Search Documents

By Ronald R. Hartman

I can recall a time 10 or 12 years ago when I spent a pleasant Sunday afternoon driving to Jim Thorpe, Pennsylvania to see a carnotite deposit that had recently been discovered. The announcement of the discovery stated that it was in the Pottsville conglomerate in a road cut along the highway. To my surprise, the highway was lined with cars and every weekend prospector for 100 miles had come to see the ?big uranium deposit of the east?. I literally had to stand in line to make a measurement with the scintillation counter I had with me. The thought at first occurred to me that this is evidence of how thoroughly the surface of the United States must have been prospected, more likely, perhaps it points out quite the opposite. A lot of time and energy was being spent in tracing the footsteps of others and a lot of time was spent looking for the obvious occurrences. The point is, that in the early days a tremendous amount of uranium exploration was carried out but few systematic surveys were made. Thorium anomalies were usually discounted after cursory surface field checks. Conversely, in airborne surveys - anomalies due to elevation changes or thin over- burden on hilltops were often investigated more thoroughly than smaller indications on hillsides and valleys. An adequate supply of uranium was nevertheless found due to the ingenuity and persistence of the geological profession and the public in general. This ?adequate? supply, like so many estimates for raw materials turned out to be far too low.

Jan 1, 1967

By John Dodd

Corrosion studies in laboratory ball mills and grinding environment simulations produce corrosion rates and total metal removal rates much lower than those recorded in operating production ball mills. The corrosion component of ball metal loss in commercial mills represents less than 10% of the total loss expressed as micrometers/hour of exposure in recent USBM tests. Such small absolute losses are consistent with ball metal loss measured in production ball mill marked ball wear tests to determine effects of corrosion and abrasion resisting properties of alloys in operating mills which indicate that metal hardness and microstructure determine relative metal loss rates of a given situation. The combination of ore characteristics and grinding process dynamics determine metal loss severity. Alloying for corrosion resistance and modification of the milling corrosion environment yield relatively small metal loss reductions. Alloying and heat treatment to produce high hardness and microstructures of high carbon martensite and for cast irons, M7C3 carbides produces the lowest metal losses in typical wet grinding applications.

Jan 1, 1984

By C. C. Clark, D. J. Benton, J. B. Seymour, L. A. Martin

"The U.S. National Institute for Occupational Safety and Health (NIOSH) is conducting research on jackleg use and related accidents in underground metal mines. This paper provides an analysis and overview of jackleg drill usage, accidents, operational characteristics and alternatives, based on information from injury reports, legacy research, stakeholder input and published literature. The results indicate that jackleg drills are involved in more groundfall accidents in underground metal mines than any other drill, and jackleg-drill-related injuries are most prevalent at the face in the course of installing initial ground support. Practical mechanized alternatives to jackleg drills for drilling and bolting under incomplete support in narrow underground openings have not yet been realized. Small, versatile mechanized bolting equipment needs to be developed to address jackleg-drill-related accidents and improve safety at mines where jackleg drills are being used. IntroductionJackleg drill is a generic name for a handheld, rotary, percussion rock drill equipped with an attached reaction leg to provide stability and thrust (Fig. 1). All of the drill and leg controls are located near the operator’s handle at the rear of the head portion of the drill. Jackleg drills are classified according to the bore size of their pneumatic pistons, which normally range from 6.03 to 8.26 cm (2.375 to 3.25 in.) (Kurt, 1982; Clark, 2012). Jackleg drills typically weigh 46.7 kg (103 lb), but the weight can approach 54.4 kg (120 lb) after being fitted for operation with drill steel and air and water hoses (McKibbin and Clark, 2001). In underground mines, jackleg drills are commonly used to drill 3.8-cm (1.5-in.) diameter holes up to 1.83 m (6 ft) deep in rock."

