Search Documents

By James Stewart

"THAT WHICH WE CANNOT SEE" INTRODUCTION Often it has been stated that the greatest of all fears is fear itself - fear created only by that which we cannot see or by that which we fail to understand. The elimination or minimization of fear can best be accomplished by a thorough understanding of the underlying causes of the fear. As related to the mining industry the omnipresent fear is the dread of acquiring cancer through accumulated exposure to "that which we cannot see" - radioactivity. The understanding of the resulting exposure effects can best be obtained through acquisition of authentic data and the subsequent analysis of the same by a group of highly qualified specialists. I may point out that the nuclear industry and its source, uranium mining, greatly surpass any other industries in the degree of public awareness as to its potential environmental effects. Public out-cry has always influenced major decisions relating to how industries conduct their operations and much of their effort has resulted in many changes. The issues of health and safety in the mining industry have created considerable public concern, but intense concern to those of us directly involved within the industry. Increasing concern regarding the effect of human activity on the quality of the outer environment of air, land, and water has developed within the past two decades. There is now a growing concern about the health and safety of persons at work in their inner environment, of their working-places in industry. Hearings and investigations conducted in Canada by three appointed "Royal Commissions" have all confirmed that this concern is well justified when focused on the health and safety of workers in our mines. REGULATORY CONTROL OF URANIUM MINING OPERATIONS In Canada, the ownership of mineral resources and the control of their extraction, except for uranium, is vested under the "British North America Act" in the provinces. In all provinces the statutory basis for health and safety provisions in the mining industry can be found in the provincial "Mining Acts" with each province assuming the responsibility to produce its own "Mining Act". In particular, all of the Mining Acts in Canada place upon the management of a mine the responsibility to ensure that provincial provisions are met. The "Federal Register" and mining companies parallel this arrangement in the United States. Equivalent legal

Jan 1, 1981

By Deborah Muggli

Minera Escondida is the world's largest copper mine. Its capacity is more than 800 kt/a (880,000 stpy) of copper. The Escondida open-pit mine operates at an elevation of 3,100 m (10,170 ft). It is located in the Atacama desert about 160 km (100 miles) southeast of the port of Antofagasta. At Coloso, 14 km (8 miles) south of Antofagasta, copper concentrate is dewatered by filtration for storage and shipment to overseas markets (Fig. 1). Concentrate filtrate water, after being treated to remove suspended solids, is discharged at 60 m (200 ft) depth into the Pacific Ocean. This effluent is free of particulates. However, it does contain metal levels above US Environmental Protection Agency (EPA) receiving water criterion. EPA standards are more strict than Chilean receiving water guidelines. However, a multiport diffuser provides rapid mixing of sea water with effluent to ensure metal levels in the receiving water remain below EPA receiving water guidelines. The Escondida Mine began operation in December 1990 at a rated mill capacity of 35 kt/d (38,500 stpd). Since then, the complex has since undergone three expansions. In 1996, it processed 115 kt/d (127,000 stpd) of ore. At Coloso in 1993, about 25% of the copper concentrate was fed to an ammonia leach plant for solvent extraction and electrowinng of cathode copper. This plant is designed to produce 80 kt/a (88,000 st/year) of cathode copper. In 1995, the ocean diffuser system's capacity was doubled to accommodate increased flows to a maximum 50 L/sec (793 gpm). This was achieved by extending the diffuser chamber by 32 m (105 ft) and adding 16 nozzles, which doubled the diffuser's capacity. In November 1996, Rescan Environmental Services began a field verification of the outfall/diffuser system's performance. The study's objective was to determine the performance of the outfall/diffuser system by measuring dilution factors using fluorescent Rhodamine dye and to determine if copper concentrations are below the US Environmental Protection Agency (EPA) water quality criterion of 2.9 µg/L total copper (EPA, 1986). Rhodamine dye was injected into the outfall/diffuser system. An oceanographic survey using an in situ fluorometer was conducted to measure dye concentrations in the effluent plume. Water column characteristics were also measured. These included current speed and direction.

