Search Documents

By L. L. Lacerda, A. J. Blair

The Wolf Creek Upper Narrows Tunnel (Upper Narrows Tunnel) is one of the first major highway tunnel in the United States implementing the use of spray-on membrane for purposes of constructing a double-shell drainage solution between an initial shotcrete lining and a final cast-in-place concrete lining (Figure 1). In the case of the Upper Narrows Tunnel the primary membrane is constructed with a spray-on product manufactured by Degussa, namely Masterseal® 340 FA (MS 340) that has been utilized previously in other tunnel projects. Shotcrete-like in application, but differing in physical properties, MS 340 is now outdated, and is succeeded by Masterseal® 345 (MS 345), a nearly identical product, with improvements in material properties. Tunnel project histories utilizing either MS 340 or MS 345 are discussed and summarized with regard to the respective motives for prompting spray-on membrane selection and the realized benefits resulting from spray-on membrane construction. With an emphasis on the Upper Narrows Tunnel, project summaries discuss details of the aspects of design for spray-on membrane construction methodology as opposed to conventional sheet membrane construction methodologies. It is anticipated that experience gained during the construction of the Upper Narrows Tunnel with respect to other tunnel projects that have utilized spray-on membrane will be of use for future tunnels employing spray-on membrane in drainage solutions.

Jan 1, 2005

By J. D. Miller, R. J. Smith

Earl C. Herkenhoff Publication of the article "The Flotation Behavior of Digested Asphalt Ridge Tar Sands" by R.J. Smith and J.D. Miller has confirmed and again spotlighted a most significant and important development in the field of tar sand and heavy oil mining. This is the ability to recover 95 % of the bitumen in dry tar sands by a hot water process. The initial investigation by Miller and Sepulveda in early 1978, "Separation of Bitumen from Dry Tar Sands," was the first blockbuter. It is disappointing that there has been so little scientific and industry ackowledgement that the authors laid to rest the long entrenched belief that the sand grains had to be "water wetted" for a hot water process to be applicable. Dr. Miller and his researchers at the University of Utah used slightly different mineral dressing terminology in describing their process but it is essentially the old, established technique of high solids attrition scrubbing at elevated temperatures with a conditioner or modifier, followed by dilution and froth flotation. Similar techniques were described in detail for other nonmetallic minerals in the mid-1940s by Stuart Falconer of American Cyanamid Co. The authors used a 15-minute "scrub" period (or in their terminology "digester step") at 73% solids and 95°C (203°F) in a 0.3 m solution of sodium carbonate -about 4 kg/t (8 lb per st) of tar sand. Flotation was at 10% solids. Obviously, the scrub is an expensive step with respect to energy input but the high recovery of bitumen appears to justify it. Two basic questions then arise: • What are the effects of shorter scrubbing time, lower temperature, and less sodium carbonate? • Would a two-stage approach be advantageous? That is, could you get the major proportion of the bitumen with a mild scrub and apply the high power and temperature only to the refractory portion? These variables should be evaluated. Apparently, all results were only for rougher flotation. What would the grade and recovery of bitumen be if multiple cleaner flotation steps were employed? We must concede that a 60-62% grade of bitumen leaves considerable room for upgrading. Finally, it should be noted by all executives who approve funds for heavy oil recovery schemes, most of which are variations of in-situ methods, that mining can yield a 95% recovery of bitumen. That is correct, 95%. Imagine what that does to the total barrels recovered from a heavy oil resource compared with the scrawny 30-35% maximum recovery we are getting now. The conclusion-let's mine heavy oil and tar sands. Reply by R.J. Smith and J.D. Miller We, too, share Mr. Herkenhoff s enthusiasm for the mining of tar sands-heavy oil and continue the development of related processing technology. Specifically, it will be noted that by appropriate control of bitumen viscosity in the feed (probably the most important variable for successful separation) the recovery can be accomplished at low digestion temperature and low addition of alkali. A 91 t/d (100 stpd) pilot plant based on our technology is now being operated by Enercor in Salt Lake City (Hatfield, Oblad, and Miller, 1982). In these same pilot facilities, rougher concentrates containing more than 80% bitumen on a dry basis are being produced from Asphalt Ridge Feed. However, the processing of certain other tar sands results in incomplete digestion of bitumen/sand aggregates as discussed elsewhere (Miller and Misra, 1982). Such undigested aggregates are shown in Fig. 1. In this regard, it is intended that a recycle stream will be installed in the pilot plant to provide for redigestion of middling products. Further details regarding surface chemistry aspects of this tar sand technology have recently been published (Misra, Aguilar, and Miller, 1981). References Hatfield, K.E., Oblad, A.G., and Miller, J.D., 1982, "Pilot Plant Recovery of Bitumen from Oil Wet Tar Sands," Processing, Second International Conference on Heavy Crude and Tar Sands, Caracas, Venezuela, Feb. 7-17. Hatfield, K.E., Oblad, A.G., and Miller, J.D., 1982, "Pilot Plant Processing of Oil-Wet Tar Sands," Symposium, Rocky Mountain Fuel Society, Salt Lake City, Utah, Feb. 18-19. Miller, J.D. and Misra, M. 1982, "Hot Water Process Development for Utah Tar Sands," Fuel Processing Technology, Vol. 6, No. 1, April, pp. 27-49. Misra, M., Aguilar, R., and Miller, J.D., 1981, "Surface Chemistry Features in the Hot Water Processing of Utah Tar Sand, Proceedings, "Symposium of Separation Science and Technology for Energy Applications," Gatlinburg, Tennessee, May 5-8.

