Search Documents

By D. K. Grubbs

Anorthosite is an abundant, domestic source of alumina with reserves in individual deposits ranging from a few billion to hundreds of billions of tons. While anorthosite contains less alumina than does kaolinite, its CaO and Na20 contents are significantly higher (Figure 1). Alumina can be produced from anorthosite by alkaline, soda-lime sinter or acid processes. CaO and Na20 are advantageous because they are reactants consumed in alkaline processes. Acid processes require high calcium plagioclase feldspars (bytownite-anorthite) to obtain high alumina extraction because the lower calcium plagioclase feldspars (andesine-labradorite) are not as readily dissolved during digestion. The layered Raggedy Mountain Gabbro group in the Wichita complex in southwest Oklahoma is a high calcium anorthosite that could be processed by acid, sinter, or alkaline methods. Chemical grade limestone in the Arbuckle Group is located within 45 km of the anorthosite (Figure 2).

Jan 1, 1980

By B. K. Parekh

Economical dewatering of ultra-fine (minus 74 m) clean coal slurry produced in column flotation to a 20 percent or lower moisture level will be an important step in successful implementation of the advanced fine coal cleaning processes. The main objective of the present study was to evaluate efficiency and effectiveness of three dewatering techniques, namely, hyperbaric, vacuum and screen bowl centrifuge, in dewatering of ultra-fine (D50 -25 m) clean coal slurry produced by the 'Ken-Flote' columns operating at the Powell Mountain Coal Company, St. Charles, Virginia. he hyperbaric filter using 3 bar pressure and 1650 cake formation angle, provided a filter cake with 23.6 percent moisture with a throughput of 800 Kg/m2-h and air consumption of 868 Nm3/t (460 scfm/t). The vacuum filter with 30 percent submergence provided a filter cake with 27.8 percent moisture with a throughput of 122 Kg/m2-h. The screen bowl centrifuge provided a dewatered product containing 32.9 percent moisture at a feed rate of 450 Kg/hr, however, the solids capture was only 65 percent. Addition of 1 Kg/t of a cationic surfactant provided filter cakes with 19.1 percent, 23 percent, and 34 percent moisture using hyperbaric, vacuum, and centrifuge, respectively. Similarly, addition of 0.5 Kg/ton of copper chloride lowered filter cake moisture to 20.7 percent and 24.8 percent, using hyperbaric and vacuum. With the centrifuge no improvement in filter cake moisture was noted. However, use of 80 Kg/ton of 'orimulsion' in the centrifuge provided dewatered product containing 26 percent moisture, and the solids capture increased from 65 to 95 percent. The dewatered product appeared dry and was easily handleable.

Jan 1, 1999

By Christopher Mark

Sixty years ago, underground coal mining was the most hazardous job in the United States. Roof falls killed about 100 miners every year, more than all other causes put together. Fast forward half a century to 2016, and the first year ever with zero roof fall fatalities. Just three miners were killed by roof falls during the following six years. To understand how this historic goal was achieved, this study analyzed hundreds of roof fall fatality reports covering five decades. It found that the immediate effect of the Federal Coal Mine Health and Safety Act of 1969 (Coal Act) was to reduce the riskiest activities, like needlessly going under unsupported roof. Other hazards, like large roof falls, required technological developments before they were brought under control. Roof control plans, which the U.S. Bureau of Mines had been advocating since the 1920s, fostered the necessary improvements in both the safety culture and the mining technology.

