Search Documents

By W. Ellison

Worldwide development of commercial markets for FGD (flue gas desulfurization) gypsum is described and used as a basis for assessing potential overall market growth and regional demand foreseen in the U.S. during the 1990s. Diverse strategies are outlined for cost-effective substitution of this major supply from acid rain control retrofits (power plant scrubbers) for natural gypsum in the principal, existing markets: gypsum board and portland cement. Another focus of utilization forecasting is a key group of related. new-product advancements including floor screeds, mining mortars and various types of innovative construction products.

Jan 1, 1993

By George E. Valadão, Iván A. Reyes, Mizraim U. Flores, Armando C. Araujo, Rubén H. Olcay

Dewatering tailings to higher grades than paste produces a stable deposit that typically does not require retention dams and is called a “dry stack.” A proposal of different dewatering techniques applied in the fine tailings produced after final desliming phase, obtained from the treating of phosphatic ores, is the main objective of this work. The dewatering techniques evaluated were column thickener, deep cone classifier, and hyperbaric filtration. Calcite and dolomite were the main mineral contained in the phosphate tailings and these have a very fine granulometry; the tailings presented different behaviours related to the dewatering technique applied. The test column thickener and deep cone classifier with the best operational parameters found to obtain a maximum percentage of solids in mass were ~ 71% and ~ 67%, with values of yield stress ~ 200 Pa and ~ 100 Pa, respectively. In the hyperbaric filtration, a cake with ~ 10% moisture was obtained. This indicates that the transportation conditions are not the same. The overflow turbidity levels obtained from column thickener and deep cone classifier test did not exceed the value 100 NTU, whilst for the filtrate of the hyperbaric filter obtained values ~ 800 NTU. It was possible to preliminary estimate the recovery direct of water, considering each dewatering technique for final disposal of the tailings. The best dewatering techniques obtained were in the following order for the disposal in phosphate fine tailings dams; the hyperbaric filter showed an excellent dewatering capacity with productions rates around 160 kg h− 1 m− 2 for moisture cake of 10%, followed by the column thickener and deep cone classifier with paste ~ 71% of solids (W/W) and high-density slurry ~ 67% of solids (W/W), respectively.

Dec 23, 2023

By Jamal Rostami, Mark Board, Clayr Alexander, Muthu Vinayak Thyagarajan

In the past several decades, many major equipment manufacturers have ventured into developing new technology for underground hard rock excavation. This includes variety of configurations for full and partial face mobile excavation units. Mining industry prefers machines that can excavate noncircular, flat invert profiles and be able to make tight turns in hard rock. The need to use disc cutters for cutting hard rock has impeded the development of such machines due to the need for gripper system or large mass of a machine to support the force requirements of the disc cutters. Most of the prior attempts have been partially successful and the operations have faced some practical limits and challenges. Among the units that have been successfully used, one can name mobile miner, which was used for rock excavation in some projects. A redesigned mobile miner, called the “Remote Vein Miner,” or RVM, has been developed by Epiroc for underground hard rock mining in Hecla’s Lucky Friday Mine. This equipment potentially opens numerous opportunities for innovation in civil tunneling projects, where the operational flexibility and accessibility of a TBM’s limited tunnel path, design of the profile, and cost are limiting factors. This paper explores the application of the RVM in tunneling projects, its advantages and possible areas of innovation in tunnel planning and design.

Jun 13, 2021

By CORA ROELOFS

In the USA, miners are at higher risk for work-related disorders that could precipitate an opioid prescription, injury-related opioid prescriptions, and opioid overdose. We aimed to support prevention of these outcomes with an “opioid hazard awareness” miner safety training module. In January and February 2020, the training module was embedded within required mining safety and health training for stone, sand, and gravel miners in Massachusetts (USA). Training impact and reception were assessed with a pre- and post-training survey of trainee characteristics, training content knowledge, and attitudes. Over 800 miners were trained and over 600 responded to surveys. We found statistically significant improvements in opioid risk factor knowledge and knowledge of resources to help a coworker. Nonstigmatizing attitudes were high both at baseline and following the training. The training was perceived as relevant and useful by trainees. Improving opioid hazard awareness in high-risk worker populations has potential to reduce opioid dependence and downstream impacts including overdose death. Employer injury-prevention efforts should be reinforced while worker health and safety training enhances awareness of opioid-related harms and prevention strategies for miners and other high-risk worker populations.

