Search Documents

By R. R. Tatiya

This paper describes the local estimation of mineral inventory by kriging. A mineral deposit located between two working levels of a copper mine was examined. Data for this estimation was obtained by underground diamond drilling. The mineral inventory that was computed by this method was compared to the results obtained by global estimation techniques, which were based on information front surface boreholes. A comparison between the ore reserves estimated through kriging and the ore reserves estimated at the mine using conventional methods was also made. This analysis shows that geostatistical methods can be applied to evaluate base-metal deposits similar to the deposit examined in this study. In the part of the mine that was examined, the kriging estimates show an overall increase in metal content at all cutoff grades, compared to the estimates obtained through conventional methods. Also, the ore body profiles are more continuous and regular through kriging, but they are not radically different from the profiles that were previously obtained at the mine. However, the global estimate of the deposit using kriging could not provide reliable results.

Jan 1, 1997

By Jianliang Li, Xi Peng, Guorong Lu

This paper describes a wind tunnel modelling study on airflow and pollutant concentration in a large open pit mine located in southern China. A 1:1000 scale model of the surface mine was fabricated and placed in a wind tunnel. Airflow velocity in the test section of the wind tunnel can be continuously adjusted from 0.3 m/s to 6.0 m/s. In this study, both the present pit condition and the projected final pit condition were modelled. Airflow direction and velocity profiles were obtained. The impact of wind direction and velocity on airflow was also studied. The pollutant concentration distribution in the open pit was simulated using smoke, and a distribution profile was obtained. Respirable dust concentrations at the mine site were measured, then its concentrations at the projected final pit condition were estimated using the obtained pollutant concentration distribution profile. Under normal meteorological conditions, it is expected that the respirable dust concentration for the final pit should not exceed the government standard. Key Words: wind tunnel modelling, open pit, surface mining, scale model, mine ventilation, airflow profile, point source.

Jan 1, 1993

By G. F. Revey

Most commercial explosives contain from 70% to 94% (by weight) ammonium nitrate. When some of the explosives end up in shot rock and ore, through either spillage or incomplete detonation, ammonia and nitrates can leach into the ground water. In recent years, state and federal regulators have applied more stringent water-quality standards, particularly at new mines and development projects. When mining conditions permit, bulk ANFO, a mixture of ammonium nitrate and fuel oil, is the explosive of choice. ANFO is less costly than other explosives but it dissolves readily in water. Several case histories in the United States and Canada show a clear connection between uncontrolled losses of bulk explosives and high nitrate levels in mine effluents. Mining companies have tried several approaches to reduce ammonia and nitrate levels in groundwater. These approaches range from controlling explosive losses to treating the mine effluents. In this paper, controlling explosive losses is addressed For both packaged and bulk explosives, guidelines to limit losses during storage, handling and use are described in detail.

Jan 1, 1997

By J. N. Carras, N. W. Bainbridge

In order to further the understanding of spontaneous heating of longwall goafs a numerical model was developed, based on conservation principles applied to the transport of heat, water vapour and oxygen across the god Advective air flow into the goaf is caused by the differential air pressures across the god The air velocity field within the goaf area was computed using Darcy's law. The boundary and initial conditions concern air pressure, temperature and relative humidity. The oxidation rates and heat generation rates of the goaf materials required for the simulation were obtained from laboratory measurements. The main outputs of the model are temperature, oxygen and water contour maps, the rate of air leakage into the go4 velocity field and pressure distribution across the god. The model while still in its development stage, is able to simulate a heterogenous goafs constructed from different materials with different thermal and mass flow properties. Validation of the model by comparing its output with measurements from within goafs is required before the model can be used with confidence in a predictive sense.

Jan 1, 1995

By Neal Rackstraw, Mamo Meaza

Washington Metropolitan Transit Authority Section E8a consists principally of twin tunnels 1,713 meters (5,620 ft) long, excavated to a diameter of 6.35 meters (20.83 ft) using an open face shield, with a primary lining of four unbolted precast concrete segments expanded at the crown, and a full circle unreinforced concrete final lining with a finished tunnel diameter of 5.08 meters (16.67 ft). The tunnels, constructed in Cretaceous age sediments, are mostly in stiff to hard clay except for a few areas along the alignment that contain dense to very dense fine sand in the upper portion of the tunnel that created a mixed face condition. At two locations unexpected heavy water inflows produced very serious problems in both tunnels. Water flows in the interface area were generally more than 378.5 1pm (100 gpm) and reached as high as 2,649.5 1pm (700 gpm) in the mixed face ground. The nature of the tunnel inflows, the consequences, and the corrective measures adopted will be the subject of this paper.

