Search Documents

By Charles E. Dandois

New is a relative term, and, when used with reference to a concept as old as shaft kilns can be applied to a number of designs. In this case the design that is the subject of this paper, is known as the ring or annular shaft kiln as developed by Mr. Karl Beckenbach of West Germany. The first&apos; operating unit was rated 185 tons per day and was installed in 1962. Today, there are approximately 84 units in operation in Western Europe and Japan. Twenty-one additional units are in the process of erection or on order. Developed sizes range from approximately 100 to 330 tons per day. Units of over 500 tons are in the design stage, however, the largest units presently operating are rated 330 tons per day, <the first: of this size having been installed in 1966. "Figure" 1 is an elevation view of the unit. It is a single vertical cylinder to which are attached the required service platforms, combustion chambers, injectors and distribution piping. Auxiliaries such as recuperator, exhaust fan and dust collector are mounted on the appropriate service platform. The charging pan, feed conveyor, etc. are mounted at the kiln top. At the bottom of the kiln is the silo with a vibrator type discharger, and mounted separately is the required blower for injector air and fan for internal cooling.

Jan 1, 1973

By MEHMET ALI RECAI ONAL, MAHMUT CAMALAN

The key motivation of this study is to evaluate the potential of well-known hazardous gases—carbon dioxide (CO2), hydrogen (H2) and oxygen (O2)—as grinding aids for mineral liberation in ball milling. The results show that exposure of chromite ore particles to CO2 flow will promote chromite liberation at breakage and, therefore, using CO2 as a grinding aid may partially reduce the carbon footprint of the mining industry. For that purpose, the use of two-phase (gas–solid) or three-phase (gas–solid–water) moving-bed mixers are recommended for the pretreatment of mill feed before ball milling.

By Gilman Y. Murray

The problems connected with the development of economically acceptable water supplies in arid regions are discussed. The techniques for capture and retention of runoff from infrequent desert storms are described and the major factors involved are emphasized. The exploration and planning for a typical water development in southwest United States is described, including an analysis of capital and operating costs for the proposed system.

Jan 1, 1963

By J. Janin, J. F. Bougard

Development of improved transportation networks in major urban centers has led more and more to underground construction, the only reasonable solution for decreasing surface traffic congestion. Excavations required by these projects usually cause decompression of the surrounding soil mass which results in subsidence of several centimeters. While these magnitudes of subsidence have no consequences in undeveloped areas, they are often unacceptable in urban areas where existing buildings, structures and utilities are endangered. Recent tunneling projects for the extension of the Paris Metropolitan Transit System (R.A.T.P.) underground network were carried out with this in view and gave rise to the development of a number of innovative techniques for minimizing ground decompression and subsidence. As shown in Figure 1, the recent R.A.T.P. expansion program includes a new express metro, 46 km long, crossing Paris from East to West, and the extension of many existing metro lines in the suburbs. From the start, R.A.T.P. was faced with many unique technical problems for which there was little precedent experience. The structures to be built have large dimensions, with cross-sections typically ranging from 40 to 300 m2, and exceptionally to 600 m2. The new lines are often very deep because the shallow profile is already congested by the existing metro, interceptors, sewers and a very large number of utilities. As a result, new construction is often below ground water level by as much as 20 m. Moreover, the geology varies widely from hard limestone with compressive strength over 1500 kg/cm2 to inconsistent water bearing sand. Finally, curves in the East-West line must have a minimum radius of 500 m which frequently forces the alignment to pass below existing structures, buildings and monuments.

Jan 1, 1974

As opposed to a prescriptive-based design, a performance-based fire-protection system design allows the system planner the flexibility in choosing specific method, materials and design tools to achieve a preset goal. A different approach in fire protection and a powerful addition to existing method, the system has been around for many years, and has gone through numerous improvements. Despite its popularity in the building industry, it has not been introduced to the mining industry yet. As mines get deeper, increases in size and complication, mine fire safety system will also become increasingly challenging, a new and proven system should be able to great potential to eradicate many of the problems that are either unsolvable or cost-prohibitive with the traditional method. With increasing globalization and international exchange with other major mining countries a common language/practice also make the performance-based design method a desirable feature in mine fire safety system. This paper will first define a performance-based system, step-by-step design methods, likely impacts on fire-protection practices and possible challenges in implementing the system in US underground mines.

