Search Documents

By M. W. Harmer

Laboratory test work, pilot plant testing and plant experience with wet, fine mesh screens is discussed. High frequency, low amplitude, fine mesh, wet screens were installed on the 6th cleaner concentrate stream. These screens produce a 60% oversize recovery split of the molybdenite concentrate that is of leached equivalent quality. The undersize stream is leached with 'hot ferric chloride to remove Pb and Cu contaminates before roasting or shipment to sulfide customers. This plant modification is a good example of using existing technology in an unconventional flow sheet to yield significant cost savings.

Jan 1, 1990

By G. T. Lineberry

Reduced clearance is one of the most important characteristics of encumbered space in underground coal mining. Another key variable is the maximum velocity at which a piece of mobile mining equipment can operate in this limited space. Typical velocity- clearance curves for different mine transportation systems are developed and characterized. Applications of the relationships are examined, emphasizing their significance in the design and control of mine materials handling systems.

Jan 1, 1983

By S. L. de Moraes

This study aimed to identify a way to reduce the use of bentonite in the pelletization of magnetite. With this goal, different combinations of binders were compared to bentonite by examining the quality of pellets obtained by balling drum agglomeration. Pellets were subjected to routine tests that included simple compression of the wet and dry 105°C pellets, dropping wet pellets to determine their ability to survive handling and submitting pellets to thermal shock to determine how they tolerate drying and preheating. The best results use sodium silicate (1.5%) as a binder and show that it is possible to pelletize iron ore without using bentonite.

Jan 1, 2010

As the 2009 George Fox Conference neared its conclusion, Arthur Silber, project chief of the Mass Transit Tunnel (MTT) project was able to pull away from the constant buzzing of his Blackberry long enough to give a short presentation and a significant piece of news to the record 318 attendees at the Graduate Center, City University of New York regarding the MTT project. ?As the former administration (The Bush administration) was leaving office, we were told that Congress was notified of the FTA?a (Federal Transit Authority?s) intent to issue final design construction approval to us,? Silber said of recent advancements concerning the $7.2-billion dollar project. It will add passenger rail service from New Jersey to New York City as part of the Access to the Region?s Core project in the form of the Trans Hudson Express Tunnel (THE tunnel). ?That 10-day waiting period ended yesterday (Jan. 26).? In days leading up the Fox Conference, those involved in the tunneling industry, and the MTT in particular, had a lot to be optimistic about. The MTT received environ-mental approval on Jan. 14 (see page 9) and, with the acceptance of the final design, the multi-billion dollar project moved that much closer to a ground-breaking ceremony. So close, in fact, that before leaving his office for the conference, Silber posted the contract documents and plans for the Manhattan Tunnel project online at www.arctunnel.com (an indepth look at the project from Silber is on page 22). While many were interested in the progress of the project, Silber also spoke about the new plans for the cavern complex at the New York Penn Station expansion. The original plans called for two lines that would come into a large cavern complex with a north and south cavern to access the trains. After numerous core samples were taken from the streets of Manhattan, it was deter-mined that this design was not feasible and changes were made that will include a deeper cavern under Sixth Avenue, with 14-m (45-ft) of cover with a 30-m (96-ft) wide cavern that resides entirely under 34th Street. The cavern was also moved 20 m (60 ft) to the west to remain at least 61 m (200 ft) away from New York City Water Tunnel #1. The new design will include three-over-three track arrangement. The mezzanine will be 46 m (150 ft) below street level at 8th Ave, Silber said.

Jan 1, 2009

By Deepak Malhotra

This paper discusses the need for periodic auditing of mineral processing flowsheets and the potential benefits a company can gain from a study of this nature. A carefully designed flowsheet auditing can have a significant impact on the metallurgical performance in the plant. Several case studies illustrating the potential benefits that can be attained from flowsheet auditing of mineral processing plants are discussed.

