Search Documents

Following a disaster in a mine, it is important to understand the state of the mine damage immediately with limited information. Computational fluid dynamics can be used to simulate and ascertain information about the state of ventilation controls inside a mine. This paper describes a simulation of tracer gas distribution in an experimental mine with the ventilation controls in various states. Tracer gas measurements were taken in the lab experimental apparatus, and used to validate the numerical model. The distribution of the tracer gas, together with the ventilation status, was analyzed to understand how the damage to the ventilation system related to the distribution of tracer gases. This study will be used in future research in real mine measurements to compare collected and simulated profiles and determine whether damage to the ventilation system has been incurred during an emergency situation, the nature of the damage and the general location of the damage.

Jan 1, 2011

By G. Krogman, C. Walla, B. Wood

The Gebo Mining District (District) is located in the Bighorn Basin of Wyoming. Commercial underground coal mining began in 1906 with the arrival of the railroad in Thermopolis, which is located approximately 11 miles to the south. Mining in the District ceased by the early 1970’s. In Fall of 1999, Lidstone and Associates, Inc. (LA) and their subcontractors were retained by the Wyoming Abandoned Mine Land Division (WyAML) to perform an inventory of over 500 abandoned mine sites across Wyoming. During the summer of 2000 field inventory, a 30-foot deep headcut (Figure 1) and sink-hole were noted in the West Fork of Sand Draw (WFSD), immediately west of the Town of Gebo. The headcut and sink-hole were located at the culvert outfall associated with a stream crossing of a relatively well traveled county road. Upon further investigation, it appeared that underground mine workings had been exposed at this location. This resulted in a condition whereby water would be conveyed directly into the mine workings during a runoff event. The exposed mine workings as well as stream capture created a very hazardous condition. The WyAML implemented mitigation measures in the summer of 2000 by constructing a temporary stream crossing upstream of the existing failed crossing. To address this hazardous situation as well as a number of other hazards identified in the District during the field inventory, the WyAML retained PHC Reclamation, Inc. (PHC). PHC was directed to perform a field investigation and develop a Reclamation Plan to address all existing abandoned mine hazards in the District. Federal, state, and private parties own lands within the District. Hazards identified during the investigation included an underground mine fire, open adits, open shafts, subsidence, drainage problems, and coal slack. A Report of Investigation (ROI) was submitted to various regulatory agencies that documented the existing conditions and conceptual reclamation plans to remediate the hazardous conditions. After review of the ROI by the US Department of Interior - Bureau of Land Management (BLM) an on-site meeting was conducted. BLM Cultural Resource personnel declined to approve a District reclamation project until a historical overview of the entire District was prepared. Due to the hazardous situation associated with the WFSD stream crossing, Hot Springs County Road and Bridge Department convinced various state and federal regulatory agencies to allow reclamation of the stream crossing to occur. A decision was made to allow reclamation on privately owned lands within the WFSD drainage. This decision limited the amount of channel that could be subjected to reclamation upstream of the crossing to privately owned lands. PHC contracted LA to perform a geologic, geomorphic, hydrologic, and hydraulic investigation of the drainage to assist in the development of a WFSD reclamation plan. LA’s investigation consisted of four parts: Delineate the extent of mine workings in the area; Identify all drainage structures that required mitigation; Survey a series of channel cross-sections and a longitudinal profile of the impacted channel; and, Develop basin hydrology to assist in the design of a stable reclaimed stream channel.

Jan 1, 2006

By Allan M. Johnson

The Sherwood Mine is being monitored to determine the nature and extent of changes in the mine and its environs which result from the closing and the cessation of pumping. Of particular interest was the possibility of piping-induced subsidence occurring as the mine flooded. Previous experience in the district indicated that this possibility was very real. A monitoring system, including acoustic sensors, extensometers, surface subsidence monuments, and ground water observation wells was installed in July 1978, just prior to the mine closing. Late in 1979, three piping-induced subsidence events occurred. The monitored data, and related laboratory studies are being applied to a quantitative description of piping-induced subsidence.

Jan 1, 1980

By C. E. Capes

The continuous balling? operation whereby a moist particulate mass is tumbled in a horizontal revolving drum with recirculation of the undersize product can be extremely unstable. Product and recycle rates are subject to wide fluctuations. Although the problem seems to be well-recognized, there is little published information or quantitative data readily available, especially in relation to industrial-scale circuits. Probably the best available published results are in the Russian literature, an illustration of which is given in Figure 1. These data, taken from a study') of some of the factors which influence the stabilization of the pelletizing process, illustrate the wide variations in circulating load and circuit productivity which may be encountered over a period of operation. The problems of balling circuit stability may be traced to random seed or nuclei generation and uncontrolled agglomerate growth. The situation is analogous to that in crystallization processes where (4 considerable attention is given to nucleation control. Traditionally attempts have been made to optimize system and operating variables to stabilize the balling process. A supplemental approach which is taken here is to build on the considerable

Jan 1, 1975

By Wayne C. Smith

Both water pollution and proposed solid waste disposal regulations have a definite effect on the copper leaching industry and some of the major factors affecting the industry are discussed in this paper. New developments of the NDPS are discussed with emphasis on the "toxic" or priority pollutants and EPA's philosophy on the control of these pollutants, The protection of groundwater is the prime aim of RCRA through solid/hazardous waste management. Some of the major elements of the RCA regulations that will affect the copper leaching industry are discussed.

