Search Documents

By Venkata S. Vutukuri

Assuming a number of discrete leakage paths and treating the airflow through leaky duct line as a series-parallel combination of airflows along the duct and through leakage paths, exact solutions for auxiliary ventilation problems can be obtained. A computer program "SEGMENT'' has been written to solve problems using this method. However, most of the investigators have treated the duct lines with a uniformly distributed leakage and many have derived formulas assuming various boundary conditions and levels of simplification for the design of a simple auxiliary ventilation system An appraisal of accuracy of the various formulas has been conducted using the results from the program "SEGMENT' as benchmark and the formulas which give accurate results have been identified. The ranges of application for all the formulas have also been determined for 5 %error.

Jan 1, 1993

By William H. Langer

Nearly every community in the United States is dependent on aggregate (sand, gravel, and crushed stone) resources to build and maintain its infrastructure. Unfortunately, developing aggregate resources to meet societal needs causes environmental impacts. Most environmental impacts associated with aggregate mining are benign. Extracting aggregate seldom produces acid mine drainage or other toxic effects commonly associated with mining of metallic or energy resources. The most obvious environmental impact of aggregate mining is the conversion of land use, most likely from undeveloped or agricultural land use, to a hole in the ground. This major impact is accompanied by loss of habitat, noise, dust, blasting effects, erosion, sedimentation, and changes to the visual scene. Some of the impacts are short-lived, and most are easy to predict and easy to observe. Most impacts can be controlled, mitigated, or kept at tolerable levels and can be restricted to the immediate vicinity of the aggregate operation by employing responsible operating practices and available technology. The intensity of environmental impacts generated as a result of mining are determined in large part by the geologic characteristics of aggregate deposits (geomorphology, geometry, and physical and chemical properties). Mining deposits that are too thin, or contain too much unsuitable material, results in the generation of excessively large mined areas and large amounts of waste material. Mining aggregate can lead to serious environmental impacts in some situations. Some geologic environments such as active stream channels, slide-prone areas, and karst terrain are dynamic and respond rapidly to outside stimuli including aggregate mining. Some geomorphic areas and (or) ecosystems underlain with aggregate serve as habitat for rare or endangered species. Similarly, some geomorphic features are themselves rare examples of geologic phenomena or processes. Mining aggregate might be acceptable in some of these areas, but should be conducted only after careful consideration, and then only with extreme prudence. Failure to do so can lead to serious, long-lasting, and irreversible environmental consequences, either in the vicinity of the site or at locations distant from the site. Environmental impacts caused by irresponsible aggregate mining can compromise mining in an entire region.

Jan 1, 2001

By Patrick A. Ley

Maintaining, managing and manipulating large quantities of geologic data can be a very costly and time-consuming process. The use of computer-based methods can provide some relief to the problems of editing, displaying, and interpreting spatial geological data. ENCORE is a system designed specifically for coal orebody modeling and reserve esitmation where the geologic data is stored on a large mainframe computer and is accessed from a local work station for editing, manipulating, and producing various reports and high-quality engineering maps. The ENCORE system was designed for use by the geologist or mining engineer with little or no computer background and, additionally, it was designed to provide the geologist or mining engineer enough flexibility to be able to select the appropriate methodology for the orebody being analyzed. The various analysis tools incorporated into ENCORE can significantly increase the professional's productivity without burdening he or she with the need to understand the details of the internal computer language.

Jan 1, 1982

By F. Romero, L. Yacher, M. Orchard

Specific software tools for Statistical Multivariate Analysis combined with real time process data were applied to Concentrator Plant at Compañía Minera Doña Inés de Collahuasi SCM in Chile, basically to two Mill Lines, each one with one SAG mill (32’x15’8MW)and one Ball mill (22’x36’9.7MW). The main objective was to empower the operator actions using process patterns references instead of process variable set-points. Pattern clustering and the analysis of pattern deviations regarding normal or desired pattern, allows for improvements in process control and the further implementation of soft sensors for those variables not included in the initial model.