Jan 1, 1991

By M. A. Trevits, R. J. Matetic

Mining operations have long been accused of causing a disruption to local, domestic and agricultural water supplies. More recently, concern for water supplies has increased with the advent of high-extraction mining techniques, namely longwall mining. Theoretically, any water-bearing zone in the overburden above a high-extraction mining operation may be affected by mining. In some cases, a confining bed may be fractured causing a loss of water to a particular zone. In other cases, increased fracture permeability may enhance the ability of an aquifer to transmit and deliver water. Unfortunately, only a limited number of studies have been conducted that characterize hydrologic changes and also quantify the magnitude of mining-induced subsidence. The US Bureau of Mines (USBM) conducted such a study at a mine site in Greene County, PA. A total of eight water wells were drilled, and hydrologic parameters, such as specific capacity, transmissivity and well yield, were determined both before and after mining. Electronic water-level recorders were installed on each water well to provide continuous observations of water level fluctuations.

Jan 1, 1993

By Merrill P. Allen

The Vernal phosphate rock concentrator is located in the Uinta Mountains near Vernal, Utah. Ore is sedimentary rock from the Phosphoria Formation. Truck and shovel mining is done at a rate of 11,500 TPD. Run of mine ore is crushed and then milled through a SAG mill and ball mill to minus 16 mesh. Milled ore is deslimed using cyclones and hydrosizers. Sands are conditioned with fatty acid, petroleum sulfonate, diesel fuel and frother prior to primary rougher and cleaner flotation. Primary flotation tailing is milled to 95% minus 48 mesh, deslimed in cyclones, conditioned using reagents previously described, and then processed through rougher and cleaner scavenger flotation. Product of scavenger cleaner concentrate is upgraded by reverse flotation of dolomite. Flotation concentrates are combined and dewatered, pulp being milled to 99.5% minus 65 mesh and then thickened to 65% solids. Product is pumped from storage through a 10 inch, 94 mile pipeline to a conversion plant at Rock Springs, Wyoming. Mill tailing is stored behind an earthen dam, water from the settled tailing being reclaimed for mill use.

Jan 1, 1993

By D. C. Wilder

Deformations during heating and cooling of three drifts in granitic rock were influenced by the presence of faults and shear zones. Thermal deformations were significantly larger in sheared and faulted zones than where the rock was jointed. but neither sheared nor faulted. Furthermore. thermal deformations in faulted or sheared rock were not significantly recovered during subsequent cooling thus a permament deformation remained. This inelastic response is in contrast with elastic behavior identified in unfaulted and unsheared rock segments. A companion paper (Butkovich and Patrick, 1986a) indicates that deformations in un- sheared or unfaulted rock were effectively modeled as an elastic response. We conclude that permanent deformations occurred in fractures with crushed minerals and fracture filling or gouge materials. Potential mechanisms for this permanent deformation are asperity re-adjustments during thermal deformations. micro-shearing, asperity crushing and crushing of the secondary fracture filling minerals. Additionally, modulus differences in sheared or faulted rock as compared to more intact rock would result in greater deformations in response to the same thermal loads.

Jan 1, 1986

By Jeffery H. Stricklin

Jim Walter Resources operates five underground coal mines with longwall faces in operation in four of the mines. Due to high air velocities (1000-1200 fpm) needed for methane control together with the friability of the coal, dust control on JWR longwalls offers unique challenges. We have tested many innovative measures to reduce respirable dust concentrations on longwalls with varying degrees of success. These measures include the "shearer clearer" system, different drum water spray configurations, sprays on the longwall belt, stageloader and crusher sprays, wetting agents in the spray water system, and homotropal ventilation. Water infusion of deactivated horizontal methane drainage holes in longwall panels is now being evaluated. A study was completed in November 1986 where water was infused into two horizontal de-gas holes. Personal gravimetric samplers were used to measure respirable dust concentrations and showed a significant reduction in the infused zone. A more in depth study will be conducted. This paper will describe the dust control measures presently used on JWR longwalls, give the results of past studies, and discuss new methods proposed to control longwall dust.

Jan 1, 1987

By Masaji Kato, Yuusaku Tominaga

To maintain good condition of ventilation for both safety and economy, many regulators are installed in a network. In case the open state of a regulator is different from the set point, identification of a broken regulator and a countermeasure to recover airflow distribution in a network must be initiated as soon as possible. An experienced mining engineer can sense a deviation from ordinary airflow quantity. In this paper, a new system to monitor all the regulators in a network is introduced. The basic concept of the system is utilization of both human sensing of airflow rate and computer simulation to understand the macroscopic characteristics of a ventilation network. A fuzzy pattern distinction method is used to process human determination of airflow rate that may be ambiguous. The applicability of the system is demonstrated using the ventilation network of the Horonai coal mine, Japan. In particular, it is shown that the system can identify the regulator to be repaired from information supplied by workers relating to air- flow in a few sensor branches.

