Search Documents

By Thomas W. Smelser

A full-scale geotechnical model of a 15-foot (4.6 m) wide coal mine entry in correlation with computer finite-element analysis (FEA) is being employed at the Bureau of Mines Spokane Research Center for basic research on roof-bolt support systems. Physical and computer modeling of various coal mine roof-bolt reinforcement systems will increase our basic knowledge of how roof supports function. This information, in correlation with computer FEA and underground verification tests, will provide a basis for establishing safer, more cost- effective roof control plans and help establish guidelines for employing fully grouted and conventional bolting systems. The basic rationale for the research, research approach, methods and equipment employed, results to date, and future research plans are described in this paper.

Jan 1, 1982

By James J. Brady, Kenneth L. Faught, Chadi El Mohtar, Chaoshi Hu

"During construction of a 9.5-ft. diameter sanitary sewer tunnel, the City of Edmonton encountered a large pocket of flowing sand that flooded their TBM and caused significant surface subsidence, stopping further tunneling by the TBM through this zone. A unique collaborative effort ensued between the authors representing the city, consulting engineers and academic researchers to develop the optimal strategy for grouting the problematic soils. The site has a layer of very find sand between 20 and 30 ft. in depth with fines contents ranging from 5% to more than 40%. The collaboration extended from requesting additional site investigation efforts to shipping samples to the UT-Austin laboratories for grout testing plus ground and grouting characterization tests resulting in field recommendations for a full scale ground improvement program. New research information on the grouting of fine sands along with a collaborative framework for the design of in-situ grouting projects are the key topics presented. INTRODUCTION Encountering a large unexpected pocket of flowing sand with an open-faced TBM while excavating a tunnel below the groundwater table is never a good thing. This was certainly true for the City of Edmonton when one of their Lovat TBM’s became inundated by flowing sand while excavating the 9.5-ft. diameter Millwoods Double Barrel Replacement Tunnel in September 2013. However, since the City of Edmonton self-performed this work, a rare situation existed where the site could be investigated objectively, without the prejudice of contending parties selectively influencing how information was gathered and presented, to accurately examine site conditions with a goal of identifying the best remediation measures."

Jan 1, 2016

By S. A. Richards

Business planning in the coal' industry revolves around the production and quality forecast. It is difficult to accurately estimate costs and revenues until the production forecast is made. At mines where production comes from multiple sections, quality is tied to each section's production. Blending becomes a part of the planning process. In order to respond to rapidly changing business climate, a reliable program is needed to accurately forecast the effects of changes in key parameters affecting the production. This paper discusses an efficient, intuitive, and economical approach to underground coal mine planning program which uses a PC-based relational database as the programming platform to forecast production and quality. The program was developed at a major coal company. The relational nature of the production planning data, the programming algorithm, and the underlying principles are discussed in this paper.

Jan 1, 1994

By K. L. Kayler

The Bardon Trimount, Inc. stone quarry in Ashland, Massachusetts was the recent subject of a quarry closure review report. The quarry produces aggregate using standard drilling and blasting techniques. Stone is processed at an on-site plant. Noise monitoring data collected during the closure review indicate that the quarry generally operates within the quiet range. There is a decrease in noise while the quarry is not operating. Levels of dust associated with the quarry are low. Unpaved roadways are the greatest contributors of fugitive dust associated with the mining operation. The quarry cannot be seen from any homes within the town of Ashland, except during the winter months. The visual impact of the quarry on surrounding properties is minimal. Further quarry development is likely to reduce visibility of the quarry from some areas.

Jan 1, 1995

By T. D. Barkand

A recent coal mine elevator accident resulted in serious injuries to four passengers. The miners struck the ceiling of the elevator car as it collided into the overhead structure at an estimated speed four times faster than normal. In response to mine hoisting accidents, safety authorities have required additional protective devices on new and existing mine hoists and elevators. This paper examines supplemental safety circuits and new devices designed to provide ascending car overspeed protection on mine hoists and elevators. These devices provide needed protection that eliminates the hazard or significantly reduces the potential of a mine hoisting accident.

