Search Documents

A roof rating system has been devel¬oped for upper seam damage prediction during mul¬ti-seam mining based on structural and geologic conditions in the upper seam. Two primary consid¬erations -geologic and spatial - form the basis of the classification system. It includes factors commonly found in geomechanics classification systems as well as factors which are peculiar to multi-seam mining, such as those which define the two adjacent seams and the innerburden. This rating system has been applied to numerous case studies to form empirical relationships for quan-titatively predicting potential upper seam damage based on anticipated subsidence and strain values and vertical movements.

Jan 1, 1988

By David R. Baughman, Ray V. Huff, Paul D. Chamberlin

ISL Ventures, Inc. (ISLV) is developing a process for recovering gold and silver from ores using a chloride-hypochlorite lixiviant. The leach solution, composed of water, NaCl and NaOCl, is maintained at a pH of about 7. At this pH most base metals are not leached. This is important for deposits that contain cyanide-soluble copper. An inhibitor can be incorporated to slow the decomposition of the oxidant. This paper reviews the history of development, presents details of the chemistry and indicates the nature of deposits, which we believe to be amenable to production using the process.

Jan 1, 1999

By D. C. Yang, J. Ye

A comprehensive flotation study has been conducted on a Chinese fluorspar ore using the packed flotation column developed at Michigan Technological University (MTU). The results are compared with those for a conventional mechanical flotation method on the same feedstocks. Key factors controlling flotation performance of both methods are evaluated based upon a simple statistic design. The flotation concentrate produced in one stage of the packed column has 4% to 5% higher recovery and much lower silica impurity than the concentrate produced by up to six stages using a conventional mechanical cell. The results also show that the packed-column flotation process is particularly suitable for the recovery of finer fluorspar particles.

Jan 1, 1993

By J. Hazen, R. Jenner

This project was developed at the PCS Phosphate Mine in Aurora, NC. This site includes a surface mining operation, beneficiation plant and chemical processing facility located in the coastal plain of eastern North Carolina. The phosphate ore being mined at this operation is a 10 to 12 meter (35 to 40 foot) thick colloidal deposit located approximately 30 meters (100 feet) below the ground surface. The ore is pumped to the beneficiation facility where it is separated into clay, sand and concentrate streams. The concentrate product is utilized at the chemical plants to produce a wide range of products including fertilizer, industrial phosphates and animal feed products. The Cyclone Dike Builder (CDB) project developed a technique for dewatering the beneficiation tailing sand stream and providing innovative placement for dike construction. Future material balance requirements at the PCS Phosphate mine required an improvement in tailing sand placement technique to accomplish strategic objectives. The water volume of the sand slurry forces significant quantities of sand out of the dike profile during deposition. PCS Phosphate and MetPro Supply of Florida developed a mobile high-density hydro-cyclone station to remove most of the water and significantly increase the density of the sand being placed for dike construction. This high-density sand slurry is then effectively controlled using minimal heavy equipment operation.

Jan 1, 2004

By G. Wang

Industrial minerals processing has gained importance lately, not only due to its wide range of new and regular applications in processing different industrial minerals, but also due to the strict specs under which products are commercialized. Among the processes applied to industrial minerals, flotation is a leading technology. The laboratory study and commercial operation demonstrate that the sulfonated reagents are very effective collectors for industrial minerals. This paper compares synthetic petroleum sulfonate with fatty acid on iron reduction in glass sand processing and describes the effect of conditioning pH on iron reduction using synthetic petroleum sulfonate as collector, the effect of molecular weight of natural and synthetic petroleum sulfonates on their flotation performance and the enhancement made for certain products.

Jan 1, 2011

By D. Richers

When modeling predictive pit lake chemistry, groundwater chemistry is integrated with the affected portions of the wall rock and chemistry of the lake in a complex series of mixing. Fractions of the solutions impinge upon fresh, unaltered or fractured and oxidized zones of the wall containing sulfide materials and/or soluble metal/metalloid salts. Changing conditions over the short term (biannually) and long term (decades) can drive reactions allowing for dissolution or precipitation of acid rock drainage and metal leaching (ARD/ML) constituents. Local zonal variations can result in a portion of the pit releasing materials into solution; whereas other portions of the lake might favor the formation of colloids or precipitants. The proportions and character of groundwater can drive the chemistry of the pit lake provided sufficient buffering capacity is available to temper the generation of ARD in the system. For sulfide-rich systems, reduction of oxygen by rapid inundation and consumption by sulfides is key to reducing the ARD/ML. This paper presents several models of a sulfide-rich wall rock system using a range of groundwater chemistries to show these constraints.