Nov 19, 2021

By B. Kyslinger

"In underground mining, machine design is predominantly dictated by mine conditions and individual customer desires. In partnership with Foresight Energy, J. H. Fletcher & Company was tasked to design and manufacture a new roof bolting machine with six independent drilling apparatus on board capable of drilling and bolting the roof and ribs with material handling. This is the first Fletcher® six head machine to be designed and built for the mines in the United States. The machine is intended to work in the Illinois Coal Basin. The objective was to produce a machine capable of drilling and installing six bolts simultaneously with a limited number of operators. The goal of the mine is to decrease the time to bolt a cut to improve the safety level of the current roof bolting method, improve efficiency and to improve the bottom line cost of entry development. The customer wanted four mast feed drills at the front of the machine dedicated to installing roof bolts and then another two mast feed drills behind them dedicated to rib bolts. This dictated the requirement of latched controls, which would allow the operator to start drilling one hole and then latch the controls to be able to move on to the next. To accomplish this, we developed a unique hydraulic latch circuit to maintain operator safety and compliance. Guarding was added to prevent an operator from coming into accidental contact with a latched drill. The result of the design is a machine with a single platform and six independent masts with drillheads: four masts strictly for drilling and installing roof bolts on the front of the platform and then two masts on the back of the platform for rib bolts. The feed and rotation controls at each operator’s station include a latch control for drilling. The latch control will allow the operator to lock in the feed and rotation once the hole has been collared, allowing the operator to move on to the next hole. The rear of the machine is equipped with material handling. There are two material pods with winch controls as well as a mesh rack that includes mesh lift, mesh tilt and mesh sump. The six-head roof bolter allows fewer operators to drill and install roof and rib bolts, which in turn lowers the miners’ roof exposure per cut. This design reduces the operator’s exposure from the inherent pinch points and rotary hazards once he has engaged the latch drilling. Therefore the machine will help to decrease the time to bolt a cut, improving productivity while enhancing the ability to operate the machine safely. INTRODUCTION When mining underground it is necessary to support the roof quickly to prevent it from collapsing after an area has been mined. Since the 1950s, the primary method for supporting the roof has been the installation of roof bolts. Roof bolting is one of the most basic functions yet one of the dangerous jobs in the underground mining operation (1). The Mine Safety and Health Administration’s (MSHA) Health and Safety Accident Classification injury database showed an average of 660 roof bolter operator accidents per year over a 5-year period (1999-2003) (2). The numbers show that roof bolting is the most hazardous machine-related job in underground mining. It represents 39 percent of all machine-related accidents in underground coal mines. In 1993, the U.S. Bureau of Mines conducted a study that has shown the activity of drilling as the most hazardous job task performed by a roof bolter operator, accounting for 31 percent of all roof bolting injuries (3). Almost half (46%) of these drilling injuries were due to falling rocks or coal from the roof. All of these injuries occurred under supported roof. The majority of these injuries (about 99%) are not caused by a major roof collapse but from falls of smaller rock from the immediate roof. This type of roof failure has also been termed “skin fall.”"

Jan 1, 2017

By Rick L. Williamson

International lending institutions have charters requiring projects that are seeking loans to adhere to certain environmental performance standards, including compliance with host-country environmental laws, as well as observance of international environmental policies and guidelines. The most commonly applied international environmental policies and guidelines are those established by The World Bank. Lenders require a review by an independent engineer to determine that the feasibility study plans have been developed in accordance with the applicable environmental commitments. Lender agreements require independent engineer evaluation of environmental performance through the construction phase and initial operations phase of the project, culminating in the issuance of an "Environ- mental Completion Certificate."