Jan 11, 1982

By James Parkes

"The proposed Baltimore Red Line light rail system includes a 3.4 mile downtown tunnel (DTT) with five underground stations. The design of the underground stations involved overcoming several challenges, including limited right-of-way, high groundwater and uplift pressures, and metamorphic rock within the station depths. An innovative design was developed to maximize the internal station space while minimizing cost. The station designs use slurry walls for temporary and permanent support and groundwater control. Depths within rock are supported with cast-in-place concrete walls, the thickness of which are minimized through the use of permanent rock anchors for support of the rock mass and slurry wall toes. Permanent tiedown anchors are used for uplift resistance, which minimizes the station depths, volume of rock excavation, and the volume of deadweight concrete. Design considerations regarding individual elements and overall integration of the slurry walls, CIP walls, and multiple anchor types are presented.INTRODUCTION The Baltimore Red Line (BRL) project is a proposed light rail transit line for the Maryland Transit Administration (MTA) that runs east to west through Baltimore City and County. The project includes the Downtown Tunnel (DTT) consisting of 3.0 miles of twin running tunnels, two portals, five underground stations, and a pedestrian tunnel, as shown in Figure 1. The tunnels have an outside diameter of 21.8 feet and are designed to be mined using pressurized face tunnel boring machines (TBMs). The stations, portals, and the pedestrian tunnel are designed as cut-and-cover structures using slurry walls (concrete diaphragm walls) for both temporary support of excavation (SOE) and permanent structural walls. The dimensions of the five underground stations are summarized in Table 1. Design challenges included limited right-of-way (ROW), challenging soils conditions, strong metamorphic rock within the station depths, and high groundwater conditions. The final station designs included innovative use of slurry walls, tieback anchors, rock anchors, and tiedown anchors."

Jan 1, 2016

By Francesco Chiappalone, Miriam Piemontese, Lance Waddel, Paolo Perazzelli, Emidio Tamburri, Roberto Schuerch

The Three Rivers Protection & Overflow Reduction Tunnel is part of the Long-Term Control Plan of the City of Fort Wayne, Indiana (USA). The 4.9 m internal diameter tunnel, of length approximately 7.5 km, is excavated at a depth of approximately 40–60 m through carbonate rocks using a slurry TBM. Due to the high hydraulic conductivity of the rock mass and the high in-situ ground water pressure (up to 6.5 bar), the management of the water inflow during the TBM advance and standstills, represents the major challenge for the project. This paper outlines the geotechnical conditions and the hazards related to the large water inflows expected in the pre-excavation phase and discusses the experience gained during the construction of the first 8,224 feet (2,507 m), (first third of the total length of the tunnel).

