Search Documents

By L. Franko, S. Klima

Wet-drum magnetic separators are used extensively for upgrading iron ore and for magnetite recovery in dense-medium circuits. In this study the performance of a continuous, laboratory wet-drum magnetic separator was evaluated with and without the application of ultrasonic energy when processing dense medium slurries. Test variables included magnetic-to-nonmagnetic ratio, solids concentration, and nonmagnetic materials. The results indicate that under certain conditions, the purity of the magnetic material increased after ultrasonic treatment.

Jan 1, 2001

By Todd Minoski, Matthew McElhinney, Mark Morris, Mark Mazzella, Joseph Bright, Morgan Sears, Craig Compton

To promote the safety and health of U.S. mineworkers, researchers with the National Institute for Occupational Safety and Health (NIOSH) are currently involved in gathering additional field data from the nation’s underground coal mines. The purpose of this field study was to monitor ground movement and changes in pressure during mining where conditions include a thick parting in the coal seam. To accomplish this, three arrays of field instrumentation were installed in the wraparound bleeder of a room-and-pillar panel at the Maple Eagle mine located in southern West Virginia. Borehole pressure cells (BPCs) were used to monitor the change in pressure in pillars located adjacent to the gob. Roof extensometers were installed to measure roof sag at various horizons in the immediate roof, while rib extensometers were installed to measure displacement of the in-seam parting as mining progressed. Additionally, visual observations and manual measurements were taken during subsequent site visits. The repeatability of results, important from a scientific perspective, was accomplished by successfully obtaining field measurements from two nearly identical instrumentation sites. The data collected indicated that the front abutment extent at the edge of the panel was approximately 200 ft, corresponding to a distance of 9– 10 times the square root of the depth. Yielding of the slabbed pillar began when the pillar line was approximately 290 ft outby the instrumentation sites. This was followed by load shedding onto the abutments and the measurement of small amounts of roof sag in the No. 1 entry. Instrumentation data, as presented in this paper, can be used to better understand stress redistribution, pillar performance, and roof/rib displacements. Additionally, this data is suitable for assisting in the calibration of numerical models. Insight gained from applying these models can be used to make better engineering-based judgments for conditions that could potentially be encountered in the future.

Jul 1, 2023

By Don W. Deere

Faults under high rock cover represent some of the most severe ground conditions a Tunneler can encounter. High ground water pressures and flows are usually associated with mountain faults. Ground behavior can range from blocky ground to flowing sands and squeezing clays. Sticking a IBM within a fault zone for many weeks, with the disastrous financial consequences, is still a common occurrence. Interpreting the geology and detecting the location of a fault prior to penetrating it is a fundamental step to successful tunneling. Ground water control through predraining or pre-grouting is the second fundamental step. This paper discusses techniques applied for detecting and crossing mountainous fault zones through the use of case histories across the globe.

Jan 1, 2007

By C. E. Golson

The preparation of aggregates is a form of mineral processing which has been taken for granted for many years, mostly because of its lack of glamour when compared to the winning of metallic minerals from their ores. Many of the processes and equipment now used in the metallic mineral processing industries originated in the more prosaic preparation of aggregates. 'Their adaptation to metallurgical processes has led to developments both in their design, and in their use. Modern practice, has been so exacting in its demands that, in many cases, this improved technology is finding new applications in the very industry in which it originated the mineral aggregate industry, The low cost requirements, large tonnage capacities and complex specifications which govern the acceptability of its products have node modern aggregate processing a much different art than it was one or two generations ago. The basic conditions which govern the type and quality of mineral aggregates were presented in an addendum to a paper given at the San Francisco Meeting in 1959 by one of the authors.