Jan 1, 2001

By T. Rockley, J. Brune

"The mining of tabular deposits accounts for a significant portion of modern production in both underground hard rock and especially, soft rock mining. There is a large discrepancy between the availability of tabular reserves and the amount of development of these deposits, particularly when the deposit has a dip of around 25-50 degrees. This project studied the technical and practical barriers to the mining of these deposits through modern and historical case studies. The primary technical barriers to the development of these deposits are material movement and roof support. The study of historical attempts overcome these barriers and why they failed allowed us to research the possibility of implementing modern technology on previously unsuccessful methods. By modifying some common mining methods, some of these deposits can be mined at only a marginal increase in cost and using readily available equipment. These modified mining methods could make previously underdeveloped deposits to become viable. INTRODUCTION Tabular deposits are defined as orebodies that extend at least hundreds of meters along two dimensions, and a substantially smaller amount along another [1]. Moderately bedded tabular deposits are mined less often than their more horizontal counterparts due to the technical issues they present. These issues often cause lower productivity, higher cost, and more frequent accidents. Moderate dip is a less well defined term; but in this case, it will refer to any deposit which has a dip of at least 20°. This paper will focus on deposits that dip around 25°-50° and are deep enough to require underground excavation methods. These deposits are too steep for most conventional methods yet not steep enough for gravity fed methods to work efficiently. In some cases, this dip range is also referred to as intermediate or steeply dipping. The types of deposits most likely to fall into this category are sedimentary bedded deposits such as coal, trona, evaporates, placers, and other alluvial deposits. Some other types of deposits can fall into this category as well. These include some of the metal reefs such as the Bushveld Complex in South Africa, which was deposited by lava flows, but is tabular. Some areas have dips that fall into the moderately inclined category. There are also some metamorphic deposits such as slate or marble that can have dips of more than 20°. The dip angle of these deposits can cause several challenges. Ore movement becomes more difficult as the exceeds the limits of conventional conveyors, rubber-tired, or tracked vehicles. At the same time the dip is below the angle of repose of the material. This prevents gravity assisted haulage, as the ore and waste will not run downhill by itself. Another common problem in moderately inclined underground mines is roof support. The dip angle can increase the risk of pillar and support failure. This is due to slippage between rock layers, non-perpendicular support of the vertical stresses, and slippage of standing supports. The inclination leads to stresses that are not usually found in typical horizontally bedded deposits. These stresses may require larger pillars that may reduce ore recovery below profitable levels."

Jan 1, 2017

By D. Scott Scovira, Thomas Gustavsson

Exiting WW2, the potential of nitrates and hydrogen peroxide for application as industrial explosives both became known. The technology stream advanced the development and uptake of nitrate-based explosives to the point that they are the current global standard for blasting. Recently environmental issues are influencing the strategic agenda of extractive industries. The mid-2010s saw renewed interest in hydrogen peroxide explosives to eliminate NOx fume. Carbon reduction initiatives in the 2020s provided additional impetus to investigate hydrogen peroxide-based explosives. Hypex Bio is at the forefront of developing and delivering bulk gas sensitized Hydrogen Peroxide Emulsion (HPE) for blasting. HPE consists of hydrogen peroxide along with smaller amounts of fuel and emulsifier. The consistency of HPE is similar to industry- standard nitrate-based emulsions. It is compatible with existing priming and initiation systems. HPE does not contain nitrates and thereby does not produce post blast nitrous oxide fumes nor discharge of nitrates or ammonia to mine water. Importantly, HPE contributes to reduction in total carbon emissions as compared to nitrate-based explosives.

Feb 1, 2025

By Kevin B. Doyle

Virtually all industries use sulphur in some form. About half of the world's production is used in the production of fertilizers. Sulphur is produced in one form or another in over sixty countries in the world. The major producing countries, in order of importance, are: U.S.A., Canada, U.S.S.R., Poland, Japan, France, Mexico, and Spain. Canada is the largest exporter of sulphur presently supplying about 30% of the world elemental sulphur export trade. It has held this position since 1968. World sulphur resources are virtually unlimited. Future world competition will come from Iraq and other Middle East countries as well as Central and South America.

