Search Documents

By Lancelot E. Kun

The high-rate floc blanket clarification process developed by the Anglo American Corporation of South Africa is capable of continuously clarifying gold and uranium pregnant solutions containing 200-2500 mg/L suspended solids to below 25 mg/L solids at an average rising velocity of 8 m/h at the low process cost of R0,001-0,002 per ton of liquid treated. Overall process cost savings are mainly due to increased polishing filtration cycle times.

Jan 1, 1984

By Denise Crocce Romano Espinosa, JUNIOR AMILTON BARBOSA BOTELHO, Jorge Alberto Soares Tenorio

Bauxite ore is used to produce alumina in the Bayer process. For each tonne of alumina produced, around 1 to 1.5 t of bauxite residue is generated, with an estimated 4 Mt of the residue generated worldwide in 2015, four times more in 1985. The residue is currently stocked in tailings dams. A new step in the Bayer process has been used to recover sodium hydroxide, which is used as a leaching agent, and reduce its content in the residue. After digestion, the residue is separated from the Bayer liquor and passed through press filters. This bauxite residue is known as a source of scandium. Characterization of the residue is an important step to map opportunities worldwide. For this reason, the goal of the present study was to characterize the bauxite residue and evaluate the challenges for scandium recovery. The scandium content was found to be 43 g/t, which makes this bauxite residue attractive for extraction purposes.

A methodology has been developed and demonstrated to be effective in reclaiming surface-mined land for a forestry post-mining land use. The forestry reclamation approach (FRA) has been applied, almost exclusively, to flat or gently rolling surfaces. One of the primary steps in the FRA is to loosely grade the top 1.22 m (4 ft) of soil or substitute root growth medium to avoid excessive compaction. Concern has been expressed by regulators and the public that loose grading on steep slopes (i.e., greater than 23°) could lead to slope failures, which is one of the issues that the Surface Mining Control and Reclamation Act of 1977 (SMCRA) sought to correct. A field investigation was conducted at a steep-slope contour operation in eastern Kentucky to test the applicability of FRA in this setting. Final grading was performed according to FRA standards. The surface consisted of two distinct substitute rooting media. One was unweathered gray sandstone and the other was a combination of gray sandstone, brown sandstone, and topsoil. A variety of native hardwoods was planted following the FRA guidelines. The slope was instrumented with 70 survey monuments to monitor for mass movement. The reclaimed spoil was also characterized using bulk density and penetrometer resistance methods. The characteristics of both spoils are similar to those observed on flat to rolling surfaces where the FRA has been used and, after one year, approximately 70% of the trees had survived. During this first phase of investigation, there has been no major mass movement of the slope and slope stability analysis indicates that the application of the FRA has little impact on the overall stability of the slope. Mining Engineering, 2011, Vol. 63, No. 12, pp. 55-62. Official publication of the Society for Mining, Metallurgy and Exploration, Inc.

Jan 1, 2011

By Paul T. Allsman

The guiding principle in developing this plan resulted from evaluating potential future markets for oil, the quantity of mineable oil shale and the optimum rate of production comensurate with market demand on the available oil from shale. In addition, the rate of production may depend upon a solution to the problems of scarcity of resources other than oil shale. The rate of production finally will tend to establish the choice of technologies with these limits. The principle components discussed will be: 1) The place of oil shale among the various energy sources and its relative adaptability for use in the area of major consumptive demand. 2) A recalculation of the reserves and their classification on the basis of quantity, grade - gallons per ton, - and physical characteristics principally thickness, overburden and depth.

Jan 1, 1982

By K. Ueda

Lead concentrates from Kuroko (black ore) mines, which contain Cu 4 ? 7%, Pb 55%, Zn 3 - 7%, As 0.5 - 0.9% are treated by hydrometallurgical process in order to smelt the product by electric furnace smelting together with other lead resouces from Kuroko. The hydrometallurgical pretreatment involves sulfuric acid leaching at first stage, ferric leaching at second stage. This paper describes the short history of lead recovery from Kuroko and the performance of laboratory test, pilot plant and commercial operation.

