Search Documents

By J. F. T. Agapito

Two flat-lying trona seams 3-to 3.5-m thick, approximately 10 m apart, and at depths of 250 m are mined by room-and-pillar at OCI's Big Island Mine in Wyoming. Continuous miners and a yielding pillar system have contributed to improvements in resource recovery and productivity. Long-term stability with minimal subsidence is needed for a large portion of the mine beneath the Green River channel. This was investigated by computer modeling in 1990. Although results of the study indicated good long-term stability, recommendations were made for stress determinations to verify the model. Stress determinations made in 1997 showed pillar stresses 10% to 20% higher than the model stresses, and barrier pillar stresses 10% to 15% lower. This implies that higher panel stresses will be transmitted from the upper to the lower seam. A stability evaluation of the lower seam is planned before two-seam mining to assess entry widths and support requirements.

Jan 1, 1999

By Young C. Kim

In the past, underground coal mine planning has traditionally focused on the mine design n aspects concerning safety and efficiency in the quest to produce low cost coal. Very little attention has been given to coal quality control aspects of mine planning at most of the underground coal mines within the U.S. With the enactment of the clean air act of 1970, the generally high sulfur content of coal has become a major concern for the coal-fired power plants in the east. Similarly, the ash and the BTU contents of coal are of equal importance from boiler efficiency standpoint. Thus, the time has come when the coal mine planning must incorporate the coal quality control aspects as well as the traditional safety and efficiency aspects.

Jan 1, 1983

By Ross K. Digby

The Victorian Tunnelling Centre (VTC) has evolved its purpose from purely training workers, to a tunnelling industry education city. The VTC has now focused its activities on the areas of technology; education and training; applied research; and career education. were identied as the hus around which activities would e conducted to create a tunnelling industry education city. The VTC provides ustralias tunnelling industry with an education facility that not only provides laour training, ut enales the industry to come together to meet, participate in product launches, undertake research, work with new technologies and promote tunnelling careers.

Jun 23, 2024

By K. Adam

Improved environmental performance comprises one of the key objectives of the sustainable development in the mining industry. Within this framework, a research project was undertaken by TVX Hellas, a mixed sulphides producer in northern Greece, in order to develop and evaluate anaerobic wetlands as an alternative method for the treatment of acidic waters originating from old mine areas. The anaerobic treatment using organic substrates, aimed to neutralize the acidity of the mine drainage and remove the dissolved metals, such as Fe, Zn, Mn etc., in the form of insoluble compounds retained within the substrate. The effectiveness of this treatment method, as compared with the conventional neutralization techniques with alkaline additives, extensively used in the mining industry, was assessed based on environmental and economic indicators. The indicators applied included contaminant removal, land take per unit of contaminant removed, effluents quality, remediation of past environmental damage, energy and reagents consumption, capital and operating cost. Based on the above, the applicability of anaerobic wetlands for the treatment of acidic streams originating from old mined areas was concluded.

Jan 1, 2003

By R. Miller

Lowering our globe’s emissions is a major effort as we move toward a future net-zero carbon environment requiring significant investment in a new, low-carbon infrastructure, along with key market incentives to change. Industry will play a key part in this transformation, requiring expertise in both energy and emissions. Key elements of the de-carbonization strategy are: energy data, emissions reporting method, governance, de-carbonization project generation and drivers, the MACC, electrification, and the de-carbonization checklist. For a zero carbon future, it will be key for business leaders to understand decarbonization, anticipate technological changes, and implement new business me

Mar 2, 2022

By J. Larsson

In the pursuit of increased safety the mining industry has worked to develop systems for remote control and autonomous operation of both stationary and mobile equipment. This paper reports on a newly developed system for teleoperation and autonomous tramming of LHD (Load-Haul-Dump) mining vehicles that not only increases the safety of the operators, but also has the potential to increase productivity.