Jan 1, 1997

By L. G. Stolarczyk, R. C. Fry

In coal-bearing formations, seams are often bounded by sedimentary layers of mudstone, claystone or shale. When the electrical conductivity of the surrounding sediment layers is greater than the conductivity of the seam, a natural parallel plate waveguide forms in the strata. For frequencies below the AM broadcast band, the waveguide can be used for the transmission of electromagnetic (EM) waves. In a uniform seam, the primary wave travels in the coal layer along paths between a radiating antenna and a distant receiving antenna. The travel distance increases with seam height and the conductivity of the surrounding sediment layers. The distance decreases with increased coal conductivity. In Cretaceous western bituminous coal, the distance may exceed 549 m (1800 ft). Anomalous geologic disturbance zones such as faults, shear zones, paleochannels, sills and dikes significantly alter the values of EM wave propagation constants (attenuation and phase) expected in a uniform seam. In the neighborhood of an anomaly, EM wave energy is scattered (reflected and diffracted). Scattering creates secondary waves in the seam wave guide. A receiving antenna at a remote location in the coal seam can be used to measure the magnitude and phase of the EM wave at the end of the path. The measured data can be processed to determine the average value of the propagation constants along each path. Paths with anomalous propagation constants are used to locate and image geologic disturbance zones. Radio Imaging Method (RIM) instrumentation, survey procedures and data processing (tomography) algorithms have been developed to image geologic structure in advance of mining. The survey is conducted between gate roads of a longwall panel. Data processing constructs contours of constant attenuation rate (phase constant) across the plan view of the panel. In anomalous zones, the contours rapidly change with distance. The shape of the contour lines generates a visual image of the anomaly and suggests the type of anomalous condition to be expected in the coal seam. This paper briefly discusses the depositional environment and the formation of the imperfect waveguide in coal-bearing strata. The linkage between sedimentary geology and EM wave theory establishes an understanding of how the propagation constants depend on the anomalous geologic conditions. A case study compares in-mine geologic mapping with the tomographic image of a longwall panel.

Jan 1, 1991

By Phillip R. Moyle

Voluminous deposits of commercial-grade phosphate occur in sedimentary strata in a 350,000 km2 (135,000 mi2) area of the middle Rocky Mountains of North America known as the Western Phosphate Field. The Permian marine strata that host the phosphate were deposited on the western margin of the North American craton and subsequently deformed, first by folding and thrust faulting of the Laramide orogeny, and then by Cenozoic Basin and Range block faulting. Carbonate fluorapatite is the primary phosphorus-bearing mineral. Organic matter is abundant in some strata, and both biogenic and non-biogenic pyrite are also present. Certain strata are enriched in several trace elements, especially in arsenic (As), cadmium (Cd), chromium (Cr), copper (Cu), molybdenum (Mo), selenium (Se), vanadium (V), uranium (U), and zinc (Zn). Phosphate has been mined from the Western Phosphate Field for nearly 100 years. Phosphate mining and processing constitutes the largest mineral industry of Idaho, producing more than $600 million in processed mineral value in 1997. Resource management agencies, phosphate producers, and others are concerned about the release of Se from phosphate mine wastes, especially at Maybe Canyon, and the potential effects that Se and other trace elements may have on the environment and on human health. U.S. Geological Survey (USGS) Mineral Resources Team scientists initiated a multidisciplinary study of the Permian Phosphoria Formation and related rocks in the south- eastern Idaho sector of the Western Phosphate Field in response to a request by the U.S. Bureau of Land Management (BLM). Studies to date reveal that Se is present in several phases, including native Se, and in an as yet unidentified form, possibly an organo-Se compound. Selenium is also present in pyrite and sphalerite. Selenium concentrations range from 1.2 to greater than 1,000 parts per million (ppm) in samples collected from exposures of the Meade Peak Phosphatic Shale Member of the Phosphoria Formation (Meade Peake) at Enoch Valley. The results suggest that Se concentrations vary spatially across strata and with depth, perhaps comparable to spatial variations of phosphate and organic carbon concentrations throughout the Western Phosphate Field demonstrated in previous studies. Some Se-enriched strata may be of adequate dimension to allow selective extraction during mining. Such units could be handled separately from the main ore process or waste streams and isolated in order to reduce the potential for release of Se to the environment

