Search Documents

By W. R. Reed, S. Klima, J. Driscoll, T. W. Beck

"Tests were conducted to determine properties of four foam agents for their potential use in longwall mining dust control. Foam has been tried in underground mining in the past for dust control and is currently being reconsidered for use in underground coal longwall operations in order to help those operations comply with the Mine Safety and Health Administration’s lower coal mine respirable dust standard of 1.5 mg/m3. Foams were generated using two different methods. One method used compressed air and water pressure to generate foam, while the other method used low-pressure air generated by a blower and water pressure using a foam generator developed by the U.S. National Institute for Occupational Safety and Health. Foam property tests, consisting of a foam expansion ratio test and a water drainage test, were conducted to classify foams. Compressed-air-generated foams tended to have low expansion ratios, from 10 to 19, with high water drainage. Blower-air-generated foams had higher foam expansion ratios, from 30 to 60, with lower water drainage. Foams produced within these ranges of expansion ratios are stable and potentially suitable for dust control. The test results eliminated two foam agents for future testing because they had poor expansion ratios. The remaining two foam agents seem to have properties adequate for dust control. These material property tests can be used to classify foams for their potential use in longwall mining dust control. IntroductionAbout one-half of U.S. underground coal is produced by longwall mining, which allows for mining high volumes of coal but generates significant amounts of coal mine dust. This can lead to overexposures for longwall miners and possibly occupational respiratory diseases, including black lung and silicosis, which have no cure and can be disabling or fatal. The only method to avoid these occupational illnesses is through elimination of exposure to respirable coal mine dust and crystalline silica (quartz). The current occupational exposure limit for respirable coal mine dust is 1.5 mg/m3 during each shift that a miner is exposed in the active workings of the mine or in mine facilities (Mine Safety and Health Administration (MSHA), 2015a). When respirable quartz is present, the mine must maintain average concentrations at or below 0.1 mg/m3. If the mine exceeds the 0.1 mg/m3 respirable quartz dust concentration, then the applicable respirable dust standard is reduced, calculated as 10 divided by the percent quartz present (MSHA, 2015b)."

Jan 1, 2018

By C. Newman

"As underground mining continues to operate at deeper depths and in more complex multiple seam mining geometries there has been an increased demand for higher design standards in ground control safety and stability within the mining industry. For the past 20 years, NIOSH has developed and validated a number of software tools to aid in the development of safer mining environments with respect to improved roof support performance, pillar stability in longwall and room and pillar mines, formation characterization, the prediction of roof conditions, etc. These tools are available, free of charge, to the mining industry as stand-alone software packages. As cloud computing gains momentum, there is a definite need to develop internet based applications for mine design that would be easily accessible to any user at any time, including underground where permitted. This paper introduces a new web-based product which will allow for faster and easier access to existing ground control designs, on-the-fly calculations in the field as needed, and instant online collaboration between operations personnel and planning engineers. It is expected that the industry will rapidly embrace this product and, as it is common with all new innovative technologies, it will be a new paradigm for mining engineering computer applications. INTRODUCTION Since its release to the public in the late 1980's, the World Wide Web has drastically changed from a collection of static HTML web pages to a dynamic vehicle driving e-commerce, collaborative working relationships, and the mass distribution of information and media (Offutt, 2002). Recent developments in Internet capabilities, such as Cloud Computing and Software as a Service, have begun a migration away from desktop-based software in adoption of the web application (Hayes, 2008). Web applications, or web apps, are designed on the client-server architecture paradigm in which the client, or user, can interact with an application through web browsers without disrupting or installing software on potentially thousands of client computers (Nations, 2015). Currently, web-based software applications are being utilized in all business sectors and markets from commerce, finance, media, and even engineering. In fact, the Alabama Department of Transportation has developed a web-based geotechnical geographical information system (GeoGIS) for the management of and access to geotechnical and subsurface data for transportation projects across the state (Graettinger, et al., 2001). Similarly, Dyno Noble has developed a service application for explosive engineers. The Explosives Engineers' Guide application equips users with a full range of product information as well as on-demand blasting calculations for powder factor, airblast prediction, ground vibration, etc. Through the incorporation of a web server, one is able to utilize the functionality of the desktop-based software through a web browser located on any personal computer, tablet, or Smartphone (Vaughan-Nichols, 2002)."