Jan 1, 1982

By P. L. Sibrell

Three different refractory carbonaceous gold ores from the Carlin operation in northeastern Nevada were investigated to characterize the effect of passivation treatments on the nature of the carbonaceous material. The carbonaceous material was chemically isolated from the ores and passivated residues, and examined by FTIR spectroscopy, elemental analysis, and gold adsorption capacity. The main component of the carbonaceous material in these ores was found to be a naturally occurring activated carbon-type compound. Hydro-carbons were detected on rare occasions, but no evidence was seen for humic acids. Ore samples were passivated by autoclaving, or by treatment with sodium hypochlorite or gaseous Chlorine. In some of the passivation tests, a new peak was observed in the IR spectra of the isolated carbonaceous material, that was due to carbonyl functionalities. However, all of the passivation treatments tested decreased preg robbing significantly. This suggested that the appearance of the carbonyl peak was due to the severity of the conditions during passivation, rather than the method used.

Jan 1, 1990

By Andrew J. Petruska, Rik Banerjee

This study explores implementing a machine learningbased system to generate a 3D surface repre- sentation of the roof and support straps in the mine. Event cameras have been chosen for their performance in high-dynamic-range lighting conditions and for their low latency. To enable automated drilling and bolting, 3D vision using eventbased cameras has been developed. A ground-truth set is created using two, time-synced event cameras and a LiDAR camera. These sensors are used to construct a ground-truth dataset of corresponding event- camera images and surface maps from the LiDAR. The network is tested with stereopairs of event images and produces a depth image with ±5 mm RMS error on average across 1000 test images.

Feb 1, 2024

By A. Bieg, M. Samson, Z. Bell, A. Zinsser, J. Schuyler

As the world progresses toward the renewable energy transition, the demand for minerals increases exponentially. According to the International Energy Agency (IEA) 2021 Net Zero by 2050 Report, critical mineral production needs to grow six times to combat climate change. It’s estimated that four to seven percent of global greenhouse gas (GHG) emissions come from the mining sector’s Scope 1 and 2 (direct and indirect) emissions. Including Scope 3 (upstream, downstream, and embedded) emissions, the sector accounts for 28% of global GHG emissions. In a typical mining operation, diesel fuel is the biggest source of direct GHG emissions, and haulage is often the main source of diesel emissions. Large haul trucks have been the industry standard for over 50 years and offer flexibility, relatively low capital cost (especially with equipment lease options), and guaranteed technology with known maintenance. The challenge will be to justify their continued use when there are more economical options that lead to significant reductions in GHG emissions. The purpose of this study is to compare five haulage options in terms of GHG emissions, using the methodology defined by the Greenhouse Gas Protocol Scopes 1, 2, and 3 (Category 2). Additionally, this analysis compares operating and capital costs associated with the five haulage options (emerging and proven technologies): 1) Diesel-Electric Haul Trucks, 2) Battery-Electric Haul Trucks, 3) Fuel Cell Haul Trucks, 4) Railveyor, and 5) Conveyor. This analysis looks at the emissions and costs associated with operating the equipment (fuel and electricity), the embedded emissions and costs associated with the construction and installation of the equipment itself, and the associated infrastructure (roads, powerlines, and rail).

Feb 1, 2023

By SONGHE WANG, YI XUE, PENG HOU, CAIHUI ZHU, XUANYE JIAO, Feng Gao

Coalbed methane development is an important way to effectively realize a source of clean energy and reduce emissions of carbon dioxide and other gases. However, due to the low permeability of coal seams, the development of coalbed methane in China has encountered substantial barriers. Protective layer mining can efficiently minimize in situ stress and increase coal seam permeability, thus improving gas drainage and avoiding gas disasters. This study analyzed the characteristics of gas migration and the change in permeability during the in situ stress releasing process through experiments and numerical simulation to study the gas drainage effect of a coal mine in an unloaded coal seam under specific geological conditions. First, a stress–strain-seepage coupled test of coal was carried out, and the evolution features of coal permeability during stress loading and unloading processes were investigated. Second, experimental results were used to develop a mathematical model of coal seepage under mining unloading conditions. Finally, a numerical model was developed based on the real geological conditions of the Wulan coal mine to explore the characteristics of in situ stress release and permeability evolution, as well as the gas drainage process in an unloaded coal seam. By combining protective layer mining and gas drainage technology, the risk of gas outburst is significantly reduced.

