Search Documents

By Jan Van Greunen, Mark Vanderzee, David Haug, Geoffrey Hughes, Yiming Sun, Roozbeh Geraili Mikola

"The Sanitation Districts of Los Angeles County is planning to construct a new, approximately 7-mile-long (11.3 km) effluent outfall tunnel to be excavated by TBM and lined with precast concrete segments. Anticipated net operating pressures within the tunnel are expected to approach 3 bar. To counteract joint opening and exfiltration leakage, an approach has been investigated to post-tension the precast concrete tunnel lining with steel tendons. The tunnel alignment crosses several seismically active fault zones, at which installation of steel pipe is proposed as a secondary inner lining to mitigate potential offset displacements. This paper discusses the tunnel lining design approach and methods used to address these unique challenges.INTRODUCTION The Sanitation Districts of Los Angeles County (Sanitation Districts) is planning to construct a new 18-foot-diameter (5.5 m), approximately 7-mile-long (11.3 km) tunnel from the Joint Water Pollution Control Plant (JWPCP), located in the City of Carson, to the existing White Point outfall manifold structure at Royal Palms State Beach (RPSB) (Figure 1). The project is part of the Sanitation Districts’ Clearwater Program, which will improve overall system reliability through the repair and replacement of the existing aging infrastructure. The existing system includes two 6-mile-long (9.7 km) tunnels, 8- and 12-feet in diameter (2.4 and 3.7 m), and four ocean outfall pipes with a maximum capacity of approximately 675 million gal/day (MGD) (2.6 billion L/day). Addition of the new parallel tunnel will increase overall capacity to accommodate peak wet weather wastewater flows of up to 1,262 MGD (4.8 billion L/day) and will allow inspection and repair of the existing tunnels. The new outfall tunnel will be excavated using a pressurized face tunnel boring machine (TBM). Shafts at the north (JWPCP Shaft) and south (RPSB Shaft) ends of the proposed alignment will connect the tunnel to the existing wastewater treatment plant and existing ocean outfalls manifold and during construction act as launch and receiving shafts for the TBM. The tunnel will be excavated from north to south as a single heading."

Jan 1, 2016

By Jorge Ferrero, Andreas Raedle, Uhland Konrad, Michael Dutton, Keivan Pak Iman, Walter Trisi

Strabag, in partnership with Arup, is constructing the Advance Tunnel for the Scarborough Subway Extension (ATSSE); a project by Metrolinx and Infrastructure Ontario (Sponsors). The 10.7 m internal diameter single bore tunnel represents a significant departure from the traditional arrangement of twin subway tunnels in North America. ATSSE is the first-time steel fibers are used to solely reinforce a tunnel of this size in Eastern Canada. This paper discusses the challenges with design and acceptance of SFRC segments and the state-of-the-art numerical models employed to check the joint performance. The advance procurement approach for TBM and PCTL’s procurement to accelerate the project schedule is also presented.

Jun 13, 2023

By J. C. Ashby

Electric utility response to certain amendments of the Clean Air Act has resulted in a production of several types of alkaline coal combustion byproducts. Alkaline combustion byproducts are gaining increasing usage for acid mine drainage mitigation as research leads to a better understanding of their beneficial applications. Since January of 1997, Mettiki Coal Corporation has been injecting alkaline flue gas desulfurization material from Virginia Power's Mt. Storm Unit #3 wet limestone scrubber into abandoned portions of the active Mettiki mine. This paper provides an overview of the key design, transportation, regulatory, and environmental issues faced in the project.

Jan 1, 1998

By Paul J. Smith, Eudomar A. Silva, Quang D. Tran, J. Milton Brooks

The Dallas Mill Creek Drainage Relief Tunnel is an 8.04 km (5 mile) tunnel that will provide 100-year flood protection for impacted neighborhoods in the east Dallas area. “Big Tex” is a main beam gripper TBM capable of changing diameters in mid-tunnel to excavate 2.83 km (9,290 ft) of 11.45 m (37.58 ft) diameter tunnel and 5.21 km (17,095 LF) of 9.93 m (32.58 ft) diameter tunnel. Construction began in April 2018 and is anticipated to be completed in 2024. This paper will discuss the challenges and lessons learned during assembly and re-assembly, start-up and mining with “Big Tex.”

