Search Documents

By D. W. Boening

Xanthate salts have demonstrated effectiveness as a flotation reagent in the recovery of heavy metals from mining wastewater. However, due to their strong ionic potentials, they are generally toxic to aquatic life. Under ambient environmental conditions, the half¬life of a xanthate is approximately four days. As a soluble salt, xanthates will complex with the metallic ions contained in water and fish. Some researchers have proposed that this complexing may extend the halflife, as well as optimizing the transfer of a given metal from solution across the gill surface. Leakage of xanthate treated wastewater into the surrounding surface waters is the most common route of exposure for aquatic plants, invertebrates and fish. Because this is an emerging mineral-recovery technology, more information is needed regarding xanthate toxicity and environmental fate before environmental impacts can be assessed with any degree of certainty.

Jan 1, 1999

By S. R. Rao, J. A. Finch, E. El-Ammouri, K. Ngoviky, P. A. Disten

Sludges produced by lime treatment of acid mine drainage (AMD) can contain significant quantities of base metals which represent both a potential hazard and a loss of values. A new technique for metal recovery from sludge is proposed by combining selective acid leaching and adsorption of metal ions by activated silica sol. The process is demonstrated on two AMD sludges, one containing primarily nickel and the second zinc. They were first treated with sulphuric acid (pH 3.5) to selectively leach the target metals and then activated silica sol was added to the leach solution to adsorb the nickel and zinc. Thickening and centrifuging gave about 90 percent rejection of the input volume to effluent. The adsorbed metals were redissolved by strong acid into a concentrated solution relative to the feed and the silica sol was recycled.

Jan 1, 2000

By Drupad B. Desai, Alexander Rosenbaum

In recent years, there has been an increasing use of two-pass tunnel lining system consisting of segmental unbolted expandable precast concrete initial lining and cast-in¬place concrete final lining in the United States. Used so far in soft ground tunneling performed under free air, it often includes a waterproofing or gasproofing membrane placed between the initial and final linings. This paper describes the utilization of this two-pass system for an extension of the Baltimore Metro, constructed in part under compressed air. It offers a description of the extension project, known as Section C; addresses the tunnel lining selection process and the design of the lining elements; examines the effect of the adopted lining system and tunneling technique on the design of the project's major structural components; and describes design modification instructions in order to accommodate constantly changing field conditions.

Jan 1, 1993

By A. Gene Collins

The demand for lithium may increase because of its potential use id lithium batteries and in the generation of electrical power by fusion. Therefore, lithium abundance in some United States oil-field brines was surveyed. Oil-field brines from numerous locations were found to contain more than 100 mg/l lithium and several exceeded 500 mg/l. An area of 25,000 km2, with a reservoir thickness of 60 m, an effective porosity of 5 percent, and a brine with a specific gravity of 1.2 containing 100 mg/l of lithium, contains about 0.75 x 106 tonnes (1 tonne = 1 metric ton = 1,000 kg) of lithium in 7.5 km3 of brine. It is postulated that the brines were enriched in lithium by lithium-rich spring water or lithium leached from volcanic rocks followed by evaporation sequences.

Jan 1, 1978

By Harold D. Taylor

Lognormal grade distributions are definitely the rule rather than the, exception in many types of deposits, including precious metals, uranium, and many others. The "normal theory" geostatistical techniques do not work well in these situations because the occasional high grade values, perhaps several orders of magnitude larger than the median, can overwhelm the rest of the data, resulting in variograms and Kriged estimates which are unrealistic or even ridiculous. Robust techniques for variogram modeling have been proposed, and truncation of high sample values can produce more reasonable Kriged estimates, but the technique of working with log transformed data appears to be the best method of handling lognormal data. This paper will discuss primarily the two parameter lognormal case, with some discussion of the three parameter lognormal, but no discussion of other methods of transforming data, such as disjunctive Kriging.