Jan 1, 2011

By C. Flores, L. G. Twidwell, T. S. Jordan

It is well known that manguniferous silver ores containing manganese intimate) associated with silver are not amenable to conventional extraction methods. The segregation process has been applied primarily to the recovery of copper from oxidized and oxide-sulfide ores. A new alternative process, consisting of segregation roasting followed by flotation to recover the silver from refractory manganiferous silver ores, was studied using a 23-factorial experimental design. Laboratory investigations were conducted on a manganiferous silver ore analyzing 0.02% copper, 0.09% lead, 0.33% zinc, 12.55% manganese and 187 g/t silver. The investigation was designed to study the effects of the addition of salts, coke and copper (11) oxide on silver recovery. The results indicated that 79.3% of the silver can be recovered in the absence of copper oxide and 88.4% of the silver can be recovered with a copper oxide content of 1.5% at 750°C, 2% salt (NaCI). 1 % coke and 30 min of roasting. It was concluded that the addition of copper oxide improves silver recovery.

Jan 1, 1996

By A. D. S. Gillies, A. Haghighat

"A study has been undertaken at the Missouri University of Science and Technology (MS&T) limestone Experimental Mine to determine new fans set up and wiring options.to install additional mine ventilation capacity. Selection for main fans has been undertaken according to the mine’s required performance specifications and fan characteristics. Available fans for ventilating the mine are Joy and Alphair axial fans each of 24 kW each and two Spendrup booster fans of 12 kW each. The installation of main mine fans on the surface and underground entails numerous considerations. Design of a ventilation network for the Experimental Mine incorporating surface and booster fans has been accomplished using Ventsim Visual program software. The ventilation network has been separated into two segregated parts. A main surface fan and a booster fan have been used in each segregated part of the network. The mine has had a vane axial Joy fan in place for many years. The Alphair 4800 VAX 1800 full blade adjustable pitch vane axial fan was selected and installed as the other surface fan and eventual replacement for the Joy fan. Main surface fans have been connected individually to booster fans in series. The Alphair main surface fan has been installed vertically. Four different wiring options and related cost estimations for addition of the new main fans to the ventilation network have been considered. The analysis resulted in an innovative steel frame design used to allow the fans, when necessary, to be moved to the side of the shaft so that blast pressures do not damage the blades. INTRODUCTION Main fans are the heart of a mine’s ventilation network and play a key role in supplying required airflow (Haghighat, 2014). The Missouri S&T Experimental Mine has been developed in uniform limestone with few stratigraphic features. The mine floor is approximately horizontal and water drains well. A study has been carried out on MS&T Experimental Mine. Selection of main fans has been undertaken according to the mine’s required performance specifications and fan characteristics. Ventsim Visual computer simulation has been used to assist in design of the ventilation network. Wiring circuits, fan foundations and flexibility have been considered as the three main parameters for surface fan installation at the Experimental Mine. Two surface and two underground wiring options and three surface set up options and related cost estimates for the new surface fan system were investigated. Frequent use of explosives in the mine occurs throughout each year. Flexibility in changing the position of a surface fan is important. A number of options have been considered for the location of a vertical main fan positioned on the upcasting shaft. The mine is used for a variety of purposes and flexibility has a high priority amongst design considerations."