Jan 1, 2003

By S. W. Beckman, L. Williams, A. E. Seep, R. Fischer, J. Hubbard

Introduction The Summitville Mine located in southwestern Colorado was added to the National Priorities List in June of 1994. Summitville was the site of mining operations that began in 1873 with the discovery and development of gold placer and lode deposits in the late 1800's. The mine site is located about 25 miles south of Del Norte, Colorado in the San Juan Mountains adjacent to the Rio Grande National Forest at an approximate altitude of 11,600 feet. The site was mined for gold, silver and copper between 1873 and 1947. The Summitville Consolidated Mining Corporation, Inc. (SCMCI), a wholly-owned subsidiary of Galactic Resources, Ltd of Vancouver, Canada ran a large tonnage open-pit mine and cyanide heap leach operation from 1986 to 1992 (Pendleton and Posey, 1992) During the mine operation by SCMCI, approximately 10 million tons of gold ore was mined, crushed and stacked on a lined leach pad. Heap leach operations experienced water balance and unplanned solution discharges from the start of the mine life. Despite the production of 249,000 troy ounces of gold during the mine operation, SCMCI was unable to meet remedial requirements and notified the state of Colorado of its intention to file a Chapter VII bankruptcy in December 1992. The EPA Region VIII Emergency Response Branch took over site operations on December 16, 1992 to prevent a catastrophic release of hazardous substances to the environment. The multiple contamination sources at the mine site are due to both historic and SCMCI mining operations. Emergency response operations at the site have prevented releases of severely contaminated solution and a permanent treatment for all waste units at the site is under investigation. A Request for Proposal (RFP) was issued in October 1993 by Environmental Chemical Corporation (ECC) at the Request of EPA Region VIII, Department of the Interior and Bureau of Reclamation. The RFP requested that interested companies provide information on their ability to implement innovative treatment technologies to improve treatment efficiency and reduce treatment costs for remediation of the heap leach pad (HLP) spent ore and ore leachate solutions. Dames & Moore and Pintail Systems, Inc. (PSI) jointly submitted a proposal suggesting application of biotreatment processes for detoxification of cyanide in spent ore and HLP leachate solutions. The proposal was accepted for pilot and field demonstration under the SPA Superfund Innovative Technology Demonstration Program (SITE) with additional funding from EPA Region VIII. This report discusses the test program and results of a Focused Feasibility Study which demonstrated biotreatment processes for spent ore cyanide detoxification.

Jan 1, 1995

By S. J. R. Lowrie, J. S. Edwards, A. D. Jones

A small scale model has been constructed to simulate air and gas flows on a full scale retreat longwall coal face. Scaling relationships were derived to define how the main aerodynamic properties of the full scale could be preserved in the small scale model. These scaling requirements include: a minimum value for the Reynolds number for the flow on the face in order to maintain turbulent flow with a constant non-dimensionalised coefficient of turbulent dispersion; a constant Richardson number to maintain similitude for the formation of layers of buoyant gas; scaling of the permeability of the waste so as to obtain the same proportion of seepage flow through the waste; pressure gradients due to the ventilation and to the density difference (between the air and the gas layer) were kept in proportion; and in the waste, the relative contributions of inertial dispersion and molecular diffusion were approximately in proportion. The complementary roles of computational fluid dynamics (CFD) and aerodynamic scale models for simulating mine ventilation are discussed. The physical model is described and an example presented of simulations of the effect of changes in mining condition on the effectiveness of gas control in retreat longwall coal faces.

Jan 1, 1995

By R. M. Parlman

Interest is increasing in obtaining incremental improvements in mineral recoveries in flotation processes because of changing world economic conditions. Research on collector reagents, long indispensable components in flotation systems may provide the cheapest and simplest route to higher metal recoveries. Sulfhydryl group - containing compounds (-SH) and their salts, e.g., dithiophosphates, xanthates and a few other derivatives are commonly used to promote the flotation of sulfide minerals. Alkyl mercaptans, another class of sulfhydryl compounds, have long been known to have collecting properties but have been relegated to dormancy for one reason or another. This paper reports results from new investigations of alkyl mercaptans, trithiocarbonates, and a petroleum oil with a variety of western domestic and Canadian ores for copper and molybdenum sulfides recovery. Specific opportunities are pointed out to the industry for mineral recovery enhancement through the use of the proper reagent combination.