Jan 1, 1961

By George L. Wilhelm

Many factors, some of which are not easily defined or described, must be considered in the design of a hydraulic backfill system. After participating in the design of several plants, I have a conviction that future refinements in sandfill systems must come in large part, from the merging of good design ideas and information from existing operating plants. It is important then, that we document and publish information on existing plant designs and their operating characteristics. This information will then be available for use by our successors and later innovators in hydraulic fill placement. The Mayflower hydraulic sandfill system is similar to other plants. The intent of this paper is to describe only this system's unique design and operating characteristics. I will not describe in any detail, the familiar elements of the system. I will document some of the observed hydraulic characteristics of the system, elaborate on some of the design situations that had to be solved, and will discuss operating factors that are not generally described in our technical literature.

Jan 1, 1968

By A. G. Sciulli, G. P. Ballock, K. K. Wu

Waste disposal underground is the most effective method when viewed from an environmental aspect. As costs of other methods of disposal continue to escalate, the cost effectiveness of underground disposal during the mining cycle becomes increasingly attractive. The use of concrete for sealing abandoned mines has proved to be suspect when associated with a relatively incompetent adjacent strata due to its shrinkage characteristics. Complete failure of the plug has been known to occur in some instances. A more effective, cost competitive seal can be obtained using pneumatically stowed material and incorporating a polyurethane grout, which has greater adhesion characteristics than concrete. Injection of the surrounding strata and of the stowed material helps to ensure an impervious barrier and prevent the plug from moving when subject to high pressure heads. When properly placed, impervious seals cause the old workings to flood, raise the mine pool level, and thus eventually eliminate the potential for oxidation, which is the primary cause of acidity in the water.

Jan 11, 1986

By J. K. Lemley

The human element in large measure dictates success in contracting relationships. Because of our professional backgrounds, we view contracts primarily as either engineers, contractors or owners. A beneficial contractual environment--one in which decisions, risks and benefits are shared--demands equal consideration of all three points of view. Most of the older cities in the United States, for example, suffer from bad contracts--generalized, patched-together documents that represent an accumulation of modifications originally written to compensate for specific situations that have occurred over the years. Because such documents lack coherence, they often present conflicting instructions which lead to defensive, ultimately destructive attitudes among the parties involved in the day-to-day administration of the project. Good contract development begins with a strong central philosophy to which the details of the contract can be related. First, the owner should establish a comprehensive philosophy in which risks between the parties are identified. Following this, a specific contract document can be written to satisfy this established philosophy. The contrast between two opposed contractual situations, NYC Water Tunnel Number Three and the Seabrook Nuclear Power Plant Cooling Water Tunnels, illustrates how comprehensive, well-written contracts--contracts which share both risks and benefits--provide the basis for achieving quality construction that will reward engineer, contractor and owner.

Jan 1, 1983

To maintain its brand position in the competitive market of mining equipment, the Volvo Construction Equipment (Volvo CE) engineers were challenged to develop top-performing wheel loaders and articulated haulers even faster than before. To start, this meant reducing prototype test cycles by two-thirds. The final goal? Chopping in half the virtual prototyping time in early design phases. Creating a unified co-simulation solution In this ground-breaking project, the Volvo Construction Equipment design team in Eskilstuna, Sweden, replaced its piecemeal department-by-department process with a single solution based on LMS Imagine.Lab AMESim. With one unified model, they could simulate the behavior of four major vehicle subsystems in wheel loaders and articulated haulers: hydraulics, powertrain, thermal management and the actual driver. Subsystem models exchanged data seamlessly.