Jan 1, 2012

By John E. Urbanic, William D. Faulkner, Robert W. Ruckel

Guidelines are presented for the selection, handling and regeneration of activated carbon used in gold recovery operations. The guidelines are based on Calgon Carbon Corporation's own investigations and experience gained in working with gold mine operators all over the world. Gold adsorption rate and adsorption capacity are shown to be independent variables thereby requiring testing of both properties when selecting activated carbon. Means of measuring these properties are provided. Historical activity tests on activated carbon are shown to be minimally useful in selecting carbon for gold recovery. Proper thermal regeneration techniques to maximize recovery of adsorption rate without weakening the carbon structure are suggested. Simple positive means of measuring efficiency of regeneration are presented. The subject of hardness measurement as a predictor of "in process" abrasion is discussed. The cost/benefit issue of carbon activity level is addressed.

Jan 1, 1986

By Rudolf E. Greuer, Xintan Chang

Mine fires have always been of great concern to mining engineers and their behavior has been studied for a long time. Although an abundance of observations exist, no satisfactory mathematical model for their interpretation and extrapolation has become known. The paper presented here tries to close this gap, making use of the laws of chemical kinetics, energy and momentum conservation. To overcome the mathematical difficulties, the fire zone is axially divided into segments and radially into sections, each one with an extension of only a few inches. Conditions in segments and sections are updated in time intervals of one second or less. To solve the large number of resulting equations, a numerical solution is performed. The model has so far been tried on timber fires. It confirms experimental observations on the ignition phases and equilibria of these fires.

Jan 1, 1987

By Duluth Engineers' Club, Engineers' Club of Northern Minnesota

"There are three distinct producing iron ranges in Minnesota, the Vermilion, Mesabi and Cuyuna. In trend the Vermilion and Mesabi are approximately parallel (E.N.E. and W.S.W.) and about fifteen to twenty miles apart. The Vermilion lies farthest north, near the. Canadian boundary. It is from seventy-five to eighty miles due north of Duluth. The length of its productive part is about twenty miles.The Mesabi Range is from fifty to seventy-five miles north and northwest of Duluth. Its length along the strike is about 110 miles, and the length of its present productive area about eighty miles. The Cuyuna range lies southwest of Duluth nearly ninety miles, and is the last of the Lake Superior iron ranges to be developed. The relative positions of the ranges are shown on an accompanying map. The Mesabi Range is by far the largest producer and contains the largest ore reserves of the three. The Cuyuna is next in quantity of proven ore, and in production since 1916, while the Vermilion is first in average quality of ore.On the west, both Vermilion and Mesabi ranges disappear beneath heavy glacial drift; and on the east, extend into Canada, the so-called Gunflint range near the international boundary being an eastward continuation of the Mesabi formation. This latter range is of no economic importance, however, at present. The exploration and development of the Cuyuna range has proved up a considerable tonnage of manganiferous iron ore, besides ordinary merchantable iron ore."

Jan 1, 1920

By Dr. H. Askew

The input needs of the steady state modelling process are outlined and a methodology for designing a plant survey to meet those needs described.

Jan 1, 1995

By David C. Girard, Larry Williamson, Leonard R. Benson, Ronald E. Bizzarri

On the east side of Washington DC, the DC Water & Sewer Authority is developing a Facility Plan for the Anacostia River CSO Control Projects, including 8 to 12 miles of CSO storage/conveyance and flood relief tunnels and associated facilities. The project includes major technical and non-technical challenges, including: completion under a Federal Consent Decree schedule; large diameter (estimated 25 to 35 ft) soft ground tunnels and shafts up to 200 ft depth; operations without use of active flow control systems; and close coordination with several major public and private construction and development projects that are being advanced in the project area.