Oct 1, 2022

By I. Mikov

Established in the 60-ies, the Zlatna Panega quarry is a cement raw materials quarry supplying 95% of the needs of the Zlatna Panega Cement Plant with limestone, marl and other silica-aluminates. The two major types of raw materials are formed by accordingly dipping strata of Upper Jurassic limestones and lower Cretaceous marls. Between them there is a ?transition-zone? or ?contact-zone? of a high-silica content layer, about 5-m thick, defined as ?flint? by investigations including spot sampling throughout the quarry. For many years this ?contact-zone? layer was neglected due its negligible thickness. Further, with the increasing demand on the quality of the raw materials feed to the Plant and the focus on variability of the chemical and mineralogical components, it was decided not to mine any of the parts of the quarry contaminated by this material, for about three years. The latter had an impact on the availability of operating benches that could result in a substantial decrease in the total recoverable re-serves of Zlatna Panega, particularly with respect to marls. There were considerations for resorting to a partial, selective excavation of the quarry pit with a reduced lifetime for the lime-stones and re-opening of an other (currently in-active) marl quarry at a distance of 6 Km from the Plant. The Quarry Team of the Zlatna Panega quarry was assigned to study the problem. The ?contact? layer was duly confirmed with systematic geological (including mineralogy) studies, statistical analysis of available data, surface sampling and shallow exploration drills, resulted into distinguishing a third type of reserves and their credible subsurface delineation by means of geological 3-D modeling and quarry design. A new quarry design was finally elaborated with a view of providing flexibility in mining, utilization of the total volume of all available reserves and maximizing the mine life of Zlatna Panega quarry. An industrial test took place in December 2005, by using the contaminated parts of the quarry (co-mining of the ?contact-zone? materials) at a contribution of 15-20% in the raw materials mix, as dictated by their contribution in the total recoverable resources of the quarry. The purpose was to investigate the viability of this solution ? in line with improved quarry planning ? without compromising the quality of cement production and the efficiency of Plant Operations. Results were overall successful.

Jan 1, 2006

Two key strategies for a new generation of mining are developing domestic raw material production and doing so in an environmentally responsible way, according to presenters at the 83rd annual meeting of the SME Minnesota Section in Duluth (the 71st annual University of Minnesota Mining Symposium). From technical sessions detailing how to build com-munity support, to a short course on international perspectives in iron ore mining and processing, the two-day meeting emphasized the potential of Minnesota state deposits and the importance of maintaining productive community relations both locally and globally. The meeting of more than 300 mining industry professionals began on April 20 with a traditional convocation celebrating the values of northern Minnesota. The accompanying tradeshow, with a record 131 booths, showed the speed and vigor of the economic rebound. Keynote speaker Scott Anderson, vice president and senior economist at Wells Fargo, stated the prevailing mood of the conference: ?Wow, what a difference a year makes.? With metal prices and sales up and heading higher, he said, it was clear that the production-centered economic recovery is reaching the mining and the minerals industry. However, Anderson sounded a few notes of caution. Serious threats to economic stability remain, including the burgeoning national de?cit, high unemployment and the still out-of-control foreclosure crisis. Overall, he predicted a below-average recovery and stressed the importance of developing a long-term business strategy.