Jan 1, 2001

By Robert W. Lawson

INTRODUCTION Prior to 1705, underground mining was limited to mineral deposits located above or a very small distance below the water table. The development of the steamdriven mining pump was motivated by the need to extract minerals from deposits considerably lower than the water table. Today, the majority of mine pumps are driven by electric motors, although some small utility pumps are driven by compressed air. Of the numerous types of pumps that might be applied to mine service, the two types used most frequently underground are the centrifugal and plunger pumps. Each of these types has its proper application. In most instances, plunger pumps are best for handling low water volumes against high heads, while centrifugal pumps effectively handle either low or high water volumes against low heads or high water volumes against high heads. This chapter describes pumps applied to underground mine service, where the mine service consists of mine drainage (removing mine water as it accumulates), mine dewatering (removing water from a flooded mine), and pumping for special applications such as hydraulic mining and hydraulic hoisting. CENTRIFUGAL AND PLUNGER PUMPS Modern mine pumps are classified as either centrifugal (kinetic) or plunger (positive-displacement) pumps. The following paragraphs describe each of these classifications. Centrifugal Pumps Centrifugal pumps may be grouped into various types, depending upon their various features: Number of Stages: In a single-stage pump, the total head is developed by one impeller, while a multi¬stage pump utilizes two or more impellers acting in one casing to develop the total head. Fig. I shows a cutaway view of a single-stage horizontal split-case double -section centrifugal pump. Fig. 2 shows a cutaway view of a six-stage medium-pressure split-case diffuser-type centrifugal pump. Type of Casing: A volute pump has a casing in the form of a spiral or volute. A circular-casing pump has a casing of constant cross section concentric with the impeller. A diffuser pump is equipped with a diffuser that converts velocity head to pressure head. Shaft Position: A horizontal pump normally has the shaft in a horizontal position, while a vertical pump normally has the shaft in a vertical position. Fig. 3 illustrates a vertical turbine-type slurry pump. Suction: A single-suction pump equips the first stage with a single-suction impeller, with fluid entering the impeller on only one side. A double-suction pump equips

Jan 1, 1982

By Andrew Cho, Changsoo (Kevin) Moon, Richard Flanagan, Brian Larsen

"INTRODUCTION Project Background The U.S. Army Corps of Engineers (USACE)/Port Authority of New York & New Jersey (PANYNJ), as part of their New York and New Jersey Harbor Deepening Project, will dredge this shipping channel to a depth of 16.5 m below mean low water (MLW). By deepening the channel, the new generation of larger, “post-panamax” container ships coming to U.S. waters as a result of the expansion of Panama Canal can be accommodated in local marine terminals, helping to retain the nearly 300,000 jobs and $12 billion in annual wages the PANYNJ provides to the region. The existing siphons are situated at a depth that could be compromised by the planned dredging of the channel (nycedc.com). The purpose of this project is to build a new 1.83 m diameter water main inside a 3.66m diameter tunnel replacing the two existing siphons in order to provide the necessary backup water supply to Staten Island across the Anchorage Channel within the Upper New York Bay from Brooklyn. The proposed tunnel is approximately 2.9 km long and at a depth of at least 26 m below MLW. The project is funded jointly by New York City’s Department of Environmental Protection (NYCDEP) and PANYNJ and is managed by New York City Economic Development Corporation (NYCEDC). The contractor of the project is Tully/OHL JV, the designer is CDM/HMM JV, and the CM is LiRo/PB JV. History of New York City’s Soft Ground Tunneling The New York City area has a relatively long history of soft ground tunneling, commencing in the late 19th century. Construction of the first Hudson River tunnel crossings was begun (but not completed) in 1874 for the Hudson & Manhattan Railroad using compressed air supplying a shield. The work continued intermittently until the project finally opened for service in 1907. These 1.72km long tunnels (maximum depths of 29 m) are still in operation and now operated as the PATH Tunnels. They are approximately 5.5m diameter utilizing cast iron segments. The river bed consisted of primarily silt with shallow rock near the New York side. Air “leaks” occurred during the compressed air excavations resulting in some serious “blows” with water and soil entering the tunnel, including one incident with 20 deaths."