Jan 1, 1978

By G. Vogt

Water is one of the most important ressources of our planet. Unlike many other natural resources, water cannot be substituted by anything and must therefore be handled with the utmost care. Depending on the region and the possible shortage of water, the importance of water increases even further. Water consumption is not the only factor. In the construction industry, water pollution from auxiliary and operating materials and processes as well as other contaminants and their resulting load on wastewater play an important role. The sources for wastewater on tunneling construction sites are various: Washing water, seepage water accumulating in construction pits, tunnel water, water used in the slurry circuit in fluid-assisted tunneling methods or water from concrete work and stone cutting all these waters are contaminated with a range of pollutants like solids, hydrocarbons, heavy metals, etc. These contaminants can be removed or treated/reduced with the help of specifically designed wastewater treatment plants (WTPs). After the treatment the cleaned water can be either, in best case, reused on the construction site itself or discharged into water utilities like the available sewer or river pin respecting their discharge requirements. Due to dwindling water resources globally, the continuously rising discharge limits and the ever more important aspect of sustainability the use of WTPs on tunneling construction site will be indispensable. In this paper, it will be presented how these systems are designed and work, what advantages they offer environmentally as well as financially and what to look out for when planning and implementing such a system onto jobsite.

Jun 23, 2024

By Mike Wongkaew, Brandon Kluzniak, Per Vilhelmsson

Rail access to Ontario International Airport (ONT) has long been a goal of San Bernardino County Transportation Authority (SBCTA) to increase public transit options to ONT and provide incoming ONT passengers improved access to San Bernardino County and the greater Southern California region. This paper describes the planning for the Design-Build-Operate-Maintain (DBOM) delivery of an emerging technology tunnel connection between the Rancho Cucamonga Metrolink station and ONT. The paper discusses key technical considerations, challenges, and opportunities; conceptual configuration development; and construction planning and establishment of the footprint for the underground connection.

Dec 1, 2022

By L. R. McCullough

To compete in Today's Market, Mine Managers have two, often conflicting tasks. They are to improve productivity, allowing the mines to compete in our world markets and to improve the environment in which our miners must work. To Maintain and improve the environment to ever increasing acceptable levels requires monitoring. In years passed this required considerable labor, which was provided by the Ventilation Department. They continuously took manual samples using hand-held instruments, sampling gas level such as CO for fire and methane for explosive risks. In addition they took continuous air velocity readings with hand-held instruments which allow them to calculate the ventilation air movement in each area of the Mine. This manual gathering of information was not only expensive and slow but marginal at best. It was marginal because the gas sampling was sporadic rather than continuous, as sample reading taken in one part of the mine would likely not be repeated for another 8 hours. If problems did occur, they likely went unobserved until they reached crisis proportion.

Jan 1, 1990

The primary use of coal in the US is for electric generation. The problems associated with the use of this vast amount of coal is the central theme of these sessions. The problems discussed include: production capacity, mining problems, coal cleaning, transportation, combustion, and various environmental problems, such as health effects of coal combustion, water and air pollution, and solid waste disposal.

Jan 1, 1979

By John Murray, Daniel Ebin, Robert Gould

The Atlanta Plane Train project at Hartsfield-Jackson Atlanta International Airport employed the progressive design-build approach. This provided opportunities for collaboration between the design-builder, design engineer, and owner and the implementation of innovative design and construction approaches. The innovations have reduced risks, allowed for adjustments during design to accommodate new challenges, and provided open-book cost and schedule evaluations. The progressive design-build approach has also allowed for pricing of work to occur in phases—capturing the design/construction challenges as the project evolves and when they are more clearly defined. While this has allowed for pricing to be performed with better project understanding and therefore less contingency, the associated time frame for approvals has required careful consideration to avoid impacts to the schedule. This paper discusses the benefits and challenges of the progressive design-build approach.

Dec 1, 2022

By Jacob Grasmick, Bill Newns

Despite ongoing digitization and “hardware” technological advances, geotechnical uncertainty remains the most significant risk in underground and tunnel construction. And, whilst they are commonly held up as an example of the sophistication of the industry, the practice of drafting and using geotechnical baseline reports is subject to a wide range of influences, not all of which support good risk management. Uncertainties in predicting ground behavior, the gap between the pre-construction assumptions, and the systemic response to construction remains a significant technical and communication challenge. Accordingly, this paper presents a framework to quantify geotechnical uncertainty using geostatistics and translate these into practical tools for ground risk management throughout planning, procurement and construction. Adopting even some of the principles of this framework should provide improvements to contract risk management and should assist to minimize the potential for commercial losses.