Jul 1, 2010

By J. M. Stewart

The incidence of heat stroke in the South African gold mining industry is today small (less than 1 in 10 6 shifts worked). Acclimatization and selection procedures have been developed and applied throughout the industry, underground working conditions have, and are being improved, and personnel are to-day made more aware of heat stress and its consequences than ever before. Although these actions have, over the years, brought about a steady reduction in the incidence of heat stroke (see Figure 1) the small incidence of heat stroke which persists indicates that heat stress is still a problem. This realization provides the stimulus for the work presented in this paper, which has as its primary objective the development of reliable heat stress limits for men working in South African gold mines. [ ] In keeping with recent trends3I4 the approach followed in this paper is based on the physical principles of heat transfer. Detailed studies of heat transfer from humans have been undertaken,5-l1 and certain of the results form an important aspect of this Paper -

Jan 1, 1980

By Seth Pollak, Jon Hurt, Mark Havekost, David Vardiman, James Schick

"INTRODUCTION The Long Baseline Neutrino Facility (LBNF) Far Site Conventional Facilities are proposed to be sited at the Sanford Underground Research Facility (SURF) located within the former Homestake Gold Mine in Lead, South Dakota. The project involves excavation and support of three large caverns which will house four 10 kT fiducial volume liquid argon (LAr) neutrino detectors and cryogenic equipment, as well as numerous ancillary connecting drifts and chambers. This paper describes the geological setting of the project, the geotechnical investigation undertaken nearly a mile underground and the challenges associated with collection of reliable data in a high stress and geologically complex environment. The layout for the new facility will be presented, along with a description of some of the constraints that will impact construction, including shaft access and working within an operating research facility. THE LBNF PROJECT The global neutrino physics community is coming together to develop a leading-edge, dual-site experiment for neutrino science and proton decay studies, the Deep Underground Neutrino Experiment (DUNE). The facility required for this experiment, the Long-Baseline Neutrino Facility (LBNF), will be an internationally designed, coordinated and funded program, comprising the world's highest-intensity neutrino beam at the Fermi National Accelerator Laboratory (Fermilab) in Batavia, IL and the infrastructure necessary to support massive deep underground cryogenic detectors 800 miles (1,300 km) downstream at the LBNF Far Site at the Sanford Underground Research Facility (SURF), in Lead, South Dakota. The Deep Underground Neutrino Experiment is expected to achieve transformative discoveries, making definitive determinations of neutrino properties, the dynamics of the supernovae that produced the heavy elements necessary for life, and the possibility of proton decay. Neutrinos created by the LBNF beamline will travel on the 1,300 km (800 mi) path shown in Figure 1 leading straight through the earth's crust to intercept DUNE's massive, cutting-edge neutrino detector at the Sanford Lab. No tunnel is needed as neutrinos pass easily through soil and rock rarely interacting with the matter. The DUNE far detector will consist of four modules, each of which will be housed in a cryostat containing 17,000 metric tons of liquid argon target material, providing a 10kT fiducial volume. The LBNF Far Site Conventional Facilities project will excavate and fit out a set of four caverns 4850 ft underground in which to place them."

Jan 1, 2016

By JIAQI JIN, Chen-Luh Lin, Amanda N. Erskine, Jan D. Miller, Shijie Wang

The liberation and exposure of valuable mineral grains in ore particles are of significant importance in understanding the efficiency of flotation separations. A flotation feed sample from the Kensington concentrator was scanned by micro Xray computed tomography (micro-XCT), to determine the liberation and exposure of auriferous pyrite grains. The analysis results suggest a satisfying extent of liberation for particle sizes smaller than 212 μm. Theoretical flotation recovery of pyrite for selected particle size fractions was predicted from the three-dimensional liberation and exposure analysis. The plant flotation tail was also characterized by micro-XCT to identify liberated and partially liberated pyrite particles that might not be collected into the concentrate. However, liberation analysis of the tail sample revealed that the majority of liberated pyrite was recovered in the plant flotation circuit. Trainable Weka, a machine learning segmentation approach, was compared with the Watershed thresholding segmentation for the 106 × 45 μm particle size fraction scanned at a voxel size of 1.85 μm. Improved segmentation of small particles was found using the machine learning method.