Jan 1, 1980

By Stanislaw Nawrat, Waclaw Dziurzynski

An increasing concentration of coal production, especially in the circumstances of intensive methane inflow makes the coal mine managing staff apply new techniques of safe mining. It paves also the way for scientists to develop new directions of investigations and implementation of state-of -the- art technical solutions. Simultaneously, it could be noticed that the funds assigned for expansive 'En situ ' investigation are continuously decreasing. Better and better results are reached when applying computer technique in calculations of the parameters of ventilation process. Recent theoretical and experimental investigations of air and gas (methane) flow in longwall areas with caving, combined with the implementation of methane drainage system allowed to create, a mathematical model and consequently to elaborate a computer supported numerical simulation of discussed phenomena. The mathematical model has been modified and the simulation program was prepared in such a way that the software is convenient for a user looking for an optimal solution. The paper presented the methodology of optimal choice of following parameters: - ventilation system - rate of flow through the wall. The procedure takes into consideration keeping a safe level of concentration methane in air flowing through the longwall as well as the criterion of maximum methane concentration within the methane drainage pipe line. Results of variant computer simulation regarding the longwall with caving are shown in graphs and tables.

Jan 1, 1995

By Joseph Keenan

In March of 1994, Dynatec Mining Limited entered into a contract with PCL Civil Constructors to carry out the underground excavations for the Algonquin Power Corporation’s15 Megawatt Nagagami hydro-electric power station located near Hearst, Ontario, Canada. Dynatec completed the work for this project in early October 1995. Dynatec Mining Limited’s work included the excavation of a 175 meter long penstock driven at a grade of -25% to a 4000 m3 powerhouse located 50 meters below the intake elevation. A 1200 meter long tailrace was driven from the Nagagami River to connect with the powerhouse. Two 50 meter raises were driven from the powerhouse to surface to pro-vide access for equipment and personnel. The excavation of the tailrace tunnel(5.8m x 5.9m) was completed using Dynatec’s Long Round Jumbo Technology.

Jan 1, 1997

By M. Saidman, R. Pizzuti, R. Hirschfeld, A. J. Desai, J. Rand

Two bedrock tunnels, 170 to 250 feet deep and with a length of about 17,000 feet each, will be used to convey cooling water from the Atlantic Ocean to the Seabrook, N.H., Nuclear Power Plant. Seismic reflection and refraction surveys were used to obtain preliminary information about overburden and bedrock conditions. A major boring program, including core orientation and water-pressure testing, was undertaken to provide detailed geologic data. The results of the geotechnical investigation were summarized in terms of rock type, frequency and character of joints, degree of weathering, modified core recovery (RQD), pressure-test results and strength and hardness. These parameters were used as a basis for evaluating the feasibility of using a tunnel-boring machine, for designing and estimating the initial support systems, and for evaluating the grouting and tunnel lining requirements.

Jan 1, 1976

By L. Shevenell

Nevada now has, or will have, 35 pit lakes resulting from open-pit mining below the water table. State regulators are requiring that the ultimate pit lake water quality be predicted as part of the permit application process. Water balances/pit lake filling rates must be esti¬mated in support of the geochemical modeling. In Nevada, analytical and numerical methods have been employed for the study of pit lakes. In the current work, analytical solutions are investigated for one pit lake, the Getchell south pit lake, which previously filled be¬tween 1968 and 1982 during a hiatus in mining. Water levels vs. time are available for this lake and these data have been fitted with a hyperbolic curve. This water-level-vs.-time curve was used in simple water-balance computations to find the net inflow rates by forcing computed water levels and volumes to match those of the known water levels and volumes through time. The model described here provides realistic volume fluxes into and out of the lake on a monthly basis as the pit lake filled.

