Search Documents

By Richard W. Patton

With the advent of the Clean Air Act and the installation of flue gas desulfurization (FGD) equipment (scrubbers) on coal fired power plants, the management of solid wastes has taken on added importance. Aside from the large amounts of fly ash and bottom ash usually generated, large quantities of liquids in the form of scrubber sludge are also produced. These wastes must be disposed of within the constraints of land and water quality regulations. This paper describes the practices adopted by the electric utility industry in denting with this problem, including methods of generation and treatment, quantities and characteristics of the materials, and transportation and disposal practices. The paper also briefly describes final product characteristics and several applications for commercial utilization and land reclamation.

Jan 1, 1983

By S. J. Ristorcelli

Historically, geologic data has not been adequately considered in resource estimation. More recently, with the use of computers and sophisticated estimation algorithms and geostatistical justifications, geology has been downplayed further. Many reasons are given for not using geology including cost, time and irrelevance. None are valid. Boundaries defining mineral domains should be used in computer-generated resource estimates. Selected case histories show how the failure to honor geology has caused discrepancies in resource estimates of actual in-place resources. After-the-fact differences have included decreases in tonnage of up to 50% and increases up to 300%; partial to complete recategorization of material; and 50% decreases in grade. The costs of gathering and using geology are trivial compared to the potential consequences.

Jan 1, 1994

By N. Arbiter

If two fluid phases are brought into contact with a solid, one fluid may completely wet the surface to the exclusion of the other, or both may wet it, forming a three-phase line of contact. These relative wetting tendencies are quantified by the contact angle 0 which is related by Young's equation (1,2) [12 cos? = 13 ? 23] [to the three interfacial tensions (3). No contact angle for the first fluid, indicating that it does not wet the solid in the presence of the second, means that the difference between the two solid-fluid fluid surface tensions, - 8 is greater than (or just 13 -23 equal to) the fluid-fluid tension 12; a finite angle indicates that the difference is less.*]

Jan 1, 1964

By Andre Vien, Frank Laroche, David Di Sandro

Back in 1994, Claude Bazin presented a novel method for linking size data from milling models to the feed input of flotation models. It was achieved with the simple addition of a metal/mineral distribution—size distribution relationship. This allows grade and recovery predictions from a varying mine plan via product size distribution predictions. This paper presents a case study where this elegant method has been used to build a very powerful forecaster at a process plant, built from historic operating data. The methodology has been used by this operation to forecast production on a quarterly, annual, and life-of-mine basis since the late 1990s. It has been upgraded several times to incorporate new drivers as the complexity of feedstocks has increased over the years.

By J. Groff

The Getchell and Twin Creeks mines are located along a north-northeast trending structural zone in Humboldt county, Nevada approximately 40 miles northeast of the town of Winnemucca. Gold mineralization at the Getchell mine is represented principally by sulfide-rich ores, which contain significant amounts of realgar and\ orpiment, with the gold being recovered through processes which involve pressure oxidation. In contrast, oxide ores are currently being mined and processed at the Twin Creeks mine although large reserves of sulfide ores, some of which contain orpiment-realgar-stibnite, have been defined (Bloomstein et al., 1990). The Getchell and Twin Creeks mines represent major gold orebodies but very little has been published pertaining to mineral paragenesis and the characteristics of ore-forming fluids for these deposits.

Jan 1, 1994

By F. E. Heuze

This article deals with the effects of high-explosive and nuclear explosions in rock masses. We first highlight the strong influence of geological discontinuities, such as joints and faults, on ground motion characteristics. Then, we briefly introduce the Discrete Element Method, as a new technique for numerical simulations. II is shown to be far superior to continuum-based approaches, when dealing with the dynamics of discontinuous media such as jointed rocks. Finally, we simulate the ground effects from a generic contained nuclear explosion, which bears some similarity to the SHOAL event in granite. This calculation is intended to emphasize the influence of the near-source geology on the distribution of energy, and on the motion at various azimuths in the medium.

Jan 1, 1991

By Walter Meintrup

On Nov. 4, 1981 the newly installed 1000tph wet-process iron-ore ball mill of A/S Sydvaranger completed its first four months of uninterrupted, successful full-load operation in Kirkenes/Norway. This 6.5m diameter mill is driven by a gearless ring or wrap-around motor of 8100kW at 13.1RPM - a first of a kind in this segment of industry. (Fig. 1) This paper analyses the reasons that have led to the selection of this type of drive over more conventional schemes, lists specific advantages of such large mills, and describes in some detail the installation in Norway. General aspects of possible design variations, and application information for designers and users of such mills conclude the presentation.