Jun 13, 2021

By P. M. Lin

This paper presents an overall stabilization method to eliminate the potential of reoccurrence of subsidence over abandoned mine lands. The method considers column grouting at the specific locations inside the subsidence influence areas including the distressed and stress concentration zones instead of grouting' around and beneath the damaged structures. The later method is commonly used for AML subsidence abatement at the present. By using finite element method the conditions of stress distribution in the strata before and after grouting can be calculated. The design of grout pattern includes the location and number of the grouting holes. Based on the calculation, the proposed method significantly reduces the stress concentration, i.e., the potential of reoccurrence of subsidence can be reduced or eliminated. A comparative analysis including number of grouting holes, grout affected area, stress level, and potential of subsidence reoccurrence will also be presented.

Jan 1, 1990

By Irwan Halim, Young Jin Park

A new tunnel lining was designed for rehabilitation of the existing unlined Weehawken Tunnel in New Jersey. Structural assessment using beam spring models was performed for the lining design as a drained structure at the invert with a waterproofing umbrella. Empirical Federal Highway Administration (FHWA) guideline was typically adopted for estimating hydrostatic pressure, which recommends full hydrostatic pressure at the crown and ten or twenty-five percent gradual reduction from the initial pressure toward the invert. Finite element seepage analyses were conducted for the actual conditions based on anticipated drainage behind the lining and impact on the structural design. Considerations will be provided on the existing guideline for estimating hydrostatic pressures.

Dec 1, 2022

By D. Brosnahan, J. Gathje

Newmont Metallurgical Services (NMS) recently acquired a Scanning Electron Microscope (SEM) with a JKMRC/FEI Mineral Liberation Analyzer (MLA). With the MLA software package, raw particle image and X-ray data can be converted into particle mineral maps and bulk and liberation data can then be calculated for minerals of interest. This type of quantitative mineralogical data can then be used for a wide variety of applications. Ore characterization with MLA can be carried out for existing or processing plants in development. MLA characterization of laboratory test products provides valuable liberation information that assists the research metallurgist in better planning and developing process treatment options for various ore types. This paper describes the use of MLA characterization in a copper flotation test program where the use of various testing options for arsenic depression was being evaluated.

Jan 1, 2007

By Roozbeh Afzali

Designing an appropriate tunnel blasting pattern reduces the cost of rock breakage and subsequent operations such as loading, haulage and support of tunnels. For that reason, we developed a software that designs tunnel blasting patterns. Using this software, three different tunnel blast design models based on parallel hole cut, namely, Swedish, Konya and Energy Balance, were investigated and compared for a virtual tunnel. Accordingly, blasting patterns were designed, for different cross sections. The trend of parameters such as specific charge and specific drilling as functions of tunnel cross-section was determined for each model. Our results show that, in general, The Swedish model gives lower specific charge and specific drilling compared to other models.

Jan 1, 2008

By Frigyes Egerer, Pál Bárczy

Introduction Charles III, Holy Roman Emperor and King of the Austro-Hungarian Monarchy, established one of the first mining schools in Europe on June 22, 1735, in Selmecbanya (Schemnitz in German and Banska Stiavmica in Slovakian). The old city, built around the ancient gold mines, is shown in a contemporary engraving in Fig. 1. Charles' historical decree consisted of 13 chapters and included: the deed of foundation, the definition of grants, instruction for educational policy and curriculum, disciplinary rules, and the appointment of personnel. The first professor of the school, Samuel Mikoviny, gave his first lecture the same year, in December 1735. The 250th anniversary of the establishment of the School of Mines was celebrated Sept. 2-4, 1985, in Miskolc. It was attended by representatives of other Hungarian and of several foreign technical universities. A silver medallion (Fig. 2) was issued to commemorate the occasion and a series of lectures

Jan 6, 1986

By Nancy C. Shaver, Alan Tapp

Leach pads of 272,000 tonnes (300,000 st) and 910,000 tonnes (1,000,000 st) with associated operating ponds have recently been constructed on sidehill locations with up to 20 percent slopes. The larger pad was designed in anticipation of ore heights up to 30 meters (100 feet). This paper describes site investigations and civil engineering design as well as construction experience associated with development of these pads. The leach pads were underlain by a double liner system consisting of 2 mm (80- mil) HDPE over compacted fine-grained tailings, with an intermediate leak detection layer. Both sand and geotextile drainage layers were used. Pad slopes were limited by the factor of safety against sliding on the HDPE liner. The sites for the facilities had been substantially disturbed by prior mining and construction activities. Natural conditions included peat layers and locally swampy ground. Site preparation included french drains to lower the water table and stripping of unsuitable subgrade materials.