Jan 1, 1995

By C. E. Jordan

Direct digestion of phosphate ores by the acid-alcohol method offers improved leaching selectivity for the exclusion of iron and aluminum in the product acid. The leaching kinetics of this process will have a major role in the eventual application of this technology. The Bureau of Mines investigated apatite dissolution to determine the reaction rate and mechanisms of the leaching kinetics. The dissolution kinetics were monitored on various sized fractions of pure apatite. The "shrinking-core" kinetics model was applied to the data to determine the rate controlling mechanisms. For each size fraction, the initial reaction rate was controlled by the dissolution reaction. After an hour the dissolution rate slowed indicating a diffusion controlled reaction caused by the formation of calcium sulfate hemi-hydrate coating on each particle. For complete dissolution of the apatite, the phosphate rock should be ground to near 10 µ m size.

Jan 1, 1993

By J. P. Matoney

The operation of a modern coal preparation plant, particularly in western Canada, is a very complex task. Most western Canadian operations are processing two or more, sometimes up to ten, different seams through the same plant. This requires a sophisticated multi-circuit plant that needs close operational control. Add the soft nature and large amounts of natural fines of western Canadian coal and you have a formidable cleaning task. To assist in the operation, programmable controllers and sophisticated control concepts are being more widely used. Two of the newest coal preparation plants in Canada have been designed by Raymond Kaiser Engineers Inc. and its Canadian subsidiary, Phillips Barratt Kaiser Engineering, Ltd. The use of programmable controllers and control systems will be illustrated by showing their application in a "typical" western Canadian coal plant. This example will cover flowsheet design, control concept systems application, and possible future uses.

Jan 1, 1983

By M. E. Orman

Many factors must be considered when designing a heap leach pad. Geotechnical properties of the ore, can and will affect how well an ore leaches, the solution recovery, stability of the heap, and settlement. As a heap is stacked some of these properties will change due to the increased load. In order to properly design a heap these properties should be determined beforehand so that the heap performs as intended.

Jan 1, 1997

By F. H. Seymour

Central to Newmont Gold's Mine planning system is the ability to interactively perform cut and fill operations on topographic contours and to accurately evaluate grades and tonnages within contour outlines using polygon set manipulation routines. This paper develops the applied geometry concepts that underlie these routines. Included are representation of volumes with contours, point in polygon test, block proportion in polygon calculation, polygon area and centroid calculation, and intersection, union, and complement between polygon sets.

Jan 1, 1990

By J. D. Miller, C. L. Lin, J. Dong

Nano clay mineral particles such as kaolinite — with primary particles typically smaller than 2 μm in size — can cause significant problems in flotation processes and tailings disposal, including the processing of Florida phosphate rock and Canadian oil sands. In this study, the consolidated state of flocculated kaolinite sediment was examined, and high-resolution X-ray microtomography (HRXMT) was applied to describe the structure of the consolidated sediment. Using this tomographic information, the complex geometry of the channel network structure for the consolidated flocs was established for the first time. With the establishment of the experimental channel network structure, permeabilities were estimated by flow simulation using the Lattice Boltzmann method. Results for kaolinite sediment with and without polymer are compared and discussed. Results for flocculated kaolinite sediment in a gravitational field are also presented and discussed. The results show that as polymer dosage increases, the permeability of flocculated kaolinite sediment increases, and as suspension pH increases, the permeability of flocculated kaolinite sediment decreases.

By M. S. Celik

Despite its importance in various diverse industries, research on beneficiation strategies of boron minerals has not received enough attention. Boron minerals are primarily upgraded by wet processing methods. However, severe environmental constrains have accelerated the development of dry processing techniques such as calcination. Interestingly, boron minerals, colemanite, ulexite and borax undergo respectively decrepitation (fragmentation), shrinkage and expansion upon heat treatment. Each mineral then requires a different beneficiation scheme. In this study, laboratory and pilot plant studies on calcination of boron minerals conducted in our laboratories are reviewed along with their implications in commercial operations.

Jan 1, 1997

By W. B. Hayes

The origin of the titanium pigment and metal? industries began with the discovery of the element titanium in 1791 by an Anglican clergyman named William Gregor. The titanium was discovered in magnetic black sands found in the beaches near Cornwall. England. The name titanium was established by the German chemist who discovered the mineral rutile in Hungary. Rutile is the oxide of the element titanium, which he called titan alluding to the mythological titans, giants of ancient Greece. The commercialization of titanium minerals began probably in 1916 with the production of titanium tetrachloride which was to be used in tracer bullets, flares and smoke screens during World War 1. In the 1920's composite pigments based on TiO2 barium sulfate and calcium sulfate were produced, followed by the introduction of the sulfate process anatase TiO2 crystal in the 1930s. The U.S. Bureau of Mines in 1938 began investigating titanium metal technology and promoted the development of the Kroll process. which is the magnesium metal reduction of titanium tetrachloride to produce titanium metal sponge.