Jan 1, 2000

By Jack W. Eloranta, Michael J. T. Orobona, Peter R. VanDelinder

Ore blending for process optimization is becoming an increasing factor for managing cost and productivity. Economic mining and processing a very low value ore in an extremely competitive market results in constant cost-cummng initiatives. The inherent conflict between the lowest possible mining cost and the lowest possible milling cost is reviewed here in the context of blasting for autogenous mills. Iron ore blending focuses on a number of properties-liberation values, weight recovery and concentrate silica being the most important. Other chemical and metallurgical factors are also commonly controlled. Recent research has fueled an emerging interest in blending on physical ore properties as well. Fully autogenous mills rely on the large, competent fraction of crushed feed to act as grinding media. Previous test work indicated that Hibtac mills require specific amounts of 6- to 10-inch ore. High recirculating loads require a steady influx of large rock fragments. Blast designs, therefore, are presently characterized by wide patterns and low powder factors. Current efforts are aimed at improving mill throughput while reducing overall energy costs. Based on research and published case studies and the advent of optical measuring devices, Hibbing Taconite Company has embarked on a blast optimization program to identify optimum mill feed and to design blast fragmentation goals for each geological unit and each mining area. This paper outlines the preliminary findings of an ongoing, broad-based team effort which requires close cooperation of geologists, mine engineers, crushing and milling personnel. Three specific areas of investigation are reviewed: I) Historical relationships between powder factor and mill performance, 2) Blast fragmentation modeling using the Kuz-Ram model, and 3) Drill

Jan 1, 2004

By Egon Pohl, Friedrich Steinhäusler, Werner Hofmann

INTRODUCTION Anticipated increase of nuclear fuel production in the future coincides with growing concern about the occupational health risk of miners from inhaled radon decay products. As a consequence it has been suggested to even lower presently permitted exposure levels (NIOSH, 1980) and implement more stringent control on measurement programmes. Compliance with these regulations requires large investments in new or modified ventilation systems as well as in increased expenditure for staff and instrumentation for health physics operational monitoring. Since both costs are directly related to the overall ore production costs, this can have far reaching implications with regards to the economic feasibility of certain mining operations and consequently reduce estimates of low-cost minable ore reserves. In addition there is increasing evidence that the radon problem is not limited to the nuclear fuel cycle only, but can also represent a significant hazard to non-uranium miners. A key component in the cost-effective implementation of legislative control measures is the monitoring system employed. The choice of system is decisive for the total costs of installation and maintenance, manpower requirements and accuracy of nuclide determination. In the following operational specifications are defined for monitors in mining and milling environments. Different types of available instrumentation are discussed with regard to their suitability for practical radiation protection in underground mines, open cut mines and mills. ATMOSPHERIC CHARACTERISTICS Underground mines Radon in the air of underground mining operations is exhaled from surrounding rock surfaces, crushed material and, to a lesser extent, from water seepage. Whilst in uranium mines radon releasing ore bodies are generally localized in distinct areas, radon sources in non-uranium mines can be very dispersed throughout the system of mine tunnels. The ventilation scheme used influences the absolute atmospheric level of radon as well as the equilibrium conditions between radon and its decay products (factor F). In uranium mines mechanical forced-air ventilation is normally the only way to achieve and maintain legally required nuclide levels. This causes the F-factor to be rather low, e.g. in French CFA-mines F is of the order of 0.2 (Francois, Pradel, Zettwoog, 1975). At the same time the fraction of unattached radon decay products (fp) can increase due to the high air velocities employed. However, it is possible to find non-uranium mines with either natural draught ventilation only or assisted on demand by forced air ventilation during special operations or climatic conditions. Thereby the F-factor is more dependent on seasonal changes of temperature differences between outdoors and mine atmosphere and work routines. As a result F can cover a wide range from 0.02 to 0.95 (Steinhäusler, 1976). The use of filters or electro-precipitators in mine ventilation systems can modify the atmospheric characteristics twofold as it generally decreases the content of radon decay products, but at the same time increases the content of the unattached fraction fp . Average concentration levels of radon decay products are mostly lower in mechanically ventilated non-uranium mines than in equally ventilated uranium mines and are below 0.3 Working Level (UNSCEAR, 1977). However, some working places in non-uranium mines, specially with only natural draught ventilation can occassionally approach maximum permissible levels as defined for uranium mines (Strong, Laidlaw, O&apos;Riordan, 1975; Snihs, 1976; Sciocchetti, Scacco, Clemente, 1981). Open pit- and surface mines Radionuclide levels of radon decay products in the atmosphere of these mines are mostly too low to represent a significant inhalation hazard for miners, ranging typically from 0.03 to 0.1 Working Level (Steinhäusler, 1976). However, personnel using airpurifying respirators or working in cabins ventilated with filtered air can be exposed to a radon atmosphere with low value for the F-factor (F [<] 0.1) and high fp-value up to 80 % (Leach and Lokan, 1979). Mills Atmospheric radon concentration in crushing, grinding, drying and packing sections depends on the radium 226 content of the ore, ore storage methods and ventilation system employed. Providing adequate ventilation ([>] 2 air changes per hour) and control of dust production radon and its decay products represent only a minor problem (Saconney, 1979). MONITORING OF OCCUPATIONAL EXPOSURE Objectives Operational monitoring of the working places provides information on: - confirmation of appropriate control of the routine mining methods employed - indication of abnormal conditions. Although this type of monitoring enables the location