Jan 1, 2010

By F. Stanley, A. Noble, G. Luttrell

"The supply chain for coal-fired power stations involve a multi-stage network of mining units, preparation plants, blending facilities and transportation systems. Attempts to optimize the supply chain have historically been difficult due to the lack of communication/coordination between the various groups involved in coal production, transportation and utilization. In light of this issue, a new approach for globally optimizing the coal supply chain called Micro-Price Optimization has been developed to simplify the optimization problem and to provide coal producers with fundamental insight needed to improve the profitability of their operations. This fundamental concept assigns unit values to each particles (or groups of particles) passing through production units. Optimization occurs whenever the maximum tonnage of positive value particles are recovered and passed to market, while the minimum tonnage of negative value particles are recovered. Elements considered by the concept include factors such as target boiler cost/efficiency, waste disposal costs, coal quality parameters, emission penalties, transportation charges, or other quantifiable impact factors. This article reviews the basis for the micro-price concept and provides a detailed industrial case study involving the determination of optimum coal qualities that need to be supplied by mine operators to feed a coal-fired power station. INTRODUCTION The performance of coal preparation plants have long been known to play an important role in determining the overall profitability of mining operations. This significance is due to the fact that the misplacement of just 1 ton/hr of clean coal to reject resulting from poor plant performance can represent nearly $300,000 per year in lost revenues for a mine producing a steam market coal (i.e., 1 ton/hr x $50/ton x 6,000 hr/yr = $300,000/yr). This loss can be even more pronounced, occasionally approaching $1 million per year for each 1 ton/hr of misplaced clean coal, for operations producing high-quality coking coal products sold into the premium metallurgical market (i.e., 1 ton/hr x $150/ton x 6,000 hr/yr = $900,000/yr). Detailed economic studies indicate that improvements in plant yield resulting from increases in organic efficiency have one of the largest overall impacts on mine revenue when compared to other cost centers within the mining operation. One of the first studies to show this important financial impact was reported by Norton-Hambleton Consultants (Norton, 1979). Their study indicated that an unfavorable change in plant efficiency was second only to coal transportation in terms of its impact on profitability, while an unfavorable change in the cost of underground mining was a distance third. This longstanding realization has continued to provide a strong financial incentive for coal producers to optimize the separation efficiency of their coal processing and blending operations."

Jan 1, 2015

By Christopher Nelsen, Daniel Dobbels, R. Zachary Hollenbeck

Recent major floods have inundated Historic Ellicott City, Maryland, resulting in loss of life and property damage. Howard County, Maryland, has developed the Ellicott City Safe and Sound Plan to mitigate the risk of flash flooding in the Historic District, including a proposed stormwater conveyance tunnel. Challenges to overcome include thick zones of saprolite along the alignment, multiple near-surface structures, and minimal rock cover under an active railroad, while minimizing impacts to the public and historic structures. The project will also pursue recognition through the ISI Envision verification process.