Jun 13, 2021

By H. M. Castrantas

Caro's (peroxymonosulfuric) acid has been reported to destroy WAD (weakly acid dissociable) CN-but, until recently, the technology has not been demonstrated in other than a laboratory setting. During the last two years, Caro's acid has been shown to successfully detoxify WAD CN-in tailings at two large North American gold mines. Using on-site FMC generators, Caro's acid reduced the WAD CN-from 40-55 ppm to below 20-35 ppm WAD CN-, the target range for the two mines. The detoxification costs using Caro's acid were less than 50% of the treatment cost of using hydrogen peroxide, the previous oxidant of choice. In addition to the considerable savings in CN-detoxification costs, lower WAD CN-values were achieved and the detoxification time with Caro's acid was greatly reduced compared to hydrogen peroxide.

Jan 1, 1995

By Giorgio De Tomi, Ricardo Tichauer

Mineral exploration is a critical step for success in mining. However, small-scale mining often ignores exploration best practices. This paper introduces the Tichauer-DeTomi Matrix, a tool for assessment of geological uncertainty in small-scale mining. This matrix, which measures the level of compliance of exploration programs in small deposits with industry best practices, has been applied to three small mining projects in Brazil: an artisanal gold mine in the Amazon, a small-scale manganese mining venture in the Northeast, and a small manganese deposit in the Southeast. The application of the matrix resulted in indexes that reflect the actual level of maturity of the mineral exploration program in each project. Therefore, the matrix has shown potential to be an effective tool for assessment of the geological uncertainty remaining in small-scale mineral projects, as well as to identify priority exploration activities for reduction of risks associated with the geological uncertainty. As a risk assessment tool, the TichauerDeTomi Matrix may be helpful in promoting investment and sustained development in and around small mines.

By Roy H. Werner

The environmental demands on the mining industry coupled with rising production costs have created a need for a low cost sludge removal system. The HYDRA* system meets these demands by offering a unique means of removing settled solids from the bottom of a clarifier or a thickener. This underflow system combines experience and proven concepts to form a low cost sludge removal system. The HYDRA system incorporates a flexible design that can be adapted to any settling area. The components are readily available and cost less than a conventional clarifier or thickener. Existing technology developed by preparation engineers provides for retrieval and recovery of mine preparation plant refuse. However, past retrieval methods have been extremely costly. The HYDRA system, because of its low cost, makes the complete process of retrieval and recovery economically feasible. This allows wasted resources to be converted to a saleable product.

Jan 1, 1975

By J. Sottile, V. Androulakis

Operators of underground coal mine shuttle cars are exposed to numerous hazards including noise, dust and musculoskeletal trauma. The repetitive nature of shuttle car operation leads to fatigue-related incidents and soft tissue injuries. The poor visibility conditions, and dust and noise increase the occupational hazards to the operator, as well to other miners. To reduce the risks for all miners, towards providing a safer working environment for all workers, the introduction of autonomous shuttle cars is essential. This paper introduces a project to demonstrate the feasibility of incorporating autonomous shuttle cars in the underground coal mining cycle. The autonomous shuttle car will be able to localize itself, to map its surroundings and to navigate in an underground GPS-denied environment. It will also navigate efficiently by fusing different on-board sensor modalities, autonomously planning the optimum path and traversing around the mine while avoiding collisions with humans and other static and dynamic obstacles. This will be achieved by exploring and testing different state-of-the-art techniques and off-the-shelf components, and integrating them into existing equipment, i.e., retrofitting an actual shuttle car. Moreover, a modified mining system will be demonstrated which will incorporate the autonomous shuttle car, capable of making real-time decisions, into the mining cycle. The system will regulate the interactions between the autonomous machinery and the human dynamic, with emphasis given to the safety of the workers, and enable the real-time, remote supervision of the mining process. The focus will be on coal mines, where the room and pillar mining method is used. INTRODUCTION The growing demand for mineral supplies combined with the steady decline in the available surface reserves has driven the mining industry to mine deeper underground deposits. These deposits are difficult to access, and the environment may be hazardous to mine personnel (e.g., increased heat, difficult ventilation conditions, etc.). Moreover, current mining methods expose the miners to numerous occupational hazards such as working in the proximity of heavy mining equipment, possible roof falls, as well as noise and dust. In recent decades, the utilization of autonomous machines has evolved in the mining industry to provide increased health and safety to mine personnel and reduce their exposure to adverse conditions. Automation aims to remove the workers from the hazardous conditions which may be present in an active mining area and place them to a more comfortable and safer environment at a distance from the active mining face. Examples of incorporation of autonomous machinery in the mining industry include the fleet of more than 100 autonomous mine trucks that are employed at the Rio Tinto’s iron ore mines in Western Australia for material haulage. There are also semi-autonomous, teleoperated LHD machines employed at several mines around the world (e.g., Sweden, USA, China). However, the operation of the autonomous machinery in these cases is either partial (semi-autonomous, teleoperated vehicles) and of small-scale or occurs at surface mines where GPS significantly facilitates the autonomous navigation of them.