Jan 1, 2015

Not quite a year ago, during a speech to a group of mining professionals in Washington, DC, the subject centered around the long-range importance of conducting research projects and how much that research needs to specifically apply to health and safety matters in our industry. The point was made about the critical need to work together with government, private industry, labor organizations and academia speaking with a unified voice as we all march into the future together. The fundamental benefits of competitive research were mentioned --to improve our quality of life, to develop our energy resources, to achieve a safe and healthy environment and to ensure long-term economic growth. Very importantly, emphasis was given to the natural link that makes my agency, the Mine Safety and Health Administration, and the National Institute for Occupational Safety and Health --NIOSH --the beneficiaries of each other&apos;s findings. Unquestionably, there are lines of separation. The main responsibility of the agency I represent, MSHA, is enforcement of the nation&apos;s mine safety and health laws. But we also have an additional responsibility and that is to coordinate and give priority to research in a never-ending hunt for answers.

Jan 1, 1999

By R. Perlo

"INTRODUCTION Peoples’ and operators’ safety in construction are tightly linked to the engineering choices, as much as the necessity of reducing time and costs of realization. Therefore, it is of paramount importance to address them properly from the earliest stage of the design, identifying the risks connected to the work and the variability of such during the different phases of the project. Risk is often measured as the expected value of an undesirable outcome. Regarding to occupational safety and health, the risk is the likelihood that a person may be harmed of suffers adverse health effects if exposed to a hazard. This combines the probabilities of various possible events and the assessment of the corresponding harm into a single value. However, the actual occurrences are often more complex than a single binary possibility case. In a real case scenario, with several possible accidents, the total risk is the sum of the risks for each different accident, provided that the outcomes are comparable. The semi-automatic tunnel support system along with its erector machine proved to be a solution with improved structural performance, able to reduce the time and yet to deliver an enhanced, quality-aware and safer working environment for the operators. The implementation of the system provides the engineers, the contractors and the owners with an effective alternative option shortlisted in 2015 for the ITA Award for the Safety Innovation of the Year. In a market industry driven by safety and time constrains the efficiency shall be the ultimate goal, in order to provide solutions able to negotiate with the most challenging ground conditions. In this paper, the authors describe the recent developments on regard of this whole new tunnel support system, including design approach and presenting related case histories OFFSETTING THE RISKS Considering the above factors, from the manufacturers’ point of view, an effective way to limit the construction risks is to focus on the material and technological characteristics, their application and the risks related to them including any residual risks. Finally addressing the construction needs also involves time and cost-effective solutions. The path to follow is an integrated approach where the efficient management of the risk is supported by a flexible, user-friendly, and time effective product that is able to provide a safe, reliable and viable solution to address the construction requirements. Therefore, in a market sector driven by safety and time constraints, the efficiency is a key goal, in order to avoid redundancy and yet to deliver a safe working environment able to meet the construction schedule. The safety of all the parties involved is given by stable working conditions, either for the workers, or the operators and eventually the public. Therefore, the solutions provided should ‘strengthen’ the overall condition and such “to limit or to reduce the deformations within acceptable designed limits and to prevent [the tunnel] to collapse” [1: Clause 207.1.4]."

Jan 1, 2018

By Hooman Askari-Nasab, AHLAM MAREMI, EUGENE BEN-AWUAH

In oil sands mining, tailings are voluminous unwanted byproducts generated from extracting the desired mineral from the mined ore. Dyke construction and backfilling activities require well-managed techniques to facilitate progressive reclamation at the earliest opportunity. This directly affects the sustainability and profitability of the mining operation. This research introduces a goal programming framework that simultaneously optimizes the (1) production schedule with limited duration stockpiling and directional mining, (2) dyke construction schedule, (3) size, shape and location of tailing cells and (4) mining and processing production targets. The results show that in creating in-pit tailing-cell designs, decreasing the mining-cell volume and increasing the number of mining cells improves the net present value (NPV) of the operation due to increased operational flexibility.