Jan 1, 1997

By B. Bergmark, O. Guyot, A. Broussaud, C. Bouché

The Boliden Aitik concentrator in Sweden processes 2,000 t/h (2,200 stph) of low-grade copper ore. The plant consists of five grinding lines that feed four bulk-flotation banks with a scavenger-concentrate regrind mill und a column cleaner circuit with a regrind mill. The authors installed a model-based expert optimizing control system to maximize copper recovery in the bulk-flotation circuit while maintaining an appropriate copper grude in the cleaner feed. The optimizing control system uses on-line assays and calculates and implements set points for cell pulp levels, air rates and reagent- addition rates. It combines the power of a dynamic population-balance model that estimates mineral liberation in each stream, an optimizer that computes appropriate set points and a rule-based module that implements the strategy. The benefits have been evaluated over a period of three months. The model-based expert optimizing control system generates a measurable increase in copper recovery, around 0.5%, and an optimized bulk-concentrate grade. The need to maintain the optimizing control system and other practical aspects are discussed.

Jan 1, 2000

By Howard M. Wells

The future is uncertain. In these circum- stances how can we rationally decide whether to commit funds to an investment that may or may not turn out to be successful? To date no certain answer to this problem has been found, nor is one likely to be found in the future. At best we can attempt to assess the possible outcome in terms of probability, taking into account all sources of information that may be available at the time the decision must be made. This subject is addressed with some trepidation and much humility. Any attempt to fore- tell the future is by its very nature controversial. The purpose of ' this .chapter is to present a proposed rationale for decision making under uncertainty which relates the probabilistic risk of the investment to the capacity of the firm to absorb possible unfavorable consequences if they should occur. It is not the intention to propose a cut-and-dried methodology but rather to examine the conceptual philosophy on which a methodology may be based.

Jan 1, 1979

By Ruoming Gong, Arindam Samanta, Ragula Bhaskar

Three studies conducted at the University of Utah relating to the effect of scrubbers on face airflow patterns, the resulting dust exposure of operators and the development of a throat scrubber for continuous miners are summarized in this paper. The first study involved full-scale laboratory tests to determine the potential dispersion patterns and transport of dust at a continuous miner face, using different ventilation configurations and a scrubber. Concentration maps were developed and potential exposures at operator positions were examined. The second study involved the development of a 3-D numerical model to predict airflow patterns generated by a scrubber at a continuous miner face. The model was designed to evaluate the role of various face parameters on airflow patterns at a miner face and to complement the full-scale testing. The third study involved the design and fabrication of a low profile hydraulically powered continuous miner throat scrubber. The scrubber uses three hydraulic motors and small diameter fans to draw about 3000 cfm (1.42 m3/s) of air and uses a flooded bed scrubber to filter dust particles.

Jan 1, 1993

By Satya Harpalani, Xue Zhao

This paper discusses the results of an experimental investigation to study the release of methane in coalbeds. Absolute porosity of coal samples was first determined experimentally. Following the porosity measurement, adsorption/ desorption tests were carried out to determine the gas content of coal and the rate at which it is released. Finally, micrographs were obtained using electron microscopy and the use of a physical model, developed to explain the gas flow behavior of coal, was justified. The results of this study indicated that the measured absolute porosity of the coal sample was between 5 an 6%. This was significantly lower than the porosity estimated by comparing the micrograph area occupied by the pores and the area of observation for several micrographs, suggesting that coal has a large number of pores with a very small volume. The micrographs also clearly indicated that coal has a large interconnected network of cleats and microfractures. The adsorption/desorption experiments showed a hysteresis between the adsorption and desorption isotherms. Also, the rate of desorption was found to be strongly dependent on the particle size of the specimen.

Jan 1, 1989

By E. Kokinou

The main scope of the present study is to investigate the suitability and sensitivity of the magnetic susceptibility as a pollution monitoring tool in urban areas. For this purpose, a municipal park located in the centre of Chania city, which may be affected by traffic and domestic heating pollution, was selected as the study area. In the context of the present work, magnetic susceptibility measurements were conducted in two phases. Surface soil samples were collected in 2006 from the area under investigation and they were analyzed in order to estimate the spatial distribution of the magnetic susceptibility. One year later, mapping of the magnetic susceptibility has been contacted in situ using Bartington MS2D and MS2F sensors. Additionally, soil samples were collected from selected positions in order to compare the values of the magnetic susceptibility with that estimated in 2006 research. Both investigations indicate high values of the magnetic susceptibility around the park near the roads and in a small area inside the park where a café is located.