Jan 1, 2019

In this paper, response surface methodology was applied to optimize the experimental conditions for the wet grinding of synthetic rutile. The effects of parameters such as rotation speed, solids concentration and duration of grinding on grinding efficiency were systematically investigated and the process conditions were optimized, using a nonlinear regression model based on central composite design. The statistical analysis of the results showed that in the range studied, the grinding efficiency of synthetic rutile was significantly affected by the rotation speed of the conical ball mill. According to results from analysis of variance, the value of the determination coefficient (R2=0.9989) indicates that the predicted values are found to be in good agreement with experimental values. The optimized experimental conditions were as follows: a rotation speed of 350 rpm, a solids concentration of 27.31% and a grinding time of 50.31 min, respectively. Under optimum conditions, the predicted grinding efficiency of 94.79% is obtained. The experimental values from the validation experiments were well within the predicted value of the model.

Jan 1, 2011

By J. E. Lees

Advanced remote sensing can be a powerful new information tool to help private and public entities make better environmental and resource management decisions. However, some regulated entities are reluctant to develop or use this tool because of their concerns that it will lead to increased risks and costs of environmental legal liability. They fear that new ways of monitoring the environment will increase liability, undermine existing enforcement agreements, reopen compliance agreements, and generally provide a competitive disadvantage to early adopters by accelerating environmental cleanup costs. Others counter that the increased risks are marginal, and that several advantages outweigh these risks, including the opportunity to more effectively manage environmental operations, target and set priorities, measure and track management and compliance effectiveness, provide more defensible environmental assessments and baseline conditions, make and defend optimal siting decisions, and avoid or resolve environmental disputes. This paper offers strategic advice on ways regulated entities can enjoy the benefits of these powerful new information tools while mitigating down-side legal and compliance risks as much as possible.

Jan 1, 1999

By T. J. Fenner

Surface and underground mining operations are often hindered by unknown tunnels and stopes and the precise locations of adjacent workings. Mine safety and planning are adversely affected especially in previously undermined areas where historical records are incomplete or non-existent. The results of several Ground Penetrating Radar (GPR) studies for the detection of known mine tunnels in underground coal; salt, and gold mines are presented. A case study to locate unknown, abandoned mine workings at a surface gold mine successfully located all workings to a depth of 11 meters.

Jan 1, 1992

By Rodolfo V. de la Cruz

This paper describes the development of a modified Goodman Jack method for determining the mechanical properties of rock masses in situ. The modified method consists of the basic borehole loading device and a friction-strain-gauge measuring module. The friction gauges, located in the central portion of the jack, are impressed on opposite quadrants of the borehole walls and the remaining quadrants are loaded by the borehole jack with a uniaxial self-equilibrating pair of forces. The tangential strains generated at the borehole walls are thus measured concurrently with the loading. For ideal elastic materials, the tangential stresses at any point on the borehole walls due to jack loading can be obtained from closed-form analytical solutions utilizing the complex variable method. Complete stress-strain curves for the rock material can then be directly obtained from the tangential strain measurements and the calculated tangential stresses at those points. The continuous data are considerably more significant and reliable than averaged or point data obtainable by other current in situ measuring techniques. Moreover, the advantages inherent to the original Goodman Jack method are also obtainable in the modified method. The suitability of the new method was demonstrated by carrying out a number of laboratory measurements in large specimens of reinforced concrete, aluminum and granite blocks. The results of actual field measurements carried out in sandstone and granite quarries were found comparable with those obtained in the laboratory.