Jan 1, 2007

By Dean Treweek, Anthony Harding

"Creating stable, safe, constructible and cost effective support to openings in segmental linings is often an important component of successful delivery of a tunnel project. The many constraints on successful implementation include operational, spatial, geotechnical, structural, and constructability. Failure to address these adequately can lead to significant impacts on cost, schedule, and safety. With reference to past project experiences, this paper provides a guide to the most commonly deployed solutions and their pros and cons to help designers quickly identify the most appropriate solutions for a particular project, or act as a starting point for developing new and/or project specific solutions. It highlights the challenges that designers and contractors must address together for successful support of tunnel openings, and the constraints that arise. It then describes the common structural forms of support, and how each form can mitigate the constraints, allowing an effective opening support system to be implemented. INTRODUCTION While only a small portion of the total excavated volume of a typical tunnel, cross passages are often one of the most complex elements of a bored tunnel to construct. Cross passages in soft ground typically involve ground improvement, groundwater control, and multiple temporary support measures to ensure safe construction in ground that has been overstressed due to the construction of the running tunnels. Permanent lining construction requires careful detailing of waterproofing and reinforcement to support both long term ground and water loads and support the broken out rings of the main lining. While there is not a great deal of literature specific to cross passage construction, the main issues are discussed in some detail by Lawrence and Taylor (2011). However, the temporary support of the running tunnel segmental linings during cross passage construction is not always given the attention it deserves. The authors have been unable to find much literature on the design of such systems, much less the considerations that have led to a particular solution. Lawrence and Taylor only mention two potential methods of support. It may be easy to dismiss the opening support as an inconsequential item, but selection of the wrong support type can have significant impacts on both cost and schedule."

Jan 1, 2016

By Robert S. Mayo

My subject today is "Drilling-and-Blasting of Small Rock Tunnels". I am sure that there will be some people, primarily college students but perhaps Consulting Engineers, who will say: "Drilling-and-Blasting? I thought that went out with the invention of the Tunnel Boring Machine". A few years ago I talked to Dick Robbins and he told me that they did not try to sell a "Robbin's Mole" unless the tunnel was two miles long. For easy calculations I use 10,000-ft. (3km) A Mole today costs about $2 million which works out to $200 per lineal foot. This is "front money". You cannot place the order unless you are the uncontested low-bidder and then you must wait at least six months for delivery. Of course you can use that time to square up your portals, ready to turn-the-eye, or maybe you have shafts to sink to reach the tunnel grade. But this is "dead-time" and it is a heck of a feeling to have a job and cannot get started on it until you get the Mole. I do not have the American figures on lengths of tunnels but there was an article a few years ago in a British magazine: NEW CIVIL ENGINEER, on this subject. This stated that 75% of the jobs in Britain which were bid were for small tunnels, 10-ft x 10-ft (3m x 3m) or smaller, and that they were less than 5,000-ft (1.5km) in length. This does not mean that 75% of the footage in Britain was less than 10-ft in diameter. It means that 75% of the jobs being bid were less than a mile in length. From my experience in the U.S. I believe that we have substantially the same ratio: so many of the jobs with which I was associated were short, 1,000-ft, 2,000-ft and sometimes 3,000-ft and the bores

Jan 1, 1981

Ground falls (roof and rib) have historically been responsible for about 50% of all fatalities in bituminous underground coal mines. In some recent years, the number of ground fall fatalities has approached zero, indicating that significant progress has been made. On the other hand, last year?s Crandall Canyon twin mine disasters, in which 9 miners perished in violent coal bumps, provided a stark reminder that complacency is premature. One important success has been a great reduction in the number of miners killed inby roof supports. Throughout the 1990?s these accounted for nearly half of all roof fall fatalities, but there have just been two inby incidents in the past 5 years. Progress has also been made in pillar recovery. Safer mining technologies have reduced the number of fatal incidents, but some recent failures have underlined the need for careful management of the retreat mining process. On the other hand, more than 400 miners continue to be injured each year by rock falling from between supports, and 100 more are injured by rib falls. Together, these two categories also account for a large percentage of recent ground fall fatalities. Available technologies such as roof screen, rib bolting, and inside control roof bolters could dramatically reduce injury and fatality rates if they were used more widely. Further advances in these areas will likely be the next big advance in ground control safety. Disclaimer: The findings and conclusions in this report have not been formally disseminated by the National Institute for Occupational Safety and Health and should not be construed to represent any agency determination or policy.