By Bjorn Olsson

"Heavy impact. High frequency hammering. Extreme abrasion. Building on the experience of owning and operating its own mines, Ovako has developed a deep knowledge of how vital the right steel properties are in withstanding the extreme loads encountered in every part of the drill string. That is why Ovako’s product development process is focused on understanding the specific load cases and manufacturing operations associated with rock tools.The punishing conditions of percussive drilling can push the limits of most materials. And heavy mechanical loads are only the beginning. Highimpact energies at high frequency are a major source of fatigue. High temperatures result from impact energy losses. And abrasive, erosive and adhesive wear are constant risks. Handling any of these varying demands at a single point along the drill string is difficult enough — which makes optimizing for the entire drilling system an extremely complex challenge. Engineering for specific loadsOvako has specialized over many decades in analyzing the dominant loads for each of the parts and components used in rock tools, and testing for individual applications in its laboratories. The most critical fatigue properties are controlled through the steel metallurgy, and supported by performance measurements through extensive rotating bending fatigue (RBF) testing, along with special methods that combine impact load with various wear loads. The result is a fit-for-purpose steel with tightly controlled performance properties, making it possible for customers to precalculate the expected life time of their components for highly automated and repetitive processes Tailoring steels for the processing route.The same levels of control and predictability must be carried through to the customer’s own manufacturing processes. By ensuring minimal variations in chemical composition, everything from heat treatment and welding to automated machining can be carried out with high consistency. With precisely controlled material properties based on an existing processing route and exact load case, customers are able to minimize their total tool production costs while ensuring optimal performance for their end products. Development of Hybrid SteelBuilding on this experience in the mining industry, Ovako has developed a new steel family, known as Hybrid Steel, designed to meet the demands of high-stress, elevatedtemperature applications where mechanical and fatigue strength are critical. Traditionally, steels for these applications are produced by expensive small-batch processes. Hybrid Steel, however, enables high volume production at a competitive cost.The world of steel has traditionally been divided into clearly separated categories of tool steel, stainless steel and lower alloy engineering steel. Hybrid Steel is now challenging that division, offering attractive properties from all three categories."

Jan 12, 2017

By Jiang Su, Michal Uhrin

"The use of composite linings, consisting of permanent sprayed primary and secondary linings with a sandwiched spray applied waterproofing membrane is expected to improve efficiency and reduce lining thickness, but it also brings complex primary-secondary lining interaction. This issue is further complicated by the uncertainty regarding the long-term behavior and parameters of the sprayed concrete–sprayed membrane interface.This paper aims to address this issue by presentation of a series of numerical analyses of a typical shallow SCL tunnel in soft ground with a range of design assumptions on the interface behavior: (1) compression only; (2) compression and tension; and (3) compression, tension, and shear.The results demonstrate that the assumed interface behavior has a significant impact on the primary-secondary lining interactions. A design approach of ignoring the tension and shear bond at the interface may not be conservative particularly for serviceability. This paper explains the rationale behind these conclusions and discusses the implications for design.INTRODUCTIONSprayed Concrete Tunnel Lining SystemsSprayed concrete linings (SCL) have been used in conventional tunneling for decades. However, details of SCL systems may differ to a large extent depending on ground conditions and specific tunneling methodologies.In hard rock conditions, for example, drill and blast excavation is typically supported by rock bolts and sprayed concrete (NGI 2014). Such tunnels are usually designed fully drained and the above-mentioned support elements considered permanent without the need for a further inner liner. Therefore, there is no structural interaction between separate lining shells to consider.In conventional tunneling in the European Alps, a double shell lining is typically utilized, consisting of an outer (primary) sprayed concrete lining and an inner (secondary) cast-in-place concrete lining, separated by a waterproofing system. The primary lining normally includes rock bolts and may include other support elements. The waterproofing system is usually based on a plastic membrane and a geotextile fleece. The tunnel may be designed fully or partially drained or fully undrained. Although there are two structural lining shells interacting, investigation of such interaction is generally irrelevant to designers because the primary lining is considered only temporary (fully sacrificial in the long term). An overview of reasons for this assumption is given, for example, by Lemke (2014). The secondary lining is designed to resist all foreseeable loads on the tunnel. The primary lining may, in reality, interact structurally with the secondary lining during the life span of the tunnel. However, since the secondary lining design must cover all possible (extreme) scenarios, investigation of such interaction does not bring any value to the design."