Jan 1, 2011

By L. Alagha, O. Molatlhegi, S. Khatibi

"In the present study, the effect of organic/inorganic (hybrid) polyacrylamide polymer on fine coal flotation was investigated. Raw coal samples contain about 37% of ash-forming mineral at a feed size of -75 + 38 um were subjected to flotation tests in the presence of in-house synthesized hybrid Al(OH)3-PAM at different polymer dosages and pH values. Results show a significant improvement in both combustible recovery and ash rejection at 1 ppm polymer dosage. Further improvement of combustible recovery was obtained when flotation was performed at pH 5. Interfacial properties of coal particles before and after flotation were examined through electrokinetic (zeta potential) measurements of coal/water slurries. Zeta potential vs. pH curve were established and compared. In the case of raw coal/water slurry, zeta potential-pH curve resembles the ash-forming minerals (silica and clays) more than coal. After Al(OH)3-PAM-assisted flotation, the zeta potential of froth/water slurry shifted to more positive values point which strongly indicates significant removal of ash-forming minerals from coal by Al(OH)3-PAM. INTRODUCTION Coal has been a major commodity in meeting the world energy demand during the past several decades (Milici et al., 2013). According to the international energy agency, global coal demand will continue to increase for the coming decades. With increasing world population, the global electricity demand would also increase as more people would get access to basic electricity especially in developing countries (Maggio & Cacciola, 2012). Due to this increase in energy consumption, operations in coal mining and beneficiation processes have been highly mechanized to meet the demands. This mechanization has increased the quantity of raw fine coal particles produced which contain high amount of ash-forming mineral matter (slimes). Aplan et al., have reported that the major constituents of ash-forming minerals in U.S.A coal are clay minerals such as kaolinite, montmorillonite and illite (Aplan, 1997). Conventional froth flotation for fine coal cleaning suffers mainly from two major problems: 1) Low recovery of ultrafine coal particles due to slime coating by ash-forming minerals, and 2) The lack of selectivity, which results in the flotation of middlings and entrainment of mineral fines in the froth (Polat et al., 2003). Slime coating on both valuable and air bubbles have been proposed to explain the observed reduction in flotation recovery especially when fine grinding is required. In this case mineral matter may be degraded to extremely fine or colloidal sizes thereby creating difficulty in the water clarification process such as flotation. Slimes inhibit bubble-particle attachment, and increases reagent consumption due to the increase in solid/liquid interfacial area, resulting in low coal recovery."

Jan 1, 2015

By Gary Brendel

India produces about 70 Mt/a (77million stpy) of coal ash (fly ash and bottom ash) from burning about 200 Mt/a (220 million stpy) of coal for electric power generation. The average ash content is 35%. In contrast, the United States produces about 70 Mt/a (77 million stpy) of coal ash from burning 800 Mt/a (880million stpy) of coal for power generation. Its average ash content is less than 10%. In 1998, GAI Consultants Inc.(GAI) embarked on a federally funded, multiyear project to assist the government of India in solving its growing coal-ash management problem.

Jan 1, 1999

By Tsutomu Yanagase

Non-ferrous smelting industry in Japan often had the severe problems about the over production of sulfuric acid. There has been such a closed relation between amount of sulfuric acid from non-ferrous smelting industry and the products of copper, zinc and lead metals that the production of one ton of copper accompanies three tons of H2S04. When the proper balance exists in both markets this situation certainly brings bigger profits. In Xining and Metallurgical Institute of Japan the research commitee concerned with the fixation process of sulfur in non-ferrous smelting industry was established in 1977 and continued the activity for four years untill 1981. This paper will introduce some of the activities involved in the report published by the committee.

Jan 1, 1982

By Alan Zeni

Blind shaft drilling equipment has not changed substantially since the 1970s. Since it resides in a niche market between conventional shaft sinking and raise boring, the relatively small demand has resulted in some stagnation of development. In the 1990s the technology found a larger foothold in foundation and deep piling work for civil construction. WIRTH GmbH from Erkelenz, Germany has been servicing this market for many years with pile top drilling rigs and tools. Frontier-Kemper Constructors, Inc. recently entered into an agreement with WIRTH to develop a new generation of large diameter blind drilling equipment more specifically aimed at mining needs. The, recently completed, DHI-240 is the first rig to apply the most recent technology. This machine made its commercial debut in the fall of 2008. A description of the technology and a short case study of the first project will be described

By Lei Fu

In the wake of the collapse of the ceiling panels in the I-90 section of the Central Artery/Tunnel (CA/T) Project in 2006, the long term performance of tunnels became the focus of the tunneling industry. At the time of the accident, the tunnel had been open to traffic for about 10 years. This paper will discuss design methods and considerations to improve the long term performance and durability of a tunnel. The major problems found during the inspection of several tunnels will also be presented and the causes for these problems will be discussed.