Jan 1, 1987

By M. Prasad, G. M. Rao, A. K. Majumder, T. C. Rao

Froth flotation was employed to beneficiate a lean-grade siliceous rock-phosphate ore containing fluorapatite, the phosphate-bearing mineral. The main gangue minerals were quartz, iron oxides and aluminum oxides. After the rougher stage, four cleaning stages were required to upgrade the ore. The liberation size of the phosphate mineral was below 200 mesh, The reagent scheme consisted of commercial-grade sodium silicate and sodium oleate. The effect of reagent dosages, number of cleaning stages and pulp density on the efficiences of separation were studied systematically. A flowsheet was proposed for the processing of low-grade siliceous phosphate ore containing 12.1% P2O5, 55.36% SiO2 and 15.45% CaO. The flowsheet provided a useable phosphate concentrate containing 34.18% P2O5 and 14.20% SiO2 with a P2O5 recovery of 70.4% (the weight yield was 25.0%).

Jan 1, 1999

By J. Donald Rimstidt, Jeanette K. Jerz

Acid mine drainage is a major environmental problem worldwide. A key to remediating this problem is understanding the rate and mechanisms of the complex, multistep pyrite oxidation reaction under geologically relevant conditions. Because many waste piles are not submerged, a large amount of pyrite oxidation actually occurs in air. We have designed a Barcroft-manometer reactor to measure the rate of pyrite oxidation in air as a function of relative humidity and oxygen partial pressure. The reactor consists of two chambers joined by a manometer. Each experiment occurs at constant temperature, initial oxygen partial pressure, and relative humidity, although these variable can be changed between runs. Oxygen consumption was measured and pyrite oxidation rates were calculated from those data. Initial data indicate that rate of pyrite oxidation by oxygen in humid air is much faster than the rate of oxidation by oxygen in solution. The rates determined by this study can be used to develop better remediation techniques for acidic mine waters.

Jan 1, 2000

By Eddy J. Jacques

When the automatic control of a ventilation process is considered, and supervising expert systems need to be designed, an important problem to address is: what will be the optimal set points of the regulators that should meet a certain number of independently formulated requirements, distributed over a ventilation network? The set of these requirements, expressed in terms of air flow quantities or differential pressures in certain airways, need not be consistent. Their number is not limited by the number of available regulators, nor by their nature, i.e. passive or active. Moreover, they may be subject to upper or lower limit values. The method described here addresses this problem and tries to provide a tool that should allow to calculate the set points of all the regulators as a global and optimal solution with respect to this set of distributed requirements. The pure mathematical developments in this paper are kept as short as possible in order to allow more room for the description of a relevant example.

Jan 1, 1991

By Samuel M. Cassidy

The exact date of man's first use of coal is lost in antiquity. The discovery that certain black rock would burn was undoubtedly accidental and probably occurred independently and many times in the world over thousands of years. It is quite likely that these independent discoveries were made when primitive man chanced to build camp fires on exposed ledges of a black rock, then was amazed when it caught fire. The Chinese recorded the use of coal 1100 years before the Christian Era and from the Bible we learn that King Solomon was familiar with coal in what is now Syria. In Wales, there .is evidence that the Bronze Age people used coal for funeral pyres, and it is known that the Romans used this fuel. There are other ancient references. So the knowledge that coal would burn, and even some uses of that knowledge, go back thousands of years. However, practical and consistent use of coal seems to date to England in the Middle Ages.