Jan 1, 1976

By Jiachen Wang, Nan Wang, Yang Li

The energy structure and consumption ratio in China determine the practical demand for the collaborative mining of coal and co-associated resources. The multi-layer mining of coal, uranium, coalbed methane, and oil and gas co-associated resources, represented by the Ordos Basin, Junggar Basin, and Tarim Basin, faces numerous challenges. Additionally, coal has been found to coexist with various mineral resources in 33 coal-bearing basins worldwide. The scientific issues related to the multi-layer development of coal related co-associated resources urgently need to be addressed. This paper discusses the unique challenges and potential solutions in the multi-layer development of coal-related co-associated resources. The challenges include large extraction space, high mining intensity, intense overburden movement, rapid surface subsidence, and severe overburden damage due to repeated mining disturbances. Proposed solutions include the establishment of a correlation mechanism between multi-layer mining and the carrying capacity of the overburden environment, analysis of the impact characteristics of multiple field couplings, and exploration of their superposition evolution laws. The paper also proposes the development of a comprehensive evaluation and prediction system for overburden environmental capacity loss, a global sensitivity analysis model for overburden environmental capacity, and an intelligent identification and early warning system based on multi-source information fusion. These solutions aim to achieve scientific and precise mining with minimal overburden environmental capacity loss. And the multi-layer development of coal-related co-associated resources is a complex task that requires a multidisciplinary approach and innovative solutions, and further research is needed to validate these strategies and explore new methods and technologies for efficient and sustainable extraction.

Jun 25, 2024

By James K. Kindig

Hazen Research, Inc., has developed a new process for removing pyritic sulfur and ash from coal. Feed coal is contacted with iron carbonyl vapors, Fe(CO)5, at 190°C which puts a thin skin of magnetic material on the pyrite and ash, but does not affect the coal. Thus, low intensity magnetic separators yield a nonmagnetic coal, low in sulfur and ash, and a magnetic refuse, high in sulfur and ash. Results are given for clean coal produced by this method. A comparison is made between results of the magnetic process and the U. S. Bureau of Mines two-stage flotation process cleaning identical samples of Pittsburgh Coal. Capital and operating costs of the two cleaning methods are discussed.

