Search Documents

By German Zambrana

The solution of the problem of beneficiation of cassiterite from its primary ore deposits is of fundamental importance to Bolivia. The process today involves a gravimetric treatment of the ore followed by sulphide flotation. During the last year, a cassiterite flotation stage has been added in several plants to treat the slime tailings. Although cassiterite flotation is already economical for the slime tailings and the mechanism of the process are understood, it is felt that further research could improve the results. In the past, considerable amount of research and test ark has been performed to select appropriate collectors to improve recovery, to increa¬se the grade of tin in the concentrate, to minimize the effect of metallic ions like Ca+2, Fe+2 and Fe+3 which prevent flotation, and to increase the pH of the pulp which now it can not be higher than 3.0. It has been reported that the halogen salts (1) like NaCl exhibit special surface affinity for cassiterite but none for quartz. These effect seems to be favourable for the selective flotation of cassiterite from silica minerals. In view of these preliminary results it was decided to follow the research accordingly: OBJECTIVES The objectives of the present investigation are: 1. 0 evaluate the influence of NaCl salts in quartz and cassiterite flotation.

Jan 1, 1971

By M. Misra

The processing strategy for the effective separation of bitumen from low grade (< 10 weight percent bitumen) Utah tar sands by a hot water process differs significantly from that used for the processing of high grade (> 10 weight percent bitumen) Utah tar sands. Excellent separations (coefficient of separation = 0.9) can be achieved for high grade Utah tar sands by intense hot water digestion followed by a modified froth flotation step. Such a technique is ineffective for low grade tar sands. In order to change the characteristics of the low grade tar sand an attempt was made to enrich the bitumen content of the feed to greater than 10 weight percent by recycle of bitumen concentrate to the digestion stage. However the quality of the separation was not improved under these circumstances. Similarly feed enrichment by heat treating the low grade feed with recycled concentrate prior to digestion did not improve the separation. More successful separations of low grade Utah tar sands were finally achieved by modification of the viscosity of the low grade bitumen with controlled addition of diluent. These results of the hot water separation tests and variations in the quality of separation are interpreted in terms of the physical properties of the bitumen and the surface bonding forces operative at the bitumen-sand interface.

Jan 1, 1979

By Levent Ozdemir

The advantages offered by mechanical mining have been demonstrated in the underground mining of coal, evaporites and other soft minerals. Mechanical mining and the advancements in automation technoloogies have been the principal drivers towards the realization of enhanced productivity in soft rock mining. For past two decades, emphasis has been placed on developing mechanical mining technology for hard rock applications, to achieve similar productivity improvements and cost reductions. The benefits of mechanical mining are numerous, particularly in an industry where market conditions continue to dictate higher production and lower costs while maintaining high safety standards. Other benefits of mechanical mining include reduced ground support and labor requirements and the elimination of blast and diesel fumes. These benefits further make this technology an attractive alternative to drill and blast for hard rock mining. Mechanical mining is conducive to full implementation of remote control and automation technologies that are under development to achieve further productivity and safety improvements in underground mining. Mine development has been the main focus area for mechanical miners by manufacturers and mining companies. Potential applications include ore body access, haulage and ventilation drifts, undercut and exploration drifts. The economic use of this technology in mine production is still considered many years away. It would need a major technological breakthrough that would make mechanical rock fragmentation competitive with the large-scale, low-cost production blasting operations.

Jan 1, 1998

By J. Finch, R. McIvor

This paper presents the development of a new grinding circuit steady-state modeling system. It is fundamentally based on the “functional performance equation”, which has now been used to improve the performance of numerous grinding circuits. This equation characterizes the two distinct efficiencies that are at work in a ball milling circuit, and how these relate to overall circuit productivity. It does so based on the particle size chosen to distinguish between coarse and fine (product size) material. Now, by applying it to all the material size classes, a simple yet reliable ball mill model was created. Combined with cyclone recoveries, the complete, detailed grinding circuit performance can be exactly reproduced mathematically by the computer program. It can then be used with separate process equipment application engineering methods to systematically engineer grinding circuit improvements. The development, features, uses and limitations of the system are described.