Jan 1, 1986

By Raúl Castro, Marco Vera, Alfonso Ovalle

The underground mining evolution for block cave mines in Chile and worldwide has made important strides in the last decades. Nonetheless, reserves determination in the initial stages of these types of projects—mainly for long-term planning—is not studied in as much detail as it should be, especially regarding the impact on the final value of the enterprise. Today, the first estimation of the size of a block cave mine, typically expressed in tons, tends to determine very large footprints and ore bodies. The resulting large-scale mine is obtained by applying the marginal cut-off grade (COG) to determine reserves. Yet, in many cases, it is possible to obtain an equal or higher benefit, extracting fewer reserves in less time, with a smaller active area, which significantly reduces the project’s uncertainty. To explore scenarios obtained by applying a higher marginal COG in the initial phases of the project, the Hill of Value methodology is used to estimate the net present value (NPV) in relation to the production rate and the COG. However, the application of this methodology considers certain simplifications that generate results which are not completely satisfactory in specific cases. This paper suggests an improvement of this method to obtain more reliable results regarding determination of a COG profile that will optimize the NPVof a block-cave project. The methodology was developed and applied in a massive polymetallic deposit with zinc, lead, and silver mineralization, corresponding to a real block caving project. The methodology provides NPV results that differ by approximately 15% in comparison to the real mine plan, while also being considerably simpler and faster to calculate. In summary, the proposed methodology provides a reasonable and fast procedure to estimate higher than marginal COG that increases the NPV of block cave mine projects.

By R. Grandori, L. Pellegrini

The construction of the La Joya hydropower plant (Costa Rica) was awarded by the Spanish power company, Union Fenosa, to the Italian Joint Venture formed by the companies SELI SpA and Ghella SpA. The project, located in a mountainous region of central Costa Rica, includes a 7.9-km-long head race tunnel having an excavation diameter of 6.18 m. A double-shielded TBM was selected to perform the tunnel excavation, which involved mainly volcanic rocks in variable but generally very weak conditions. The tunnel crossed long and continuous sections in completely weathered rock masses with no residual cohesion and with high water inflows. The paper describes and analyzes: The special methods adopted to overcome these sections with the TBM includ-ing face stabilization by chemical grout and foams as well small by-pass tunnels in the crown combined with TBM advance/support The grouting design and the grouting method that was implemented to meet the waterproof design specifications and restore the original groundwater level in the mountain The additional geological investigations performed to improve the knowledge of the rock mass in front of the TBM and the outcomes of these investigations The performance of the TBM in different ground conditions and on average along the entire tunnel Finally, the author’s comment about the possibility of implementing and improving the technologies experimented with in this project in future similar applications.

Jan 1, 2007

By J. W. Shield

Refractory sulfide flotation or gravity gold concentrates are coated onto a sized support matrix and placed in a heap configuration for biooxidation. The surface coating is typically less than 0.05 in. thick and the support matrix is preferably composed of 0.375 to 0.75 in. diameter material. The exposed thin coating of sulfides reduces biooxidation rate limitations due to oxygen mass transfer. The large spaces between matrix particles reduce resistance to fluid percolation and aeration in the heap. The capital and operating costs for this biooxidation configuration are significantly less than for concentrate biooxidation in stirred tanks. After 30 to 90 days of biooxidation, sub- sequent gold recoveries exceed those seen in whole ore heap biooxidation and are comparable to recoveries obtained from stirred tank biooxidation processes. Results from laboratory and pilot testing indicate that this technology is a viable alternative for pretreating sulfide refractory gold ores.

