Search Documents

By S. A. Anzalone

The Helvetia copper deposit is a large undeveloped Laramide porphyry copper system located in the Santa Rita Mountains, Pima County, Arizona. This porphyry copper system consists of four areas of copper mineralization: Rosemont, Peach-Elgin, Broadtop Butte, and Copper World. Asarco refers to the four areas collectively as the "Helvetia Deposit". Mineralization and alteration are primarily contact pyrometasomatic, and zoning of hydrothermal alteration and sulfide mineral assemblages are similar to those observed at the Twin Buttes and Mission copper mines located approximately 32 km west of Helvetia. Asarco acquired the Helvetia Deposit in 1988 and has continued the exploration and development effort since then. A considerable amount of excellent geological work has been completed in the area but little information has been published on developments since the mid-1950's. The geology of the deposit as developed by numerous geologists over the past 75 years and the large, bulk tonnage low grade copper deposits outlined in recent years will be briefly reviewed in this paper.

Jan 1, 1992

By N. Langsford

The Archaean Yilgam craton has been a major gold province since 1888 with production and reserves of about 4700 tonnes. Production in 1994 was about 135 tonnes. The largest deposit, the famous Kalgoorlie Golden Mile, contains about 2000 tonnes of gold. About 40 deposits containing more than 35 tonnes (1Moz) of gold has been discovered so far in the Yilgarn. Most of the craton has deep weathering profiles inherited from previous tropical climatic conditions, modified by subsequent arid conditions. A mantle of transported material covers much of the variably stripped weathering profiles. Resolving the geology of the volcanic-sedimentary units (greenstones) and the structures that host the gold mineralization relies heavily on aeromagnetics and shallow drilling.

Jan 1, 1995

By Peter Zhang, Daniel Su

Following the first longwall excavation at a deep-cover gas well site, the pre-mining modeling prediction of longwallinduced casing deformations in the fully cemented production casing were in excellent agreement with post-mining Caliper survey results. However, after second panel mining, the post-mining Caliper survey revealed a large plastic deformation near the top of the Pittsburgh Seam. The focus of this paper is to identify the possible cause of such an anomalous deformation. Very high longwall-induced casing stress near a thick claystone layer at 23 feet above the Pittsburgh seam horizon was identified as the primary cause. Leaving the production casing uncemented or using softer cementing material between intermediate and production casings is identified as the best practice.

Feb 1, 2024

By A. F. Stewart

Slope design in an open pit mine includes the determination of a number of parameters, including bench height, bench face angle and berm width. By way of a case history of two highwall slopes (160m and 220m high) excavated in dipping strata in an operating coal mine, this paper illustrates the influence that bench face angle can have on the stability of an entire slope. The two highwall slopes, the lower of which experienced significant instability, were excavated in essentially the same lithologic and structural environment, with the main differences between the slopes being the angle at which the bench faces were excavated and the excavating methods that were employed. In addition to describing the instability that occurred on one of the pit walls, relevant aspects of the engineering geology, slope design and excavation procedures are described.

Jan 1, 1998

By E. B. Kroeger

Spoil instability has been a problem at a coal mine in interior Alaska. Parameters such as original site topography, groundwater conditions, material properties, spoil-pile geometry, geology, permafrost, natural slope instability, changing weather conditions, and dense, near-surface vegetation have interacted to produce unstable slopes. Several failure modes have been identified including deep seated earth block slides, bimodal earth flows, and solifluction. Thawing of permafrost also created conditions where sliding of spoil along the interface separating the spoil and the natural ground surface occurred when the cohesion and the friction angle of that zone was reduced to zero and below 15?respectively.

Jan 1, 1992

By Y. Akin

The floatability of a typical boron mineral, colemanite (Ca2B6O11.5H2O), is shown to be hindered by the presence of montmorillonite type clay minerals. The clay is found to act in the form of slime coating. The mechanism of slime coating is investigated using pure colemanite and clay and their mixtures with an anionic reagent in a microflotation cell. Adsorption, flotation, solubility, zeta potential and scanning electron microscope studies reveal that slime coating occurs through electrostatic attraction. It is possible to minimize the effect of slime coating either at high surfactant concentration or at high pH values.