Jan 1, 2009

By D. S. Cavers

INTRODUCTION This paper discusses aspects of rock engineering applicable to surface gold mines. Discussion particularly centers on areas in which rock mechanics can enhance the mine productivity or profit- ability. Methods of analysis are discussed briefly but for more detai1s the reader is referred to the appropriate references. A team approach to the overall design of the pit generally pro- duces a better result at an overall lower cost. In particular, money is wasted by asking for a "report on slopes" and then input- ting this slope angle into a pit design and economic analysis study without further reference to the geotechnical engineer. Pit slope angle depends on slope orientation, location, pit shape, pre-existing discontinuities and mining methods. Preliminary slope angles can be produced but optimization depends on ongoing inter- action between the mining engineers, geologists and geotechnical engineers. This interaction can a1 so substantially reduce overall design time which may be critical in bringing remote plays into production. Most surface gold mines in North America are in igneous or metamorphic environments. Rock mechanics aspects discussed in this paper will be discussed with reference to these environments al- though most of the principles and comments are applicable to sedimentary environments as we1 1.

Jan 1, 1987

By David L. Gefvert

A general review of the role of cationic flotation reagents in the beneficiation of phosphate, iron, and potash ores. The three major types of cationic collectors-amines, ether amines, and condensates will be compared and contrasted. The effect of particle size, water chemistry, and water temperature on the choice of cationic flotation reagents for each industry will be discussed.

Jan 1, 1986

By V. Nenov

The study is based on the so called METASEP process which includes selective sorption of heavy metals by special bonding agents (BA), separation of boding agents from the water by means of microfiltration and/or flotation and regenerating the loaded bonding agents, leading to a metal concentrate for reuse or discharge. The bonding abilities of different bonding agents suitable for application in METASEP process were evaluated. Two groups of BA are studied, namely: chelating ion exchange resins and water soluble oligomers. The group of ion exchange resins studied includes eight organic resins, mostly chelating cation exchangers and representatives of conventional strong and weak cation exchangers. The resins with iminodiacetic and aminomethyl phosphoric acid groups showed highest affinity towards several heavy metals. The study of resin particle size showed that this parameter is a key factor influencing the kinetics of heavy metal sorption. The group of water soluble oligomers (WSO) includes polyvinyl alcohol, carboxyl-methyl-cellulose, polyvinylethylenimin and pectin. The Metal-WSO complexes were separated by Ultra Filtration. The effect of Metal-WSO mole ratio and pH was studied. Depending on the operational conditions the heavy metal retention varies within 68-99%. It was shown that regardless of pH and mole ratio Metal-WSO, separation of certain ion from the metal mixture is not possible.

Jan 1, 2006

By D. L. Misterek, E. J. Slebir, G. W. Ring, M. A. Laird

INTRODUCTION In 1973, the Federal Highway Administration (FHWA) initiated a 10-year program of research on tunneling technology for future highways as a part of a larger Department of Transportation effort on tunnels. The objectives of the FHWA program are to: improve tunnel design technology, reduce costs, minimize adverse environmental impact due to construction, increase the rate of construction, and assure the maintenance of a safe and attractive tunnel environment. The program is divided into four research tasks designed to solve tunneling problems identified by the engineering and field offices of the FHWA. These tasks are as follows: 1. Cut-and-Cover Tunneling 2. Site Investigations 3. Ground Movements - Prediction and Control 4. Highway Environmental Criteria for Tunnels In order to provide input into Tasks 2 and 3, the FHWA is sponsoring an investigation and testing program by the U.S. Bureau of Reclamation to instrument and monitor two sites in the second bore of the Eisenhower Memorial Tunnel located on Interstate Highway 70 at Loveland Pass approximately 97 km (60 miles) west of Denver, Colorado. The tunnel will be approximately 14.0 m (46 ft) in diameter when excavated. The study is designed to generate data on: (1) changes in the state of stress, and movements during and after tunneling, (2) tunnel lining design requirements, (3) developing a

Jan 1, 1976

By Robert T. Tape, Thomas G. Harper

Valley-fill heap leaches built in steep terrain over low-friction angle liner system may be unstable even though analyses indicate stable ore slopes. This paper demonstrates the potential for massive heap failure using stability analyses which consider both heap slope and heap mass failure considerations. The computations presented also reveal the sensitivity of mass heap stability to liner friction angles.

Jan 1, 1987

By D. Malhotra

This paper discusses the need for periodic auditing of mineral processing flowsheets and the potential benefits a company can gain from a study of this nature. A carefully designed flowsheet audit can have a significant impact on the metallurgical performance in the plant. Several case studies illustrating the potential benefits that can be attained from flowsheet auditing of mineral processing plants are discussed.

Jan 1, 1988