Jun 1, 2024

By R. D. Auten

This paper is primarily a report on the process of using oolitic aragonite, as received from Marconi& Ocean Industries, Ltd. without further processing, for a major portion of the raw feed to a rotary kiln producing cement clinker. Oolitic aragonite is a high purity calcium carbonate material, dust free, with the appearance of a course, white sand. It is farmed when under the right conditions of temperature ocean currents, and ocean floor topography. The calcium carbonate will precipitate into small spherical particles on the ocean floor. These oceanic conditions are correct to cause precipitation of the calcium carbonate near Ocean Cay in the Bahama Island chain. The present growing deposit near Ocean Cay is in the billions of tons and is mined by a relatively shallow-operation hydraulic dredge. The aragonite thus formed is en orthorhombic crystaline form of calcium carbonate with a specific gravity of approximately 2.9. At a temperature of 505°C. (940F), the aragonite converts to the hexagonal crystal of calcite with a specific gravity of 2.6 to 2.7. This change in specific gravity weakens the structure of the particles but the individual pieces are still fairly hard. When the material is then calcined at 900°C (1650°F), the particles retain their shape but become soft and will break up under finger pressure.

Jan 1, 1978

By D. H. Y. Tang

3-dimensional finite element modeling was performed to analyze the safety factors of stump pillars, 18 ft. x 18 ft., under a cover of 208 ft. using the Modified Drucker-Prager Theory. The results showed that they are safe. This was substantiated by underground observations. But the safety factors predicted by three commonly used pillar design formulae showed otherwise. This paper discusses the modeling details and anlyze the difference between 3-D FEM method and traditional pillar design formulae.

Jan 1, 1987

By Ziyan Ouyang, Haotian Zheng, Spencer Quiel, Mike Mooney, Clay Naito

This paper summarizes the results of an experimental program conducted to characterize the moment-rotation behavior of skewed flat radial joints from large diameter (45 ft) tunnel lining. Both positive and negative joint moment-rotation behaviors were measured experimentally using two-segment joint combination assemblies. The results are compared to closed form methodologies used by designers, e.g., the Janssen method. The differences in observed and model behavior are discussed within the context of design practice.

Jun 23, 2024

By Jun Yuan

Kaolin clays from five different commercial deposits in Georgia were studied to understand the variations of zeta potential and related fundamental properties. The results suggest that higher negative zeta potential is related to exchangeable or soluble calcium ions in the clays.

Jan 1, 1997

By N. Duru

"Gravity concentration is still a challenging area in the mineral industry. This is mainly because of the fine size valuable mineral losses to the tailings during its application. But the recent developments in centrifugal separation methods and their mutual application with conventional separation techniques has increased mineral recoveries. In this paper, field application of conventional gravity separation methods with the combination of 2” diameter hydrocyclone cluster unit and a multi gravity separator (MGS) was discussed. Additionally, particle size distribution and chromite content of the plant streams is presented and initial laboratory test results were compared with the actual plant data throughout the paper. As expected, field data showed derivations from the laboratory tests but the combination of MGS and conventional gravity separation techniques resulted in gravity separation of -0.1 mm chromite particles. INTRODUCTION The purpose of this mineral processing plant project was to investigate the possibility of upgrading chromite ore from 12% to 48% Cr2O3 and having final tailings assay as 2% Cr2O3. For this reason, initially a set of laboratory gravity separation studies were conducted to evaluate the performance of combination of 2” diameter hydrocyclone cluster and multigravity separator. After obtaining successful results from the laboratory work, a feasibility study was initiated. Economical results of the feasibility study showed that an achievable high net present and return on investment values. Following the investment decision; engineering, equipment procurement, construction of the processing plant was completed in eighteen months. This paper focuses on the initial laboratory test work results, operational data of the 2” diameter hydrocyclones and MGS units; resulted chromite recoveries. Processed ore has the chromite associated with serpentine and olivine minerals. The chromite particles are generally in round shapes with sizes between 50 µm to 1600 µm and average size of 450 µm. The microscope images of the chromite and associated formations are presented on Figure 1.Chromite is formed in mixture with iron oxides, with varying amounts of magnesium, aluminum. The average chemical composition of the representative drill core samples of the ore deposit is given on Table 1."