Jan 1, 2016

By Robert F. Baker

Neanderthal technology is a harsh and inaccurate way to describe modern underground construction and mining practices, but such an exaggeration helps to focus on a major problem or wasted opportunity of modern society. Why is it not safer to excavate in the underground? Why are the working conditions still so unfavorable? Why are urban freeways, shopping malls, warehouses, power plants, sewage disposal treatment plants, and similar facilities still constructed on the surface of the ground--because it is a better location? On the contrary, if underground technology made full use of existing knowledge, underground resources and space would be much more effectively used. And why is the technology so inadequate? Certainly, researchers and practitioners are aware of the shortcomings and are equally aware of problems that have to be overcome. One of the most important reasons has to do with the type of policy goals that society has set in the past. Policy makers may have agreed that improvements would be desirable but no serious commitments have been made--that is, there has been no major allocation of resources to advance these technologies. And yet, to bring about significant changes will require significant time and resources. The resources that are needed are far in excess of what industry can afford to invest, particularly since the pay-off may be far in the future. So the problem reverts to society in general. As long as society is willing to tolerate the present costs and safety requirements for recovering minerals and for constructing underground facilities, then the changes will be slow in coming. Until such time as society sees and desires the benefits

Jan 1, 1974

By M. A. Reinsel

New technology for removal of nitrate from low-temperature waters has been developed. Typical results from the first operational-scale system (operating at a metal mine in Montana since January 1996) are over 90 percent nitrate removal at a flow rate of 130 gpm and a water temperature of 12°C. The system also operated successfully at flow rates as high as 300 gpm and water temperatures as low as 2°C. The ABC is advantageous because it is: a) cost-effective to design, construct and operate, and b) effective at cold water temperatures. The system can be designed for a variety of flows, nitrate concentrations, water temperatures and water qualities.

Jan 1, 1998

By Qinghua Gu, BUQING XUE, XUEXIAN LI, JIANGSHAN SONG, Qian Wang

To solve the problem of time-consuming and low precision in updating the open-pit vehicle transportation network, a high precision road network model construction method for unmanned vehicles in open-pit mines is proposed. This method can be divided into two steps. In the first step, an improved deep learning image processing model named DeepLabv3 + C (DeepLabv3 + Concat) is presented. Then, the road information extracted by the DeepLabv3 + C network is used to construct a three-dimensional model of the open-pit mine road network. In the second step, aiming at the time-consuming problem of unmanned vehicle meeting in open-pit mines, a vehicle meeting strategy was proposed. This strategy is used to guide the navigation of unmanned vehicles in open-pit mines. Besides, the DeepLabv3 + C network is verified by comparing the mIOU (means Intersection Over Union), accuracy, and continuity of road image extraction with the mainstream networks. The road network model constructed in the first step is quantitatively analyzed, and its performance is compared with GPS trajectory clustering methods. At the end of the paper, vehicle running simulation is carried out on the road network model by using Unity (a 3D visualization simulation software). The results show that the road network model constructed by this method can meet the navigation requirements of unmanned vehicles in open-pit mines, and the feasibility of the vehicle meeting strategy is proved.