Jan 1, 1982

By Yongping Hu, Dianchen Cai, Congya Zhang

China is a rich in stromite mineral resource. Unfortunately, the resource is very difficult to separate by using conventional flotation method because stromite and gangue minerals are very fine disseminated, the average size of them is about 10 µm or below, and the content of clay minerals such as illite is 19% or even more. In this paper, the aggregation floatation behavior of ultrafine (-10 µm) stromite, illite, ablbite and quartz using anion collector were studied. The result show that, Oxidized paraffin (O.P) is a good collector and has better selectivity for stromite particles flotation. The salted sodium silicate depressed illite gangues minerals effectively. The separation of mineral mixtures was carried on successfully at one stage flotation by the technique. The mechanism of O.P. and salted sodium silicate were studied and discussed by using IR and Zeta- potential measurements.

Jan 1, 1995

By Bob Gordon, Allen Furth, Dan Dobbels

A 4.8 m (16 ft) diameter hard rock tunnel was driven through granite bedrock to create the 1.7 kilometer (1.1 mile) long Hampton McCloy Retention Tunnel for the city of Richmond, Virginia. During the work the tunnel encountered narrow seams of partially decomposed granite that were not self supporting and could be dealt with using ribs and lagging. However, as the tunnel approached the receiving shaft, it encountered a large seam of highly decomposed rock, alluvial deposits and running sand which resulted in soil loss into the machine. As a result of this condition, a jet grouting program was quickly developed to allow the tunneling to continue. This paper will describe the manner in which jet grouting was used to solidify and stabilize the decomposed bedrock, alluvial soils, and running sand to allow the TBM to continue tunneling.

Jan 1, 2003

By J. E. deMasi

Over the past 12 years, Exxon Coal U.S.A., Inc. has shipped over 150 million tons of coal from two mines, Rawhide and Caballo, located in the Gillette, Wyoming, area. These mines are operated by The Carter Mining Company, a division of Exxon Coal. Shipments have moved to more than 25 electric utility plants in the west, midwest, southwest, and south. The customer plants have represented a wide variety of configurations, sizes. design criteria, emission standards, and operations in different parts of the country. We have learned a great deal about the performance of Gillette area coals in utility power plants during this period. This paper covers some of the highlights of Exxon's experience with these coals in customer plants. I will focus specifically on things mining engineers may be able to do to make the product better for the customer's use.

Jan 1, 1989

By P. Somasundaran

Beneficiation by froth flotation, which exploits the difference in surface properties of minerals, has been a promising method for coal cleaning. However, dissolved mineral species present in coal flotation systems can interact with particles and other species leading to drastic effects on flotation. Particularly, precipitation or adsorption of such species on the particles can alter their surface properties and thus influence the efficiency of coal cleaning. In this work, the bulk and surface precipitation of the dissolved mineral species present in Pittsburgh No. 8 coal was investigated under controlled experimental conditions. Changes in the surface properties of coal due to the precipitation were monitored by following zeta potential. Solution potential data were used to elucidate the mechanism of the precipitation. The effect of the precipitation of the dissolved species on the floatability of coal was found to be marked.

Jan 1, 1995

By Steven W. Hunt, Ronald E. Heuer, Safdar A. Gill

A 3.3 m (11 feet) diameter, 51 m (168 feet) deep temporary steel casing which had been sunk within glacial soils buckled and collapsed on July 29, 1985. The collapse occurred at the CT-8 Dropshaft site in Milwaukee while two workmen were contact grouting outside the casing in an attempt to stop groundwater inflows through a bottom plug. This paper describes the soil and groundwater conditions at the site, the casing design, the method of shaft construction, and probable causes of the buckling failure. Specific aspects of the paper include: slurry method of shaft excavation and casing installation, soil creep, earth pressure due to three dimensional arching, and buckling strength of a casing surrounded by slurry rather than grout and firm soil. The paper should be of interest to designers and constructors of temporary ground support systems for deep shafts.