Jan 1, 2016

By Shakuntala Tudu, Indrajit Paul, Surajit Sinha, Pulibandla Basaveswara Rao, Shaik Mahaboob Basha, Srinivas Dwarapudi

The iron and steel manufacturing sector directly accounts for 7–9% of global CO2 emissions. Raw material preparation, such as iron ore sintering, pelletizing, and cock making, is the major CO2 emitter. As climate change becomes a bigger concern, steel manufacturers need to lower CO2 emissions without hindering efficiency or increasing costs. In recent years, the percentage of iron ore pellets in blast furnaces has increased due to its uniform size, good reducibility, and high tumbler index. Pelletizing is energy-intensive and emits considerable CO2. Around 20% of CO2 emissions during pellet making come from fluxes. In the present work, the authors established a novel CO2- free flux called wollastonite (CaO.SiO2) for sustainable palletization. Pellets with varying percentages of wollastonite (0–6%) are prepared and tested for chemical, physical, and metallurgical properties. Image analysis through an optical microscope is carried out to quantify the phases of fired pellets. SEM–EDS is performed to evaluate the chemical composition of the melt and slag phases. The results showed that the reducibility index (RI) and swelling index (SI) of pellets decreased with an increase in wollastonite dosage. Pellet strength increases with an increase in wollastonite addition up to 1.2% CaO (2.27% wollastonite), and a decrease in strength is observed thereafter. The increase in strength is attributed to the increase in slag bonds. The decrease in strength beyond 1.2% CaO is mainly because of an increase in low melting eutectics and more magnetite content. Pellets with 2.27% wollastonite to get 1.2% CaO showed good physical and metallurgical properties.

Mar 4, 2024

By Allan Breitenbach

Leaching has been used since the 1600s on unlined ore dumps and since the late 1970s on lined leach pads for the recovery of metals from mined ore, the latter typically called ?heap? leaching and the former ?dump? leaching. Modern day run-of-mine (ROM) or crushed ore heaps are stacked in controlled lifts on lined leach pads and irrigated with a solvent solution (dilute alkaline cyanide for precious meals, dilute sulfuric acid for base metals and uranium). Conventional lined leach pads store process solutions and any storm water, snow melt and cumulative wet season surplus water by gravity flow to external ponds. Impounding valley leach pads (also known as valley fill heaps) differ from conventional leach pads by storing various combinations of process liquid solution and surplus water within internal ponds by using the interstitial pore volume of the ore. While impounding liquids within the heap is simple in concept, impounding leach pads are more complicated for construction and containment compared to conventional leach pads with external ponds.

Jan 1, 2012

By Yi Luo, Jian Yang, YUJIA LIAN

Scale physical models, constructed according to the principle of similarity theory, have been widely used to simulate the mining disturbances to surrounding strata and to evaluate the effectiveness of implemented ground control techniques. This technique has also been used for studying mining-induced surface and subsurface subsidence. The movements of the observation points installed on the physical model at different mining stages are currently measured using total station which is time-consuming and inaccurate especially on small scale models. A photogrammetry-based measurement system has been developed. During a physical modeling process, photos of the model can be taken during the simulation process reducing survey time from hours to a few seconds. A program, Photogrammetry Analysis for Physical Modeling of Mine Subsidence Process (PAPMMSP), developed based on photogrammetric principle is used to quickly identify the installed observation points and accurately determine their coordinates. The measurement accuracy is well under submillimeter level—an ultra-important advantage as any measurement errors in coordinates are magnified by the model dimension scale (commonly 20 to 400). A physical modeling case of subsurface strata movements and deformations associated with longwall mining operations is presented in the paper to demonstrate the functions and capabilities of the developed photogrammetry program.

Aug 11, 2020

By Louis A. Panek

Research on roof bolting has developed significant information with respect to the functions that can be performed by properly installed bolts and the methods that can be used to ensure that effective installation has been achieved. The present paper brings together results that are pertinent to the design of a bolting system for reinforcing horizontally stratified mine roof with vertical bolts. The design approach is based on the use of bolts to decrease the maximum bending stress within an arbitrary sequence of roof strata (such as shown by figure 1) in which the only loads are the weights of the individual beds. The use of rock bolts to achieve other objectives, such as to stabilize a fractured rock mass on the periphery of a mine opening (3), is excluded from consideration herein.