Jan 1, 2016

By Christine E. Turner-Peterson

Pore-filling organic material concentrated uranium to form sandstone-hosted primary uranium deposits in the Jurassic Morrison Formation of the Grants uranium region, New Mexico. Petrographic observations and radiometric ages for primary ore in the Westwater Canyon Member require that the organic material was emplaced early in the diagenetic history of the host sandstone; in fact, organic material was emplaced before major compaction. This inferred early emplacement constrains models concerning the nature and origin of the organic material and thus also constrains models of ore genesis. Reconstruction of the burial history of the basin indicates that Late Jurassic-Early Cretaceous time, the interval of inferred emplacement of the organic material, was probably not a time of hydrocarbon generation and migration. Nuclear magnetic resonance analyses, elemental abundances, and isotopic studies provide further constraints on the nature of the organic material, and data from these studies are consistent with a humic acid rather than an oil origin. In addition, the overall tabular shape of primary uranium orebodies and the way these orebodies are suspended in the host sandstone mimics Recent deposits of humate, the precipitated form of humic acids. The critical clue that favors a humic acid origin for ore-related organic material is provided by the nature and patterns of postdepositional alterations that are spatially and temporally related to primary ore, specifically destruction of detrital magnetite and ilmenite (iron-titanium oxide) grains. Humic acids are implicated in the destruction of iron-titanium oxide grains because these organic acids are one of the most effective natural agents in leaching of Iron from these grains. Thus, timing constraints, chemical evidence, orebody geometry, and the nature and patterns of ore-related alterations favor a humic acid origin and suggest that an oil origin is highly unlikely. Because alteration of iron-titanium oxide grains tracks the pathways of humic-bearing solutions through the host sandstones, it is possible to trace these solutions back to their source. Alteration patterns in the Westwater Canyon Member suggest that the humic-bearing solutions originated as pore fluids in the mudflat facies of the overlying Brushy Basin Member and moved into adjacent sandstones during early dewatering of the mudstones. The humic acids precipitated, by the process of cation loading, in tabular layers. Uranium was concentrated within these tabular layers by complexation with the humic acids to form primary uranium orebodies.

Jan 1, 2013

By William G. Kegel

Apart from a usable product and good 'mining conditions, the greatest asset for a profitable coal mining organization is an effective mine maintenance program. The first step in achieving this is to have good mechanics-or men who want to be mechanics and are interested in knowing more about the design and control of the machines in their charge. A good mechanic's knowledge and ability result from ambition, curiosity, and determination. Starting with these qualities, the aspiring mechanic can launch his career by learning all he can about mechanics, electricity, and hydraulics. Though the path is rough, the end result is rewarding. Mining machinery probably receives as much, if not more, abuse as any other heavy equipment in use today. Considering the conditions under which much of the repair work must be done, it is essential that the mine operator has the best men and tools to perform the work. Mining machines, from their inception, have utilized the electric motor; and down through the years of mechanization, this power source has undergone many changes to better adapt it to the job. The first motors used were direct-current (d-c) motors since d-c power was the most economical power source for mining at the time of early mechanization. These motors were large open-type machines which are seldom used in modern mining. Because of the mine environment, the d-c motor has been reduced in size to better suit the application in mining machines and is now manufactured with dust-tight or explosion-proof enclosures. The d-c motor is constructed with either (or both) series and shunt fields located on the stationary part of the motor (stator) and- an armature coil wound on the rotating part of the motor (rotor). Power is supplied to the armature by brushes which are held stationary and make sliding contact with the armature. The brushes requires regular and careful maintenance because worn or defective brushes will cause heat or arcing which can destroy the motor. D-c motors can be used as d-c generators when mechanical power is supplied to them by the rotating shaft. In the case of a locomotive, this principle is used in dynamic braking. The momentum of the locomotive drives the motor and generates d-c power. The power is regulated with resistors and provides opposition to the motion of the locomotive.