Jan 1, 1980

By E. Ashworth

A thermistor probe has been developed to measure in situ temperature profiles underground. A full description of the probe is given. Data collected from the probe has been used to compare the actual profiles with those predicted from a finite element analysis using laboratory measured thermal properties of the different rock types. This comparison indicates the applicability of laboratory measured parameters in modeling the real conditions. Factors such as applied pressure, moisture content and anisotropy on laboratory measurements is discussed.

Jan 1, 1983

By W. M. Luff

The Brunswick No. 12 Deposit is a large polymetallic massive sulphide deposit, occurring in Ordovician age rocks of the Tetagouche Group. Silver is contained within the sulphide zones and economically it is the second most important commodity produced. Brunswick is one of the largest silver producers in Canada. The distribution of silver within the mine is presented, with examples from various levels. The concentration of silver can be shown to be related to both stratigraphy and structure. The mineralogy of silver in mill products is also presented.

Jan 1, 1986

By M. A. D. Azevedo, J. D. Miller, R. Kobler, E. Mutkowska

Up to 3 million tons of automotive shredder residue (ASR) is generated annually in United States. Plastics are the most valuable component of the ASR material making up approximately 25% of the total weight. In order to reuse these plastics, a selective process is required to separate each plastic, with very high purity and favorable economics. One separation technique, which may be able to selectively recover the plastics from ASR, is flotation. The preliminary flotation results have demonstrated that acrylonitrile-butadiene-styrene (ABS) and polycarbonate (PC) can be selectively separated from the model ASR feed, the PC/ABS/PA 66 system, by appropriate control of the surface chemistry.

Jan 1, 2001

By Keith E. Dyas, John Nelson, Ronald T. Johnson

GENERAL DESCRIPTION The Bruce mine of Cyprus Mines Corp. is located in Bagdad, AZ. The mining method used is open cut-and-fill. Of the annual production of 81 647 t (90,000 st), approximately 83% is taken from load-haul-dump (LHD) stopes and the balance from slusher stopes. All ore is produced from the area between the 1250 level and the 2300 level. The average travel time from the shaft pocket to the stope is approximately 5 min. GENERAL ORE BODY REQUIREMENTS AND LIMITATIONS Size, Shape, and Dip The Bruce ore body occurs in quartz-sericite schist with Dick rhyolite on the footwall and andesite on the hanging wall. Diabase dikes are found in the hanging wall; there is also a dike coming off the footwall and crosscutting the ore body. All of the rock types are of the Precambrian Yavapai series and have been subjected to regional metamorphism. A composite of the ore body is given in Fig. 1. The deposit is of massive sulfides occurring as a steeply dipping replacement body. On the upper levels the ore is veinlike with widths from 0.6 to 4.6 m (2 to 15 ft), dipping at 1.4 to 1.5 rad (80° to 85°). On the lower levels the ore is dipping from I to 1.2 rad (60° to 70°) with widths from 3 to 16.8 m (10 to 55 ft). The strike length varies between 107 to 183 m (350 to 600 ft). The rhyolite footwall generally has a knife-edge contact with the massive sulfides. The exceptions to this are the upper levels where there is a 1.5 to 3 m (5 to 10 ft) band of silicified sericite schist between the sulfides and the rhyolite. In the southern part of the ore body the hanging wall is tuffaceous andesite and andesite. In this area the contact is generally sharp and easy to follow. However, to the north there is a large chlorite schist zone that crosscuts the bedding and comes in contact with the massive sulfides. This is apparently due to hydrothermal alteration of the andesite. The chlorite schist is highly mineralized with chalcopyrite and pyrite and quite often forms economic pockets of ore. In the massive sulfides the chief ore minerals are sphalerite and chalcopyrite. Pyrite is the predominant sulfide with considerable pyrrhotite throughout. Bright arsenopyrite ouhedrons in fine grain massive sulfides are quite common. Occasionally small amounts of galena are seen, usually near the foot or hanging wall contacts. On rare occasions tennanite is associated with massive arsenopyrite. Minor amounts of quartz, calcite, and un¬replaced remnants of sericite schist occur, but essentially pyrite is the gangue in which the ore minerals occur. The ore values are in excess of 3.5% copper and 12.5% zinc with some silver and rare gold as byproducts. Ground Conditions The massive sulfides are generally self-supporting. One exception is in the 1850 stope where the ore body is 9 to 11 m (30 to 55 ft) wide and 152 m (500 ft) long. There are flat to shallow dipping slips and seams in the ore, creating extremely blocky ground. For support, old 25.4-mm (1-in.) hoist ropes were installed tensioned to 27 t (30 st), and then cement grouted over the entire length in longholes [14 to 15 in (40 to 50 ft) in length) drilled on 3-m (10-ft) centers from the level above. This has tied the formation together very successfully and virtually eliminated the blocky ground condition. Both the hanging wall and footwall are quite shaley in some areas. Reasons for Adopting Trackless Open Cut-and-Fill Methods First, any method other than open cut-and-fill would have caused too much dilution. The use of rubber-tired mining equipment in the pro¬duction stopes requires a footwall ramp. The inclines in ore will be mined out, so this ramp in the footwall will provide access to and from the stopes (Fig. 2). This incline is very expensive, but necessary to convert existing stopes to LHD mining. 'The final cost of ore mined by the LHD machines has not been determined. As of 1972, tons per manshift in the 2150 stope-the only one to complete a full cut-had increased from 7.58 t (8.36 st) to 12.83 t (14.14