Jan 1, 1997

By A. Suarez, M. Menendez, M. R. Gent, P. Riesgo

"Recent requirements to reduce thermal coal plant emissions, and ultrafine coal's tendency to produce these emissions due to its typically high ash and moisture contents have limited the use of ultrafine coal. Ultrafine coal in beneficiation plants are usually either disposed of in tailing ponds at a loss in combustible material or disposed of by blending with coarser higher-grade products, resulting in a reduction in marketed product quality. A study of the options for processing ultrafine coal, consisting of < 200 µm hydrocyclone overflow, with 38.8 percent ash content is presented here. Ultrafine coal was processed based on 200-µm sieve bend and 10-µm hydrocyclone classifications, enhanced gravity separation (EGS) and froth flotation concentration as well as combinations of these. Yield, combustible material recovery (CMR) and product humidity were evaluated as test results.Depending on the processing applied, product ash content could be reduced up to 49.7 percent, and up to 95.8 percent CMR of the actual run of mill feed could be attained. All of the processing options analyzed could reduce produced thermal electric plant emissions due to ash and moisture from 22 to 38 percent of the actual unprocessed ultrafine coal product.Froth flotation was found to be the optimal process, yielding a product with the lowest ash content attained of 19.5 percent and CMR of 92.3 percent. Being the most versatile of the processes evaluated, it is capable of producing coal with varied ash contents but is subject to potential variations in coal flotability. The most complicated of the processing options, a combined sieve bend recovery of the > 200 µm fraction and EGS processing of the 10 to 200 µm fraction was found to be the next best option, attaining a combined 90.1 percent CMR and 25.0 percent ash content. IntroductionMunicipal, regional and national objectives to reduce fossil fuel combustion emissions and their effects on air quality and global weather changes are affecting thermal electric plant operations. Plans and regulations such as President Obama's Clean Power Plan (U.S. Environmental Protection Agency, 2015), the European Directive 2010/75/EU (European Commission, 2010) and China’s proposed Enhanced Actions on Climate Change (Wei, 2015) are of major significance to thermal electric plant operations. Although thermal plant efficiencies depend in large part on the losses of heat by plant components, the ash and humidity contents of thermal coal invariably reduce plant efficiencies and increase emissions of carbon dioxide (CO2), nitrogen oxides (NOx) and dust.Any noncombustible material present in thermal coal will result in higher CO2 emissions per unit of energy produced. Since no particle emission control can be totally effective, it is to be anticipated that any reduction in coal ash content will also result in reduced particle emissions. Kurose, Ikeda and Makino (2001) reported that NOx emissions also increase with coal ash content. The effect of coal moisture content during combustion is complex. Kurose, Ikeda and Makino (2001) showed that an increase in coal moisture content significantly reduces thermal NOx to total NOx production, and Bosoaga et al. (2006) showed that it tends to reduce NOx emissions. Since the humidity, pyrite and ash content of thermal coals directly affect thermal electric plant efficiencies and emissions, minimizing these factors should facilitate, at least in part, compliance with thermal electric plant emission limits. This, in turn, would affect the specifications and prices of the coal preparation plant products."

Jan 1, 2016

By L. M. Gochioco

The Seismic Interactive Interpretation Workstation (S//W) provides a wide spectrum of utilities ranging from improving field acquisition techniques, data processing and interpretation of coal seismic data. The power of the workstation lies in the interpretation process where various sets of geophysical and geological data are integrated to form a network of information that is stored in a database. Computer models are generated from known borehole and geologic information and later cross-correlated with the processed seismic data. Structural and stratigraphic modeling techniques add another dimension to the interpretation process. Complex trace attributes highlight subtle features not easily observed in black and white sections. Using the computer workstation, the explorationist gains valuable insight and conducts more intelligent interpretation of seismic data through a more comprehensive network of data analysis.