Aug 1, 2016

By L. Yuan, J. H. Rowland

"In 1995 and 2003, the U.S. Mine Safety and Health Administration (MSHA) conducted surveys to determine the number of atmospheric monitoring systems (AMS) that were being used in underground coal mines in the United States. The survey reports gave data for the different AMS manufacturers, the different types of equipment monitored, and the different types of gas sensors and their locations. Since the last survey in 2003, MSHA has changed the regulation requirements for early fire detection along belt haulage entries. As of Dec. 31, 2009, point-type heat sensors are prohibited for use for an early fire detection system. Instead, carbon monoxide (CO) sensors are now required. This report presents results from a new survey and examines how the regulation changes have had an impact on the use of CO sensors in underground coal mines in the United States. The locations and parameters monitored by AMS and CO systems are also discussed.IntroductionThe last survey conducted by the U.S. Mine Safety and Health Administration (MSHA) on atmospheric monitoring systems used in underground coal mines in the United States was in 2003 (Francart, 2005). A total of 146 active mines were surveyed. The survey report states that since 1995 there had been a steady increase in the use of atmospheric monitoring systems in underground coal mines as the technology of carbon monoxide (CO) sensors was improved by manufacturers. Atmospheric monitoring systems had become more reliable, and some CO sensors could be purchased with the capability to discriminate between the CO produced by a fire versus CO produced by diesel equipment. This increase in reliability had reduced the number of false alarms and the response time. The faster response time to a developing fire allowed miners to take the necessary action to put out the fire or exit the mine.At the time of the last MSHA survey, some mines still used point-type heat sensors to detect the presence of a fire on conveyor belts. This detection method works by measuring the temperature of the air around the sensor. As a fire starts to develop, smoke and hot gases are produced from the combustion process, and the air is heated up. Once the air and gases reach a designated temperature detected by the point-type heat sensor, a fire alarm signal is generated. Studies have shown that the response times for detecting the presence of a fire using CO sensors are much shorter than when using point-type heat sensors (Conti and Litton, 1995)."

Jan 2, 2018

By Bo Kyung Sim, Dae Young Kim, Jae Won Lee, Ebrahim Farrokh

"The contract C931 of the downtown line 3 (DTL3) mass rapid transit system of Singapore includes half a kilometer twin tunnels running between Mattar and Macpherson stations. An EPB TBM of 6.6 m diameter was used to excavate both of these tunnels. The tunnels pass predominantly through a very stiff silty/clayey fine to coarse sand from the Old Alluvium Formation. In this paper, TBM selection procedure, TBM performance evaluation, and some of the tunneling operation challenges with the TBM in the Old Alluvium Formation are discussed. In this regard, soil conditioning trial tests were performed to resolve the clogging issue and low TBM performance. Thorough TBM operational data analysis was performed to detect high soil abrasivity, backfill grout leakage, and foam nozzle clogging. The results of some of the applied modifications are also discussed to show their effects on the TBM performance improvement. Finally, some of the challenging TBM design specifications are also discussed. INTRODUCTION Tunneling and underground construction in Singapore has been increased in the last 30 years due to the demand for public transportation systems and the limited space above the ground for the infrastructure development. Downtown Line Stage 3 (DTL3) Mass Rapid Transit (MRT) system has 21 km total route length and consists of 16 stations. DTL3 Contract C931 runs between Mattar station and MacPherson station. The construction works in this contract include twin bored tunnels of 6.6 m diameter and 450 m length and a TBM launch shaft of nearly 30 m depth. The tunnels run in urban area below Kallang Paya Lebar Expressway tunnel (KPE), Kallang River Canal, and Circuit Link. Figure 1 shows the alignment of the tunnels in between two subway stations. The tunnels were excavated by an earth pressure balance (EPB) tunnel boring machine (TBM) through the Old Alluvium (OA) formation, a challenging geological formation in the sense of its abrasivity and stiffness. The Old Alluvium Formation mostly includes stiff to very stiff clayey and silty sand. The soil is un-weathered cemented to semi-cemented dense, mainly with a low permeability coefficient of 10-7 m/s and high SPT values (almost 100). The soil is classified as “very high abrasive” according to NTNU SAT test classification (SAT value of 15 to 42). The construction of the first tunnel drive was slowed down due to a number of factors related to soil conditioning and TBM operation. In this regard, a thorough analysis of the TBM operational parameters from the excavated sections was performed to identify the problems in time to prevent unwanted construction delays in the subsequent sections. In the following sections, a brief overview of the criteria used for TBM selection is presented at first. Then, the results from the analyses and tests performed to assess soil conditioning, grout leakage, and soil abrasion are presented. The last section discusses some of the tunneling design features that challenged the TBM operation in this project."