Jan 1, 2007

By Ivan Hunter, Gary Johnson

In many comminution circuits based on SAG mills, an operating cost penalty is incurred in terms of high unit power consumption. By the addition of a crusher to the circuit, to crush part of the so­called critical size fraction extracted from the mill charge, the power efficiency of the circuit can be significantly improved. Dominion Mining has now incorporated pebble crushing into three of its comminution circuits. The improvements in circuit performance have in all cases been significant, and in some cases dramatic.

Jan 1, 1991

By M. Tomono

Harima Works is operating as the zinc and lead simultaneous smelter utilizing the imperial Smelting Process. The smelter commenced its operation in 1966 with designed capacities of 3500 t/M of zinc and 1500 t/M of lead. After that, owing to the results of progressive developments and improvements in operating efficiency and equipments, it has doubled its production figure. This report reviews our recent developments carried out from 1983 to 1985. Firstly, the furnace bottom design was modified for the purpose of reducing carbon consumption ratio. As a result, shaft operating condition has been satisfactory and carbon consumption ratio was improved by 2%, in addition, furnace zinc production was increased by about 8%. Secondly, the oxygen enriched operation at sintering machine was tested from July 1984 to June 1985, in order to increase the sinter productivity, and to solve the capacity imbalance between sinter plant and ISF. As the test result, it was found out that sulfur elimination rate was increased by approx 10% with the oxygen enrichment of 500 Nm3/hr.

Jan 1, 1986

By John J. Reed

Since the beginnings of, the human struggle for survival and improvement, mining has been one of the basic endeavors of life. Until relatively recent times it was classed as an art. Now we are at work trying to, raise mining to the level of an engineering science where it belongs if we are to prosper. It should be self-evident that this goal can be attained only through industrial progress: based on education and research. It is true that our industry, left to itself, will develop a few new ideas and techniques through the years. However, we mining&apos; engineers are relatively few in number compared to the other disciplines, and the rate of our improvement by such "accidental" discoveries is simply tooslow to keep pace with the rest of our technical civilization. It will be evident in the remarks that follow, that the rapid development of mining education, research, and the industry are extremely interdependent, and will be largely controlled by the amount of cooperation, support, and cross-fertilization that can be developed among all three.

Jan 1, 1961

By R. H. Grau, C. D. Taylor, A. L. Martikainen

Utilization of belt air in underground coal mines has been discussed extensively during the last decade. The Final Report of the Technical Study Panel on the Utilization of Belt Air and the Composition and Fire Retardant Properties of Belt Materials in Underground Coal Mining formed by the Mine Improvement and New Emergency Response (MINER) Act of 2006 recommends research on leakage, use of booster fans, and escapeway safety. This paper discusses the role of ventilation modeling in evaluating primary escapeway pressurization in a three-entry development system to improve emergency escape in a coal mine using belt air. The intake entry of the National Institute for Occupational Safety and Health (NIOSH) Bruceton Experimental Mine was pressurized using a 1.1-m (42-in.) diameter, 37 kW (50 hp) fan. The work details air movement in the simulated three-entry system and the resulting leakage patterns. Three mine ventilation software packages were compared to analyze their performance in predicting the airflows and leakage conditions with different fan settings. NIOSH researchers found that the measurement results correlated well with the results of modeling.

Jan 1, 2010

By D. I. Phillips, P. J. Bethell

This paper focuses on the -1/2 mm cleaning at Elk Run Coal. The original circuitry incorporated desliming cyclones. Problems with slimes entrainment in the cyclone underflow (froth cell feed) resulted in poor froth cell selectivity. Laboratory test work led to the installation of high frequency desliming screens. Consequently, great improvement in cell performance was brought about by enhanced desliming with the ability to use split flotation. The modifications resulted in significant improvement in total plant performance and overall yield while maintaining clean coal quality.