Jan 1, 1982

By G. A. Parkison

The sequential copper analysis method is a particularly useful technique to semi-quantitatively define the geologic, mineralogic, and metallurgical types and zonations commonly associated with porphyry-type copper deposits. The method is based on the partial dissolution behavior displayed by the prevalent copper minerals malachite, chrysocolla, chalcocite, and chalcopyrite to solutions containing sulfuric acid and sodium cyanide. Results from sequential analyses of the sample and analytical residue using sulfuric acid followed by sodium cyanide and then aqua regia solutions when compared with conventional total copper analyses can determine the amounts of leachable oxide minerals, leachable secondary sulfide minerals, and primary copper minerals, respectively. Sequential assay analytical results and interpretation are presented for copper deposits in Chile, Mexico, and the United States.

Jan 1, 1995

By W. H. Langer

Quaternary alluvial deposits in the modern stream channel of the Agua Fria River west of Phoenix, Arizona, is mined and processed to provide aggregate to the greater Phoenix area. The alluvium occurs as three distinct, stratigraphic layers. Samples from each of the three layers were examined for gravel clast lithology, grain size distribution, and engineering tests, which revealed noteworthy differences in properties. The engineering properties of the gravels are dependent on a combination of factors including gravel clast lithology, the distance the gravel clasts have been transported from their source areas, the age of the deposits, and the degree of weathering. Knowledge of these characteristics may affect the methods that aggregate operators employ to extract and process gravel from the Agua Fria River.

Jan 1, 2010

By R. H. Lambeth

Disposal of mine tailings in "waters of the United States" is presently prohibited even though case studies indicate that the practice may be environmentally viable. To simulate disposal in the natural environment, nine containers of tailings and sediment were instrumented and placed on the ocean floor near Juneau, AK as were ninety-six biosample containers. Pore water concentrations of five metals were determined, and biota populations were characterized for both materials. After 500 days of exposure there were no statistical macro scale differences between tailings and sediment biota populations or Cu, Pb, and Zn pore water concentrations. Tailings released slightly more Fe than sediment, but sediment released significantly more Mn than tailings. Disposal of mine tailings in marine waters may be environmentally safe.

Jan 1, 1998

By J. T. YIi-Penttiia

Dust formation and reaction mechanisms of copper matte particles were investigated in simulated flash oxidation conditions. The granulated and ground matte consisted of 72 wt% Cu, 4 wt% Fe and 21 wt% S. Experiments were conducted by using a laminar-flow furnace with a reaction gas composition ranging from 20 vol% to 75 vol% O2 in nitrogen. The particle feeding was carried out by the single-particle method and samples were quenched after a specified reaction time (approximately 0.05-004 s) in a cold water film. Experimental temperatures were between 800 and 1300°C. Chemical analysis was used to determine oxidation degree, and an optical and scanning electron microscope combined with energy dispersive analysis was used for characterization of the reacted particles.

Jan 1, 1998

By R. K. Rajamani

The theoretical model based on fluid mechanics, in conjunction with the laser-Doppler velocimetry (LDV) measurements, elucidate the size-classification mechanisms in an industrial hydrocyclone. The model has no adjustable parameters and involves solving the Navier-Stokes equations to predict the liquid-phase velocities. The spatial-concentration gradients were determined considering the particle phase in the Lagrangian frame and the classification curve was determined by balancing the forces acting on the particle. The force balance requires liquid velocities, which in turn depend on the local volumetric concentration of the particles. Hence, complete modeling work involves coupling both the concentration and liquid-phase velocity calculations until convergence is reached. Finally, the experimental and predicted classification curves were presented for 250-mm hydrocyclone operating at high-percent solids.

Jan 1, 1994

By G. ALBORNOZ, S. Utili, A. AGOSTI, C. VALDERRAMA, R. PELL

The steepness of an openpit mine’s slopes has a substantial influence on the mine’s financial return. This paper proposes a novel design methodology where overall steeper pitwalls are employed without compromising the safety of the mine. In current design practice, pitwall profiles are often planar in cross section within each rock layer: that is, the profile inclination across each layer tends to be constant. Here, instead, a new geotechnical software, OptimalSlope, is used to determine optimal pitwall profiles of depth-varying inclination. OptimalSlope seeks the solution of a mathematical optimization problem where the overall steepness of the pitwall, from crest to toe, is maximized for an assigned lithology, geotechnical properties and factor of safety (FoS).