Jan 1, 1981

By Asa Weber

With continuing pressure from stockholders not only to maintain but to increase mineral revenues, producers have increased plant capacity. Depressed mineral prices have accentuated the trend toward higher production rates to maintain consistent cash flow, and these same trends have promoted the development of large-scale processing equipment. In addition to the need to handle increased throughput, larger flotation equipment can result in decreased capital-equipment and operating costs. The development of larger column and conventional flotation equipment relies, in part, on suitable scale-up procedures. To properly scale-up large flotation cells and columns, certain constraints and design parameters must be taken into consideration, including velocities in the vessel, residence time, solids suspension, and lip loading. This paper will review the design constraints and scale-up criteria for WEMCO® flotation cells. Scale-up criteria are augmented with computational-fluid- dynamics analyses and high-speed imaging techniques, as well as multiple regresesion analysis of in-plant operational data.

Jan 1, 1999

By Paul C. Miclea, Robert E. Murphy

The behavior of fire and airflows in a confined tunnel differ significantly from more familiar fire situations outside, due to the buoyant effect which tends to create a layer of hot smoke and gases flowing away from the fire near the crown of the tunnel, while air supporting combustion moves toward the fire beneath the smoke layer. A subway emergency ventilation system is designed to force air to flow through the tunnel, shifting the balance of heated air in the direction of the forced flow and avoiding the "back-layering" of hot gases and fumes. This paper presents a computer program, called the "Subway Environment Simulation" (SES), which can be used to predict airflows created by the emergency ventilation system. It utilizes the latest state-of-the-art analytical treatment of fires in enclosed spaces, including observations from mine fires and gas explosions. The program allows designers to reduce construction cost by identifying unnecessary ventilation shafts and by verifying fan capacities. In addition, the program allows the designers and operators to determine safe evacuation routes, in case of a train fire, by predicting the occurrence of back-layering. It can be used to determine when the ventilation system can control the direction of smoke movement to provide a clear and safe path for evacuating people and facilitate fire fighting operations.

Jan 1, 1989

By Robert M. Matyas, P. E. Sperry, Robert J. Smith, A. A. Mathews

INTRODUCTION The first Dispute Review Board (DRB) was utilized on a tunnel project 20 years ago. Increasingly utilized on a wide range of construction projects, DRB's are becoming the norm on tunnel and underground projects. This paper summarizes the growth in this usage, uses observations and experience to establish that barriers to the utilization of DRB's are more perceived than real and that many arguments against the DRB concept are not valid, and notes some of the salient elements that should be considered in practice to optimize DRB effectiveness. The purpose of the paper is to provide an annotated checklist for current and prospective users. The basic concept, structure, and operation of DRB's are described elsewhere and will not be repeated here (ASCE, 1991). DISPUTE REVIEW BOARD USAGE A compilation of Dispute Review Board usage for tunnel and underground projects to January 1994 indicated use on 63 contracts with a cumulative construction value of $3.8 billion and a total of 60 disputes settled. As of that same date, DRB's were planned for another 63 contracts with an estimated construction value of $4.7 billion. (A listing of these 126 projects is available from the authors.) This success and popularity have spread to other civil projects as well as process and building construction. The increase in DRB usage has been exponential. See Figure 1.