Mar 1, 2024

By N. P. Titkov

This paper presents the results of laboratory and pilot plant investigations for the development of efficient methods of beneficiating hematite ores from the Krivoi Rog, Kursk Magnetic Anomoly, Olenogorsk, and other localities. The tests included gravity, magnetic (in a high intensity field), flota¬tion, and magnetizing roasting methods. It was possible to develop efficient beneficiation methods depending on the mineral composition of the ore and degree of dissemination of ore and gangue minerals. The paper shows the relationship between the iron silicate and quartz content of the ore and the technologic indices of the various beneficiation methods. Some of the conclusions based on these investigations and the technical and economic computations related to the cost of one ton of pig iron produced from concentrates obtained by the various beneficiation methods are: 1. If the hematite ore is not disseminated uniformly, it is expedient to use a combined gravity and flotation process. Ore particles up to 50 am. in size are beneficiated by gravity (heavy suspension, jigging, and others) and yield a lump concentrate. The middlings from this process are recrushed and floated; 2. Finely disseminated hematite ores, containing small quantities (less than 5 percent) of iron silicates, are most effectively beneficiated by flotation. Anionic (sulphate soap, tall oil emulsion with various foam depressors) as well as cationic collectors may be used. Depending on the mineral and chemical composition of the ore, it is possible to obtain concentrates containing up to 65 percent iron with an extraction up to 94 percent; 3. Finely disseminated, mixed hematite-magnetite ores may be beneficiated by flotation or a magnetic separation-flotation process; 4. Finely disseminated hematite ores, containing large quantities of iron silicates and earthy hematite ores are most efficiently beneficiated by the magnetizing roasting method. This method will yield concentrates containing up to 68 percent iron with extractions up to 90 percent. Although beneficiation by the magnetizing roasting process is costly, it will nonetheless, when employed on this type of ore, yield the least expensive pig iron.

Jan 1, 1960

By P. Mendoza, R. Siwale, H. Amini, R. Silva, M. Richards, V. Ngcoza, D. Rivera, C. Canaza, R. van Reenen

Development of a realistic flotation model to predict its performance is of paramount importance to the processing plant and operators, a model that accounts for predictive and no-predictive maintenance simulating individual equipment downtime and the effect of it in the metallurgical performance on the flotation bank with final recoveries and grades has a huge advantage on optimizing the flotation circuit/bank in terms of mechanical and metallurgical side. The Model was developed in a dynamic environment that allows for a better and more realistic simulation of the flotation bank. The maintenance model accounts for the Failure rate, Mean Time Between Failures (MTBF), Mean Time to Failure (MTTF) and Reliability (R(t)) those characteristics are combined to a multi-compartment process model that consists of a slurry recovery model, two options of froth recovery models, entrainment and carry capacity as a final check for the system. In addition to the maintenance and process model, a dynamic dart valve model was added to the simulation in order to have a realistic model to control the slurry level at the flotation cell. The paper goes over a study case for a current flotation operation trying to explore all the elements and the simulator to optimize the Rougher flotation bank.

Mar 2, 2022

By F. Djahanguiri

The U.S. Bureau of Mines is conducting research on underground stope leaching of metalliferous ores to minimize the environmental impact of ore processing on the surface and to maximize minable reserves. An aspect of this research is to minimize pregnant solution losses and/or groundwater contamination by leach solutions. Bulkhead design and construction are important issues for solution control and stope leaching economics. A reinforced concrete bulkhead was designed, constructed, and tested for solution control in an underground mine near Idaho Springs, CO. This paper presents the bulkhead design methodology and construction procedure.