Jan 1, 2008

By M. J. McPherson, P. Mousset-Jones, G. Danko

Ventilation and refrigeration fortune climate modification contributes significantly to the operating costs of a deep hot mine. Mine climate simulation programs can he used to minimize the impact of these costs. There are several computer codes available to assist in this work. Whichever simulation program is used, it is the mine ventilation engineer who must supply the input data. This paper raises and answers the following question, namely, what accuracy is required of the basic input parameters, in order for a certain precision to he obtained in the predicted air temperatures? In the first part of the paper a new approach is described to estimate the dry and wet bulb temperature of the airflow, either in a dry or wet roadway. The calculation procedure allows an arbitrary temperature change with time, using Duhamel's superposition solution. Matrix-vector representation is applied to simplify the computational structure. In the second part of the paper the sensitivities of the dry and wet bulb air temperatures are analyzed, to the changes of the rock thernrophysical properties, the heat transfer coefficient, and the wetness factor.

Jan 1, 1987

By C. B. Rash, W. W. Fowler, Gill Montgomery

INTRODUCTION Fluorspar is the common term used for the mineral fluorite, which is naturally occurring calcium fluoride (CaF2). It is the principal source of fluorine, the most reactive of the chemical elements, from which a great variety of unique and strategically important chemicals are produced. Commercial deposits of fluorspar are widespread throughout the world, and its availability is essential to the industrial progress of all nations. GEOLOGY AND MINERALOGY In its pure form fluorspar, CaF2, contains 51.1% calcium and 48.9% fluorine, and has a sp gr of 3.18 and a hardness of 4. It is commonly a glassy mineral. colorless, white, or grayish. but may also be various shades of purple, pink, blue, green, yellow, or tan. It belongs to the cubic system mineralogically, and commonly crystallizes into cubic shapes in vugs and cavities, although most of it is massive, with interlocking crystals. Minable fluorspar deposits, in descending order of importance, occur as bedded limestone replacement deposits along fault zones; fissure-filling vein deposits; breccia filling in limestones, dolomites,

Jan 1, 1985

By A. Platts, K. Leung, P. Rohner, P. Munro, B. Coulter

The Hilton Concentrator treats a laminated stratiform silver- lead-zinc ore to produce separate lead, zinc and bulk concentrates. Commissioning commenced in December 1989. Grinding circuit performance is above design with a mean flotation feed sizing of 80% passing 65 microns at 800 000 tonnes / year throughput. Grinding is done in two stages with an open circuit low diameter : length ratio SAG mill followed by a closed circuit ball mill. SAG mill control philosophy is to maintain a fixed feedrate for stability of flotation and to control mill charge weight to a setpoint with feed water. It is planned to increase throughput to 1 million tones / year in the second half of 1991. Proposed milling circuit modifications include close circuiting the SAG mill by recycling a portion of the ball mill cyclone underflow, increasing the SAG mill speed from 73% to 79% of critical and offloading of lower than feed grade -20mm /+7mm SAG mill ore scats. This paper will describe current mill operating practice with operating data and key mill developments since the beginning of operations.

Jan 1, 1992

By Julián Ortiz C., Clayton V. Deutsch

Indicator simulation allows specification of different continuity of high and low values through the use of grade thresholds. The sequential implementation of indicator simulation has been widely used, but the problem of order relation deviations remains a significant drawback. A new procedure for "Hierarchical Indicator Simulation" is introduced that avoids order relations and offers greater flexibility than the conventional sequential approach. The new implementation simulates all locations at the largest threshold and then considers decreasing thresholds in turn. All nodes with grades that are above the previous threshold are excluded from the domain of the current threshold and therefore, they are not used as conditioning data. The probability of being above or below the threshold is calculated using simple indicator kriging using all conditioning data in the domain, thus the covariance structure is preserved. The theoretical framework of this new approach is fully developed. Practical implementation details are discussed. Application to a copper deposit shows the advantages and drawbacks of the method. Finally, the possibility of incorporating multiple-point statistics is discussed.

Jan 1, 2002

By Greg Barfoot, Kurt Keskimaki

The Henderson Mine is located approximately 50 miles west of Denver, Colorado. A project is underway to replace the existing rail system which transports molybdenum ore 15 miles from the mine to the mill using three flight conveyor system. The first conveyor is a 1 mile, high lift conveyor which transports the ore from an underground crushing station to the end of the existing rail tunnel. The second conveyor is 10 miles in length and utilizes the existing rail tunnel to transport the ore from the mine, which is on the east side of the Continental Divide, to the mill located on the west side. The third conveyor takes ore from the tunnel portal to the mill through a series of 7 horizontal curves and inclines up to 15 degrees. The project applies advanced conveyor design to tackle the installation of the system in an operating mine and achieve the highest possible level of reliability. This paper outlines the design process for this system, discusses the options which were evaluated and how the current design evolved.

Jan 1, 1998