Jan 11, 2022

By William Mayrsohn

INTRODUCTION The net smelter return (NSR) calculations made on various smelter-refiner alternatives, is usually done by taking the gross metal value less metal deductions, smelter-refiner charges and transportation-insurance costs. An important further step in the calculations is the financial charges imputed by refining time, transportation delays, to the time gold is returned (if tolled) or paid for if bought by the refiner. Metal that is priced in advance of payment also requires a forward premium that the mine may or may not be getting. This is a hidden cost that is often omitted from the calculations. Segmentation of each of the above costs are vital to see where improvements can be made through negotiations, better choice of metal pricing or transportation alternatives. BASIC NSR CALCULATIONS SMELTER-REFINER CHARGES Payable Metals - Treatment Refining Charges: Since these can vary from one smelter to another, the effect of a $25 per ounce price increase/decrease should be calculated and kept in mind. This effect is compared to differences in refining/treatment charge and a total smelter/refiner cost on a cost per ounce of dore, gold, or a dry ton of concentrate. Transportation - Insurance: Research has to be done on transportation alternatives perhaps with some assistance from the smelters, railroads or trucking companies. For dore, the U.S. postal service is viable and inexpensive. For railroads, deal with the regional office ie., B&N El Paso, if production warrants regular bulk shipments. Spot rates tend to be higher. A small mine producing concentrates usually goes to the nearest smelter due to extremely high transportation costs. Here is where a refiner can help. Insurance-Quotes for rates on dore/ concentrates are easily obtainable, but the mine has to shop for the best rates. Your insurance broker is the best source of this information. Differences between Mine and Smelter/Refiners Metal losses can be caused by the following: - Concentrate dry weight differences caused by moisture determination or faulty scales (often at the mine). - Sample bias by poor preparation practices on either side ie., grinding of the sample removing gold; or a poorly mixed concentrate. Dore bullion has no such difficulties.

Jan 1, 1987

By Randall D. Peterson

Strip mining with draglines and other surface equipment has traditionally been the method of choice for mining shallow deposits. This is particularly true for soft deposits that require little or no blasting. High rates of productivity and low operating costs have set this standard. However, these methods can be improved. Strip mining methods are batch processes and difficult to accommodate in processing. Moreover, they are encumbered with overburden removal, reclamation expense, and human inefficiencies. This paper describes the invention of a novel shallow earth mining technique called the Softwall Mining Method. Softwall Mining is an adaptation of longwall mining for loose earth conditions. The method was specifically invented for recovering phosphatic clay ore from beds in North Central Florida, but is likely to be suitable for a number of other minerals as well. Potential deposits for which the method may be well suited include placers, disseminated deposits in soft host rocks, bauxite, soft coals and lignite deposits, and other deposits where overburden will subside readily and where the ore can be hydraulically broken and slurried. Unit operating cost advantages are expected over the current dragline systems used. The Softwall mining advantages are its high rates of productivity, control and automation of the mining process, reduction of dilution and waste, and elimination of the majority of stripping and reclamation.

Jan 1, 1998

By Ihor Kunasz

The high lithium demand forecasted for some high tech applications and batteries for electric and hybrid-electric vehicles, in particular, has sparked increased exploration for lithium, particularly for lithium- and potassium-bearing brine deposits. The latter have generally followed the Canadian Institute of Mining, Metallurgy and Petroleum (CIM) NI 43-101 guidelines on resource reporting, formulated for hard rock deposits (metals and industrial minerals). While a number of the requirements can be appropriately applied to brines, brines are fluids and require a specific analysis leading to a distinct set of reporting requirements. Brines cannot be considered industrial minerals because the various elements occur as ions in a dynamic fluid, rather than being chemically bonded in a solid. Although chemicals are produced from brines, brines have no relation to industrial mineral deposits. This article analyzes the recently released (Nov. 1, 2012) document CIM Best Practice Guidelines for Resource and Reserve Estimation for Lithium Brines, in light of the practical knowledge available from existing brine operations. It recommends modifications to the guidelines, which, if applied in their present format, will result in overstating resources and reserves and mislead potential investors. The CIM Best Practice Guidelines for Resource and Reserve Estimation for Lithium Brines document is generally descriptive and does not fully address the methodology for brine resource or reserve definition. Lithium and other elements (potassium, magnesium) are contained in a fluid, the hydrologic characterization of which should be the principal focus of a brine exploration program. The fundamental requirement in defining lithium brine resources and reserves in a salar is the identification and definition of those formations ? the aquifers ? that will yield brine in a usable quantity to a well, because brines can only be extracted by pumping wells. Fine-grained sediments will never, as required in the summary Table 1, have ?reasonable prospects of economic extraction,? cannot be considered and, therefore, need not be tested. However, the guidelines recommend the collection of solid samples and a high-core recovery for laboratory testing of various sediments instead of focusing on the brine.