Jan 1, 2008

By Ian Farmer, Nigel Glossop, Philip Garritty

Performance of tunnel boring machines - usually expressed in terms of penetration per revolution - is determined by relations between machine thrust and torque, head diameter and rock strength. It can be shown that for a given machine power and head diameter there is only one rock strength at which the machine performs optimally. In weaker rocks the available torque limits performance and in stronger rocks, the available thrust. Performance data shows that, historically, machines have been designed to cut weaker rocks. Optimization of thrust is required to improve performance in stronger rocks.

Jan 1, 1987

By Peter Loehr

Full-face tunnelling machines were introduced into German coal mines 12 years ago. It was aimed to utilize these highly efficient systems to drive mine tunnels in rock so that the large demand for development work in some mines could be met. A characteristic feature of coal deposits in Germany - and particularly in the Ruhr Area - is a thick overburden strata. Access is therefore only possible through vertical shafts. A network of horizontal drivages leading from these shafts open the deposits between the different mine levels. The hardcoal-bearing formations are multi-folded and heavily tectonically stressed. Apart from a few extensive fault zones there are many single faults of different natures in the carboniferous strata. During the course of decades coal mining has penetrated to ever increasing depths. Nowadays coal is mined from depths of between 600 m and 1,200 m. The effects of ground pressure in connection with extremely varying rock strengths and high temperatures are particular difficulties which have to be overcome during drivage work. The first full-face tunnelling machines to be applied in the mines had originally bee deigned and developed for tunnelling projects. Not only the machines themselves, but also the back-up equipment had to be adapted to meet the special demands of German coal mines.

Jan 1, 1983

Because of complex geological environments, a number of coal reserves occur in inclined or dipping coal seams in certain parts of the world. Longwall top coal caving using split-level a singleentry panel system (SSPS) has been widely used for extracting such coal seams with large thicknesses (greater than 6 m) in China because SSPS can reduce or mitigate problems of coal outbursts, gate road deformations, overturning of shields, downhill sliding of shearer and armored face conveyor (AFC), and so forth, during mining of inclined coal seams. Depth of yield is the range of yield coal from the rib of the pillar to the boundaries where yield ends. It plays a significant role in maintaining the gate pillar stability. This paper presents a study on the stability of an unconventional water-obstruction gate pillar (UWGP) formed by SSPS to prevent water inrush in mining of an inclined thick coal seam in a coal mine in China. As the shape of this pillar is non-cuboidal, nonparallelepiped, a conventional empirical or analytical method is not applicable for studying its stability.