Jan 1, 1981

By S. G. Malghan, J. P. Van Dillen

Introduction Some uranium minerals are paramagnetic and hence are amenable to concentration by high gradient magnetic separation (HGMS). This paper describes effects of the HGMS parameters-pulp velocity, field strength, matrix loading, and magnetic field gradient-on the product recovery and grade. Unsatisfactory separation of uranium minerals by HGMS is related to ore-specific properties, such as lack of liberation, fine dissemination of uranium minerals, uniform distribution of magnetic minerals throughout the ore matrix, and interference of fine-sized slimes. Experimental techniques to identify and resolve some of these problems are outlined. HGMS of Uranium Ores The mechanism by which uranium minerals are attracted to a magnetic field is either due to its magnetic susceptibility or its association with other minerals that are magnetic. Data on magnetic susceptibility of uranium minerals are scarce. The only reported data are for uraninite at 2360 X 10-6 cm3/mole. Povarennykh (Andres, 1976) concluded that the magnetic properties of minerals depend on: • Structure of the outer electron shell in a mineral with electropositive atoms; • Valence of the atoms; • State of the chemical bonds; • Type of coordination; and • Proportion of magnetic atoms (Fe, Mn, Cr, and Ni) in the composition of the mineral. However, information on the magnetic susceptibilities of the constituent atoms of a mineral alone does not suffice for evaluating the mineral compound as a whole. Most often, uranium minerals can be beneficiated by HGMS if they are associated with other minerals that are magnetic. This appears to be a more predominant mechanism by which the uranium minerals are beneficiated. Experimental A Sala-HGMS (Malghan and Subramanian, 1981), model 10-15-20, separator was used in the experiments. The matrix material-ferromagnetic stainless steel in the form of expanded metal or steel wool-was packed into a 38-mm (1.5-in.) diameter by 360-mm (14-in.) long canister. The matrix material occupied only a 150-mm (6-in.) length. The experimental set-up and slurry flow direction are described elsewhere (lannicelli, 1976). The response of uranium ores in the HGMS was studied by feeding well-dispersed slurry at 10% solids and examining the influence of process variables on selectivity and overall uranium recovery. The chemical and mineralogical characteristics of the ores under study are presented in Table 1.

Jan 12, 1983

By Aki Fujii, Hiroshi Dobashi, Mitsuro Matsuda, Yoshinari Kondo

INTRODUCTION The Metropolitan Expressway Central Circular Route with a total length of approximately 47 km is located outside the Inner Circular Route of Tokyo (at a radius of approximately 8 km from the city center). Sections with a length of approximately26 km, slightly less than 60% of the total length, on the east and north sides are in ser-vice. Completing the Central Circular Route (Figure 1) is expected to enable through traffic concentrated at the city center to get around, and to form a well balanced trans-port network, which will alleviate traffic congestion considerably. The Central Circular Shinjuku Route, a section with a length of approximately 11 km on the west side, is now being constructed at a fast pace. The route is being built mainly by the shield tunneling method to carry out work smoothly under a trunk highway carrying heavy traffic and to reduce adverse effects of tunneling work on residents in the neighborhood. Shield tunnels have recently been becoming longer and deeper, and no secondary linings have been used in an increasing number of cases because of the over-crowding of cities or the reduction of budgets for public works. Economical, durable and high-quality segments have been required for linings of shield tunnels. Segments are made of concrete, steel, cast iron or combination thereof. Concrete segments are generally used in shield tunnels of medium to large diameter. Concrete segments are highly durable and resistant to compression, so they are highly resistant to earth pres-sure, water pressure and jack thrust. They are, however, heavy and have low tensile strength, so they are brittle and their corners are likely to spall. Concrete segments should therefore be handled carefully.[1] The authors have developed a steel fiber reinforced highly flowable concrete segment (referred as SFRC segment) that overcomes the weaknesses of concrete segments[2] to construct economical, durable and high-quality linings. SFRC segments have been applied to outbound sections SJ51 through SJ53 of the Central Circular Shinjuku Route. Unlike conventional concrete segments (referred as conventional RC segments), SFRC segments are made of steel fiber reinforced self-compacting highly flowable concrete. SFRC segments require less reinforcing bars than conventional RC segments because steel fibers are expected to work as reinforcements. Steel fiber reinforced concrete is a composite material that overcomes the brittleness of plain concrete, and has higher resistance to bending, tension and shear than