Jan 1, 1989

By P. -J. Kleiterp

Highwall mining is a mining method to extract coal from a final boundary in open cut mining, trench mining or contour mining. This boundary may have been reached because of economic constraints (economic strip limit) or geographic constraints (spoil heaps, rivers etc.). Coal is mined from visible, horizontal, or near horizontal coal seams by making rectangular, parallel, unsupported drives with an unmanned cutterhead and coal transport system. This is controlled from a mining unit, or launch frame, positioned outside the drive, in front of the highwall. Removal of overburden is not required or is limited to small quantities only. Highwall Mining originated in the 1940 in the Appalachian Coal Field. This paper describes the history of the various machines that have been designed for highwall mining. During the 1990 and later, there has been more emphasis on the safety in highwall mining. Many pillar strength formulae have been derived to determine the required width of pillars in highwall mining and, with that, the economic feasibility of highwall mining. The various pillar strength criteria will be discussed in this paper showing the countries where they are applied. In order to make highwall mining equipment safer and more productive, there have been quite some technological improvements applied to the machines. These technologies make highwall mining ready for the future as a serious mining method, also outside its traditional Appalachian mining area.

Jan 1, 2010

By Tamara Nestorovic, Luan T. Nguyen

"With the aim to mitigate excavation risks and reduce the costs caused by tunnel boring machine (TBM) stoppage when tunneling under uncertain soil conditions, prediction ahead of the tunnel face has become an increasing interest in the tunneling community. Our research topic is concerned with developing effective concepts for nondestructive identification of geological anomalies ahead of the tunnel face by waveform inversion of reflected tunnel seismic waves. The authors demonstrate that this new technique is promising in providing tunnel engineers with an accurate image of the geological situation that the TBM is going to encounter thanks to the waveforms’ rich information about the geological structure that affects propagation, reflection/refraction and mode conversion behavior of the elastic waves. By setting up a 2-dimensional numerical model for simulation of tunnel seismic wave propagation influenced by a dip layer change ahead of the tunnel face, the authors show that the waveform misfit to be minimized by the inversion process is highly multimodal and therefore propose a hybrid stochastic optimization method that can quickly and robustly converge to the global minimum. DEVELOPMENTS IN TUNNEL ADVANCE EXPLORATION Conventional site investigation by drilling boreholes helps to draw a general image of geological structures along the borehole axes but that image is likely to misrepresent the detailed geological structure due to limited sampled locations. Due to high costs and restricted boring space which deep tunneling and tunneling under urban areas encounter, many industrial and academic research groups have had great interest in developing nondestructive ahead of the tunnel face prediction systems. That means only excitation sources and receiving sensors, which are usually placed on the ground surface or on the side walls or on the cutter head of the TBM, are used for acquisition of the measurement data. The recorded signals in the form of seismic or electromagnetic/ electrical waves, which travel through the geological structure or are reflected back from it, hold the signature of the geological structure of concern, such as geological layer changes, fault zones, erratic rocks, boulders, construction remnants, etc., and therefore can be used to reconstruct the spatial and material properties of those hidden geological structures. Most common nondestructive ahead-of-tunnel investigation systems to date are based on interpretation of reflected elastic/ acoustic waves (seismic waves) and analysis of electromagnetic/ electrical resistivity signals (Mooney et al. 2012). However, due to insufficient penetration depth and spread of signals generated by radar and geoelectric sources, the use of seismic waves for ahead of the tunnel face prediction (tunnel reconnaissance) is more preferable (Kneib et al. 2000; Bohlen et al. 2007)."