Jan 1, 2017

By J. F. Oyler

One of the most important applications of material handling engineering technology occurs in iron ore pelletizing plants. Although the total installed value of material handling systems in such plants, as well as in many other modern process plants, is a relatively small percentage of the value of the plants (5 to 10% perhaps), their significance is considerable. Indeed this significance equals that of the more expensive process equipment in the plant, since the failure of any component of any system causes, shutdown of the entire plant. It is because of this increased consequence of failure that design criteria for process plants are more conservative than for conventional material handling applications. A second unique characteristic of material handling technology applied to process plants in general is the variety of materials being handled and the wide range of problems this variety presents. One extreme encountered is the stickiness of filter cake. Here the entire design effort is aimed at keeping the material flowing through transfer points and preventing it from building up on components. Another extreme is the conveying of fired pellets - hard spheres with a very flat angle of repose and abrasive characteristics severe enough to make conventional wear plate materials impractical.

Jan 1, 1976

By Douglas B. Silver

"Editor’s note: Douglas B. Silver, Portfolio Manager, Orion Resource Partners, was the keynote speaker at the 2017 SME Annual Conference & Expo in Denver, CO on Feb. 19, 2017. He also gave the keynote address to the SME Annual Conference in 2008. The following is his 2017 keynote address with a few of the slides that were presented. The full speech is available on YouTube https://www.youtube. com/watch?v=uF0qwGJIX3UIn 2008, I had the privilege of giving SME’s keynote address. At that time the financial markets were on the verge of collapse and my presentation described the issues. Unfortunately I was correct, and global markets went into a steep nosedive, creating the largest economic downturn since the Great Depression.In hindsight, there were plenty of signs that this was coming. The Supercycle had created massive new wealth. This wealth was largely invested in the United States due to the country’s political stability and credit worthiness. In 2004, the large investment banks convinced the U.S. Securities Exchange Commission (SEC) to allow them to triple their borrowing leverage ratios. This made the banks more vulnerable to market volatility. The banks then lent money to NINJAS - people with no income, no job and no assets. Even worse was the fact that these unqualified home owners used adjusted-rate mortgages (ARMs) which they, of course, intended to refinance prior to interest rates rising. These mortgages were then bundled up by the banks and sold to investors as “safe” investment products. The money flowed into these products because the rating agencies gave these instruments high marks. These same agencies earned their fees from the very same banks seeking high ratings. (No conflict there). Private debt exploded and peaked out in 2008.These mortgage products were sold in an unregulated shadow banking system and the ARMs came due. Toxic mortgage default rates skyrocketed and the mortgage-backed securities collapsed in value. This house of cards had a negative feedback loop that accelerated the market crash and resulted in more than $1.5 trillion being lost in the securitization sector, a 47 percent decline in the Dow Jones Industrial Average, foreclosure rates skyrocketing and housing prices collapsing. The financial markets were in a nosedive."

Jan 8, 2017

By C. D. Keith

Erie Mining Company, a pioneer in the iron ore pelletizing industry, has continued to develop methods and equipment to improve cost and quality. Under the management of Pickands Mather & Co., this property, owned by Bethlehem Steel Corporation, Youngstown Sheet and Tube Company, Steel Company of Canada, Ltd., and Interlake, Inc., has initiated a number of operating improvements for the taconite industry. One of the most noteworthy of these, which is applicable to the entire mineral industry, is the principle of fine screening with rappers (FSR). Erie's original efforts in the field of fine screening, which date back to 1961, were described in the April 1967 issue of the MINING ENGINEERING magazine. In that same month, Erie placed into operation a full scale PSR and regrind plant addition, capable of processing 10.3 million long tons of iron ore concentrates, produced by conventional taconite grinding, classification, and magnetic separation methods. Since this first successful commercial operation of the PSR principle et Erie, it has been applied in eight other iron ore beneficiation plants end is being tested by other U.S. and foreign companies. In addition to the use of PSR units at Erie Mining Company, Pickands Mather has applied PSR to other of its managed properties end to projects under development. This paper covers these applications as well as a now application at Erie Mining Company.