Jan 7, 2020

Remote methane detection State and federal regulations require frequent measurements to verify that safe methane levels are maintained in underground coal mines. Ventilation control is the primary means of maintaining safe methane levels. In the immediate face area, where the highest methane levels occur, methane measurements are required every 20 minutes during active mining. To perform these measurements, temporary roof supports must be erected. This allows a miner to reach the face. There a hand-held methanometer is used to make the measurements. This procedure is time consuming and potentially hazardous. To facilitate the measuring process and reduce the miner's exposure to roof falls, the US Bureau of Mines has developed a prototype optical device. It can measure methane remotely from distances up to 12 m (40 ft). The device uses two infrared signals, reflected from the coal face, rib, or roof. One signal is absorbed by the methane, the other is not. The ratio of the two signals determines the average methane concentration in the face area. The prototype detector has also been successfully tested at the Lake Lynn, PA Laboratory. Instantaneous responses were obtained for methane in the ventilation airflow and for methane layered near the roof. Conventional methanometers required from five to 25 seconds to respond to the methane in the ventilation airflow. They did not respond to methane in the roof layer. For more information about the Bureau of Mines' remote detection research, contact Richard W. Watson, US Bureau of Mines, Pittsburgh Research Center, Box 18070, Cochrans Mill Road, Pittsburgh, PA 15236 or call (412) 892-6630. Ignition suppression system The incidence has increased of fractional spark ignition at the mine face. One reason is the advent of mechanical mining. Another is the more difficult ventilation conditions associated with deeper and more extensive underground workings. To cope with the problem of frictional ignition, the Bureau of Mines initiated research to develop a system that would provide rapid detection of incipient methane-air ignition. Then, rapid dispersion of a quenching agent would ensure that the methane flame was extinguished while it was still relatively small. This concept was successfully demonstrated by suppressing explosions in the Bureau's Bruceton, PA experimental mine. But the bulkiness of the early storage-dispersal system proved impractical to retrofit onto face equipment. In a cooperative effort by the Bureau and the Mine Safety and Health Administration, a more compact system has been developed and is being tested. A continuous mining machine has been equipped with four 1.8-m-long (6-ft-long) and two

Jan 9, 1987

By John Parianos

"Seafloor mining provides significant potential economic benefits for many Pacific nations that may be "land poor" but "coastline rich," meaning they have the potential to utilize and profit from the mineral wealth within their Exclusive Economic Zones that extend 200 nautical miles (360 km) out from their coastlines. The Independent State of Papua New Guinea (the State) recognizes this tremendous opportunity and is taking a leadership role in this emerging industry by becoming a 15% partner in Solwara 1 (with an option to increase their investment to 30%).The Solwara 1 Project has been gaining momentum since Nautilus Minerals and the State signed an Agreement on April 24. This new agreement with the State in which they have staked a minimum 15% interest as a meaningful partner, underscores the State’s continued and widespread support for the Project. Signing of this Agreement was a historical occasion and a milestone achievement for Nautilus Minerals and the people of PNG.The machinery being built for the Solwara 1 Project is taking shape. The Seafloor Production Tools are now over 90 percent complete. Assembly of the biggest tool, the Bulk Cutter, was completed in April this year and assembly work on the Collecting Machine and the Auxiliary Cutter commenced in May and June this year respectively. The Riser and Lifting system, which will be used to transfer the mined material from the seafloor to the surface within an enclosed system, is over 50 percent complete. The critical path for the Solwara Project is to secure a suitable vessel arrangement. Nautilus aims to have this completed by the end of this year."

Sep 1, 2014

By Marion Loomis

Environmental regulation is an ever growing cost to the mining industry. Requirements for such items as air quality modeling, hazardous waste disposal, selenium concentration in water and sagebrush planting consume more of the mining industry’s resources each year. The mining industry is willing to make the necessary financial commitments to assure that the air, land and water resources are adequately protected and restored. However, it is sometimes difficult to explain to management and stockholders why money should be spent on a specific issue when science and common sense indicate it is being wasted. Common sense and sound science should dictate how mining is regulated.

Jan 1, 1994

By H. A. Taylor

Graphite is elemental carbon that crystallizes in the hexagonal system as six-sided platelets. It occurs naturally and is mined. And it can be made artificially from petroleum coke in the form of shapes (electrodes) and powders. The market for most kinds of graphite in most end-uses was good in 2004. The 2005 graphite market looks positive. The major graphite prices, as given in Industrial Minerals, remained unchanged throughout the year. The preliminary 2004 U.S. Geological Survey (USGS) prices for natural graphite showed almost no change for crystalline flake. They were $600/t ($544/st) in 2004 and$622/t ($564/st) in 2003. Mexican amorphous graphite was almost unchanged at $150/t ($136/st) in 2004 from$152/t ($138/st) in 2003.

Jan 1, 2005