Jan 1, 1982

By Cheryl Lee Vatter

The Lupin mine consists of a gold mining, milling, and refining complex located 400 km (250 miles) northeast of Yellowknife and 100 km (60 miles) south of the Arctic Circle on the southwest shore of Contwoyto Lake in Canada's Northwest Territories. (Fig.1). The mine was commissioned in 1982 and is presently producing 6 t/a (193,000 oz per year) of gold from 612 kt (675,000 st) of ore. The success of this operation is due to such factors as the continuity and grade of the ore body, the competency of the host rock, low mining costs, efficient milling, the transportation of people and materials to and from the mine site, and the unique work schedule resulting in a stable workforce. Echo Bay Mines operated a silver mine at Port Radium on Great Bear Lake, Northwest Territories, from 1965 to 1982. The company first obtained an option on the Lupin property from Inco in February 1979 and completed an underground exploration program in 1979-1980. Topographic relief is low and vegetation is sparse in the continental subarctic climatic zone, consisting mainly of moss and lichens. Temperature extremes are from 24°C to - 45°C (+75°F to -49°F) with an annual mean of -12°C (+54°F). Permafrost extends from near surface to 500 m (1640 ft) in the ore zone. Its remote location and harsh climate presented some challenging design and logistical problems. Construction began at the Lupin mine site in 1980. Before construction, a 1.5-km (5000-ft) gravel landing strip was prepared, suitable for landing a C 130 Hercules. The entire Lupin project took 20 months to build. All of the men and materials were transported to the site with some 1100 Hercules flights and several hundred Convair 640 flights. The Convairs transported construction crews, which numbered 400 at their peak, and also carried 3.2 kt (3535 st) of supplies during construction. The facilities were constructed and commissioned for a total cost of C$135 million. The operation was originally designed to throughput 860 t/d (950 stpd). Expansion in 1983, circuit refinements, and some capital projects brought the daily throughput to 1.7 kt/d (1850 stpd). The underground mine delivers 612 kt/a (675,000 stpy) of ore to the mill at an average head grade of 8.46 g/t (0.3 oz per st). The ore is nonrefractory and is processed in a conventional cyanide leach using the Merrill Crowe process. Gold recovery is about 95.0%. The average production cost is $US5.85/g ($US 182 per oz) based on 1987 figures. Mining at Lupin – Geology The Lupin deposit occurs in amphibolite grade iron formation overlain by mudstones (phyllites) and underlain by graywacke (quartzites). Contacts between the wallrock units and the iron formation are well defined. It has been folded and tilted into a megascopic antiform-synform-antiform structure (Fig. 2). Gold occurs primarily within the sulfide rich iron formation, with some minor occurrences in sulfide poor iron formation. The distinction between sulfide rich and sulfide poor iron formation is based on a visual cutoff of 5% total sulfide content. Mining widths are determined by an assay cutoff of 4.2 g/t (0.15 oz per st) gold. There are few tons between 1.7 and 4.2 g/t (0.06 and 0.15 oz per st). The amphibolitic iron formation at the mine ranges from 1.5 to 20 m (5 to 65 ft) wide and has been followed over a strike length exceeding 1.7 km (5600 ft). The wider portions of the ore body tend to occur at its north extent and south nose. The gold-bearing iron formation appears on plan as a Z-shaped structure made up of three zones: the West, Center, and East. The West and Center zones dip steeply to the East (75° to 90°). Each of the ore zones plunge at an angle of about 65°. Total strike length of the three zones is more than 610 m (2000 ft). The zones are confirmed at a depth of 650 m (2130 ft) below surface. The Center zone is the widest and varies from 4.5 to 20 m (15 to 65 ft) while the West is the narrowest, averaging 1.5 m ( 5 ft). The footwall is comprised of quartzites that are strongly jointed and locally grades into phyllite, which comprises the hanging wall. The hanging wall and footwall are reversed in the West zone. Mineralogy of the ore at Lupin consists of amphibole minerals (hornblende, cummingtonite, and grunerite), feldspars, quartz, occasionally garnet, pyrrhotite, arsenopyrite, minor pyrite, and trace chalcopyrite. Also found in minor amounts are scheelite, apatite, epidote, calcite, tourmaline, and some arsenides (notable loellingite). Quartz