Jan 1, 1971

By Wenbing Guo, Gaobo Zhao, Erhu Bai, Brijes Mishra

"Violent damage to overlying strata can occur above the large mined-out space left by high-intensity longwall mining. For the safe mining under the aquifer and surface water body, it is imperative to investigate the criteria of overburden failure degree due to high-intensity mining. In this paper we present the characteristics of high-intensity longwall mining panels and overburden critical failure. Based on the geological and mining conditions of a high-intensity mining panel, 3D numerical models that consider the maximum horizontal principal stress and minimum horizontal stress and their orientations with the panel advance direction were established by using the 3DEC software. Sizes of the panel reaching the critical failure of the overburden under different mining thicknesses (3.5 m, 6.5 m, 9.5 m, 12.5 m, and 15.5 m) were analyzed. Further, criteria of overburden critical failure were proposed for the high-intensity mining. The coefficient of overburden critical failure (Cf) is the ratio of the strike length (Ls) to the mining depth (H). Through curve fitting analysis, a fitting equation between Cf and mining thickness was obtained. The results showed that overburden failure criterion with high-intensity mining panel is 0.38 = Cf = 0.97 with different thicknesses. Field measurements validated the results from the numerical models.INTRODUCTIONHigh-intensity longwall mining refers to a coal mining method with thick coal seam, large panel width, fast face advance rate, and severe damage to the overburden and surface in China (Guo et al., 2018). Violent movement of the roof rock and severe damage to overlying rock strata occur in the large mined-out space left by a high-intensity longwall mining panel, which is a 3D (three-dimensional) structure layout with highly non-uniform stress distribution. Recognition of such fact a will facilitate this overlying rock strata failure problem investigation (Peng et al., 2019).The studies of overlying strata failure due to longwall coal mining have been reported by some scholars with different methods. Kang et al. (2018) studied the sudden massive roof collapse during longwall coal retreat mining by a large-scale two-dimensional physical model and a UDEC numerical model. Ghabraie et al. (2015) researched the mining-related strata movement by applying the three-dimensional laser scanner, optical transducer, and digital image processing techniques to two-dimensional physical models. Wang et al. (2015) analyzed the structural characteristics and fracture failure process of overlying hard and thick main roof by a 3DEC numerical model; this study also investigated the geostress reduction and permeability enhancement redistribution of the adjacent coal measure strata by FLAC3D. Guo et al. (2012) performed a three-dimensional finite element analysis and shared some insights into the dynamic interaction between mining induced strata stress changes, failures, and gas flow patterns. Meng, Shi, and Li (2016) proposed a 3D coupling model between stress and permeability, investigating the dynamics of a stress, permeability coefficient using FLAC3D. Khanal, Guo, and Adhikary (2019) used the 3D numerical modelling approach (COSFOW) to investigate the strata deformation and the change in permeability in the overburden strata due to the underground extraction. However, few studies considered the influence of the horizontal stress on overburden failure in a high-intensity longwall mining panel, and the critical failure criteria of overlying rock strata is unclear."