Jan 1, 1964

By Xinchun Li, Youdi Zhang

AI is one of the computing methods, artificial intelligence performs its calculation by simulating the intelligent behavior of human beings. It is regarded as one of the most important scientific achievements in the 20th century, A1 has been developed rapidly in recent years with the development of the computer technique .The application of AI in the mineral industry has also obtained rapid progress sine AI has been used in early 1980's, such as evaluation of resource, underground mining, surface mining and mine safety etc. It has played an important role for increasing mining efficiency, improving mining management and ensuring the safety of the miner. An integrated A1 system has been developed for coalmines environment management in this paper.

Jan 1, 2002

By W. P. Diamond, A. C. Smith, J. A. Organiscak, T. P. Mucho

The U.S. Bureau of Mines examined bleederless ventilation practices to evaluate their use as a spontaneous combustion control measure in U. S. coal mines. Results indicate that restricting airflow into mined-out areas (bleederless ventilation) is recognized worldwide as a spontaneous combustion control measure. However, ventilation practices commonly used to limit airflow to mined-out areas are not easily applicable to United States mining conditions, systems, experience and regulations. The types of bleederless ventilation systems used throughout the world and the spontaneous combustion risks associated with these systems are discussed. Primary design considerations for bleederless ventilation consist of the interaction of ventilation practices, methane drainage, ground control, seal construction and mine monitoring. Technological improvements needed for U.S. application of bleededess ventilation are also discussed.

Jan 1, 1995

By J. D. Forrester

I have availed myself of the opportunity to prepare, and to give this talk because, as incumbent Chairman, I am directed by the Bylaws of the Council of Education to make an Annual Report of the Council activities which have transpired during the past year. In addition, and inasmuch as I have this captive audience, I am taking the liberty to express also some beliefs I hold about various other elements of Mineral Industry education. First, my report is that constructive progress has been achieved in the Council of Education during 1960-61. These advancements have been particularly notable through projects carried on by the Committee on Meetings and Programs, by the Student Chapters Committee, by the Accrediting Affairs Committee and by the Committee for Securing Better Representation of Mineral Industry Colleges. I believe each of these groups will report concerning details of their respective programs at the Business Meeting of the Council. On the other hand, not as much has been done in some areas of work as I had hoped would be the case when I took office as Chairman last February. Let me make clear that these delinquencies, for the most part, have resulted through my ineptness in handling of affairs; they are not caused by the failure to perform various assignments which I have given to council members.

Jan 1, 1961

By Heinz Petry

In deep strip mines the job of moving overburden may be so much bigger, and more costly than the removal of coal or ore that the operation is often called dirt mining. Constant improvement in stripping machines and techniques of using them is needed to offset rising costs and to increase production in mines that are now operating, and to make it economically possible to work deeper or thinner deposits.

Jan 1, 1962

By A. G. Moon

Kennecott Copper Corporation's Chino Mines Division concentrator is located in Hurley, New Mexico. Construction of the concentrator was started in 1910 and its capacity was progressively increased over the years to the present nominal 20, 425 t/d of ore (22, 500 stpd). The principal copper minerals present in the ore are chalcopyrite and chalcocite with much of the chalcotite intimately associated with pyrite. Lime is used to depress pyrite, and flotation at a high pH or alkalinity is required for optimum recovery of chalcocite with good rejection of the pyrite. Regrinding is also required to liberate chalcocite-pyrite middling grains. Accurate control of the lime addition is necessary to obtain both optimum metallurgy and minimum lime usage. At low pH levels, flotation cell control is difficult due to excess froth, but excessively high pH levels can go unnoticed because froth characteristics do not change from those experienced at the deisred pH. With manual control of the lime addition, the desired pH can be exceeded for periods of up to two hours. In 1972 a major renovation of the flotation and regrinding circuits was com¬pleted and at that time a new lime distribution and control system was placed in operation. Limestone is obtained from a nearby quarry west of Hurley. The limestone is crushed, sized and fed to a rotary kiln and the quicklime product is stored prior to slaking. The lime is slaked, as required, in a mixing tank-classifier type slaker and the lime slurry is pumped to a concentrator storage tank from which it is distributed through a conventional closed loop system. The current average lime usage rate is approximately 6 kg/t of ore (12 lb per st).