Jan 1, 1992

By J. Hazen, R. Jenner

This project was developed at the PCS Phosphate Mine in Aurora, NC. This site includes a surface mining operation, beneficiation plant and chemical processing facility located in the coastal plain of eastern North Carolina. The phosphate ore being mined at this operation is a 10 to 12 meter (35 to 40 foot) thick colloidal deposit located approximately 30 meters (100 feet) below the ground surface. The ore is pumped to the beneficiation facility where it is separated into clay, sand and concentrate streams. The concentrate product is utilized at the chemical plants to produce a wide range of products including fertilizer, industrial phosphates and animal feed products. The Cyclone Dike Builder (CDB) project developed a technique for dewatering the beneficiation tailing sand stream and providing innovative placement for dike construction. Future material balance requirements at the PCS Phosphate mine required an improvement in tailing sand placement technique to accomplish strategic objectives. The water volume of the sand slurry forces significant quantities of sand out of the dike profile during deposition. PCS Phosphate and MetPro Supply of Florida developed a mobile high-density hydro-cyclone station to remove most of the water and significantly increase the density of the sand being placed for dike construction. This high-density sand slurry is then effectively controlled using minimal heavy equipment operation.

Jan 1, 2004

By M. K. Buder

Over the years, electric utilities have been faced with declining steam-coal quality, rising coal prices, and increasingly rigid and costly environmental standards. As a result, many utilities are beginning to show an interest in coal cleaning to upgrade coal by improving its heating value and reducing its sulfur content. Among the primary questions that must be answered for these electric utilities is whether the cost of coal cleaning can be offset by the potential cost savings in coal transportation and utilization in power generation. In search of at least a preliminary answer to this question, the Electric Power Research Institute (EPRI) engaged Bechtel to perform a case-by-case economic study to examine the cost effects of using cleaned versus raw coal to fuel new electric power plants. The results of two of the seven cases studied which involved western coals - one from Montana and another from Utah - are reported in this paper. Coal cleaning appeared to be a cost effective option for the Utah coal, but only marginally economical for the Montana coal. These cost results are expected to change to favor coal cleaning to a greater extent with the application of the final revised New Source Performance Standards regulating SO2 emissions just issued by the EPA. The study was based on the regulation originally proposed by the EPA under the 1977 Clean Air Act Amendments.

Jan 1, 1979

By D. L. Misterek, E. J. Slebir, G. W. Ring, M. A. Laird

INTRODUCTION In 1973, the Federal Highway Administration (FHWA) initiated a 10-year program of research on tunneling technology for future highways as a part of a larger Department of Transportation effort on tunnels. The objectives of the FHWA program are to: improve tunnel design technology, reduce costs, minimize adverse environmental impact due to construction, increase the rate of construction, and assure the maintenance of a safe and attractive tunnel environment. The program is divided into four research tasks designed to solve tunneling problems identified by the engineering and field offices of the FHWA. These tasks are as follows: 1. Cut-and-Cover Tunneling 2. Site Investigations 3. Ground Movements - Prediction and Control 4. Highway Environmental Criteria for Tunnels In order to provide input into Tasks 2 and 3, the FHWA is sponsoring an investigation and testing program by the U.S. Bureau of Reclamation to instrument and monitor two sites in the second bore of the Eisenhower Memorial Tunnel located on Interstate Highway 70 at Loveland Pass approximately 97 km (60 miles) west of Denver, Colorado. The tunnel will be approximately 14.0 m (46 ft) in diameter when excavated. The study is designed to generate data on: (1) changes in the state of stress, and movements during and after tunneling, (2) tunnel lining design requirements, (3) developing a

Jan 1, 1976

By Richard R. Klimpel

In this paper, the old and the new commercially available reagent chemistries for the improved flotation of sulfide minerals will be summarized. The reagent classes discussed are those that meet three criteria: 1) they are being commercially used and/or large scale plant tested in North America in the last few years; 2) they are clearly different in chemical structure than commonly used commercial reagents of the last few decades and are not simply mixtures of existing reagents and/or simple changes in cation, alkyl group size, etc. and 3) the structural formulae are clearly specified in the public literature.