Jan 1, 2019

By Yuexin Han, Mu. Yufan, Yanjun Li, Peng Gao, Yongsheng Sun

"The objective of this study was to evaluate the effect of reduction temperature, reduction time and binary basicity on the size of metallic iron particles in coal-based reduction products of an oolitic iron ore. The particle size distribution behavior (i.e., cumulative passing percentage and mean size of metallic iron particles) during reduction was investigated in detail. Results showed that the particle size distribution of metallic iron particles was strongly influenced by reduction temperature, reduction time and binary basicity. The cumulative passing percentage and mean size significantly increased with reduction temperature and time in the entire range of the experiments. All curves of cumulative passing percentage versus particle size under different conditions demonstrated a similar trend (continuous increase). The size distribution parameters and mean size slightly increased with increasing binary basicity and significantly decreased when the binary basicity exceeded 1.0. The size of metallic iron particles could be controlled by adjusting the reduction conditions during coal-based reduction.IntroductionThe increasing demand for iron ore coupled with diminishing high-grade iron ore reserves has resulted in the urgent need for innovative technologies in order to use refractory iron ores. Oolitic iron ore is a typical refractory iron ore with tremendous abundance globally. Based on published literature, oolitic iron ore reserves are approximately 140 million tons in Europe, 10 billion tons in China and 66 million tons in Pakistan (Kazmi and Abbas, 2001; Wu et al., 2011; Yu and Qi, 2011; Sun et al., 2013a). Therefore, the efficient exploration and use of oolitic iron ore resources can play a significant role in easing the mineral resource crisis in the iron and steel industry. However, oolitic iron ore cannot be effectively upgraded by traditional beneficiation methods due to its mineralogical characteristics (e.g., low grade of iron, poor liberation of iron minerals and high phosphorus content) (Li et al., 2011b; Sun et al., 2013b).Researchers recently proposed coal-based reduction followed by magnetic separation to recover iron from refractory iron ores (especially oolitic iron ore) and a certain degree of breakthrough was achieved in both theory and practice. In this technology, iron minerals in the ore are directly reduced by coal to metallic iron, which grows into particles of different sizes. After comminution and liberation, metallic iron is concentrated by magnetic separation (Srivastava and Kawatra, 2009; Sun et al., 2013a; Li et al., 2011b; Sun et al., 2013b; Li et al., 2011c; Gao et al., 2013). Sun et al. and Gao et al. used this technology to examine the recovery of iron from oolitic and Bayan Obo iron ores, respectively (Sun et al., 2013a; Li et al., 2011b; Li et al., 2011c). Metallic iron powder with more than 90% iron content was obtained as the final product, which could be used directly in steel production."

Jan 1, 2015

By S. V. Krishnan

In the upgrading of finely-disseminated iron ores, selective desliming is the critical step which must be controlled in order to achieve efficient flotation. A prerequisite for selective desliming is a properly-dispersed pulp; sodium silicate is commonly used as a dispersant. The mechanism by which sodium silicate acts as a dispersant in the presence of calcium ions was examined by streaming potential measurements, settling tests, abstraction density determinations, selective flocculation tests and scanning electron microscope observations. The study established that calcium silicate precipitates on the mineral surfaces dispersed the pulp. Although sodium silicate was a nonselective dispersant, the addition of corn starch aided the flocculation of goethite over quartz at low silicate additions, but became ineffective at higher silicate levels. A model is presented to explain the dispersant mechanism of sodium silicate in the presence of calcium ion for selective flocculation of iron ores.

Jan 1, 1982

By Rodney L. Stone

As part of an overall laboratory and plant test program to determine mixing and other techniques relating to the more economic use of bentonite as an iron ore pellet binder, a settling test was developed for measuring the bentonite content within a pellet or within a batch of pellets. Between pellet batches, each containing a different level of bentonite, the dry fracture load is directly proportional to the bentonite content between pellets of the same batch, however, the fracture load is inversely proportional to the bentonite level; this is explained by a negative correlation between a pellet's size and its bentonite content and the fact that larger pellets can withstand a higher fracture load than the smaller.

Jan 1, 1968

By E. B. Kroeger

Spoil instability has been a problem at a coal mine in interior Alaska. Parameters such as original site topography, groundwater conditions, material properties, spoil-pile geometry, geology, permafrost, natural slope instability, changing weather conditions, and dense, near-surface vegetation have interacted to produce unstable slopes. Several failure modes have been identified including deep seated earth block slides, bimodal earth flows, and solifluction. Thawing of permafrost also created conditions where sliding of spoil along the interface separating the spoil and the natural ground surface occurred when the cohesion and the friction angle of that zone was reduced to zero and below 15?respectively.