Jan 1, 2007

By Michelle L. Ramos

INTRODUCTION The Ballard Siphon was built in 1935 and consists of two 91.4 cm (36-inch) diameter wood-stave pipes. These pipes convey sewer flowsunder the Ship Canal from northwest Seattle and the Ballard Regulator to the North Interceptor and the West Point Treatment plant. The siphons were constructed using open cut construction, are now buried in the sediment on the floor of the canal, and have severely limited ability to be dewatered, inspected, or cleaned. The existing siphon is 394.7 m (1,295 feet) long from the junction structure on the southern shoreline to the regulator structure on the north. The location of the Ballard Siphon is shown in Figures 1 and 2. The area around the Ballard Siphon has become more populated and developed since the siphon was built. Additionally, the Ballard Siphon is subject to high flows that are greater than the capacity of the pipelines. This has resulted in predict-able Combined Sewer Overflows(CSO?s) whenever a large, long duration rain event occurs. The aged pipeline of uncertain viability has become a critical piece of the sewer system infrastructure. Because of the age of the pipelines and their importance, a sonar survey was completed on both barrels of the Ballard Siphon in December of 2005. The sonar images appeared to indicate crown intrusion of the wood-stave pipes, which suggested that the pipes were in imminent danger of collapse. As a result, an Emergency Declaration was executed by King County and the Ballard Siphon Replacement Project was initiated. Staheli Trenchless Consultants was retained to perform feasibility studies to deter-mine the viability of using microtunneling and horizontal directional drilling (HDD) for replacement of the Ballard Siphon. For the evaluations, the preferred site location was determined to be at or near the site of the existing Ballard Siphon in order to minimize the ancillary sewer work which would accompany moving to a new site. To meet flow demands and hydraulic requirements, the replacement siphon needed a mini-mum equivalent diameter of 182.9 cm (72 inches). This could be accomplished with a number of different siphon diameters and configurations including, but not limited to, three 106.7 cm (42-inch) diameter pipelines, two 152.4 cm (60-inch) pipelines, or two 91.44 cm (36-inch) pipelines and a 121.9 cm (48-inch) pipeline.

By Y. J. Wang

The selection of a shaft size for ventilation purposes is a classic problem of concern to mining engineers. This presentation is concerned with the sizing of conventionally-sunk circular shafts with concrete or shotcrete linings. Costs of sinking shafts of three different depths (from 500 feet to 1000 feet) and six different diameters (from 14 feet to 24 feet) were obtained through questionnaires to shaft contractors. The primary objective of the economic model presented is the balancing of detailed annual capital and operating costs to achieve the minimum overall cost of the shaft installation over its life. The economic model is similar to previous analyses but treats several of the individual cost categories in an updated fashion. Included in the paper is a detailed analysis of the effects of varying power costs on optimal shaft size. Also included are a statistical analysis of current shaft costs and comments on the choice between shotcrete and concrete linings.

Jan 1, 1977

The roasting process of copper concentrates containing variable quantities of arsenic in a fluidized bed regime was analyzed, considering the technical literature published on the topic in the last quarter century. Although emphasis has been given to the analysis in the fluidized bed regime, other processes have also been considered, under a reducing, neutral or oxidizing atmosphere. The kinetic mechanisms of roasting, as well as the models that have been applied or those likely to be used to explain the kinetics of arsenic removal, are analyzed. Regarding the kinetic mechanisms, those that have been applied to copper concentrates with both high and low arsenic content are included. The roasting kinetic model includes the kinetic data analysis techniques, general models, equations and an estimation of the conversion degree through dynamic, differential and integral methods, as well as particular models for mineralogical components, such as smelter dust and copper concentrates with low and high arsenic content.

May 1, 2012

By B. Qiu, Y. Luo

Longwall and/or room-and-pillar mining operations in multiple coal seams may not only induce subsurface and surface subsidence but also cause interactions between these mined coal seams. The interaction might destabilize underground mine structures and subsequently induce additional strata movements. Mathematical models to use the predicted subsurface deformations to assess the interactions and the consequences have been developed. The models are incorporated into a computer program, CISPM-MS, for predicting the final surface movements and deformations, as well as the mining interactions associated with multiseam coal mining operations. It predicts final surface movements and deformations caused by the individual mining operations and by the interactive effects. The program can also be used to assess mine structural stability in multiseam mining operations. The paper presents the developed interaction models and their application in surface subsidence prediction caused by multiseam mining operations. A case study involving mining in two coal seams, using longwall and room-and-pillar mining methods, respectively, will be used to validate the program.

Jan 1, 2013

By G. L. Mowrey

One critical element of the U.S. Bureau of Mines (Bureau) autonomous mining research program is the development of a reliable coal interface detection (CID) system. Several candidate CID concepts currently being investigated by the Bureau include vibration, passive infrared, radar, and natural gamma radiation (NGR). To establish which CID sensor technologies need to be developed for a given seam, coal and adjacent rock samples (i.e., immediate roof and floor) are being collected from selected major coal seams in the U.S. and are being analyzed in terms of NGR and other geophysical measurements. Results of the NGR measurements indicate that, in general, all shale and shale-like materials (e.g., drawslate, slate, and fireclay) have higher NGR readings than the coal seam. Consequently the NGR method appears to be a potentially useful CID tool, provided that the immediate roof and floor are both composed of a high percentage of shale-type material.