Jan 1, 1976

By Y. J. Wang

The Hardy Cross iterative method is the most popular technique for solving a ventilation network problem with natural air splitting. This method traditionally solves each mesh equation by an approximation during each iteration. Thus, it is interesting from both a theoretical and a computational viewpoint to be able to solve for an exact solution to the mesh equation. Presented in this paper is an algorithm for computing the exact solution to the mesh equation with a variable fan pressure. The algorithm uses signum functions for air quantities to generate an alternative mesh equation in the form of a quadratic equation that has two solutions defined by the well-known quadratic formula. The condition that the derivatives of the alternative and the original equations must be the same provides a basis for the correct choice between the solutions.

Jan 1, 1998

By Franklin B. Woodbury

As part of its goal of helping maintain an adequate supply of minerals to meet national economic and strategic needs, the U.S. Department of the Interior's Bureau of Mines is evaluating alternative technologies to treat oxidized taconites. Since process control is an essential element in the application of these process technologies, research was performed with a prototype monitoring system. A Californium-252 neutron source and a thermal neutron capture- gamma ray spectra analysis method was utilized to measure the amount of iron and the percent solids in the process slurries. The concentrate and tailing streams in a 410-kilogram-per-hour (900- pound-per-hour) pilot plant employing a selective flocculation and cationic flotation process were monitored. The results obtained showed that the thermal neutron capture-gamma ray reaction can be used to provide process control parameters.

Jan 1, 1979

By Lihong Zhou, DAVOOD BAHRAMI

A reliable and stable ventilation system is essential to the safe operation of underground mines. The stability of a mine ventilation system becomes extremely critical when responding to a fire incident, as an unstable ventilation system will pose a risk of airflow reversal. The reversed airflow could bring fire contaminants, such as toxic gases and smoke, unexpectedly to working areas. In the past few years, there has been a growing interest in the study of ventilation network stability using the concept of resistance sensitivity, which is described as an indicator of how the airflow in an airway is reacting to a resistance change of other airways. Several methods of calculating the resistance sensitivity in a mine ventilation network have been developed by researchers and scholars around the world. However, those proposed methods rely heavily on a vast number of mine ventilation simulations, which is time-consuming and computer-resource intensive, especially for a large-scale mine ventilation network. In this study, a derivative method calculating the resistance sensitivities with a single mine ventilation simulation is developed and implemented into the MFIRE mine fire simulation software. The results from the derivative method were verified against the results from a traditional method. The derivative method is proved to be reliable and accurate.

Dec 1, 2022

By Karl R. Zipf

A tube bundle system (TBS) is a mechanical system for continuously drawing gas samples through tubes from multiple monitoring points located in an underground coal mine. The gas samples are drawn via vacuum pump to the surface and are typically analyzed for oxygen, methane, carbon dioxide and carbon monoxide. Results of the gas analyses are displayed and recorded for further analysis. Trends in the composition of the mine atmosphere, such as increasing methane or carbon monoxide concentration, can be detected early, permitting rapid intervention that prevents problems, such as a potentially explosive atmosphere behind seals, fie or spontaneous combustion. TBS is a well-developed technology and has been used in coal mines around the world for more than 50 years. most longwall coal mines in australia deploy a TBS, usually with 30 to 40 monitoring points as part of their atmospheric monitoring. The primary uses of a TBS are detecting spontaneous combustion and maintaining sealed areas inert. The TBS might also provide mine atmosphere gas composition data after a catastrophe occurs in an underground mine, if the sampling tubes are not damaged. TBSs are not an alternative to statutory gas and ventilation airflowmonitoring by electronic sensors or people; rather, they are an option to consider in an overall mine atmosphere monitoring strategy. This paper describes the hardware, software and operation of a TBS and presents one example of typical data from a longwall coal mine.

May 1, 2013

By A. Benchekroun

The phosphate mining industry is confronted everywhere in the world with financial difficulties and low prices which prohibit further investments and development of new mines even in regions with a comparative cost advantage (North America/ North Africa/ and Middle East). But old mines are being progressively exhausted/ and if no replacement mines come on stream in the near future/ we may soon find ourselves (around the year 2000) with a global annual production capacity of 160 million tonnes of marketable phosphate rock instead of the capacity of 200 million tonnes existing today. Unless prices improve/ phosphate rock/ a non-renewable resource and a vital commodity to world agriculture/ may turn to be in short supply to world fertilizer industry. Whatever the extent of recovery of fertilizer demand/ the expected decline of the production capacity during the 1990 I s is bound to cause the disappearance by the year 2000 of the important surplus characterizing today the supply/demand balance.