Jan 1, 1981

By Larry Whittle

Gold milling activities generate waste streams containing dissolved metals and cyanide, among other contaminants, that require some form of treatment prior to discharging to the environment. To date, this treatment has involved the destruction of cyanide through natural degradation, chemical oxidation, or a combination of both followed by the precipitation of metal hydroxides. Although these processes have been proven to be capable of achieving. regulatory levels for metals and cyanide, they often generate significant levels of cyanate and, at times, ammonia, that may be toxic to rainbow trout and thus undesirable for regulatory compliance. Tallon Metal Technologies Inc. (Tallon) has developed Vitrokele™, a chelating resin that has the ability to capture metals (including gold), both total and weak acid dissociable cyanide, as well as thiocyanate from both slurries and solutions. The loaded resin is eluted and returned to the recovery circuit while metals and cyanide are recovered from the eluent stream. This process was demonstrated at pilot scale at B.P. Resources' Hope Brook Gold Mine in Newfoundland, and more recently at Canamax's Bell Creek Mine near Timmins, Ontario. The results from these pilot programs showed metal and cyanide recoveries of 99% or more with the concentration of cyanide and metals in the effluent reduced to levels with minimal or no toxicity to rainbow trout. Furthermore, neither cyanate nor ammonia were generated from the process. The loaded resin was effectively stripped and re-introduced to the recovery circuit; cyanide was captured in the eluent stream and made available for recycling to the mill leaching circuit; and metals were captured for re-use, sale or disposal. This paper summarizes the results obtained from the pilot tests at the Bell Creek and Hope Brook Gold mine sites.

Jan 1, 1992

By R. M. White

Abstract. Gulf Coast Salt Domes are being considered for radioactive waste disposal and this paper describes the geophysical techniques currently being used and those being considered for later phases of the program. Detailed gravity work utilizing a modification of the Talwani-Ewing modeling technique, shallow high resolution reflection seismic surveys using the mini-sosie concept, surface electrical resistivity and down-hole geophysical logging to add a third dimension to all of the surface techniques and to allow inverse modeling of the surface data sets are being utilized. The logic of the combined geophysical surveys will be discussed as well as their relative economics and their relationship to the overall exploration effort.

