THE NEED OF FPT Application of the three methods mentioned above showed advantages as well as some disadvantages, allowing determination of their effective application scope depending on geological and working conditions. Their advantages can be summarized as follows: - Foaming: high viscosity at low density, which allows forming a thick layer; good surfactant wetting properties; excellent effective cooling during evaporation in high temperature zones. - Pulping with mixture of solid particles (e.g., fly ash) and water from surface installation: easy to apply in a mine; low operational and energy costs due to gravity transport from the surface to the gob: good ecological results because the waste material is returned back underground. - Inerting with nitrogen: volumetric action which doesn't restrict the thickness of treated coal pile; easy to apply in a mine; controllable nitrogen delivery depending on fire hazard conditions. Main disadvantages of the same three methods are: - Foaming: rapid disintegration due to intrusion into heterogeneous and porous media and high costs due to the need of frequent large volume foam flows (short foam's life); - Pulping: inapplicable for coal piles with high thickness which is of great importance in the cases of seams with ununiform hypsometry (rapid and frequent changes in a seam configuration) and/or great volumes of coal or ore piles particularly heated to a high temperature; strong dependence on gob floor declination; water draining of the working face area which impedes the movement of supports and chain conveyor's. - Inerting: relatively high costs hardly depending on the rate of face advance (fig.1) in comparison with the other methods; it is difficult to ensure sufficient oxygen at the exit end of the face. This problem is crucial in faces with a high level of methane emissions; accelerating of the oxidation and spontaneous heating of the pile after turning off the nitrogen supply. Inerting should be applied again at higher capacity of nitrogen supply (fig.2) and what is more important, it shouldn't be

Jan 1, 1995

The minerals industry consumes billions of dollars in raw materials, equipment, tools, services and chemicals. The industry, though, has turned overmuch of the research and development (R&D) for these products to manufacturers and suppliers. Now the industry and its suppliers must decide how much R&D the mining industry should be responsible for and what role the suppliers should play. Promoting R&D As a result of the current environment in the mining and minerals industry, there has been a substantial decrease in R&D. Depressed prices, stagnant growth, cost cutting and rationalization are evident.

Jan 1, 2000

By D. L. Kuck

Water ice pillars far underground mine roof support can be frozen and/or maintained and/or melted on demand. The system to do this consists of a refrigeration brine chiller, brine circulation system and disposable plastic containers. Fusion expansion, resilience to dynamic loads, plastic deformation under stress, and non-contamination of coal or ore are unique properties of ice. Lower labor and material costs are economic advantages of ice far mine structural support. Ice brattices can become ice pillars on retreat. For safety, ice pillars can be placed (by remote control, if necessary) in hazardous sites without human entry.

Jan 1, 1988

By Agne Rustan

Most of the mines in Sweden are metal ore mines in hard rock and none of these mines are classed gassy because there is no methane emission. The risk of methane explosions in Swedish mines is therefore very small. Since the 1960?s, in Swedish mines, there has been a change from electric and pneumatic loaders and transport machines to diesel. Today in almost all Swedish underground mines diesels are used. One of the most common complaint from the underground mine- workers is the exhaust gases from the diesel-vehicles. This is a strong motive for attempts to assure a more comfortable environment. Another motive for a better efficiency of ventilation under ground is the increasing cost of energy for fans and for heating the air during winter. For the largest mine in Sweden, the Kiirunavaara Mine, 36% of the energy for ventilation is used for preheating the air during the seven months when the temperature is below zero. The air quantities used for ventilation are large. In table 1 a comparison of the ratio between yearly produced ore and waste rock and installed fresh 'air capacity is shown. [ ]

Jan 1, 1980

By Ibrahim S. Balbaa, J. Terry Strack, James G. Hopkins

A microwave system for continuously reactivating carbon, used in gold processing, has been demonstrated at a gold mine in Ontario, Canada. The pilot unit produced reactivated carbon at a rate of 12 kg/h. Comparisons with the mine's existing reacti­vation kiln indicate that microwave reactivation technology has several clear advantages over conventional regeneration kilns. Upon completion of the original study, the microwave reacti­vation technology was further developed. An advanced rotary type microwave system that can be scaled up to reactivate car­bon at a rate of 120 kg/hr was designed and smaller pilot-scale equipment was commissioned and tested. Under an agreement with OHT, Harper International Corporation will manufacture, supply, and market the new technology. In addition to carbon reactivation, the rotary microwave system can be used in many other heating applications such as ore treatment, ceramic pro­cessing, and cleaning of minerals.

Jan 1, 1998

By William E. Foreman

The results of the electrokinetic study of the activation of quartz by divalent cations showed that the charge reversal was related to the point at which the cation hydrolyzed. The reversal was not due to the presence of solid hydroxide at the surface of the quartz but due to the charged ions in the solutions. The charge reversal for beryllium at a log molar concentration of 1x10-4 was observed at pH 5 and 9. The quartz was positively charged between a pH reading of 5 to 10. Magnesium at the same log molar concentration did not show a charge reversal from pH 2 to 12. The probable cause of the charge reversal was due to the ionized Be3 (OH)3+3 or Mg (OH)+ . Variations in the electrokinetics of quartz were minimized by heating the sample to 300° C.

Jan 1, 1968