Jan 1, 1987

By Carmel Bofinger, Maureen E. Hassall, David Cliff, Eric Stemn

Incident investigation is of utmost importance in most high-risk industries and is often used to improve organisational safety. This study was undertaken to examine the content of past incident investigation reports to determine the effectiveness of the incident investigations. The study uses a semi-quantitative method to assess the effectiveness of incident investigations in the Ghanaian mining industry by evaluating the quality of past investigation reports. The assessment tool consists of five elements with several indicators and rating scales for assessing the quality of an investigation report as a measure of the effectiveness of the investigation. The method was applied to 304 investigation reports of three Ghanaian large-scale gold mines, and the results correlated with incidence rates of the mines to determine if any relationship existed. The results showed that the mines differ significantly in the quality of their investigation reports, suggesting differences in the effectiveness of their investigations. In addition, the incidence rates of the mines negatively correlated with some elements of the assessment tool. In general, the method was found useful and revealed areas where improvement is needed.

By James E. McTurk, Sheldon B. Bland, Roger E. Melley

During the first fifteen years of operation at the Syncrude facility in northern Alberta, numerous improvements have been made in the field of ore conveying. The unique nature of the material conveyed coupled with the wide range of environmental conditions encountered results in a number of unparalleled challenges. Most of the improvements have been brought about with the use of detailed field evaluation. This paper outlines some of the programs which have been run to optimise belt and system construction, and conveyor performance and utilization.

Jan 1, 1993

By F. L. Jackson

The large scale transportation and storage of sulphur in the liquid state is a relatively new development, but is really only a logical extension of old mining and processing techniques, It is not known who the first person was to win a relatively pure sulphur from ore by melting, but this method was commercially used at least two hundred years ago in Sicily and is still in use today. The Frasch process of mining was invented over sixty years ago, and the development and improvement of-liquid sulphur pumping and handling techniques has paralleled the growth in the Frasch mining industry. During the last fifty years, improvements in the technology of using sulphur have included the premelting of sulphur prior to its being burned for acid production or conversion into CS2 and other compounds. Yet, until fairly recent times, sulphur produced as liquid has been solidified into large blocks at the producing point, broken down by blasting or with mechanical equipment, and shipped in bulk form as a solid.

Jan 1, 1962

By Ravi Ray, Kostas Kaklis, Zach Agioutantis

"Modern underground mining is becoming more complex and geotechnically challenging. The engineer uses numerical, analytical, and data-driven methods (empirical and/or experimental) or their combination to overcome these challenges. Each method has its advantages and disadvantages. Nevertheless, given the amount of innovation and experience involved in developing each of these techniques, it will be prudent to use all their benefits rather than favoring one technique over the other. Pillars are the most important support element in an underground mine. A holistic geo-mechanical solution needs to be determined to design mine pillars using a proper sequence and exact mix of the three methods. A combination of these methods, in sync, can encompass the several advantages of the three methods while eliminating their disadvantages. This paper presents a conceptual three-tier solution to the pillar design problem, to improve its design pedigree, using a proper combination of numerical, analytical, and data-driven methods. At the focus of this proposed method lies the Ground Reaction Curve (GRC) concept.INTRODUCTIONAlthough the stability analysis of underground excavations is a challenging problem, its understanding has improved tremendously over recent years through the use of improved tools and techniques. The trial and error method was replaced with more scientific methods like the empirical and analytical methods that are still in use today. Empirical methods were developed based on large data sets obtained from experiments and observations (e.g., coal pillar strength equations). Analytical methods were developed based on mechanical understanding of stability (e.g., safety factor for vertical pillar loading, Convergence Confinement Method). Improvement in computing power and numerical techniques led to the development of several numerical methods (e.g., finite difference, finite element) suitable for geo-mechanical analysis.Each of these methods have certain advantages and limitations. Nevertheless, the user is often puzzled over the proper method selection and over the proper sequence of using them. This exercise becomes more challenging when different methods are combined, where, for example, one has to estimate the pillar strength based on empirical equations (e.g., Mark-Bieniawski coal pillar strength equation), determine the factor of safety based on an analytical approach (e.g., tributary area load divided by pillar strength), and analyze pillar-strata interactions using numerical analysis (see Esterhuizen, Mark, and Murphy, 2010b).Challenges increase when current pillar design methods are designed as passive structures to balance the fixed dead weight of the overburden. This classic suspension design approach does not recognize the self-stabilizing capacity of the overburden (Frith and Reed, 2018). A practical solution to address these issues is the use of numerical analysis. However, one should always keep in mind that the numerical modelling approach may have certain practical limitations."