Jan 1, 2016

By M. Fan

Coal has in general a wide range of density from minus 1.3 to plus 2.0 g/cm3 because of its variations in purity, rank, and porosity, etc. The coal density has great impact on froth flotation performance, but much less attention has been paid to particle density than particle size. Our previous research results demonstrated that cavitation-generated nanobubbles around 700 nm in diameter can significantly improve coal and phosphate flotation performance over a wide particle size range. In this study, the effect of nanobubble on the flotation performances of different density fractions (minus 1.3, 1.3-1.4, 1.4-1.5, 1.5-1.6, 1.6-1.8, 1.8-2.0, 2.2-2.2, and plus 2.2 g/cm3) of coal was investigated using a bank of 10-liter flotation cells, a specially designed 50-mm-inside-diameter column, and a 152-mm-inside-diameter column. It was found that nanobubble has the biggest impact on the flotation performance of 1.4-1.8 g/cm3 medium-density coal particles.

Feb 23, 2014

By Luzheng Chen

The study aimed to evaluate the separation performance of a full-scale continuous centrifugal concentrator in the reconcentration of fine hematite from high-gradient magnetic separation (HGMS) concentrate in a tailings recovery plant, and to investigate the usefulness of the technology in industrial applications. The effect of changing the operating variables on concentrate grade and recovery was studied. The results indicate that among the variables considered in the study (water spray pressure, centrifugal acceleration, feed volume flow rate, feed percent solids and the reciprocation and spacing of water sprays), the change in centrifugal acceleration affects the recovery the most and continuous concentration can be achieved only when the water spray has a sufficient pressure. In addition, the reciprocation and spacing of the water sprays have a significant influence on the concentrate grade. Although performance of the full-scale concentrator is slightly inferior to pilot-scale trials, due to limitations in the scale-up design and the fluctuations of feed material characteristics, this concentrator provides a potential way to achieve continuous concentration and obtain a high-grade concentrate from tailings.

Jan 1, 2010

"Tell us how you got involved in mining and about your career path.My dad was a coal miner and my uncle was a metallurgist, so when I enrolled at Penn State’s New Kensington Campus, I chose the College of Earth and Mineral Sciences — exact majors didn’t get picked till the end of your sophomore year. Penn State New Ken had an associate degree in mining program and one of the guys in my carpool was going to take Mining 30 in the evening and the other guy (mechanical engineer) was also able to take an evening class. I didn’t want to break up the carpool, so I took Mining 30, complete with essay tests. I could write, so I did well, and the professor said I should go into mining engineering. Fast forward to the end of the next term at University Park, and I realized there wasn’t enough chemistry in mining. Switching to metallurgy would have meant another term at that point, so Dr. Lovell, my advisor, trotted me down the hall and to the next building and said I was a mineral processor. That stuck. I was a summer student at U.S. Steel Research between my junior and senior year and they paid for my master’s degree — all about clay and macerals in coal flotation. During that time, the steel industry tanked, and I thought a Ph.D. would be a good idea — I could always teach at the university level if I had those credentials. The Electric Power Research Institute had a Coal Cleaning Test Facility in Homer City, PA, and I conducted my Ph.D. research on rate and residence time in conventional coal froth flotation cells there and at a local cleaning plant. I went to work at the test facility in 1987 (later CQ Inc.) and stayed there until I started PrepTech Inc. in 1997. PrepTech offers some consulting services for coal cleaning plants and sells mineral processing equipment, mostly to coal companies. I can’t believe it’s been 21 years.And what about your SME career?Of course, I was a student SME member at Penn State. We used many of the SME books in class, so who wouldn’t want the student discount? While in Homer City, I became involved with the Appalachian Plateau Subsection of the Pittsburgh Section. We’d hold quarterly meetings with interesting speakers and had good attendance. I was the secretary. I’m still the secretary and also get the bank statements. We’ll need to close that out some time, but I guess I’ve been hoping for resurgence in the Indiana/Cambria/ Somerset area."