Jan 1, 1976

By I. Iwasaki

There are many reasons why the US mineral and primary metals industry is in its present state. Undoubtedly, a flood of imported goods in all sectors is playing a major role in the plight of our raw materials industry. Domestic industry is becoming increasingly aware of the importance of its international competitiveness. And we are beginning to wonder what is happening to our technological edge. A number of factors affect the international competitiveness. Engineers cannot do much about some of these factors - labor costs, tax policy, government relations, interest rates, dollar strength, and labor-management relations. Something can be done about technology, however. Some say technology is so easily transferable today. But I would like to believe that we have the ability to apply it better than others. Not too many years ago, "made in Japan" meant cheap and shoddy products. Today, Japan has completely changed its image. The US is beginning to feel the threat from Japan's low-cost, defect-free products with dependable delivery. With worldwide recession and the strength of the dollar, we were shocked at the sudden weakness that developed in America's industries, not only in the international market, but domestically as well. What went wrong and what can we do about it? Senior executives from 300 large American manufacturing companies were surveyed. These executives believe US companies must: • invest in more efficient plants and equipment (27%); • invest in more research and development (23%); • improve the quality of service to customers (23%); and • adopt more aggressive marketing tactics and strategies (14%). Are we not doing enough research? The US has nearly four times as many people engaged in research and spends four times as much for research as Japan (Fig. 1). There is little doubt about the excellence of the US performance in basic science as indicated by the number of Nobel prize recipients. Japan has produced only four winners since World War II. Look at technology trade of five countries (Fig. 2). Again, US performance has been remarkable. An interesting observation here, is that the United Kingdom, another country with economic woes, is also in the black, West Germany and Japan, both with trade surpluses, are net technology importers. It is apparent that the US' performance in the commercialization of new knowledge is much more in question. Japan had $50 billion of trade surpluses with the US last year, which led to some friction between Washington, DC and Tokyo. Comparing the technology trade of Japan and the US in more detail, Japan imports disproportionately large amounts of technology from the US and Europe. This data is rather old, 1978, but the general trend is not too different even today. It is generally believed that scientific research leads to innovative technology, then to economic payoff. But, after seeing the current technological challenge by Japan, we are forced to change this traditional view. Investment in research may eventually lead to economic payoff, but not directly. There is a middle ground between new knowledge and its commercialization. This is an area where the Japanese have been successful. Until the 1970s, many western companies licensed patents to Japan for quick profits. But, in recent years, these companies have become more discrete about the terms of technological transfer. As a result, a number of scientists and engineers are expressing deep concern over the future of technological developments in Japan. A survey was conducted on 450 research managers of private industries in Japan on how they viewed the level of breakthroughtype original research in Japan as

Jan 6, 1986

By T. L. Carstensen

The Miami In-situ mine of BHP Copper is located in Globe-Miami, Arizona. The mine leaches mineralized leach capping over a supergene enriched sulfide deposit, and has produced over 500 million lbs of copper during the last 50 years. The Miami unit has identified several opportunities to enhance and expand in-situ production. A computer block model consisting of strict geologic controls, mineralogy, and metallurgical data was developed to assist in the determination of the leachable copper resource. An understanding of the accessibility and solubility of the resource to leaching solutions and the integration of hydrogeologic and hydrometallurgical information was necessary for completion of this project.

Jan 1, 1997

By Abdallah Khair, Nathalie Risso, Arie Herrera, Victor Tenorio

This study introduces a machine learning strategy to optimize icy regolith extraction from the Shackleton-de Gerlache Ridge using autonomous mining equipment. The model incorporates key parameters—distance, road gradient, vehicle load, speed, recharge logistics, and regolith water content—into a cost framework for excavation, hauling, and dumping. Regression models estimate energy and time requirements; classification predicts terrain navigability; clustering groups craters for efficiency; and K-Nearest Neighbors (KNN) determines optimal routing and scheduling. The system adapts to a six-month daylight cycle to maximize productivity and minimize costs, enabling intelligent planning for sustained lunar resource extraction under extreme environmental and logistical constraints.

Feb 22, 2026

By R. R. Klimpel

The industrial processing of ores containing precious metals such as gold is generally very mining site specific, e. g. McQuiston and Shoemaker (1985), vanZyl et. a1. (1988), Fuerstenau and Hendrix (1990), and Hausen et. a1. (1990). The variety of various mineral processing techniques employed is extensive and includes size reduction, size classification, gravity separation, roasting, cyanidation, chemical and/or bacterial leaching, ion exchange and/or solvent extraction, and froth flotation. Gold occurs in the earth's crust on the average in very low concentration estimated by various sources to be between two and five parts per billion. For a specific ore deposit to be considered as an economic source of gold, generally a concentration of near one part-per million (one gram / Mton) or more is required. From a mineralogical viewpoint, gold often occurs in its native or free form. However, it can also occur as gold compounds of telluride, antimony, and selenium contained within either sulfide minerals such as pyrite, arsenopyrite. and pyrrhotite or, to a less extent, within silicate, oxide, and carbonate minerals. In many locations, alloying of gold with silver is found. The optimal processing method for recovering gold is determined by many factors such as the mineralogy of the gold bearing minerals as well as the associated mineralogy of the gangue minerals, the type of liberation profile of the gold bearing minerals upon' size reduction, and the particle size of the gold itself. Free or native gold particles can vary in size from the extreme of large nuggets to very finely disseminated gold associated in a complex sulfide mineral matrix. Typically free gold particles of several hundred microns or larger are efficiently recovered by one or more of a number of gravity based techniques due to the large specific gravity differential of gold (19.3 to 15) versus typical gangue minerals (5 to 2.7). When gold is associated with a sulfide (usually pyrite) matrix, historically most industrial plants involving size reduction and subsequent liberation have operated in a size range of 50 to 80 percent less than 75 microns. Grinding finer than this has been normally not economical unless the ore has a high gold content in the feed ore.