Dec 1, 2022

By Harold R. Kokal, Madhu G. Ranade

A metallurgical/flux is a substance that is added to combine with gangue (unwanted minerals) during ore smelting, with impurities in a molten metal, or with other additives in metal refining processes to form a slag that can be separated from the metal. Because slags are immiscible with the metallic melt and are of lower density, a separation of the slag and metal occurs if the viscosity and surface tension are of the proper values. The chemistries of slags are adjusted to provide the proper melting point, viscosity, surface tension, conductivity, specific heat, density, or chemical properties to effect the desired task. In addition to absorbing impurities from the metal, the purposes of the slag are to thermally insulate the metal bath, protect the molten metal from the atmosphere, and control the chemical potential of the system. Several excellent references on slags and metallurgical fluxes are available (Boynton, 1980, Lankford, Jr., et al., 1985, Turkdogan, 1983, Rosenqvist, 1974, Fine and Gaskell, 1984). The function of the slag might vary at different stages within a process prior to final melting. For example, the slag composition and behavior will change as materials descend in the iron blast furnace, or as they melt in the early stages of formation of steel- making slags. Selection of the chemistry for a slag might be influenced by factors outside the primary function as when blast furnace slags are used to make cement, rock wool insulation, or fertilizer supplements. Sometimes slags contain a sufficient amount of valuable recoverable elements to be sold as raw materials for other processes. Fluxes are often referred to as acid, basic, or neutral. Acid fluxes are those that generally form acids in water and bases are those that would generally form bases in water. Typical acid fluxes are silica, alumina, and phosphorus, although alumina can function as either an acid or base. Typical basic fluxes are lime and magnesia. Fluorspar, or calcium fluoride, is a neutral substance because it can be viewed as the reaction product of a base and an acid. The degree of acidity (ratio of acids to bases) or basicity (ratio of bases to acids) is often specified to characterize the slag chemistry for a particular system. The system might also be referred to as acid or basic depending on the choice of slag, for example, basic steelmaking uses slags with more bases (lime and magnesia) than acids (silica and alumina). Many forms of minerals and compounds have been used as fluxes depending on the process requirements, availability, costs, requirements for recycling of intermediate products, and environmental concerns. Because slags are most often mixtures of oxides and silicates, fluxes are usually oxides, carbonates (which decompose to oxides) and silicates. Slags comprising phosphates, borates, sulfides, carbides, or halides have also been used (Rosenqvist, 1974, Moore, 1981, Szekely et al., 1989). In ironmaking and steelmaking, some acidic components are sometimes added. In nonferrous processes slags and fluxes are acidic with silica as the primary component, and although the use of basic flux such as limestone or lime is not extensive, some amount is used to modify slag properties and some refining slags are lime based. The production of iron is accomplished by smelting of ores, pellets, and sinter in blast furnaces with subsequent refining of molten iron and scrap in oxygen-blown processes. The electric furnace is used to make steel, stainless steels, ferroalloys, and special alloys, whereas ferromanganese is often made in blast furnaces. Fluxes are used in all of these processes, and either limestone or lime is the major flux component with some dolomite, dolomitic lime, silica, alumina, and fluorspar being used. In ironmaking, the flux is added either by direct charging or through sinter and fluxed pellets. In steel refining by the basic oxygen process, flux is added as lime and dolomitic lime that are either charged as lumps or injected as fines. Some small amount of limestone is sometimes used. Fluorspar is often added as lumps or mixed with other fine materials in briquettes. Alumina is sometimes added to blast furnaces either by direct charging of sized lumps or through sinter. Typical acid fluxes are sand, gravel, quartz rock, used silica brick, or raw siliceous ore (Lankford, Jr., et al., 1985). Olivine, which is a magnesium-silicate mineral, has been added to iron blast furnaces to enhance removal of alkalis (Lankford, Jr., et al., 1985). Alumina in the form of bauxite, aluminiferous clay, and recycled alumina brick has been used as flux. Alumina can function amphoterically as either an acid or base, for example it can form aluminum silicate in high silica slags or calcium aluminate in lime-bearing slags (Lankford, Jr., et al., 1985). Limestone (calcium carbonate) and dolomite (magnesium-calcium carbonate), or fluxstones as they are sometimes called (Boynton, 1980), and their calcined forms, lime and dolomitic lime are the major basic fluxes. In the latter cases, the carbonates are de- composed in a kiln-type process to drive off carbon dioxide that might otherwise interfere with the subsequent smelting or refining process or require expensive forms of energy to effect the decomposition (e.g., by combustion of coke in the iron blast furnace). Limestone is considerably less expensive than lime because it is not calcined; however, lime is far more difficult to handle and reacts readily with water. Dolomite and dolomitic lime are used for their magnesia content. Fluorspar is a neutral flux often used as an additive in steel- making slags to improve fluidity, but it has also been used in combination with lime as a primary slag in electroslag refining (Duckworth and Hoyle, 1969). Fluorspar is available in several grades, with the lowest grade often used for steelmaking. When the price of fluorspar has risen, substitutes including aluminum smelting dross, borax, manganese ore, titania, iron oxides, silica sand, and

Jan 1, 1994

By Victor Despointes, Stephane Polycarpe, Kathryn Kelly, Chris Feeney, Brian Hann, Vojtech Ernst Gall

The Pawtucket Tunnel is a 2.2-mi, 30.2-ft diameter CSO storage tunnel in Rhode Island. The primary tunnel is built using a dual-mode open-EPB TBM capable of sealing the face within 120 seconds to manage poor ground and water ingress which is launched from within a SEM starter tunnel. The main tunnel connects to four adits along its alignment, three of which are SEM tunnels and one being a MTBM tunnel. This contribution describes the selection process, potential risks, and requirements for the TBM, as well as the design of the main tunnel, the adits, and the adit-bored tunnel connections.