Jan 1, 1989

By E. R. Pantos

US coal production increased 3% to a record 832 Mt (917 million st) in 1987, according to preliminary Energy Information Administration (EIA) data. Most of the increase was due to the unusually warm summer and the increased coal-fired electricity demand for air conditioning. Drought conditions in the Northwest lowered hydroelectric generation, contributing to the higher use of coal by electric utilities. However, excess production capacity and increased competition from natural gas added further downward pressure on delivered coal prices, continuing the declining price trend of the last several years. Coal production by region Appalachian coal production reached 402 Mt (443 million st) in 1987. This is about 3% more than in 1986 and just short of its 1984 peak. Virginia produced 7% more than its 1986 level, due to increased coal-based electricity demand. Smaller percentage increases were attained in eastern Kentucky, Pennsylvania, and West Virginia. Ohio and Alabama were the only major coal-producing states in Appalachia that produced less coal in 1987 than in the previous year. In the Interior region, 1987 coal production reached a record 182 Mt (201 million st), about 2% above 1986. Illinois is the largest coal-producing state in that region. Production there fell about 3.7%, primarily because of lowered demand at electric utility plants in Alabama and Tennessee. However, this was more than offset by production increases in western Kentucky, Texas, and Indiana. After falling slightly in 1986, coal production in the West resumed its upward trend to a record 248 Mt (273 million st). Wyoming is that region's dominant coal producer. It mined 7% more coal than in 1986. Wyoming's increase offset the 11% decline in New Mexico production and smaller declines in other Western states. Coal consumption and prices Domestic coal consumption reached a record 759 Mt (837 million st) in 1987. Most of the increase resulted from the unusually warm summer that led to higher than normal peak demands for electricity in the third quarter. Electric utility coal consumption was also boosted by the below-normal hydroelectric generation that resulted from low water levels in the Northwest. These factors more than offset the effects of increased nuclear power generation and competition from natural gas. As a result, coal provided 56.9% of electric utility generation in 1987, compared with 55.7% in 1986. Electric utilities consumed a record 651 Mt (718 million st) of coal. While electric utility coal consumption increased, the average cost of coal to utilities was down, from $1.58 per million Btu in 1986 to $1.52 in 1987. The average price of coal delivered to utilities in 1987 was $35.09/t ($31.84 per st), the lowest since 1981. Coal prices were held down by a glut of coal supplies and by a decline in the average price of natural gas to electric utilities. Coal consumption at coke plants in 1987 was 2.6% above the 1986's 32.5 Mt (36 million st). This increase reflects steel's recent resurgence. Coking coal demand, though, was reduced by the increased use of continuous casting and electric furnace technologies. The average price of coal delivered to coke plants fell from $56.02 to $51.35/t ($50.83 to $46.59 per st). Coal consumption in the industries other than coke plants amounted to 68.2 Mt (75.2 million st) in 1987, slightly less than in 1986. Coal lost part of its market share to natural gas, which was priced favorably relative to coal. The average price of coal delivered to manufacturing plants was at its lowest level of the current decade. It fell from $39.50/t in 1986 to $37.27/t ($35.84 to $33.81 per st). Residential and commercial coal consumption fell to 6.2 Mt (6.9 million st) that is 9.8% below 1986 and the lowest since 1980. This decline is also attributed to the relatively low price of natural gas in 1987. Coal stocks Coal consumers held 169 Mt (186 million st) of coal stocks at the end of 1987, 5.9% above the 1986 year-end level. Most of this increase was due to stockpiling by electric utilities in anticipation of a possible strike by the United Mine Workers of America early in 1988. Stocks at electric utilities increased to an estimated 154 Mt (171 million st) at the end of 1987, 5.6% higher than the previous year. This was much lower than 1984's stock buildup. Coke plants increased their coal stocks by 30% in 1987 to 3.5 Mt (3.9 million st), rebounding from the unusually low inventories of 1985 and 1986. Other industries increased their stocks slightly in 1987. Coal producers and distributors ended 1987 with 25 Mt (28 million

Jan 5, 1988

By Keith A. Yarborough

INTRODUCTION The National Park Service (NPS) conducted a research program from mid-1975 to early 1978 to measure alpha radiation levels in natural caves which it administers. Subsequently, a long-term management program was developed which has conducted routine monitoring of radiation levels and has computed employee exposure accumulations in certain NPS caves. The overall program: research and management; was undertaken to evaluate the possible health hazard to cave visitors, interpreters, researchers, maintenance personnel, concessions employees and other workers and to protect their health. The results of this work have been reported extensively elsewhere (see References 1 through 3, 5, 6, 9 through 13, and 14 through 26). This paper deals with the relation of radon gas and daughter produced radiation levels to the cave air flows which mobilize them. These flows are a function of interior cave and exterior ambient air temperatures and pressures and of the cave's geophysical configuration. The low-level, ionizing radiation is produced by minute concentrations of radon and thoron gases which emanate from within caves. Because of confinement, the radiation levels are often appreciably higher than in surface atmospheres. Subsequent radioactive disintegration of the gases into their ionized "daughter" products, which are particulates, permits distribution of the alpha radiation throughout a cave system. The extent and character of this distribution depends upon the particular cave and the air flows which it produces. Thus, the alpha radiation serves as a "tracer" to describe the flows. The flow analysis is divided into two parts: 1) A qualitative description with respect to the two basic geophysical cave types over both long-term (annual) and short-term (diurnal to weekly) periods. 2) A quantitative description of the unsteady, uniform and non-uniform, one-dimensional, incompressible motions for both influent and effluent air flow situations in both basic geophysical cave types. A part of the qualitative description presents "Special Measurement" data: Tsivoglou [vs.] Kusnetz working levels, Tsivoglou individual daughter levels and free ion concentrations, radon gas concentrations, and equilibrium ratios. A great deal of important work has been carried out by Mr. Bobby C. Carson, Cave Radiation Technician at Mammoth Cave National Park, Kentucky. He reports these findings later in this conference (Ref. 6). Some of his results have been used here to establish the cave air flow analysis. Other National Park Service personnel have made measurements at others of the caves for which data are reported here. All of this work and cooperation has been vital to the success of this research program. It is very much appreciated. THEORETICAL FLOW DESCRIPTION Previously reported research (See Ref's. 20, 21, 23 and 25) has established the qualitative relationship between the alpha radiation in caves and their natural air flows. The radiation serves as a representation of these air flows. Changes in radiation with time represent changes in the main forces which produce the air flows. The quantitative data have substantiated that [all caves in which the primary cause of air flow is due to temperature produced gravity (density) gradients and also having minimal man-made disturbances, experience seasonal variations in airborne alpha radiation. The radiation levels increase in summer but decrease in winter], based upon seasonal air movements through each cave system which occur naturally. Two general types of physical cave configurations which control the air flows have been identified as: 1. Those which go up into a hillside or mountainside: Type I ("Upside-down" = USD). 2. Those which go down into the earth; Type II ("Right-side-up" = RSU). These act to control the air flows seasonally. The summer increase in Type I caves is due to increased air flows, whereas in Type II caves it results from stagnation or reduced air flows. This seeming paradox is explained by the physics of the air flow regime in each cave type and has been detailed elsewhere [Ref's. (20), (22) through (25)]. It[ i] true, in general, that air flow decreases airborne radiation in the [immediate vicinity] in which it occurs. Any paradox results from subsequent distribution throughout the case as to [ how] the air moves through a cave [system] with respect to time and space. Exceptions to the cave air flow "rule" are: 1. Caves in which pressure gradients and pressure fluctuations [predominate] in producing the air flows. 2. Caves in which man-made effects and management practices are superimposed on the natural air flow regime. Man-made disturbances which can alter the natural cave air flows are tunnels, elevator shafts, bore holes, sealed and closed portals, etc. If these are not properly sealed, the natural air flows which they change will totally alter the distribution and seasonal variations of the alpha radiation levels. These exceptions may act separately or in combination.