A parametric study was conducted to establish the optimum operating conditions for the column flotation of fine coal. The parameters examined in this investigation included collector and frother dosages, feed solids content, and the volumetric flow rates of feed slurry, air and wash water. Despite the wide range of conditions studied the experimental data were found to fall along single grade-recovery curves, just below the maximum separation predicted by the release analysis technique. The deviation of the parametric test data from the release curve was attributed to the nonselective entrainment of mineral matter associated with poor froth washing. The operating point on the characteristic recovery-grade curve was found to be primarily determined by feed rate and aeration rate.

Jan 1, 1992

By Thomas L. Kesler

Lithium raw materials usable with present technology consist of pegmatite ore and surficial evaporite brine. Those advantageously located now supply world markets. Materials of similar grades and magnitude, but less favorably located, will come into production as present sources are depleted and markets expand. Some of these potential supplies have been explored, and are reserves in the sense of known availability and quality. Reserves herein are of two classes, those proved by close drilling and assaying, and those of only probable status because their scale and grade are unsystematically indicated. Possible resources include similar materials whose bulk can only be inferred on indirect evidence. All figures apply to total materials in the ground. No allowance is made for losses in mining, evaporation, beneficiation, or chemical processing.

Jan 1, 1977

By C. L. Schneider

The calculation of the liberation spectrum in the product from continuous milling operations is a problem of considerable importance and is difficult to solve because the population balance equation must be integrated in two-dimensional space. Complete solutions require the estimation of a large number of parameters unless a structural model of the ore texture can be used. A very simplified textural model based on the use of the modified Andrews-Mika diagram and the PARGEN simulation of multi-phase particles has been formulated and is used to simulate the behavior of a continuously operating laboratory ball mill. A sensitivity analysis for this mill has been done to show the likely effect of model approximations on the predicted liberation spectrum which will be measured.

Jan 1, 1992

By Mustafa Akser

The Pipestone Lake anorthosite complex in Manitoba, Canada, was recently been re-identified as a potential source for titanium, iron, and vanadium. The present study utilized a 350 kg hard rock sample, which originated from the "Main Central" zone of the deposit. Commercial pilot-size equipment, such as dry low intensity roll magnets, wet high intensity magnets (WHIMS), and high tension electro-dynamic roll separators, was employed. As products, ilmenite up to 48.5% TiO2, and magnetite concentrates up to 87.9% Fe3O4 with 5.25% TiO2 were obtained. The majority of the vanadium reported to the magnetite concentrate. Subsequent characterization of various separation products shed light on the potential grade and recovery of the minerals from this deposit.

Jan 1, 1996

By Kunio Hashimoto

The conventional troughed belt conveyor system is the most widely used form of equipment for transporting bulk materials in the world today. The reason is not only because it is possible to transport a great deal over a long distance when compare to other types of equipment but also due to its greater economic efficiency and low initial and running costs. When dry, powdery materials and liquid materials are being conveyed, there are enclosed transport methods such as flow, case, air-slider and pipe line. In addition to features of the belt conveyor, a system employing a pipe line to transport dry powdery and liquid materials has always been considered an ideal method. This has been brought into reality through the Pipe Conveyor Sys tem.

Jan 1, 1984

By M. J. Laurila

On-line analyzers have made possible the use of Fuzzy Logic Control (FLC) for local control applications in coal preparation plants. This includes FLC control of complete circuits such as heavy media vessels, cyclones and froth flotation. These circuits can be controlled in real time in a feedback control loop with an on-line analyzer. Control strategies can be readily developed using Statistical Process Control (SPC) techniques which are first applied off-line in manual mode through the use of control charts and then this process is brought on-line using FLC in conjunction with an on-line analyzer to fully automate the circuit. This paper outlines the types of control strategies employed and presents examples of automatic verses manual control.

Jan 1, 1997

By V. K. Gupta

The phenomenon of zero order production of fines associated with the batch comminution of monosize feeds in tumbling mills has been examined in the context of the size discretized population balance model. It has been shown that the model admits zero order production kinetics only in an approximate sense. The necessary and sufficient conditions for approximate zero order production of fines have been obtained. As these conditions cannot be expressed in terms of the model parameters Sj and Bi,j alone,. several examples have been used to illustrate some of the important characteristics of the zero order production systems. One of the important characteristics of these systems has been identified as a "weak necessary condition", and the other as a " favourable condition ".

Jan 1, 1985