Jan 1, 1980

By Tim Neil, O&apos

The coming years should see moderate growth in the US coal industry. That growth may come at the expense of the oil and natural gas industries. Conoco pegs coal growth at 2% a year, until the year 2000. During that same period, Conoco projects only 0.5% annual oil growth and "a flat or negative trendline" for natural gas. This is compounded by the fact that coal has a delivered cost per Btu that is only half as much as it is for natural gas and only a third as much as it is for oil. So said Ralph Bailey to many of the 2600 attending the opening session of the American Mining Congress Coal Convention, May 12-15, in Pittsburgh, PA. Bailey is chairman of the AMC. He is also chairman of Conoco. While coal&apos;s projected growth is not spectacular, "it is in fact almost an assured growth," Bailey said. Weak oil and gas prices will likely prevent faster growth for US coal. Most of coal&apos;s increased demand will come from the electric utility industry and expanded steam coal exports. Conoco&apos;s study projects that domestic coal demand will be strengthened in the 1990s. By then, the present surge of nuclear power plant constuction will be over. And there will be a lack of acceptably priced, large-scale generation alternatives for utilities. "It is not likely that any electric utility is going to be ordering new nuclear reactors," Bailey said. "And as oil and gas supplies become scarcer and more costly, it is only logical that coal is going to fill the gap." At the same time, Bailey believes the US coal industry must find ways to lower its costs. He said cost excesses can be found in "regulatory overkill, labor, and simply bad habits" hidden by years of high inflation. "Those costs have now been laid bare, because we are going through a pe¬riod of disinflation. We have to put our house in order, particularly if we are going to compete in world markets." Bailey also touched on coal research. "The industry certainly accepts the fact that we must find a way to burn coal as cleanly as possible. A lot of work in that regard is going on. I expect there will be some significant break-throughs." Bailey said the coal industry is being squeezed this year. Last year, coal customers accumulated inventories in anticipation of a major coal strike that never materialized. Now, many utility customers are working down these inventories. So they are not taking deliveries on their coal contracts. But coal use is up in 1985, compared with 1984, Bailey said. So increased coal use, along with supply drawdown, should strengthen the coal market before the year is out, he said. After Bailey&apos;s presentation, some 100 speakers addressed policy and technical topics at 15 sessions during the four-day meeting. It was the first time since 1977 that the AMC Coal Convention has been held in Pittsburgh. And this year&apos;s attendance was up 40% from the last AMC Coal Convention held two years ago in St. Louis, MO. This year&apos;s registrants included 228 companies, 225 manufacturers, and 106 associated members. The only negative was the David Lawrence Convention Center. It was less than ideal. By turns, meeting rooms were too small, too cramped, or too far from one another. The session on longwall mining was so crowded that the doors were propped open so conference delegates could peer in. A concurrent manufacturers&apos; forum session needed 50 more chairs to accommodate those wanting to attend. However, on to summaries of some of the presentations. Coal transportation and export Since Congress approved the 1980 Staggers Rail Act, railroad rates for hauling coal have not been excessive. In fact, rail rates for coal have increased less than 0.5% a year, in real terms, since 1980. Moreover, the market oriented principles written into Staggers are contributing to the improved financial and operational health of the nation&apos;s railroads. But no railroad is earning excessive profits. That is the gist of a coal transportation study being completed by the US Department of Energy. William Vaughan is DOE&apos;s assistant secretary for fossil energy. He affirmed the thrust of the upcoming report. Vaughan did allow that Interstate Commerce Commission (ICC) regulations on rate reasonableness could permit the railroads to exploit their monopoly power on captive shippers. Luncheon comments later made by Don Hodel confirmed Vaughan&apos;s comments on railroad rate justification. Hodel is Secretary of the

Jan 7, 1985

By Stephen LaBrooy, David Muir

Gold ores in the geologically more recent rocks are often associated with copper minerals which pose problems of high reagent consumption with conventional cyanidation practice. Many examples exist in northern Australia, Indonesia, Papua­New Guinea, Chile, and Brazil where, despite various treatment options (LaBrooy, 1992), the processing of oxide and transition ores is uneconomic either for copper or gold recovery. Hence, there is a need for a reagent which is selective for gold without leaching copper minerals. The ammonia-cyanide system appears to meet this criterion (Muir et al, 1989; LaBrooy et al, 1991; Costello et al, 1992; Hayes and Corrans, 1992) but it has proven difficult to optimise and apply to a variety of ores due to differences in the mineralogy and reactivity of ores and a lack of understanding of how the system works. Recent work on the mechanism, however, (Muir et al, 1993) has thrown a new light on the problem which should allow better process control. Ammonia­cyanide mixtures behave neither like free cyanide nor free ammonia and too much of either reagent in the mixture is detrimental. The key to the process is understanding how ammonia enhances gold extraction yet inhibits copper extraction in an essentially cyanide environment.