Jan 1, 1981

By N. S. Kim

Silver paste including nano sized particles maintains conductivity in high temperatures without forming oxide layers. In the industry, printing process produces wasted silver paste inside the cylinder and on silk-screen. Pyrometallugical silver recycling methods have environmental problems and do not extract pure silver after removing polymer and organic materials during the extraction process. In this study a simple wet process, of recycling the waste silver paste, using ammonia, was conducted. Silver ion extraction yield was increased using oxidant in the ammonia solution. Possible extraction yields, such as pH, concentration, temperature of ammonia, oxidant concentration and the extraction time. The particles that were obtained after the extraction process will be used as porous hydrophobic catalytic and applied to AI mask and hydrophobic ink. Keywords: Waste silver paste; Ammonia; Hydrophobic porous support

Jan 1, 2009

By John A. Wolfe

The concepts of sea floor spreading and plate tectonics provide more logical explanations of some geologic processes than were possible a few years ago. I plan to premise my discussion of the regional features of Philippine porphyry copper deposits on this tectonic basis, recognizing that parts of the picture can be explained in other ways, but in the belief that this is the best explanation of the whole. The sequence of events which results in the formation of Porphyry deposits (Figure 1) can be summarized as the result of collision of crustal plates, subduction of the oceanic plate, emplacement of a serpentine ultrabasic diapir, formation of a dioritic magma at depths of 300 to 500 km, rise of the magma to a sub crustal or intra-crustal chamber, eruption of andesitic volcanoes, emplacement of diorite or differentiation of the magma into more acidic products, multiple intrusion of hypabyssal rocks and hydro-

Jan 1, 1973

By Jean-Michel Rendu

In most mining operations, some degree of selectivity is applied. Whether one deals with surface or underground operation, ore zones, and waste zones are defined not only on the basis of the value of the ore contained, but also taking mining constraints into account. A number of computer techniques are presented which can be used to determine the optimum location of the footwall and hanging wall of ore zones intersected by drill holes. Minimum mining width and minimum internal waste width constraints are taken into account, as well as other economic constraints. The system is presented as an integral part of a larger manumatic ore reserve and mine planning system.

Jan 1, 1982

By C. D. Iles

The philosophy used in designing and writing Duval's Sierrita mine design programs is discussed. The Sierrita Incremental Design system (SID) is reviewed with emphasis on Pushback Extraction Design (PED). FED is a method by which predesigned pushbacks are sequenced into an optimized period-by-period design that can be directly utilized in daily operations as well as intermediate and long range planning. The advantage of SID is that it provides a practical, mineable open pit design. PED is not a theoretical design system; it is in operational use.