Jan 1, 1995

"Foreword by Ren BryceSenior engineer, Freeport-McMoRan, Oro Valley, AZ, USAThe eighth annual Mineral & Metallurgical Processing Division (MPD) student poster contest was held in February at the national SME Annual Conference & Expo in Denver, CO. A total of 33 students presented their work at the poster competition. The competition started in January when the students submitted a one-page abstract for judging. In February, they prepared and presented a poster that explained their research. A panel of judges went to each student and listened as the students explained their research in five minutes.The students worked hard at their research and then set aside time to complete all the necessary steps to enter the competition. The MPD recognizes the effort required to enter and as a result, provides monetary rewards to all participants. The first-place winner receives $1,000; the second, $500; the third, $250; and the fourth through seventh, $200. All remaining students receive $100. All of the students also receive a complimentary ticket to the MPD Luncheon. As in past years, there are separate levels of competition for undergraduates and graduates.Graduate winnersKaustubh Shrimali won first place for researching “The influence of starch in amine adsorption by quartz in the reverse flotation of iron ore.” Venkata Atluri received second for studying “The effect of polysaccharides on bubble attachment at talc surfaces.” Jennifer Galvin placed third for investigating “A novel approach to alkali pug bake for the extraction of rare earth elements from monazite concentrate.” In the fourth through seventh places were Amy Richins, Sumedh Gostu, Brett Carlson and Chris Vass.Undergraduate winnersNestor Santa earned first place for exploring “Copper recovery from waste printed circuit boards.” Cassidy O’Connell received second place for conducting “Performance analysis of CMC in high talc copper sulfide flotation systems.” Catalina Vanegas won third place for examining “Cyanidation tests and pretreatments to recover gold from a refractory ore in Colombia.” Kylie Boyce, Michael Archambo and Pritam Sinha were in the fourth through sixth places.Everyone benefits from attending the student poster competition. The students are able to display their work to future employers, and industry professionals can talk to up-and-coming engineers. Next year, there will be another competition for more posters and networking. Come and enjoy the event and the posters."

Jan 1, 2017

By Wedam Nyaaba, Edward Wellman, Angelina Anani, Eduardo Cordova, Sefiu O, Cluber Rojas, Adewuyi

This study aims to investigate the optimal method for ore pass construction in incompetent rock masses. We evaluated the conventional and raise boring methods based on safety, efficiency, excavation control and ground support for ore pass construction. A stability analysis using analytical Q-raise (QR method) and kinematic analysis methods for ore pass construction with a raise borer before and after grout injection of the rock mass was performed. As a case study, an ore pass (diameter of 3 m, depth of 100 m) within an incompetent rock mass was considered to gain further insight. The rock mass was characterized according to the classification methods Q Barton, rock quality designation (RQD), rock mass rating (RMR) and geological strength index (GSI). The grout intensity number (GIN) method of grout injection was used. The safety factor of less than 1.075 obtained before injection was lower than the acceptance criteria. However, grout injection before raise borer excavation resulted in a safety factor greater than 1.5. Using a raise borer without pre-grouting indicated that the maximum unsupported diameter (MUSD) of the ore pass was less than the required 3 m and equal to or larger than 3 m post-grouting.

Dec 1, 2024

By T. Yegulalp, M. Castaldi

As global energy demands increase, there will be a critical need to employ fuels that have minimal environmental impacts. While hydrogen is considered the ultimate fuel for that purpose, hydrocarbon based fuels will be in use for a considerable time and will probably be the first major source of hydrogen for next generation power systems. The best fuel for this transition will be natural gas because of the high hydrogen to carbon ratio. Natural gas hydrates have the potential to meet the global energy needs for the foreseeable future. The amount of energy stored in natural gas hydrates is significantly more than that of all the other fossil fuels combined. However, most proposed techniques for recovering the natural gas from the hydrate require too much energy input, raise safety concerns or can only recover a fraction of the gas. This paper discusses the technical feasibility of a novel method of gas production in hydrate reservoirs. The method is an in-situ process that creates a point heat source in the hydrate formation. This method not only significantly reduces the energy input, but also has the potential to sequester as much or more CO2 than would be produced from combustion of the natural gas produced, thus making this in-situ methane production technique virtually carbon neutral. Simulations using FEMLAB™ show that the method offers an energy efficient and environmentally friendly way to produce natural gas from hydrate reservoirs. Preliminary results indicate that it is possible to have an energy efficiency of nearly 90% for land based reservoirs for hydrate loadings of 20%. The simulation results also suggest that alternatives to a point source can be employed which may improve the process efficiency.

Jan 1, 2007