Jan 1, 2019

By Paul D. Tomlingson

Will Rogers unwittingly commented on the essence of evaluations when he said: "We don&apos;t know what they don&apos;t know!" In so doing, he explained why managers have an obligation to verify that their personnel really know what is expected of them. Rogers further stated that "What we know may not be so!" Here, he suggests that managers must establish the correctness of facts on which they make decisions concerning the future of their organizations. Yet, there are some managers who may not have considered this basic wisdom. These are perhaps the ones who shun a solid, fact-finding evaluation. Instead, they trust to guesswork as a basis for attempting improvement. Without realizing it, they may be making incorrect decisions harmful to the very organization they are trying to improve. Unfortunately, an attitude of avoiding evaluations often permeates whole organizations when their managers fail to appreciate their importance. Recently, the following was found prominently displayed in the office of a maintenance manager. Regrettably, the facts of a subsequent evaluation established how imprudent his attitude was:

Jan 1, 1991

Bigger is indeed better in today&apos;s surface mining operations. That is especially true regarding haul trucks. Building larger, "supersize" trucks, however, means designing more powerful engines and drive systems that are also more efficient and environmentally friendly. And miners are demanding that these trucks have longer service lives with minimum maintenance. So truck makers are teaming with engine manufacturers and mining customers to design these larger trucks that will ultimately lead to reduced mining costs. About 180 of those truck makers, engine designers and miners gathered in Tucson, AZ in September to discuss the state of haul trucks in today&apos;s mining environment. Haulage 2000 was sponsored by World Mining Equipment and attracted attendees from around the world. Manufacturers described the latest in haul truck advancements. These included the design of more powerful engines, improvements to mechanical and ac and dc drive systems and suggestions on how to reduce maintenance spending. Technology improvements in tires for larger struck was discussed as was the cost efficiency of new, lighter-weight bed liners. The following is a summary of a handful of the presentations.

Jan 1, 1997

By R. L. Grayson, S. Yuan

A stochastic model for evaluating the impact of the reliability and maintainability of shovels and trucks on the operational effectiveness of shovel-truck mining systems is presented. In the model, the Markov modeling technique is used to analyze the operating status of a shovel-truck mining system. Then, simulation is used to study the productivity of a shovel-truck system in a particular state. Finally, the relationship between the effectiveness of a shovel-truck system in terms of productivity and the reliability and maintainability of equipment is established. This relationship may be very useful to mine managers in making decisions in surface mining (e.g., regarding production process control, equipment replacement, and maintenance planning). A quantitative study is given to demonstrate how the reliability and maintainability of equipment affect the system effectiveness and how to pinpoint the parameter that has the most significant effect on the system effectiveness. The quantitative study indicated that in order to improve the system effectiveness significantly, the reliability and maintainability of the equipment need to be improved simultaneously.

Jan 1, 1995

By L. Cheng

Almost all modern cutting bits use a cemented tungsten carbide tip to provide adequate hit life against wear. Laboratory tests by the US Bureau of Mines have indicated that the number of strikes for ignition increased by a factor of three with a new non-rotating bit impacting a sandstone block when the clearance angle was increased by 10°, and that carbide-tipped bits allowed more strikes before ignition than steel-tipped bits by a factor of 7 to 10. Recent field tests in an operating coal mine indicate a dramatic reduction in the frequency of frictional ignitions and improvement in hit life by using a mushroom-shaped hit cap and a larger initial clearance angle. The latter was achieved by increasing the hit attack angle. Improved hit performance through selection of the grade of tungsten-carbide is a com¬promise between fracture resistance and wear resistance. A large clearance angle should he maintained by various techniques, such as a variable attack angle holder, or a reusable hit that can he reground.