Jan 1, 2016

By John P. Capp

In recent years limited markets have been developed for fly ash, the dust removed from coal-burning powerplant stacks, but most of it is still dumped in spoils areas at a cost ranging from 20 cents to $1.75 per ton. Aside from this cost, the creation of huge spoils areas can present a considerable aesthetic problem. Since the present annual fly ash output of about 20 million tons will probably reach 30 million by 1970, and because satisfactory disposal areas are becoming more limited, markets for much larger quantities of the waste are needed to keep disposal costs from becoming a significant economic factor in coal-burning powerplant operation. Current stress on air-pollution control and beautification, plus the vital need for good powerplant economy, makes it imperative, therefore, that coal producers and consumers expand markets and develop new applications for fly ash. Markets for established uses can be increased by making a greater effort to sell fly ash. New large tonnage markets for fly ash should be sought via more intensive, coordinated research. The economics of fly ash utilization underscores the vital role that must be played by research. To be competitive with other products, processes for the conversion of fly ash into marketable materials face difficulty in regard to two important economic factors--transportation cost and product utility--the other economic factors are favorable. Raw material costs of fly ash, for example, are quite attractive, and supply is no problem because there are many coal-burning powerplants in operation and many more are planned. Demand for products made from fly ash will grow if their utility is established and a good sales program is initiated. The major problems then are transporta¬tion costs and development of useful products.

Jan 1, 1966

By George Innes

The soda ash business in the United States has undergone a sweeping technological change in ihe last 20 years. In a world where synthetics are continuzlly replacing natural products, here we have exactly the opposite, a syntheric chemical being replaced by a natural product. This change is nearly complete in the U.S. and is beginning to take place in Europe and other parts of the world.

Jan 1, 1980

By John A. Riddle

Some of the pitfalls and problems in selecting and applying corrosion-resistant materials in uranium plants are discussed, together with some suggested solutions. Includes some cost data.

Jan 1, 1979

By Tyler Acorn, Brandon Wilson, Jeff Boisvert

Project-scale decisions in surface mining operations rely on the optimization and subsequent evaluation of pit limits. This process ignores the ability for mine plans to adapt as more information is gathered. Stochastic methods, which consider uncertainty in the pit optimization, generally act to refine the boundaries of the pit on a fine scale. This paper extends uncertainty-based methods to consider unique scenarios through a clustering of the realizations that are being optimized. This results in the generation of multiple sets of similar realizations. A separate pit is optimized on each set of realizations, resulting in the production of a series of planning scenarios. This accounts for the adaptability of mine planning as more information is gained. A decision-making framework is then applied to the resulting scenario plans to select the optimal choice. The improvements stem from the joint uncertainty considered when realizations are grouped that is not considered when the probability of a block being in any optimized pit is considered. Mining operations today can benefit from considering additional planning options as identified and evaluated in this workflow.

By Alfred G. Hoyl

The author, in exploring a virgin area vertically in two known ore shoots requiring decline shaft sinking, drifting, crosscutting and diamond drilling, chose to use electric, electric hydraulic, and diesel rubber-tired equipment. A rebuilt hoist, and electric hydraulic shaft shovel (mucker), hydraulic sinking drills, single boom electric hydraulic jumbo, electric hydraulic LHD, and electric hydraulic diamond drill were used successfully. Slides of the equipment and its use are shown. The advantages and disadvantages of the equipment are discussed, together with costs and production.

Jan 1, 1984

By Connor Langford, Murray Gant, Ken Massé

For public organizations, preparing accurate project cost estimates is a critical component in capital project planning. Project delivery methods provide a structured approach to moving projects through the design and construction lifecycle, and typically use cost estimates as key inputs at each stage to determine if the project will advance. As design stages can occur years or even decades before construction contracts are awarded, estimates need to make reasonable assumptions about how the work may be executed (means and methods) as well as potential future market trends so that appropriate values for material pricing, labour costs, escalation, and owner’s costs can be included. This process is challenging enough during stable markets, as historic trends can often be misleading and require a suitable understanding of economic factors to use appropriately. When you mix in the market volatility that has been observed since 2020, developing accurate project cost estimates becomes even more challenging. In cases such as this, having a structured approach to cost estimating that includes an adequate risk-based reserves cannot be overstated as it provides the basis for ongoing project decisions. This paper explores some of the historic and more recent market trends that have impacted key aspects of project cost estimates for capital project planning. It also provides recommendations on how to develop cost estimates for infrastructure projects, with examples from Metro Vancouver, which plans for and delivers regional-scale services to 2.6 million residents. A brief commentary on the use of escalation clauses in contracts is also presented.

Jun 13, 2023