Jan 1, 1994

By J. A. Marshall

"INTRODUCTION The purpose of this paper is to investigate the potential for use of UAVs in underground mines and present a prototype design for a novel autorotating UAV platform for underground 3D data collection. The mining industry has recently shown increased interest in the use of unmanned aerial vehicles (UAVs) to assist in everyday operations [20, 11, 4]. Above ground, small UAVs are in some cases a more efficient, inexpensive, and safer alternative to manned aircrafts currently used for photography, inspection and security [6, 10]. For example, attaching camera, infrared and LiDAR payloads, UAVs can provide a low-cost method of obtaining highly accurate 3D photogrammetric data and aerial photography. UAVs are now commonly used in open pit mining operations for applications that include stockpile surveying, 3D pit modelling, facilities management, accident reporting, progress monitoring, and environmental assessment [11]. There are numerous companies offering UAV services for mining applications; e.g., UAV Geomatics, Leica Geosystems, Sky Futures, SenseFly and FlyTerra, to name just a few. Common services include stockpile and open pit volume computations, environmental assessment, aerial mapping and photogrammetry. Although the aforementioned services are thosemost commonly provided by UAV surveying companies, they may also add value to other daily mining operations. For instance, SenseFly offers pre and post-blast monitoring in order to identify the presence of misfires and wall damage. This data can also be used to reconcile the blast results with expected results. GEM Systems offers a UAV equipped with a magnetometer for mineral exploration surveys. Companies such as Barrick have even used UAVs for solids modelling at tailings dams and stability monitoring [11]. UAVs in mining have so far been mostly limited to surface applications. Harsh underground environments pose many obstacles for flying UAVs. The confined space, dampness, reduced visibility, air movement, and lack of control signal propagation hinders most operators from being able to fly a drone underground. It may be that truly practical uses for UAVs underground will require either autonomous or semi-autonomous flight capabilities. Although there are many difficulties with flying underground, the potential benefits from a working system could greatly improve mining operations. The potential benefits of deploying UAV platforms underground include access to unreachable and dangerous locations and removing personnel from unsafe situations. These benefits have the potential to greatly improve mine monitoring and mine safety. Research has shown that current UAV technologies exist that allow for autonomous indoor flight. Extensive research has been done to develop UAV systems that are capable of performing on-board simultaneous localization and mapping (SLAM), which can allow them to navigate and map a foreign environment autonomously [5, 7, 1, 13]. Grzonka [7] successfully used an open hardware quadrotor to autonomously navigate and map an office building. The research outlines the localization, mapping, path planning, height estimation and control of the autonomous quadrotor. Other research has been done that exploits autonomous UAVs for search and rescue. Kassecker [9] proposed a software and hardware framework for a quadrotor capable of indoor and outdoor urban search and rescue and Rudol [19] developed a system for human body detection and geolocalization using an autonomous UAV.The use of autonomous UAVs in search and rescue has the potential to improve situational awareness and surveillance for a rescue team. Similar research has been done that uses autonomous UAVs for indoor exploration. Pravitra [15] outlined a strategy for autonomous exploration of miniature air vehicles (MAVs) within indoor environments and Rudol [19] developed a method for using an unmanned ground vehicle (UGV) and a UAV for cooperative indoor exploration. These studies show that aut"

Jan 1, 2017

By R. Todd Swinderman

"Higher production demands across all bulk handling segments require increased efficiency at the lowest cost of operation, in the safest and most effective manner possible. As conveyor systems become wider, faster and longer, more energy output and more controlled throughput will be needed. Add an increasingly stringent regulatory environment and cost-conscious plant managers must closely review which new equipment and design options align with their long-term goals for the best return on investment (ROI).There are primarily two separate market segments using conveyor belts. One is in process industries such as food, chemicals, paper and powders. Handled in relatively low volumes, the bulk materials that enter these processes are generally of a consistent size and quality. The other market includes mining, coal handling and cement, where the bulk material’s quality and size vary, and the volumes are typically much greater. While both segments face similar issues with safety and environmental control, the properties of the materials handled and the volumes transferred suggest different approaches, with one thing in common: increased belt speeds requiring modern equipment upgrades.Safety at higher belt speedsWith companies recognizing that safety does indeed pay, safety is likely to become a new source of cost reduction. The percentage of mines and processing facilities with a robust safety culture are likely to increase over the next 30 years to the point where it is the norm, not the exception. In most cases, with only a marginal adjustment to the belt speed, operators quickly discover unanticipated problems in existing equipment and workplace safety. These problems are commonly indicated by the larger volume of spillage, increased dust emissions, belt misalignment and more frequent equipment wear or failures."