Jan 1, 1981

By William Lyman

GENERAL DESCRIPTION Shrinkage or shrinkage stoping refers to any mining method in which broken ore is temporarily retained in the stope to provide a working platform and/or to offer temporary support to the stope walls during active mining. Since ore "swells" when broken, it is necessary to shrink the muck pile a corresponding amount by draw¬ing some of the broken ore out as the stope is advanced-hence the name. Broken ore retained during stoping is drawn out after the stope has reached its limits. The stope may be left empty or may be filled with waste contemporaneous with, or subsequent to, the final draw. Traditionally the method implies conventional overhand stoping methods with miners working between the muck pile and the stope back, in a space which advances updip with mining and is maintained by balanc¬ing "swell" with "shrink." The shrinkage classification is also applicable to so-called "semishrinkage" methods in open pillar-supported stopes where broken ore is temporarily retained as a working platform but offers no wall support; and to various blasthole shrinkage methods which utilize broken ore temporarily retained in the stope for wall support, but which do not require miners to work from muck pile in the stope. The method is generally applied to steeply dipping veins of strong ore between strong walls. APPLICATION Geometry The geometry of a shrinkable vein is described in terms of dip, width, and regularity along dip. Overall strike and dip dimensions and irregularities along the strike generally impose no restrictions on the method. Dip is ideally 1.2 to 1.5 rad (70 to 90°). As dip falls below 1.2 rad (70°), the shrinkage draw begins to strongly favor the hanging wall side, thus leaving a poor working platform for conventional overhand work. This is particularly true in relatively wide stopes. The sup¬port afforded to the hanging wall also diminishes with decreasing dip, reaching nil as the dip approaches the repose angle of broken ore. Dips below 0.78 to 0.87 rad (45 to 50°) are not generally shrinkable except by open stope "seinishrinkage" methods. Minimum mining width is fixed by working space requirements in the stope-generally about 1 m. Shrink¬age in narrower veins requires that waste rock from one or both walls be broken with the ore and the attendant dilution accepted to achieve the minimum width. Nar¬row stopes are less suitable, encouraging hang-ups and bridging of broken ore, with the attendant problems of erratic draw and incomplete recovery of broken ore. Maximum practical width may be 3 m or less to over 30 m, depending upon the competency of the ore and its ability to stand unsupported across the stope back. This is a vital safety consideration in conventional over¬hand stopes, but is much less of a factor in blasthole shrinkage methods. Very wide veins and massive ore bodies have been mined by transverse vertical shrinkage panels separated by transverse vertical pillars which are either abandoned or recovered later by other methods. Regularity along the dip is a prerequisite of shrink¬age as there must be no serious obstruction to the flow of broken ore downward through the stope to the sill level. Gentle rolls along the dip are acceptable if the local footwall dip everywhere exceeds 0.78 to 0.87 rad (45 to 50°). Off-dip hanging wall and/or footwall splits can generally be mined selectively from a conventional shrink stope as they are encountered without ad¬versely affecting subsequent continuation of shrinkage mining updip on the main vein. Vertical offsets or major rolls along the dip which cannot be "smoothed over" generally require that a sublevel be established with new draw control development. Blasthole shrinkage methods are much less flexible (and thus less selective) in their ability to accommodate any of these irregularities. Ground Conditions The wall rock must be strong enough to stand with the minimal support afforded by the dynamic mass of broken ore in the stope. During active mining, local sloughing from the walls is restrained, but the broken ore affords little, if any, useful resistance to closure of the stope walls. Such squeezing, if present, may bind up the stope and cause the loss of much ore. Pillars left between and/or within stopes are effective in preventing closure but reduce overall recovery. Walls may be re¬inforced by bolting after each stope cut in conventional shrinkage but not in blasthole shrinkage. Ore in place must be strong enough to stand with no natural support across the stope width, although tem¬porary artificial support or reinforcement may be used locally in conventional stopes. Some spalling or sloughing is permissible in blasthole shrinkage as men are never present in the stope. Physical and/or mineralogical characteristics of the broken ore may impose restrictions on stope design and/or operational plan¬ning, and may even preclude the use of shrinkage al¬together. Examples include: ores which, when broken, are cohesive or which tend to pack or cement together under the influence of ground water, wall pressure, and/ or chemical reaction. Such conditions precipitate er¬ratic draw during mining and often result in difficult and/or incomplete final draw; pyritic ores which oxidize very rapidly in the stopes and may generate heat, imposing a fire hazard by spontaneous combustion; sulfide ores which oxidize sufficiently in the stopes to adversely affect mill recovery by flotation; and ores (es¬pecially those containing uranium minerals) which ex¬ude radon gas and thereby impose ventilation constraints on stope design. In most cases these problems can be minimized by limiting the size of stopes, by minimizing the duration of mining activity in each stope, and by promptly drawing each stope empty following comple¬tion of mining.

Jan 1, 1982

By Richard L. Bullock

OPEN STOPING An open stope is an underground cavity from which the initial ore has been mined. Caving of the opening is prevented (at least temporarily) by support from the unmined ore or waste left in the stope, in the form of pillars, and the stope walls (also called ribs or abutments). In addition to this primary support system of open stoping, some secondary support may also be required using rockbolts, reinforcing rods, split pipes, or shotcrete to stabilize the rock surface immediately adjacent to the opening. The secondary reinforcement procedure does not preclude the method classified as open stoping. There are many forms of open-stope mining used to extract the initial material from a mine. Having once established that the mineral and waste rock are competent enough to use an open-stoping method, and assuming that the reserve is not classified as gassy, the Form which the method will take is primarily determined by the dip and thickness of the reserve. How these two factors affect the selection of the open-stope mining is discussed in a later chapter. At this point it will suffice to say that the classification of the open-stopes mining system which follows is based on whether dry' broken materials flows by gravity or whether it must be moved by nongravity methods where energy must be supplied to move the material. Room-and Pillar-Mining Room-and-pillar mining is an open-stoping method where mining progresses in a nearly horizontal or low angle direction by opening multiple stopes or rooms, leaving solid material to act as pillars to support the vertical load. Since the direction of excavation (angle of dip) is below that which would cause the dry material to flow by gravity to a drawpoint or gathering point, the material must be loaded in the room where it was extracted and transported to a point where it will flow, either by gravity or mechanical means, to a central gathering point to be taken out of the mine. This is an important aspect of room-and-pillar mining which differentiates the system from other open-stope mining methods which rely heavily upon gravity to transport ore from where it was broken to a lower elevation, usually through a drawpoint. There are many variations of the method which go by a number of names in local districts: breast stoping, breast-and-bench stoping, board-and-pillar, stall-and-pillar, and panel-and-pillar are all basically open-stope room-and-pillar mining. In some instances detailed stope planning is almost nonexistent; i.e., the operator simply follows the visual pay values, leaves pillars only where necessary, and tries to locate them in the zones of lower value. This method of mining is as old as the beginning of underground mining itself, dating back thousands of years. Early in the history of mining in this country, the term "gophering" was used to describe this method (Peek 1941). The term is appropriate, for it brings to mind the exact results of this type of system-a random and irregular room-and-pillar mine. In other instances where the mineral values are consistent both in physical dimensions and quality, the mine layout can be planned to the last detail, resulting in a uniform room-and-pillar mine. Coal, trona, gilsonite, potash, oil shale, salt, limestone, and sandstone mines can usually follow such a system. Today, most metal mines using a room-and-pillar operation try to mine as regular a pattern as possible but deviation in height, width, thickness, dip, and grade of the ore results in comparable deviation in the mine plan. Variations of the Room-and-pillar System It is necessary to briefly describe some of the many variations of the room-and-pillar system of mining, enabling the reader to fully explore the concepts and become familiar with the terminology used before going on to the details of mine design. Full-Face Slicing: If in the process of opening the rooms the total vertical extent of the mineral values of the particular seam or strata are extracted from the advance of one vertical face, the term used to describe this is full-face slicing. This face is also known as the "breast." There is no mineral of economic value intentionally left either in the floor or the roof (back) to be mined later. To be able to extract the full-face height in one pass, the mining equipment must obviously be designed to reach as high as the back. In an Appalachian coal mine, this may be all of 660.4 mm (26 in.); for a future oil shale property it might be 15.24 m (50 ft). Normally, however, in a majority of mines where the mining face gets over 6.09 to 6.7 m (20 to 22 ft), the tendency is to divide the face into more than one pass. Over this height, it becomes difficult to properly see and remove loose rock from the back with a hand "mining bar." Where the process of taking down loose rock has become mechanized, higher full-face mining can be safely practiced. Most eastern and midwestern coal seams and western uranium, trona, and potash seams in the United States are easily reached in a single face; many limestone, lead, and zinc mines must resort, at least in part, to "multiple-slicing" to remove all the minerals of value. Multiple Slicing (also known as multiple-pass mining): In many cases it is not practical to carry the full vertical height of the mining horizon as a full face. The face is divided into parts known as the breast, bench, and/or brow. Ideally, if the operator knows the vertical extent of the mineralized zone, he will drill and blast the first pass at the top of the zone, thereby