Jun 13, 2023

By Michael Prince

"Managing slurry is a constant challenge for mining operations. Since slurries are not uniform, the challenge is complicated by varying rheology, velocity, temperature and pressure, all of which affect how the slurry moves through the pipeline and how destructive it is to the system it is flowing through. Picking the right equipment from the outset — the right size pipe, the right size pump and the proper valves for the application — allows mines to operate more efficiently. Better valve designs deliver multiple benefits — they can lower the cost of operations, reduce the amount of maintenance and associated downtime required and are better for the environment. Historically, modulating systems have used ball, plug and pinch valves to manage the flow of slurry, but each of these alternatives has limitations. Ball valves require ceramic lining in order to delay wear, and once a ball valve does wear, the entire valve must be replaced. Similarly, plugs in plug valves should be coated to perform in control systems, and whole valves must be swapped out upon wear. Pinch valves are expensive and only require replacement of the sleeve. However, sleeve replacement involves an extremely arduous process in which the valve is completely taken apart.Traditionally, designers have avoided using knife gate valves (KGV) in modulating systems because KGVs have not been able to hold up under the harsh operating conditions. The throttling that is required in some of these processes rapidly fatigues conventional KGVs, rendering them useless and in need of replacement. Fortunately, innovative design changes have the potential to change established views.Breaking new groundRecognizing the need for improved components, Victaulic took on the challenge of designing a valve that could withstand abrasive slurry systems for a much longer period of time. The first step in this process was to talk to miners, maintenance personnel, process engineers and operators in the field about the limitations of current offerings and then determine design specifications for an ideal replacement.Many of the responses to these inquiries were very similar and reflected challenges with current operations; the primary objective was to find a valve that would be lighter and cheaper than the valves currently in use. In theory, a lighter valve would be easier to replace, and since replacements need to be performed frequently, a cheaper valve seemed like the right idea."

Feb 1, 2019

By Sandip K. Mukherjee

In underground mining operations, ventilation and water sprays are the common methods of controlling dust. In recent years there has been a proliferation of technical literature dealing with water sprays for dust control. However, guidelines for the design of an effective water spray system have not been presented to the mining industry. This paper reviews developments in water spray dust control technology and recommends guidelines for water spray systems to control dust in under- ground coal and non-coal mining operations. These guidelines suggest type, number, location and orientation of nozzles, desirable operating water pressure, and associated filtration system.

Jan 1, 1983

By Irene Bendanillo, Canon Cheung, Justin Lianides, Derek Penrice

The SLAC National Accelerator Laboratory’s two-mile-long particle accelerator generates the world’s brightest X-rays from its Linac Coherent Light Source (LCLS) freeelectron laser. This facility has driven groundbreaking discoveries in medicine and industry. The LCLS-II-HE project will provide a significant increase in laser energy, allowing cutting-edge research in fields including biology and environmental science. A key project component is the Low Emittance Injector Tunnel (LEIT), a 240-foot-long tunnel to be built alongside the existing accelerator and connected to it via a 30-footlong Transfer Tunnel. This paper discusses site and scientific constraints that led to the selection of the LEIT configuration: tunnels to be constructed using the sequential excavation method in mixed-face conditions comprising native rock and placed backfill, and critical design considerations including protection of overlying and adjacent historic structures and structural accommodation of near-fault seismic loading.

Jun 13, 2023

By Todd Kilduff, James Grillo, Shrey Arora

In efforts to improve ingress/egress from the existing subway platforms in PATH’s Exchange Place Station, a new 18-foot horseshoe cross-passage tunnel was constructed by Walsh Construction who retained Kilduff Underground Engineering for design of the initial support system and to install and maintain geotechnical instrumentation. The project presented some unique challenges as a result of the proximity to pedestrians on the platform. PATH service remained uninterrupted, limiting the Contractor to mechanical means of excavation to advance the heading. The logistics proved very challenging for the approximate 100-foot-long tunnel excavated in soft Manhattan Schist. This paper will present the design and construction challenges for the project.

Dec 1, 2022

By H. Dreissen

Upgrading of low-concentration ores is of growing importance today. The Heavy Medium Cyclone Process, thanks to strong centrifugal forces, effectively separates particles varying only slightly in specific gravity but widely in size. The paper discusses the separation efficiency, the method of assessing that efficiency, and the influence of such factors as medium solids. The operating results of nine heavy medium cyclone plants handling following minerals are reported: barite, wolfram, iron, magnesite, diamond, lead-zinc, fluorspar, rocksalt potash. Highlighted are an improved recovery system for heavy medium and some other developments, such as techniques for separation down to 0.1mm and the application in the field of recycling.