Jan 1, 1997

By W. D. Keller

Scan electron micrographs, SEM's, will be shown of representative refractory clays from Missouri deposits, with counterparts from other localities. The story is in the pictures, ("1000 words in each picture"), but clay types include the following. Plastic, semi-plastic, and semi-flint "fire clays" of Missouri have textures which appear to retain certain relic texture of ball clay. Flint clay is composed of tightly interlocking packets, sheaves, and books of kaolinite. Diaspore and boehmite mineral textures characterize those "clays". Surface-boulder diaspore shows very pronounced recrystallization and crystal enlargement from original, unexposed first-grade diaspore.

Jan 1, 1977

By Larry F. Drolet

Charleston, SC is anything but boring. The city was founded in 1670 and has played a significant role throughout the history of the United States. Located along the coast of the Atlantic Ocean in the southeastern United States, Charleston was a vital city in America?s early existence. Charleston?s coastal location has helped the city become the fourth largest cargo port in the United States and earn the 2011 designation as the number one travel destination in the United States by the Conde Nast Traveler Magazine. Part of Charleston?s charm and beauty can be attributed to its historic structures and churches that line nearly every sidewalk, roadways that were laid out based on the width of horse carriages, great weather, southern hospitality and coastal living. Now imagine the challenges of installing new, or re-placing aging infrastructure, in this setting. Every shovel full of dirt, every stick of pipe and every roadway sub-surface has its own historic story to tell. For engineering minded individuals, Charleston?s infrastructure has almost as fascinating a history as its more visible surface structures. Charleston was among one of the first American cities to construct separate sanitary and storm water drainage infrastructure. This concept has roots dating back to the city?s founding and is a credit to the foresight of its founding fathers who understood the basic health differences between sanitary and storm water.

Jan 1, 2013

By Marshall D. Himes

The Pima mine, 39,000 ton per day copper mine, is located 17 miles south of Tucson, Arizona. The mine is in a sequence of Paelozoic and Mesozoic sediments striking east-northeast and dipping southeasterly intruded by a Tertiary quartz monzonite porphyry. The Paleozoic Permian(?) dolo¬mites, limestones, and sandstones have been altered to talc-silicate skarn, marble and quartzite. The overlying Mesozoic Triassic(?) clastic sediments have undergone some recrystallization and hydro¬thermal alteration. The clastic metasediments are divided into three distinct lithologic units, lithic arenite, arkose, and inter¬bedded and overlying black argillite. Three types of hydrothermal alteration in the clastic rocks are propylitic alteration (epidote, chlorite and quartz, with or without sericite), quartz-sericite alteration, and potassic alteration (K-feldspar and quartz, with or without sericite and chlorite). The porphyry has undergone potassic alteration. Dominant structures are an east-west post mineral fault in the western part of the pit, and strong low angle faulting and shearing which truncates the ore body at depth. Two joint sets, one parallel to bedding and the other at right angles to bedding are prominent in the mine. Faulting is in two dominant directions, one striking northwest, dipping northeast and the other striking northeast, dipping northwest. Mineralization is predominantly disseminated pyrite and chalcopyrite, and molybdenite-quartz veinlets. There are lens important amounts of magnetite, hematite, sphalerite, galena, tennantite and bornite. Mineralization is believed to be both structurally and chemically controlled.

Jan 1, 1972

By Douglas N. Kendall

There are three definite steps in the making of a mining industry in any country. These are as follows: Step A - Geological Mapping This step covers the basic geological mapping of the country at scales of 1/250, 000 up to l/50, 000. This step eliminates territory and directs the exploration teams to the areas of potential interest. Step B Prospecting This step includes all phases from detailed geology through geophysics and drilling up to the point of proving that an economic ore body exists. Step C - Mine Development This is the expensive step, involving the creation of the mine, including shaft-sinking, ore treatment plant, etc.