Dec 1, 2022

By A. N. Pritchard

The development of vibrating screens over the last century has seen many variations to suit the exacting requirements of industry. Indeed, as each year passes, industry has presented the challenge to screen manufacturers of supplying larger machines than those used in the past and the question is often posed - what is the maximum limit? Not only must size or screen area be considered but excellence of performance in terms of screening efficiency must be maintained or maximized.

Jan 1, 1983

By Jonathan K. Hrica, CASSANDRA L. HOEBBEL, Jennica L. Bellanca

Accidents involving powered haulage and mobile equipment like haul trucks are a major safety concern in the U.S. mining industry. They account for more than 50 percent of surface mine fatalities each year [1]. A recent National Institute for Occupational Safety and Health (NIOSH) analysis of 91 fatal incidents identified loss of vehicle control and situational awareness as key contributors [2]. However, the first-hand perspectives of operators are often missing, emphasizing the need for deeper insights into operators’ decisionmaking, lessons learned, sensory cues and mental strategies used during near-miss events. The findings in this analysis will help inform the development of training and safety solutions to prevent or reduce haul truck accidents.

May 1, 2025

By A. Halim, J. Gustafsson, A. van Wageningen, J. Johansson, · J. Lööw, K. Kocsis

A major part of the European Union’s (EU) project Sustainable Intelligent Mining System (SIMS) is investigating the development of diesel-free/carbon–neutral underground mines in order to ensure sustainable underground mining in the future. Replacing diesel machines with electric vehicles in underground hard rock mines has been widely acknowledged by the mining industry worldwide as a critical step to improve working conditions by reducing diesel exhaust–related contaminants, to reduce mine ventilation electrical power cost by reducing mine airflow quantity, and to reduce mine greenhouse gas emissions. All of these are major requirements to achieve sustainable future underground mining practices. A field trial of Epiroc’s 2nd generation of Battery Electric Vehicles (BEVs) at Agnico Eagle Finland’s Kittilä mine was conducted during 2019–2020. Vehicles tested were MT42 mine truck, ST14 Load-Haul-Dump (LHD), and Boomer E2 jumbo drill rig. This paper outlines the improvement of the working conditions observed in the field trial, and the opinions of the mine personnel at Kittilä mine on using BEVs instead of diesel machines. Measurements of atmospheric contaminants and air temperatures taken during the field trial clearly demonstrated a significant improvement of working conditions when BEVs were operating as opposed to diesel machines. This field observation was supported by the opinion of the majority of the Kittilä mine workers. However, some remaining concerns must be addressed before BEVs can replace diesel machines.

Oct 25, 2021

By Andrew L. Mular

Methodology to model, simulate and optimize full scale mineral pro- cessing circuits in production environments is reviewed and evaluated. Strategies for data acquisition and adjustment are considered along with techniques to fit models to adjusted data. Examples are considered for clarity.

Jan 1, 1989

By Rodolfo V. de la Cruz

The stresses in the materials surrounding an underground opening are dependent upon the virgin stress field, the geometry of the opening and changes in boundary conditions as mining progresses. For most underground openings especially in coal mines, roof bolts are installed to help stabilize the opening. While most parameters in roof bolt design and installation have been thoroughly investigated, the effects of the initial stress field on the effectiveness of roof bolts have not been recognized. This paper summarizes the results of investigation of the effect of the initial stress field on the performance of mine roof bolts. Roof bolt installations are duplicated in the laboratory utilizing conventional roof bolt frame, commercial roof bolts and shells, mine torque wrench and encapsulated rock specimens for anchorage. A special and primary feature of the laboratory set-up is the addition of a loading system for generating stresses at the anchorage specimens. For this preliminary study, different levels of hydrostatic stress fields were induced at the anchorage specimen, instrumented roof bolts were installed in the usual manner, and the bolt load loss-with-time observed. Statistical analysis of data showed that the stress field at the anchorage horizon has a considerable influence on the performance of mine roof bolts, i.e. the higher the stress field, the higher the anchorage efficiency. From this observation, methods of improving the performance of mine roof bolts utilizing new shell designs and methods of installing them are suggested.

Jan 1, 1978