Jan 1, 1992

By John P. Cummings

Glass is the most unique substance which man has made. It is understood that Phoenician sailors playing on the beach in Mesopotanmia around 12000 BC, produced glass by the fusion of sand and soda in their campfire. Glass is unique for many reasons. However, let us consider the following. It is made of materials which are opaque and yet glass can be translucent, transparent, or opaque. It can be as soft as cotton or stronger than steel. It transmits light readily and yet is totally impervious to gases and liquids. It is chemically an inert, creates very little pollution in its manufacture. It is made of the most abundant raw materials on earth. It is readily recyclable and has little pollution in its disposal. Glass containers are made principally from sand (that is, silica), soda, which is sodium carbonate, and lime, which is calcium carbonate, plus decolorizers or colorants and cullet. The proportion of cullet, broken glass, in most glass tanks today is roughly 10 to 20% of the glass product. In most cases, the cullet used in the plant is glass from off-ware, or broken ware, which is a waste product within the plant. Cullet has the following advantages. It contains all of the raw materials normally used in a batch. It tends to melt at a lower temperature than batch, thus saving some fuel, and, finally, by forming a crust above the normal melting system, there is a tendency to cut down air pollution.

Jan 1, 1975

By B. H. Kim, P. Zhang, M. A. Van Dyke, D. Su, H. Dougherty

The National Institute for Occupational Safety and Health (NIOSH) has been evaluating longwall mining-induced strata fractures and their impacts on casing stability of Marcellus shale gas wells located in longwall pillars. To understand the extent of overburden fractures after longwall mining, NIOSH researchers drilled a postmining corehole into the fractured strata above the Pittsburgh coal seam longwall gob. Knowing the extent of the fracture zone height will help gas operators minimize the hazards of drilling into longwall gobs. The core was retrieved from the surface down to the top of the gob void. Various fractures were encountered varying from 35 to 64 degrees, depending on lithologic type and relative closeness to the gob. The longwall panel dimension was 457 m wide and 3657 m long, in which the total fracture zone height was found to be at 141 m and the hydraulic connected fracture zone at 87.7 m above the top of the Pittsburgh seam. In addition to core drilling through the gob, FLAC3D modeling was also used to simulate the formation of fracture zone and the orientations of longwall-induced fractures. This study provides much-needed evidence on the fracture zone of Pittsburgh seam longwall gobs to help gas operators avoid potential hazards associated with drilling through highly fractured zones

Mar 2, 2022

By P. Zhang, D. W. H. Su, M. Van Dyke, H. Dougherty

To provide critical scientific data and engineering guidelines to federal and state regulatory agencies as well as the coal and gas industries, the National Institute for Occupational Safety and Health (NIOSH) initiated a Gas Well Stability Research Program in 2016. This paper summarizes the critical scientific data acquisition, interpretation, and modeling by NIOSH regarding the stability of unconventional shale gas wells influenced by longwall mining. Currently, NIOSH is the only organization in the U.S. conducting such fundamental and impactoriented research, which receives input and collaborations from MSHA, PADEP, WVDMS, OHDNR, the coal industry, and the gas industry. Results from the NIOSH field instrumentation programs—which include surface, subsurface, and underground instrumentation—and the parallel three-dimensional numerical modeling programs indicate that, under shallow and medium covers, the measured horizontal displacements within the abutment pillar are one order of magnitude higher than those measured under deep cover. Casing couplers are found to play an important role in longwall-induced casing deformations. Cementing alternatives are found to have significant impact on longwall-induced casing stresses and deformations. Measured 60-arm caliper logging results are in good agreement with three-dimensional computer simulation results. Engineering guidelines on longwall-induced deformations, casing and cementing alternatives, gas well setback distances, as well as risk assessment strategy are proposed.

Mar 2, 2022

By M. P. Fahey

A significant amount of silca is recovered in the rougher stage of anionic flotation of Florida apatite. This recovery, in the past, has been attributed to both entrainment and cation activated flotation. This study shows that by using a transport factor, it is possible to determine the contribution of each mechanism towards silica recovery. Further, it is shown that the concentration of cations in the conditioning water significantly affects both the amount of silica recovered due to entrainment and true flotation. Further confirmation of this phenomenon was obtained by Ca++ doping of the conditioning water and by using a sodium silicate depressant.

Jan 1, 1996