Jan 1, 1995

By T. W. Oshnock

Pulverized coal (PC) and other injectants can be injected into the blowpipes of a blast furnace to decrease coke requirements. Throughout the history of blast-furnace development, there have been many attempts at injecting PC. In the 1960's a more serious effort was made to improve pulverized coal injection (PCI) technology. However, because of the additional capital requirements and the projected near-term inexpensive cost of other injectants, very few PC1 systems were installed. When the second oil crisis occurred around 1979, the shortage and high cost of fuel oil caused blast-furnace operators to operate without oil injection. It was soon discovered that blast- furnace operation without oil was not as smooth or efficient. Experiments with PC1 quickly showed that coal was a good replacement for oil which resulted in the rapid application of PC1 in both Europe and Japan. As a result, PC1 technology for blast-furnace operation has progressed rapidly during the 1980's. This paper will describe the worldwide status of PCI, characteristics of different PC1 systems, the effect of PC1 on blast-furnace process parameters, and the economic effects of using PCI. Results from the USS Blast-Furnace Thermochemical Projection Model comparing the effects of different coal properties and the effects of other tuyere injectants such as oil and natural gas will also be described.

Jan 1, 1988

By A. L. Mular

Steady-state material balances calculated from data measured at various locations around process units are useful for many purposes, such as metallurgical accounting, on-line control, and the development of mathematical models. Often it is possible to calculate material balances by several independent procedures when excess measurement information, i.e., redundant data, is available. Clearly, if the data were collected without measurement errors, a theoretical condition never found in practice, all material balances calculated from redundant data would be in agreement. The real situation is that error exists in practical measurements, so that the results of material balances determined from available optional procedures differ. Consequently, best fit computational procedures to improve the material balances by taking measurement errors into account have been formulated. Such procedures can be used also to judge whether measurements are grossly in error due to either faulty observations or defective data sensing devices. A variety of mathematical techniques are available which serve to adjust raw data. The adjusted data permit mass balancing that does not depend on the computational method. To illustrate the need for an adjustment procedure, Table 1 shows a raw data set acquired around the Brenda Mines Ltd. No. 4 grinding circuit shown schematically in Fig. 1. At least seven optional ways to calculate a circulating load ratio may be employed. These are shown in Table 2 where, depending upon the calculation [ ]

Jan 1, 1979

By C. Flores

The most common experimental approach of studying one variable at a time while holding all others constant is extremely inefficient. Use of statistical methods enables engineers and scientists to obtain meaningful information with the fewest experiments, reducing cost and wasted effort. In particular, the Taguchi method can be more efficient than traditional full factorial experiment designs, as it can study more variables with fewer nuts, and it is more robust against process "noise." Taguchi designs are also simple to formulate and the results can be analyzed by simple PC spreadsheets. The role and benefits of using the Taguchi method in experiments to develop and optimize processes is discussed.

Jan 1, 1998

By David H. Dahlem

Uranium is a very mobile element geochemically and is widely dispersed in the lithosphere and hydrosphere. Under oxidizing conditions, it is particularly widespread and appears in all parts of the surface hydrologic system. As a result, this system is a leading candidate in uranium-resource assessments as a new base from which total resources might be estimated. No other sampling system provides the large volume geochemical capture as the continental hydrosphere and is as pervasive and non-selective regardless of rock type. However, the water system as a uranium metal sampler is not without drawbacks as the development of a National sampling program based on it has shown, In spring 1973, the National Uranium Resource Evaluation (NURE) was announced by the U. S. Atomic Energy Commission (AEC). The program was conceived to provide an evaluation of the domestic uranium resources and to identify areas favorable for uranium exploration. The specific NURE objectives are as follows (Bowyer, 1974): 1. To provide a preliminary evaluation of domestic resources and favorable exploration areas by early 1976, based on existing data. 2. To conduct a comprehensive evaluation of domestic resources and favorable areas by 1980, based on advanced state-of-the-art information. 3. To conduct an R&D program into new and improved procedures, equipment, and technology for uranium exploration and assessment. 4. To disseminate information on new exploration concepts and technology.

Jan 1, 1976