Jan 1, 1990

A new separator, known as the HydroFloat cell, was developed to overcome the limitations of traditional flotation cells in recovering coarse particles. The HydroFloat cell separates particles based on differences in mass after the selective attachment of air bubbles to the hydrophobic component of the feed stream. Proof-of-concept testing, utilizing phosphate matrix, heavy mineral sands and anthracite slag, indicated that significant improvements in separation efficiency can be achieved using this air-assisted teeter-bed system. Based on the encouraging laboratory results, a pilot-scale HydroFloat cell was fabricated and installed at a central Florida phosphate plant. Test data collected using the pilot-scale unit suggest that the BPL recovery of the +35-mesh plant feed can be increased by snore than 40% through the application of this new technology. This improvement is particularly beneficial due to the very high grade (-73% BPL) of the +16-mesh particles in the HydroFloat concentrate. This article describes the theoretical basis for the development of the HydroFloat cell and provides an overview of recent laboratory and pilot-scale test results.

Jan 1, 2002

By Michael J. Howes

The nature of business in a free enterprise system is to maximise the return on an investment i.e. to maximise the wealth of the shareholders. This is normally achieved within constraints dictated by many agencies, one of which is the health and welfare of the employees. In the mining industry considerable effort has been expended in improvements in this field, however, the major problem still confronting the practicing ventilation or environmental engineer is the determination of what standards he should design for, which satisfy both the economic and health requirement s. Normally the basic health requirements are satisfied by the minimum standards defined in regulations and codes of practice. These are, however, based on an acceptance of a certain risk or lower production potential. A prime function of the ventilation engineer is therefore to financially justify and implement improvements to both standards and systems. The main purpose of this paper is to examine the basis and techniques of providing this financial justification. Changes in existing methods to achieve the same standards but at lower costs are also covered.

Jan 1, 1980

By David T. Kao

The energy situation the world faced during the decade of the Seventies resulted in actions throughout the free world to reduce its dependence on OPEC oil. Many nations heeded the indicators early in that decade and commenced efforts to reduce their oil requirements. Those nations which did not heed these warnings had the message brought to them more emphatically in the last portion of the decade with the further rapid and continuing rise in prices of OPEC oil. Furthermore, the demonstrated unstable nature of large oil-producing countries has made it clear to all free world nations that their energy demands of the future must be provided for by some more stable and assured supply. Now, early in the decade of the Eighties, we see the need for expanded use of coal as an energy supply to be essential. The result in 1980 and 1981 has been a great increase in demand for steam coal worldwide. In essence, a new business for the United States has developed in steam coal export. In the United States, the large growth in foreign demand for our steam coal is now well recognized and documented. A major impediment in meeting this growing demand became abundantly clear in 1980. This impediment is the congestion existing at U.S. coal export ports. With the recognition of this constraint, a plethora of activity has been observed in announcements for alleviating the problem by improving and expanding current export port facilities. In addition to improvement and expansion, an abundance of totally new facilities has been announced in an effort to find ways to meet this large demand in the new business of steam coal export. This is needed; and hopefully, many of these plans will be translated into action. While total implementation of all stated plans is not expected, much of the implementation depends upon large- scale dredging, large waterside ground storage sites, and improved handling equipments in the conventional type of export ports. The time and capital required for implementation is great, and environmental problems associated with dredging are substantial. Host significantly, and unfortunately, implementation that does include dredging our ports will still not permit use of the truly large colliers of 140,000 DWT and greater, which are evolving as the "state of the art" in long-distance sea transport.

Jan 1, 1981