Jan 7, 2017

By J. Drelich

An improved experimental procedure to measure contact angle has been consolidated with coal surface preparation involving polishing with abrasive paper, alumina powder, and a cloth, followed by ultrasonic and mechanical cleaning. Specifically, the captive-bubble measuring technique has been compared with the sessile-drop technique and the former has been recommended for the examination of the hydrophobic properties of coal surfaces. Results of the research program, which is currently under way, on the examination of the effect of the nature, amount, size and distribution of mineral inclusions in coal on its wettability are briefly reviewed.

Jan 1, 1999

By J. S. Jaspal

Mining of thin coal seams is both difficult and uneconomical. As a result, most of thin-seam coal reserves in the U. S. are not being mined. It is estimated that nearly 910 Gt (K. Unrug, 1985) of coal reserves exist in 355 to 710 mm thick seams. The Bureau is attempting to develop new techniques for mining 150 to 1065 mm thick coal seams. This paper summarizes the research work on existing thin-seam mining techniques, testing on small and full scale physical models of the Bureau slot mining concept, and computer modeling of the full-scale process.

Jan 1, 1992

By Kanaan Hanna

A joint research program between the U.S. Department of the Interior&apos;s Bureau of Mines and Cyprus-Yampa Valley Coal Company is being conducted at the Foidel Creek Mine, Oak Creek, Colorado. This program goal is to study the effects of state-of-the-art, high-speed, automated longwall mining on health and safety, and primarily, ground stability under various geological conditions. The Bureau installed an automated data monitoring system, known as the Ground Control Management System (GCMS), to monitor in real-time the effect of rapid mining on pillar and face loading, stress redistribution in and around the longwall panel, and caving characteristics of the roof. The Bureau&apos;s GCMS, combined with the company&apos;s existing monitoring systems, which include environmental monitoring, a computer programmable conveyor belt system, and gamma ray roof control thickness indicators, has been effectively used to improve safety at the face, increase productivity, and reduce production costs.

Jan 1, 1991

By Zhiguo Chang, QINGXIANG CAI, Ebelia Manda, IZHAR MITHAL JISKANI, XIANG LU, Wei Zhou, Saleem Raza Chalgri

The concept of mine safety is highlighted in the literature of sustainable mining but not extensively discussed. This study analyzes various aspects of underground and surface mine safety and emphasizes its importance in the context of sustainable mining. More specifically, this research attempts to find the relationship between mine hazards and demographic characteristics, examine and compare the perceptual difference among miners, and determine the impact of mine hazards on workplace safety and safety climate. Descriptive analysis, chi-square test, independent samples t test, and linear regression modeling were conducted to achieve study objectives. Results confirmed that mine hazards were significantly associated with age and experience. Miners perceived lower levels of management safety practices, followed by supervisor safety, coworker safety, and job safety. The analysis showed that underground miners reported lower safety scores than surface miners. There was a statistically significant difference between miners’ perception of safety climate (p < 0.05). The results showed that the higher prevalence of mine hazards predicts poor workplace safety and a low safety climate. The regression models revealed that mine hazards have a significant effect on workplace safety (p < 0.05) and safety climate (p < 0.05). In conclusion, the distinctive model of mine safety presented here contributes to the monitoring and design of comprehensive safety interventions and helps to better understand how certain factors interact on multiple levels to influence the overall safety of the industry. In this study, some suggestions are put forward to provide directions to develop a sustainable mine safety system.

Mar 27, 2020