Jan 1, 1995

By S. K. Kawatra, T. C. Eisele

Although column flotation is known to be more effective than conventional flotation for cleaning fine coal, little attention has been paid to the considerable sulfur removal potential of this process. Whereas conventional flotation can only with difficulty remove pyritic sulfur from coal, flotation columns can make this separation readily due to their greater selectivity. This project has used a modified flotation column to remove pyrite from fine coal. This column has been shown to be capable of removing 70 to 85 percent of the pyritic sulfur from coal while recovering 80 to 85 percent of the total calorific value. However, the remaining pyrite is too finely disseminated to be readily removed by physical means. Currently, experimentation is in progress using bacterially-catalyzed dissolution of pyrite in acid solution to remove ultrafine pyrite and aid in the removal of coarser pyrite inclusions.

Jan 1, 1988

By David C. McLean, Peter Penner, Martin de G. Salter

The Rogers Pass Project for C.P. Rail includes a 14.7 km tunnel and an 8.5m diameter concrete lined ventilation shaft to a depth of about 335m. The shaft collar is in bouldered water bearing glacial till to a depth of about 95m. Initial excavation in the overburden was with the aid of dewatering wells. When ground support problems arose the excavation was completed by a two stage freeze programme. Freeze holes were drilled from the shaft bottom. This most unusual method was successful in overcoming the difficulties safely and efficiently. The remainder of the shaft was sunk and lined conventionally. Finally, a central dividing wall was poured by jump forming from the bottom up. The wall was completed to a high standard at up to about 20 vertical metres per day.

Jan 1, 1989

By Fred V. Carrillo

California was the leading state in industrial mineral production value with an estimated value of nearly $2 billion. In total value of U.S. non-fuel mineral production estimated for 1992 by the U.S; Bureau of Mines, California ranked second; 81 % of California's total production value was derived from industrial minerals. California led all other states in the production of boron minerals, portland cement, diatomite, calcined gypsum and construction sand and gravel, and ranked second in potash and soda ash production. California's five leading industrial minerals in terms of value were portland cement, construction sand and gravel, boron, crushed stone, and soda ash. California had 13 additional industrial minerals production with reported sales of over $1 million including; industrial sand and gravel, magnesium compounds, lime, salt, potash, natural sodium sulfate, clay, feldspar, crude gypsum, pumice, dimension stone, calcium chloride and perlite.

Jan 1, 1995

By G. Johnston, P. K. Chatterjee, S. Holguin

Underground mine planning is largely manual and can demand considerable resources to generate a working plan and to perform limited tests of sensitivity to variations in geological and mining conditions. It is possible to use computer aided mine planning to automate many of the manual procedures to allow the planner to evaluate a number of layouts, extraction strategies, and schedules. his paper examines the simulation and scheduling of an under- ground coal mine operation through the-use of on- screen graphics. The simulation will provide a basis for predicting productivity and other relevant information over a specified number of shifts. The software developed is extremely user friendly and reduces the tedium of repetitive manual calculations inherent to mine planning and drafting to a minimum, thus offering considerable savings in an area that is widely recognized as extremely labor intensive.

Jan 1, 1988

By J. S. Anderson

Size reduction models of cone and impact crushers have been developed using Whiten's generic computational structure for the description of crushers. They incorporate a laboratory single particle breakage test and the t-family of curves to describe the breakage behaviour of the feed ore. A quantitative model of 7-foot cone crushers has been developed, based on surveys of Svedala (Kobe) and Nordberg machines. Survey data on a Canica vertical shaft impact machine have been used to validate the impact crusher model. Given the crusher operating conditions, such as tonnage, feed size, set and liner condition, or rotor speed and radius, plus breakage information on the feed, the models provide good predictions of product size distribution, and appear to be robust over a wide range of conditions. They are incorporated in commercially available computer simulation packages.