Jan 1, 1995

By P. Campbell, E. M. Gardy, L. Hachkowski

Introduction The efficient process control of a uranium mill and its associated mining operation requires a nearly continuous knowledge of the uranium concentration in the ore. Generally, the approach is to use laboratory assays of grab samples from the mill feed belt. In some cases, elaborate and expensive systems have been used to ensure random sampling, but even with these systems, mass-balance discrepancies still exist. There is a requirement for an on-line instrument that can give a prompt, accurate analysis of a large portion of the feed stock. The authors have recently evaluated a laboratory system that achieves these goals using neutron activation and delayed neutron counting. The development of the on-line uranium ore analyzer is a consequence of previous work done at the Whiteshell Nuclear Research Establishment (WNRE) (Campbell et al., 1978 and 1981), and is based on the emission of delayed neutrons after the neutron irradiation of fissionable materials. The mechanism of delayed neutron emission has been described (Keepin, 1965), but briefly is as follows. The fission fragments resulting from irradiation are in an excited state. Certain of these delayed fission products, precursors, decay to a more stable state by the emission of a delayed neutron. The delayed neutrons can be divided into six groups with effective half-lives ranging from 0.2-55 sec. It is important to note that more than 50% of the delayed neutrons are emitted within the first 6 sec after irradiation; this has an influence on the design of the analysis instrument. Measurement Cycle The measurement cycle involves a neutron irradiation, a delay time, and a counting period. The laboratory demonstration model of the ore analyzer comprises a californium-252 neutron source, a source chamber, a pneumatic transfer facility, and a neutron irradiation and counting module (Fig. 1). The ore sample is placed in the irradiation chamber. The neutron source is transferred to the center of the chamber for a 5-sec irradiation while the helium-3 thermal neutron detectors are switched off. As the source returns to the storage chamber, the detectors are switched on and the delayed neutrons counted. The total assay cycle is 16 sec. The current instrument design calls for the ore to be cut from the main belt every 16 sec by a mechanical arm and dropped into the analyzer directly, or via another belt. The cycle starts when there is a sufficient mass of ore in the irradiation chamber to depress a switch and stops when the delayed neutron count is finished. The ore is then dropped through the bottom of the analyzer chamber and returned to the main belt. The counts from each cycle are accumulated and the data reduced to give the desired information. Key for Fig. 1 A-Helium-3 neutron detector B-Wax moderator for neutrons C-Irradiation chamber D-Funnel for receiving ore E-Gate F-Transducers G-Biological shield for neutron source H-Transfer tube for neutron source I-Neutron source J- Microprocessor K-Accumulator for hydraulics L-Control panel M-Electro-hydraulic servo valve to control movement of the source N-Electro-hydraulic proportional valve to control movement of the gate O-Hydraulic power unit Irradiation and Counting Equipment Irradiation of the ore is achieved using a 1 X 10 7 neutron*s-1 californium-252 neutron source. The source is contained in an iron capsule and pneumatically transferred between the irradiation/counting and storage chambers. The irradiation/counting chamber possesses 12, 600-mm (24-in.) long helium-3 thermal neutron detectors embedded in an annulus of wax (Fig. 1). Two sets of six detectors are each interfaced to a preamplifier, amplifier and single-channel pulseheight analyzer system, and the two systems are connected to a scaler. A special timing unit controls the transfer of the source and the on and off switching of the detector assembly, in sequence with the movement of the source. Results and Discussion In the experimental demonstration, using the 107 neutron.s-1 source, a 10% uranium ore was measured to ± 10% (2o total error) in 10 cycles and ±6% (2o) in 100 cycles. Since a larger source was not available, it can be statistically predicted that a 109 neutron-s-1 source could be used to measure a 0.1% ore to ± 10% (20) in 10 cycles. The uranium can occur as discrete nonhomogeneous particles in the ore, and the error caused by such a distribution of particles is ± 4% (2o), as determined by