Oct 1, 2013

By Sotiris Psomas, Colin M. Eddie

"Steel Fibre Reinforced Concrete (SFRC) Segmental Tunnel Linings have successfully been used for over 20 years in the UK and have been adopted in a number of high profile projects such as High Speed 1, Crossrail, Thames Tideway, as well as High Speed 2. Tunnel linings and especially SFRC design are not covered in the Eurocodes. This shortage of SFRC tunnel design rules seems to be partially addressed by several international publications. However, in the UK, the ‘design-assisted by testing’ (DAT) approach has also been adopted. The Paper discusses the UK’s best design practice and focuses on the DAT methodology as applied in the case of the 6.9km (4.3miles), 7.8m (25.6 feet) ID Lining for the £635million Lee Tunnel Project. The design approach, the full scale testing at the Building Research Establishment (BRE), and the construction innovations are presented. This experience will be transferred to the £4billion Thames Tideway Tunnel.INTRODUCTIONSteel Fibre Reinforced Concrete (SFRC) has been used for Tunnel segments for more than 20 years. The first application of SFRC in the UK was for the Heathrow Baggage tunnel (1994). Since then significant size tunnels have been designed and constructed, such as the Jubilee Line (1999) High Speed 1 (CTRL, 2006), Crossrail (2014), Lee Tunnel (2014) and the scheduled 25km Thames Tideway (‘Super Sewer’) and High Speed 2 rail tunnels. However one the main obstacles in achieving streamlined design and improving efficiency are the lack of appropriate design guidelines for SFRC tunnel segments. This issue will – to some extent – be addressed by a number of current documents on tunnel FRC design either being produced by BSi (PAS8810, expected 2016), ACI (544.R) and ITAtech (Design Guideline PCFRC, 2015) in an effort to advance the design of SFRC and take into consideration the recent developments in Steel and Macro-Synthetic FRC technology."

Jan 1, 2016

By Robert D. Hansen, Basil S. Fee, Richard R. Klimpel

Despite the importance of froth flotation to the mineral industries as a means of separating various minerals, the commercial flotation reagents used have varied little in the last twenty years. Numerous articles and books are available describing existing flotation chemistry and its application, e.g., Fuerstenau (1962), Fuerstenau (1976), Aplan (1980), Somasundaran (1980), King (1982), Leja (1982), Ackerman, et. al. (1984), Crozier (1984), Hansen and Klimpel (1985). There are many reasons for this lack of significant new reagent development including the general utility and relative cheapness of collectors, such as xanthates, and frothers, such as methyl isobutyl carbinol and the glycol ethers. Another important reason is the inherent complexity of the flotation process itself coupled with highly variable and difficult to standardize feed materials which make reliable reagent comparisons difficult and seriously limit the use of theoretically based studies to "predict" new or optimal reagents. In addition, the higher cost of "specialty flotation reagents demands that their performance attributes be significantly greater than existing general all- purpose commercial reagents – something often difficult to prove in practice. Faced with this situation, a detailed applications research pro- gram [Klimpel (1980 ab, 1982, 1984 ab), Klimpel, et. al. (1982)] was organized from 1979-1985 on mineral flotation with the following goals: 1) the development of appropriate batch laboratory flotation testing techniques sensitive enough and statistically reliable enough to identify small differences in performance between different flotation tests (i.e., between various reagents, even those with relatively minor chemical structural changes); 2) the identification of mathematical models with appropriate numbers and types of parameters that have maximum statistical power to statistically distinguish between various time-recovery profiles; 3) the generation of laboratory and corresponding plant scale data in sufficient quantity and consistency so that the highly interactive nature of the "flotation system9&apos; of chemistry/ equipment/operating conditions could be quantified; and 4) the invention and development of really new and unique reagents for giving improved flotation performance. The goal #1 was achieved [Klimpel (1980b. 1984b), Meyer and Klimpel (1984)l by basically using a simple automated paddle device for consistent

Jan 1, 1986