Jan 1, 1998

By B. H. Richard, P. J. Wolfe, T. G. Holdeman

Guided seismic wave propagation was studied in the Lower Freeport (6A) coal seam in the Oak Park No. 7 mine near Cadiz, OH. Three component geophones were implanted in the coal at distances ranging from 72 m to 183 m from the seismic source. Both Love- and Rayleigh-type modes were observed but the Love-type mode produced the best data. Detailed analysis was performed on the best Love data and a Dziewonski map of group velocity vs. frequency was constructed. This map was in excellent agreement with a theoretical dispersion curve calculated for a model of the coal seam. The Love wave group velocity was found to have a minimum value of 510 m/sec at 275 Hz. Only the fundamental mode contributed significantly to the observed signal and it was observed up to the maximum distance available.

Jan 1, 1987

By Wojciech Suwala

The transition from centrally planned to market economy affects methods of economic analysis. The models which were used in the past are riot valid presently, however they we're the seed which initialized the development of methods and applications. There is more than twenty years of experience in modeling of coal mining development. The first attempts were devoted to select the moment of mine construction commencement in order to meet planned output. In Poland significant development of such models began in 1986. Within the Central Research and Development Program there has been a continuous development of models. These models from econometric to optimization ones, were a certain sequence which, in accordance with changing economy system, led to the last version of the model. It is the most suitable one for contemporary problems of coal mining in present Polish circumstances.

Jan 1, 1992

By Zhen-lu Zhao

The manipulators possibly used in underground mining must deal with unpredictable obstacle while keeping certain positions and orientations of end effector, and in some cases, are required to possess redundant joints in order to be more flexible. This kind of manipulators might be fitted with jumbo drill or platform as auxiliary to potentially deal with some utility works in versatile way, such as installing rock bolts, guniting, blasting, charging, surveys and measuring work, etc.. This paper describes numerical procedures of performing inverse kinematic problems for redundant manipulators .The procedures, based on the generalized pseudoinverse of Jacobian matrix, are developed to lead to kinematic solution at both singularity and ill conditioning, and to guarantee continuous sequence of positions of the end effect or. Furthermore, the solution to optimization and obstacle avoidance is investigated. A numerical example is shown to illustrate the approach.

Jan 1, 1989

By J. L. Hendrix, M. Ahmadiantehrani, G. Ramadorai

The concept of hypochlorite treatment prior to cyanidation in the heap leaching of low grade carbonaceous gold ores is discussed. Laboratory column leach tests using a low grade carbonaceous ore were performed to investigate the effects of pH, hypochlorite consumption and concentration, and bed height on total gold extraction. At high pH, hypochlorite stability increases and thus, hypochlorite consumption decreases. At room temperature, total gold extraction is proportional to hypochlorite consumption. However, at some point additional hypochlorite consumption does not increase gold extraction. Gold recoveries of 10% and 80% are achieved at 12 and 167 lb/ton hypochlorite consumption, respectively. Increasing hypochlorite concentration increases the rate of extraction. For a given hypochlorite consumption, gold extraction increased with decreasing ore bed height. Finally, using calcium hypochlorite results in higher gold extraction than using sodium hypochlorite at a fixed hypochlorite consumption.

Jan 1, 1992

By J. Y. Kim, R. W. Stanley, L. Rosato

Silver contained in zinc calcines undergoes several phase changes as it proceeds through the leaching circuit of a roast-leach-electrowin zinc plant. In this study, the flotation response of silver, from leach residues prepared under a variety of carefully controlled operating conditions in the pilot plant has been examined. Flotation of neutral leach residue is shown to be technically viable and to merit consideration for those plants without a high-acid leach circuit, but having significant silver values in the feed. Residue leach conditions must be kept slightly acidic to promote the formation of Ag2S, (AgCu) 2S and Ag2S rims on residual unroasted sphalerite, while simultaneously avoiding the hydrolysis of soluble iron, which depresses silver recovery and grade. Factors to be considered during integration of a flotation process into an electrolytic zinc plant are discussed.

Jan 1, 1992