Jan 1, 1982

By W. M. Ma, Daniel W. H. Su, K. Centofanti, Yi Luo, W. L. Zhong, Syd S. Peng

2.1 INTRODUCTION When total extraction of an opening of sufficient size is reached in a horizontal coal seam, the roof strata in the overburden deform continuously to reach a new equilibrium condition. The severity of deformation decreases upward toward the surface. As the downward saggings of the strata propagate and reach the surface, there will be a depression zone on the surface directly above, but extending beyond the edges of the underground opening. This is the surface subsidence basin or surface subsidence trough. The surface subsidence basin is circular in plan view, if the coal seam is horizontal and the mined-out opening is square in shape. But it is rectangular with rounded corners or elliptical if the coal seam is horizontal and the mined-out opening is a long- and thin rectangle or a short-rectangular, respectively (Fig. 2.1). Most underground openings (e.g., longwall panel) assume rectangular shape when total extraction has been completed. Theoretically the edges of the subsidence basin are the points of zero subsidence. But it is difficult to exactly locate the points of zero subsidence. Therefore in practice the points with vertical subsidence of 0.4 in. (10 mm) are used. The final subsidence basin is that which exists long after the mining has been completed, because its magnitude and shape are quite different from the dynamic subsidence basin formed while the face is moving. 2.2 CHARACTERISTICS AND TYPES OF DEFORMATION IN THE FINAL SUBSIDENCE BASIN For a horizontal coal seam, every point in the subsidence basin moves toward the center of the basin. Subsidence is maximum at the center of the basin. Any cross-section that passes through the point of maximum subsidence and either parallel to AB or CD line (Fig. 2.1) is a major cross-section along which principal directions of surface movements occur. However among those infinite numbers of major cross-sections, two specific ones are of special significance, not only because the magnitudes of surface movements are the largest, but also because they are the most easily identifiable directions, i.e., one that is parallel to the faceline at the center of the basin (CD in Fig. 2.1) and' the other is that perpendicular to the faceline but parallel to the diction of face advance (AB in Fig. 2.1). Nearly all the subsidence data obtained in the US have been derived from these two cross-sections, although some cross- sections parallel to CD but near the edges of the panel have also been included. In addition to moving horizontally toward the center of the basin, every point in the basin also subsides vertically. The magnitude of subsidence increases toward the center of the basin. Therefore surface subsidence is a three-dimensional problem and should be treated so in all cases. On all the major cross-sections, only principal subsidence and principal displacement occur. Since subsidence and displacement vary continuously in every major cross-section, three additional deformation components are de- rived, i.e., slope, curvature, and strain. On all other non-major cross-sections on the other hand the five components are accompanied by two additional components, i.e., twisting and shear strain. The seven components of the surface movement are defined as follows (Fig. 2.2): 1. Subsidence, S. On any cross-section, the vertical component of the surface movement vector is called surface subsidence. It generally points downward. But sometimes it points upward in areas ahead of the faceline or beyond the edges of the opening. In such cases it is a surface heave which is usually less than 6 in. 2. Displacement, U. On any cross-section, the horizontal component of the surface movement vector is called surface horizontal displacement. It generally points toward the center of the subsidence basin. But in steep terrain, it moves along the downdip direction 3. Slope, i. On any cross-section, the difference in surface subsidence between the two end points of a line section divided by the horizontal distance between the two points is called the surface slope of the section. 4. Curvature, K. On any cross-section, the difference in surface slope between two adjacent line sections divided by the average length of the two line sections is called the surface curvature of those two line sections. There are two types of curvature: con- vex or positive curvature and concave or negative curvature. 5. Horizontal strain, e. On any cross-section, the difference in horizontal displacement between any two points divided by the distance between the two points is called horizontal strain. If the distance between the two points is lengthening, it is tensile strain with positive sign. Conversely, if it is shortening, it is compressive strain with negative sign 6. Twisting, T. On the surface of the subsidence basin, the difference in slope between two parallel line sections divided by the distance between the two line sections is called twisting. 7. Shear strain, y. Shear strain is the changes in internal angles of a square on the surface of the subsidence basin or on any major cross-section. It is the summation of the differences in incremental (or decremental) lengths between the two opposite sides divided by the original distance between the two opposite sides. More precisely, the surface deformation indices (i.e., slope, strain, curvature, twisting and shear) are defined by derivatives of surface movement components. For simplicity, the x- and y-axes of the cartesian coordinate system are set to be parallel and perpendicular to the cross-section of interest, respectively. In such a coordinate system, slope and curvature along x direction are the first and the second derivatives of the vertical components (S) of surface movement with respect to x, respectively, or i, = ds/dx and kx = d2s/dx2. Horizontal strain along x direction is the first derivative of the component along x direction of the horizontal displacement,