Jan 1, 1990

By W. J. Miles

Diatomaceous earth or diatomite is a sedimentary rock of organic origin that is composed principally of the silicious skeletal remains of diatoms. Diatoms are microscopic single cell acquatic plants that are related to algae. Diatoms first became abundant in the Cretaceous period from about 65 to 135 million years ago. Most of the commercial deposits are of Pliocene through recent age, and are younger than 35 million years. Diatoms are still abundant in present day lakes and seas. The living diatom is supported and protected by two half cell walls or valves united by a connecting band or girdle. These valves are composed of opaline silica extracted from the water in which the diatom lives. After death of the diatom, the silicious remains settle in the lake or sea and accumulate at variable rates approaching several millimeters per year for very active diatom colonies. This accumulation of silicious sediments, after decay of the organism, burial, and uplift, can result in the formation of diatomaceous earth deposits.

Jan 1, 1987

By Yi Luo

Subsurface strata movements and deformations caused by longwall mining operations in underground coal mines could affect many important coal mining activities, such as gob well degasification, ground water protection and multiple seam mining. The stratifications in the overburden have significant influence on the subsurface and surface movements and deformations in the ground subsidence process. An enhanced subsurface subsidence prediction model considering overburden stratifications has been introduced in this paper. In this method, the entire overburden strata are equally divided into a finite number of layers and the percent of the hard rocks in each layer is an additional input. The proven influence function method is applied to predict the subsidence on each of the predefined layers progressively upward using the predicted subsidence on the previous layer as the subsidence cause for the current layer. A computer program is developed to facilitate the calculations. A case demonstration is used to show the applicability of the proposed subsurface subsidence prediction model.

Jan 1, 2012

By R. H. Weiland

The dewatering of flocculated clay suspensions by compression in a centrifugal field has been investigated. The results are evaluated with regard to both direct applicability to centrifugal dewatering, in solid-bowl centrifuges for example, and indirect applications to gravity sedimentation systems. It is well known that sediment consolidation under gravity depends on structural characteristics such as permeability and on the "self-weight" of overlying sediment layers. An important objective of the study has been to evaluate the self-weight effect using centrifugal forces to simulate consolidation in deep sediments. In this way, small-scale laboratory tests can be used to predict the rates and limits of sediment compression in industrial systems such as thickeners and settling ponds. Experiments have been conducted in which the sediment mass and initial structure were maintained constant while the effective sediment weight was varied by centrifuging at different speeds. The effects of initial structure have also been studied using controlled variations in flocculation conditions.

Jan 1, 1993

By A. B. Cortes

This research work discusses the development of a two-dimensional model that represents the flow that occurs in the inlet section of hydrocyclones. The governing equations are the two-dimensional, unsteady, incompressible Navier-Stokes equations in cylindrical polar coordinates with primitive variable formulations. In this approach, no assumptions have been made other than independence in the axial direction. The full two-dimensional Navier-Stokes equation in the r-a plane is used. The commonly used simplifying assumption of axisymmetry is not used. A numerical technique based on a newly developed spectral-difference method is used to solve the equations. The spectral-difference method is a multi-domain, and multi-dimensional extension of the Jacobi polynomial collocation technique. The computational grid for the inlet section is composed of 25 sub-domains which result from five partitions in the angular direction and five partitions in the radial direction. Several test cases are used to validate the appropriateness of the numerical model.

Jan 1, 1995

By J. R. Dyni

The lacustrine Green River Formation of Eocene age in the Green River Basin, southwest Wyoming, contains the world's large resource of natural sodium carbonate in bedded trona (Na2CO3? NaHCO3? 2H2O). In this study, 126 billion tons are estimated to be present in 22 beds, ranging from 4 to 36 feet in thickness. These 22 beds underlie areas of about 50 to more than 775 square miles at depths ranging from about 650 to more than 3,000 feet below the surface. The total resource of trona ore in the basin for which drilling information is available is estimated to be about 149 billion short tons. The undeveloped deeper trona beds in the southern part of the basin may be exploitable by solution mining. Additional unevaluated sodium carbonate resources are present in disseminated shortite in strata interbedded with the trona and in shallow sodium carbonate brines in the northeast part of the basin.

Jan 1, 1995