Jan 1, 1963

By Salim Akhtar

The operation of a mineral processing plant with a complex flowsheet is represented by a mathematical operator. Such a representation permits a quantitative evaluation and monitoring of the separation processes in different sections of a processing plant, and gives an overall separation efficiency of the plant.

Jan 1, 1973

By Daniel F. Meyer, William C. Paschen

INTRODUCTION The problems involved with moving millions of tons of rock are being addressed by nationally recognized tunnel contractors who have converged in Chicago over the past 5 years. This wealth of expertise has been needed to meet the risk and challenge of constructing the world's largest network of underground tunnels which in turn has required a dramatic advance in the art and science of tunneling. These pioneers, through innovation, adaptation, and hard work, have eliminated the one major concern of The Metropolitan Sanitary District of Greater Chicago - how to move 8 million tons of rock. The Metropolitan Sanitary District of Greater Chicago (MSDGC) serves 122 municipalities covering 866 square miles in Cook County, Illinois. Of these cities, towns, and villages, 53 have combined sewer systems. On an average of once every four days, these systems overflow about 4 million gallons of combined sewage and rainwater into the area's rivers and canals. The overflows occur at approximately 640 outfall locations of which 10% are owned by the MSDGC, with the remainder of the points belonging to various other municipal bodies. All those who own these "point" sources of pollution are in violation of Illinois State and Federal regulations. To enable its member municipalities to come into compliance with State and Federal law, the MSDGC is implementing its Tunnel And Reservoir Plan (TARP). TARP is a regional solution to the problem of combined sewer overflow in the metropolitan Chicago area. TARP will greatly reduce the pollution of area waterways by intercepting the combined sewage and rainwater carried in the existing sys-

Jan 1, 1981

By A. D. Trippel

The Cripple Creek Mining district is located in Teller County, Colorado, 30 km west of Colorado Springs and 9 km southwest of Pikes Peak (Fig. 1). Since its discovery in 1891, the district has produced almost 21 million tr oz of gold (Gott et al., 1967), most of which has been from high-grade vein deposits. Globe Hill is located in the northern part of the district (Fig. 2). Production from its summit has yielded over 100,000 tr oz of gold. Early production was concentrated along high-grade veins and fault structures, but emphasis was soon placed on the extensive, low-grade (0.0X oz/t), breccia-hosted mineralization. From 1977 to 1981 Newport Minerals, Inc., a subsidiary of Gold Resources, Inc., mined 680,000 t of low-grade gold ore from the Globe Hill pit (Fig. 3) and production is expected to resume in 1986. These strongly-altered and -oxidized breccias are amenable to bulk-mining methods, and thus similar deposits are currently being sought elsewhere in the district. Numerous publications and reports discuss the breccia-hosted mineralization at Globe Hill. They include Cross and Penrose (1895); Argall (1905, 1908); Lindgren and Ransome (1906); Keener (1962); Peters (1982); Thompson, Trippel, and Dwelley (1985); and Trippel (1985). This preprint is a summary of the recently-completed research documented by Trippel (1985).

Jan 1, 1986

By C. I. Wilmot

FMC's Paradise Peak Mine was discovered in July 1983. The deposit at discovery contained 11,340 ,000 tonnes (12,500,000 tons) of ore grading 3.71 glt (0.108 oz/ton) Au and 120 glt (3.5 oz/ton) Ag. A feasibility study was completed by Davy McKee in May 1984, with detailed engineering starting in June 1984. Construction of the facility started on January 2, 1985 with plant start-up taking place on April 14, 1986, two and one half months ahead of schedule and more than 10% under budget. This paper describes the status of the operation approximately 1-1/2 years after start-up including revisions and additions to equipment and process.

Jan 1, 1988

By Daniel J. Brunner

The U. S. Department of Energy (D.O.E.) requires that the prospective nuclear waste repository in Basalt at Hanford, Washington, comply with State of California mine and tunnel safety orders. These regulations require that all main fans be installed in such a manner as to permit prompt reversal of airflow. This paper evaluates the requirement of air reversal and the appropriateness of imposing such regulations on the proposed nuclear waste repository in Basalt.