Jan 1, 1998

By Michael L. Clar

Reclamation of surface mined lands has two basic objectives: (1) the elimination or abatement of undesirable environmental conditions, and (2) the restoration of mined land to its former or more productive uses. This paper addresses some of the planning concepts and site factors that influence the selection of suitable land uses for surface mined lands. Three planning concepts included in the discussion are: (1) mine land planning, (2) comprehensive land use planning, and (3) environmental site planning. The site factors that will influence the selection of an appropriate land use have been grouped into three categories: (1) legal, (2) geographic, and (3) natural. The natural factors are further subdivided into three groupings: geomorphology, soils, and climate.

Jan 1, 1981

By D. F. Doerr, E. Blalock, D. R. Bush, K. D. Cohen

"INTRODUCTION The design, development, fabrication, and test of cryogenic breathing apparatus is part of a much larger effort funded by the National Institute for Occupational Safety and Health (NIOSH) and managed through a Space Act Agreement with the National Aeronautics and Space Administration (NASA) at the Kennedy Space Center (KSC) in Florida. This effort is designed to create cryogenically based life support equipment that is responsive to the needs of miners as required by the Miner Act of 2006. Our goal was to design and build a liquid air based self-contained breathing apparatus (SCBA) that lasted 2 hours and would be used for the egress of miners during a mining accident and be refillable while worn. Therefore, the current report describes tests of an Advanced Cryogenic Breathing Apparatus (termed the ACryoBA) designed to provide miners egressing an emergency situation with a two-hour open-circuit SCBA. The ACryoBA utilizes low pressure cryogenic liquid air instead of high pressure compressed air commonly used in most commercially available SCBA. The ACryoBA can also be self-filled from strategically placed Cryogenic Air Supply and Fill Stations (CryoASFS) initially, and thereafter on the egress route approximately every 1 hour and 30 minutes with a 30 minute air reserve. The ACryoBA evolved originally from a one hour Liquid Air Pack (LAP) developed in the 1980’s for Space Shuttle Rescue forces allowing for longer duration and cool air (Figure 1). It was used successfully for many years, through the end of the Space Shuttle Program. The first attempt at a mine egress pack was the Cryogenic Breathing Apparatus (Figure 2). It was to have a low profile, two hours of breathing, attitude independence, and a simple rapid refill while in use. The CryoBA met the two hour criteria, but with difficulty due to excessive heat leakage caused by the dual 4 liter Dewar design. Much of the stored air was lost as it vaporized faster than it could be used. However, the pack was successful in demonstrating both attitude independence and a simple rapid refill capability. The ACryoBA project was designed to continue the progression and address the deficiencies in the CryoBA. The ACryoBA pack was designed to last 2 hours. It minimizes the heat leakage with a single Dewar and thereby requires less liquid air. The single Dewar design also minimizes weight, making it much more manageable by the user (Figure 3). The ACryoBA complies with 42 CFR part 84 NIOSH certification test requirements. One critical requirement for the ACryoBA is operation in positions other than vertical for periods up to 1/4 (i.e. 30 minutes) of the rated service life of 2 hours; this was accomplished by use of new technology called the “attitude independent pickup” which is abbreviated “AIP.” The AIP, developed by BCS Life Support LLC (patent #8,899,226), has a tube going from the top flange down through the center of the Dewar. At the end it has a flexible bellows and a weighted end. Due to the flexible nature of the bellows, the pickup at the end is free to rotate and follow the liquid level around within +/- 90o of vertical."

Jan 1, 2016