Jan 1, 1984

By W. J. Schlitt

Introduction Heap and dump leaching are low-cost metal production techniques that are gaining in popularity among gold and copper producers. However, the flow of solution in heaps and dumps has received little attention in the literature. This is unfortunate since solution flow is one of the few parameters subject to operator control. Thus, solution management may well influence both operating costs and plant performance. Costs aside, there are two important aspects of solution flow to be considered -the metallurgical and the hydrological. Some of the metallurgical factors have recently been discussed (Jackson and Ream, 1980; Schlitt, 1984; Schlitt and Nicolai, 1987). These cover solution application rates and methods, irrigation rates, leach-rest cycles, and nonvertical solution flow. According to Caldwell and Moss (1985), however, the hydrological aspects may be more significant than the metallurgical ones. In particular, a phreatic surface will form when excessive flow leads to an accumulation of water and the associated buildup of pore pressure within the rock pile. Such internal flooding can either originate at the foundation or at some other zone of very low permeability. The latter condition gives rise to an impounded volume of solution, i.e., a perched water table (see Whiting, 1985). Caldwell and Moss point out that a rising zone of saturation is probably the most common cause of dump failures. Of course, such failures have even occurred in heaps that were carefully prepared for leaching (Milligan and Engelhardt, 1984). Thus, flooded conditions and perched water tables represent an important safety consideration as well as having an impact on metallurgical performance. The following sections describe a case history in which a perched water table developed within a copper leach dump. The description includes background information, solution flow rates, and metallurgical data. Then this situation is compared to one involving normal drainage. Description of the leach system The leach dump in the case history is located at a shutdown open pit copper mine. It was built in two lifts, with the second added some 20 years after the first. There is little detailed information available on the initial lift. It was built with rail¬hauled waste and was generally less than 30 m (100 ft) high at the crest. The area available for leaching was about 120 m (400 ft) wide and more than 380 m (1250 ft) long. The dump surface was prepared for leaching by dozing ponds approximately 12 m by 12 m by 2.5 to 3.0 m deep (40 ft by 40 ft by 8 to 10 ft). The ponds were leached by flooding with barren leach solution returned from a scrap iron cementation plant. Based on mill feed at the time, the average waste grade was probably close to 0.4% Cu. The first lift leached well. It accepted high flows, which together with the waste grade, produced a rich pregnant leach solution (PLS). Old records indicate a PLS of "50 lb Cu/ 1000 gal," or about 6 g/L. As later drilling would indicate, such a high tenor led to dissolution of considerable scrap iron that was returned to the dump. The iron then hydrolyzed and settled out on the pond bottoms. In addition, the waste settled substantially so that the unleached crest was 3.0 to 4.5 m (10 to 15 ft) above the ponded area. Eventually, the leachable copper was extracted and the dump became less permeable. Thus, the PLS tenor dropped until it became uneconomical. About ten years later, mining resumed and the decision was made to add another lift to the dump. This was done without giving much thought to a subsequent leach operation. Hence a 24-m (80-ft) lift was built on top of the original dump. The surface of the latter was not prepared in any way, e.g., by leveling and/or deep ripping, prior to over-dumping. Examination of subsequent drill cuttings indicated that the new lift contained about 0.2% Cu, with chalcopyrite and chalcocite (50:50) being the predominant copper minerals. Most of the chalcocite occurred as rimming on the abundant pyrite, with the pyrite to chalcopyrite ratio estimated at 10 to 1. The use of 100- and 120-ton trucks for haulage caused some waste compaction during emplacement. In addition, the host rock itself was relatively soft, being a porphyry intrusive material that was partially altered to clay. As a result of the initial compaction and clay swelling, the rate of water percolation from the new leach ponds was slow and the ponds often contained considerable standing water. Even frequent ripping failed to provide a sustained improvement in the percolation rate. The poor surface permeability was exacerbated by hydrolysis of iron salts which settled as a layer on the pond bottoms. Partly as a result of the permeability problems, metallurgical performance was not up to expectations. These had been based on laboratory tests which showed about 20% copper solubilization in two weeks. Continued copper extraction in the tests also suggested that a substantial percentage of the copper would eventually be recovered. However, the PLS grade in the actual operation peaked briefly at about 0.48 g/L Cu (4 lb Cu/1000 gal), then declined to a range of only 0.24 to 0.36 g/L Cu (2 to 3 lb Cu/1000 gal). The poor leaching was traced to a lack of oxidation of the sulfides. There were two principal observations supporting this conclusion. First, there was no evidence of any heat being generated within the dump. As discussed elsewhere (Schlitt and Jackson, 1981; Hiskey and Schlitt, 1982), pyrite oxidation is quite exothermic and the high pyrite content of the waste should have led to an increase in the temperature of the leach solution as it percolated through the rock pile. Second, there was no sign of any natural convective air flow through the dump.

Jan 1, 1987

By M. D. Khattar

Problems discussed concern encountering of high temperatures [up to 66°C] and heavy flow of water [150 L.P.S] during the construction of the 10.15 MØH.R.T. for the 2500 MW Nathpa Jhakri Hydro Power Project in the Himalayas(India). Over a length of 2500 M progress of work got seriously affected resulting in excessive time for completion - two years [max. monthly progress achieved was 178 M [Heading]. Many innovative and simple steps were taken to complete the work in these inhospitable environs affecting working of both men and machines. Also it meant a review of the design of concrete lining. Other geological conditions affecting the progress are also described.

Jan 1, 1999