Jan 1, 1980

By T. Ritzel

Predictive maintenance technologies including vibration analysis, tribology, infrared thermography, ultrasonic detection, and electrical measurements have been applied to large electric mining shovels at Cyprus Sierrita. The predictive program was initiated by Cyprus Sierrita and P&H Mining Equipment at the Cyprus Sierrita Mine in Tucson, Arizona during August of 1996 on the P&H model 2300 and 4100 electric shovels. The utilization of these technologies has shown the potential for improving electric mining shovel availability and minimizing maintenance costs. Predictive technologies provide the tools to assess machinery condition. Availability is enhanced by the condition based planning of component replacement. Maintenance costs are minimized by focusing resources through condition based prioritization.

Jan 1, 1997

By Joseph O. Cook

I know this is, at best, a frustrating period for the coal mining industry. About 20,000 miners have been laid off, mostly in the Appalachian and mid-western areas, and several mines are working less than 5 days a week; however, the industry is experiencing modern growth and, at least, there is the potential for future growth. The coal industry is probably only operating at about 80 percent of its present capacity, and it is certainly capable of helping this country solve its energy problems. Growth, as a rule, does not come easy, and growth in the coal industry is no exception to this rule. Many formidable challenges have to be overcome. As we all know, mining relies very heavily on the earth sciences, which have advanced significantly in the past few years, but we are always working in a changing environment which in most cases is a hostile environment. Large quantities of material are quickly extracted and rapidly moved in, generally speaking, a very confined area. The very nature of the mining business directly and constantly impacts our environment during this period in which the Nation and the world has become increasingly smaller and more concerned about protecting our environment. In addition, growth brings about an expanding work force which is increasingly younger and less experienced.

Jan 1, 1980

The Longwall Strata Control and Maintenance System (LoSCoMS) is designed to monitor shield pressures in real-time from longwall faces and to provide on-line information related to underground strata behavior and longwall mining operation. The information includes shield pressure data with statistical analysis of setting, developing and final pressures, prediction of shield pressures for the following shift or day, etc. and maintenance data on the shields. The LoSCoMS has been installed and tested at Shoal Creek Mine operated by Drummond Company, Inc. The system is providing valuable information to mine operators for better understanding of underground behaviors. As a result, it has become an effective tool for minimizing ground control hazards and reducing out of seam material.

Jan 1, 1997

By James F. McConnell

Federal and State sulfur oxide emission and ambient air quality regulations have been implemented to fulfill the requirements of the Federal Clean Air Act Amendments of 1970. Primary and secondary air quality standards have been established at levels considered necessary to assure the protection of the health and welfare of the public. Standards of performance under this Act have been established to control the rate of sulfur oxide emissions from individual sources so as to protect and to improve the quality of the Nation's air. The new source standards of performance were made rigorous for large coal burning stationary sources. This has had a severe impact on the electric utilities that operate the coal fired steam electric plants which are the largest consumers of the Nation's coal production. States have taken different approaches in State Implementation Plans (SIPS) as approved by the Federal Environmental Protection Agency. Some states, such as Pennsylvania, have chosen to permit moderate SO2 emission rates from existing sources which are not in critical air basins. All are required to meet primary and secondary air quality standards and to limit sulfur oxide emissions from new large stationary sources to a minimum of 1.2 LBS of S02/MMBTU fired. This re- quires a fuel sulfur percentage of about 0.7 for a 12,000 BTU/lb coal. In an effort to develop strategies and technologies to conform to performance standards while continuing and hopefully expanding the utilization of the Nation's coal supply, the electric utilities, the Federal and State regulatory agencies, and other industries and government agencies are considering several alternatives. 1. Natural low sulfur coal 2. Flue gas desulfurization - (FGD) non-regenerative and regenerative 3. Coal gasification 4. Liquefaction and solvent refined coal 5. Fluidized bed combustion 6. Chemical coal cleaning 7. Physical coal cleaning Of these options, only the first and the last can be considered to be widely used in full commercial practice at this time. FGD has certainly demonstrated technical and operating feasibility and is close to being in full commercial practice but it remains to be seen if the large systems under construction are economically and environmentally optimum.

Jan 1, 1975

By John J. Sammarco

Mining has one of the highest annual average fatality rates among major US industries. Health and safety dangers have been inherent to mining since the early days of picks and shovels. Even though miners’ health and safety has improved over the years, mining is still one of the most dangerous occupations. Mining was traditionally a low tech industry. It is now driven by competitive pressures to go high-tech by using programmable electronics (PE) for machine control, atmospheric monitoring and material processing. The industry’s experience with the functional safety of PE is limited compared with other industries. Thus, PE is an emerging technology for mining that can potentially create or worsen hazards.

Jan 1, 1999