Jan 1, 1988

By P. C. Holloway

La Oroya zinc ferrite (19.5% Zn, 26.6% Fe, 0.052% Ga, 0.075% In) was roasted with coal under conditions more oxidizing than normally used in a Waelz kiln, and the roasted residues were leached with 200 g/L H2SO4. Overall zinc recoveries of up to 97% were achieved, with 35% of the zinc reporting to the fume after roasting at 1,100°C with a bituminous coal addition of 20%. Under these conditions, 93.2% of the Cd, 13.4% of the Cu, 33% of the Ga, 61% of the In and 18.2% of the Pb were recovered either in the fume or in the leach solution. At 2006 metal prices, the value of the recovered metals is comparable to that obtained from commercial Waelz kiln processing of this residue. Zinc in the franklinite (ZnFe2O4) mineral is reduced to zinc vapor, and, after oxidation, some of the zinc is found as ZnO or as Zn2SiO4 in the roasted residue. Iron reacts to form either hematite (Fe2O3) or magnetite (Fe3O4), with no metallic iron detected in the roasted residue, and less than 2% of the iron is solubilized during leaching. The residue produced after roasting and leaching is, therefore, much more stable than the residue from Waelz kiln processing and should be suitable for disposal in a landfill.

Jan 1, 2008

By D. J. Miller

Environmental considerations are extremely important in planning and carrying out mergers, acquisitions and real estate transfers. It is not inconceivable that potential or actual environmental liabilities could exceed the targeted company's net worth or the book value of the real estate of interest. It is therefore essential that an environmental due diligence investigation (DDI) be performed to quantify environmental liabilities before sales, mergers or acquisitions. This paper will discuss general procedures used in environmental due diligence investigations. The emphasis will be placed on mergers and acquisitions. It should be pointed out that the procedures discussed in this paper are general and must be modified to fit each particular merger or acquisition under consideration.

Jan 1, 1988

By J. M. Cases

Diffuse - reflectance Fourier - transform infrared spectroscopy, Hallimond tube flotation and microelectrophoresis have been utilized to investigate the reactions involved in the adsorption-abstraction of K-amylxanthate on finely ground galena and pyrite. In order to work under well-controlled conditions both minerals were wet ground in a specially built laboratory stainless steel or iron mill. Four surface products were found to be formed on galena: monocoordinate lead xanthate, non-stoichiometric lead xanthate, dixanthogen, and amyl carbonate disulphide. Only dixanthogen was observed on pyrite after using stainless steel rods, while ferric iron xanthate was found when iron rods were utilized.

Jan 1, 1989

Relatively lower recoveries (60%) of coarse phosphate (-16 +35 mesh) particles are attributed to the difficulty in transportation of coarse particles from the pulp to the froth column and rapid drainage of these particles from the froth column to the pulp. Increasing the hydrophobicity of coarse particles by higher, more efficient coating of the collector and using larger froth volumes have been suggested to overcome these problems. In this study, the role of emulsification of the fatty acid-fuel oil collector on the flotation recovery of coarse particles was examined. It was determined that emulsification can not only increase the coarse particle recovery, but do so at higher fractions of fuel oil in the collector, thereby reducing the reagent cost as well.

Jan 1, 1989

By M. D. Baker

Coal-water slurry preparation requires fine grinding and cleaning of coal by flotation. Finer grinding leads to increased ball wear and its effect on the surface properties of coal becomes of concern. Marked ball wear tests were performed to study the effects of oxygen, pH, the soluble species of coal and the addition of pyrrhotite on ball wear. The synergistic action of coal and oxygen greatly enhanced the corrosion of mild steel balls during grinding. Electrochemical measurements on a mild steel electrode in coal slurries and SEM observations of grinding ball surfaces were carried out to explore the corrosive wear mechanism.

Jan 1, 1989