Jan 1, 1992

By W. M. Ma, Daniel W. H. Su, K. Centofanti, Yi Luo, W. L. Zhong, Syd S. Peng

6.1 INTRODUCTION A surface structure will suffer damage when the additional stresses induced by ground deformations associated with surface subsidence, plus the original stress introduced by construction de¬sign, exceed the strength of the structural elements. In this con¬text, there are two methods available for preventing and control¬ling surface structural damage: one is to strengthen the structure and the other is to design the mining operations such that ground deformations at the structure site can be reduced to an acceptable level. Mining operations include panel layout and mining tech¬niques. These methods are detailed in this chapter. It must be noted that most prevention/control methods men¬tioned in this chapter are used in the countries where the reference papers are cited. In the United States, the coal operators are not required to take those measures mentioned in this chapter. Some of the methods described in this chapter cannot be implemented with¬out changes in the current mining practice as permitted by laws. In addition cost of implementing those methods are not considered here. 6.2 PANEL LAYOUT As shown in Figs. 2.9, 2.10, and 2.11, permanent ground deformations in a subsidence basin mainly concentrate near the edges of the underground opening, and can be divided into four zones. A structure located in different zones will be subjected to different types and magnitudes of ground deformations. In laying out the panels, Table 5.1 and Figs. 2.9, 2.10, and 2.11 could be taken into consideration. Attempts could be made to avoid placing the structure on a location where the ground deformation to which that structure is sensitive is at its maximum. Therefore rational design of the panel is the simplest way to reduce structural defor¬mations. Panel design involves the determination of panel dimension, panel edge location, direction of face advance, and use of yield chain pillars. A. Panel Dimension Since longwalls in the US employ a multiple-entry system, where rows of chain pillars are left unmined, subsidence over those chain pillars is usually smaller. Therefore, whenever possi¬ble, the panel dimension could be designed such that a major structure or structures are over those unmined chain pillars, be¬tween adjacent panels, or some distance beyond both ends of the panels. At the center of the supercritical final subsidence basin, a structure will not be subjected to any final or permanent ground deformations. In order to create such a condition, the panel width must be such that the structure will be located beyond the major influence zone of the final subsidence basin, the minimum dimen¬sion of which must be: [ ] where L is the width or length of the final mined out gob, t is the width or length of the structure to be protected, h is mining depth and [ ] s is the angle of full subsidence. B. Panel Edge Location Wherever there is a permanent panel edge, there are large ground deformations induced on the surface on both sides of the permanent panel edge. Therefore whenever possible the panel di¬mension should be designed such that the permanent panel edges could be located in the areas with the least impacts. In terms of permanent edge location, it is best to eliminate any permanent panel edge under a structure or groups of structures. If this cannot be done, the panel should be lengthened to reduce the number of permanent panel edges, or narrower multiple panels advancing in the same direction in a staggered manner could be employed. If the structures are located in Zones II and III, the longer dimension of the structure must be parallel to the nearest perma¬nent edge (Fig. 6.1). But in Zone IV, the longer dimension should be tangential to the corner of the permanent panel edge. If the structure is inclined to the permanent panel edge, it will be sub¬jected to twisting and shearing. C. Direction of Face Advance The direction of face advance should be parallel to the long axis of the structure. But if the structure is to be located at or close to the center of the final subsidence basin, the direction of face advance should be perpendicular to the long axis of the structure. Careful choice of the direction of multiple face advance is the most effective way to reduce structural deformation and thus dam¬age. This applies the principle of overlapping and cancellations of ground deformations, due to multiple face advance, at the right time and at the right intensity, e.g., opposing tilts, concave and convex curvatures, tensile and compressive strains are induced simultaneously on the structure to be protected by two or more faces. D. Use of Yield Chain Pillars In US longwall panels there are generally two or three rows of stiff chain pillars between the panels. The combined width of the chain pillars ranges from 100 to 350 ft(30 to 107m). depending on mining depth. In general, surface movement above the chain pil¬lars after the panels on both sides have been extracted is much smaller, as compared to that in panel center. Thus in order to create critical or supercritical width of opening and eliminate sur¬face bumps over the chain pillars, yield chain pillars may be em¬ployed (Jarosz and Karmis, 1986). However if yield pillars are to be used, it must be designed such that it yields totally right after the panels on both sides have been extracted. Unfortunately cur¬rent yield pillar design techniques cannot predict when and how much it will yield. In summary, whenever possible attempts could be made to lay out the panel in such a way that surface structures are located above chain pillars between panels or above solid coal beyond both ends of the panels. In those areas the surface structures will most likely be unaffected, or if affected, the damage is so minor that no remedial measures are necessary. 6.3 CONTROLLED MINING TECHNIQUES Several mining techniques are available for reducing the sur¬face ground deformations of specific types. Regardless of tech-

Jan 1, 1992