Jan 1, 1993

By K. M. Kim

An analysis was conducted to determine the effects of blasting on slope stability and downstream comminution processes. To investigate these effects, the extent of blast-induced rock damage and the magnitude of induced stress were examined. This analysis showed that damage may extend up to 500 m (1 MPa, tensile strength) into the rock mass, a distance that is sufficient to have an impact on the pitscale slope over the long term. In addition, the damage zone was calculated using the assumption that compressive waves are the primary agent in microfracturing during blast fragmentation. The calculated damage zone — up to 2.2 m (43 MPa, rock mass compressive strength) — indicates that microfracturing can occur throughout 20-50% of the entire rock mass in the blasting area, depending on the blast geometry, burden and spacing. Finally, an economic analysis was conducted by comparing two assumed blasts in a copper mine. The change in energy required for crushing and grinding was demonstrated using Bond’s law after increasing the blast energy from 180 kcal/t to 350 kcal/t. A total cost saving of 13.3% ($9.4M) was achieved with the increase. However, the benefits of blast-induced microfracturing must be balanced against the potential impacts to slope stability to ensure safe conditions, a top priority in mining operations.

Jan 1, 2014

By R. J. Pugh

The coagulation of dispersions of weakly magnetic oxide mineral ultrafines (such as natural hematite or chromite) in an external magnetic field can be described from inter-particle forces. Essentially, coagulation occurs when the short range London-van der Waals interactions and the long range magnetic forces outweigh the stabilizing electrical double layer repulsion. From the classical colloid chemistry theory, we have calculated the various components of the potential energy for different sized particles at a series of ionic strengths and magnetic field intensities. We have related this theoretical analysis to experimental studies where the magnetic field-induced coagulation of ultrafines of natural hematite and chromite in aqueous suspensions was investigated using a laboratory scale electromagnetic solenoid. The experimental results relate the coagulation process (as determined by magneto-sedimentation analysis) to the particle size, the slurry pH and the external magnetic field. In the magnetic fields, maximum coagulation occurred near the pH of zero point of charge (pHzpc) of the minerals (where the electrostatic double layer repulsion was reduced to a minimum) enabling the particles to enter the "primary minimum" energy sink. On the other hand, in cases where the electrostatic repulsion was not suppressed, then the long range magnetic forces enabled coagulation to occur in the "secondary minimum". This caused the formation of chains which appeared to be relatively stable during sedimentation.

Jan 1, 1993

By M. Sears, G. S. Esterhuizen, Z. Khademian

According to the 2010-2019 Mine Safety and Health Administration (MSHA) accident report database, 91% of reported ground control accidents in U.S. longwall mines were caused by roof instability. Gateroads are subject to significant changes in loading conditions from the development to the longwall abutment loading phases. When combined with thinly bedded shale roof, found in many U.S. longwall coal mines, the design of efficient roof support becomes challenging. In previous work, the Bonded Block Method (BBM) modeling of roof by UDEC was validated against field extensometer measurements in a longwall gateroad entry roof at a 180-m depth of cover. The BBM was shown as capable of capturing delamination and buckling of shale roof, one of the main roof instability mechanisms in longwall mines. This paper presents the recent findings on the roof-support interaction using BBM models of the same longwall entry. The effects of cable bolts, roof bolt density, and strap support on potential roof instability are studied. These types of studies are difficult and costly to conduct in an operating mine. Results show how the contribution of bolts, straps, and cable bolts can be quantified using the BBM models. The study demonstrates the potential for BBM numerical models to help understand the complex roof and support system interactions and to assist with optimizing gateroad support systems.

Feb 1, 2023