Jan 3, 2018

By Douglas H. Bolton

In recent years, equipment manufacturers have been busy developing remote control systems to catch up with the sophistication and efficiency of continuous miners. Now the tables are turned, and manufacturers are undertaking the new challenge of upgrading, refining and equipping continuous miners to take full advantage of the capabilities made possible by modern, successful remote control systems. Because the operator can safely advance the miner farther without pulling out for roof bolting, continuous miners now need to be equipped with means of complying with correct face ventilation, dust suppression, methane detection, diffusion and improved lighting. Some of the exciting possibilities being developed to catch up with remote control include feedback controls using laser beams as datum points, coal sensing devices with feedback signals to show the operator what the machine is doing, show where it is relative to the coal seam, how hard it is working, and more sophisticated use of cyclic control. Mining machinery manufacturers have accepted the new challenges, and faster, safer mining procedures are already in sight.

Jan 1, 1975

By Ray Nivens, Umit Turunc, Caroline Sui, Nick Morrison, Douglas Steiner

"In most copper mines and concentrators, mill water is continuously recovered and reused, with fresh water added to make up for losses. When mixed, these water chemistries can lead to severe scaling, especially in pipes, tanks and pumps on the mill water supply side, reducing flows and causing significant production losses.At KGHM Robinson Nevada Mining Company, increases in the fresh water addition ratios resulted in severe scaling problems and premature pump failures thereby jeopardizing plant production. What initially appeared to be a few isolated scaling events eventually unfolded into a recurring pattern of water supply-related production losses with increasing severity. Through completion of detailed root cause analysis, chemistry modeling, laboratory work, in-plant testing and system engineering, the mechanisms of scaling were identified and addressed.Advancements in fresh water addition practices and antiscalant application methods resulted in a stepwise reduction of the mill water scaling. Cost savings and production benefits were significant to the plant’s financial metrics.IntroductionThe production of mineral and metal concentrates using the flotation process requires large quantities of water. Flotation is utilized as the primary means for beneficiation with sulfide ores. Mined ores are crushed and ground into a slurry of 20-55% solids. For each ton of ore, 400-900 gallons of water1 are needed to supply the grinding mill. Additional water is needed in the flotation circuit as well. With many modern mills operating at2 11,000-165,000 tons/day, water supply volumes can be upwards of 3,000 gpm to 100,000 gpm of flow.For plants operating at or above capacity, disruptions and restrictions in water supply flow can have a direct impact on the production and recovery of the metal. Water supply flow can be limited for a wide variety of reasons but of interest are those limitations that are due to mineral scaling. Mineral scaling is the selective point precipitation of inorganic species above saturation concentrations. Precipitated species form flow-restricting deposits in the mill water system (tanks, pumps, pipe and valves), that will eventually impact water supply to the concentrator."

Jan 1, 2017

By F. Rudloff, C. Karageorgos, J. Moyo, I. Boadi, M. Struble, B. Lumsden

Over it’s more than 100-year history, the Kennecott operation has often been at the forefront of innovation; driven by the demands of the lower grade ore-body and the higher costs of operating in the US where wages are generally higher and regulation more restrictive. One way of reducing operating costs in c/lb is to increase the lbs produced at minimal cost. Despite the relatively coarse grind at Kennecott - about 30% >150μm, approximately 20% of the Cu lost to tail is liberated chalcopyrite in the <20μm fraction, and about 30%-40% in the <37μm fraction. In 2020 Kennecott undertook a detailed plant scale test of the magnetic aggregation technology to increase copper recovery by reducing fine copper losses. A paired statistical plant test of magnetic conditioning on one rougher line showed a 1.12% increase in Cu recovery to 97% statistical confidence. The next challenge, unforeseen at the start of the project, was the fabrication and transportation to site of the equipment for the three remaining rougher rows, during the severe supply-chain constraints of the Covid pandemic in 2021. This resulted in delays and unforeseen costs as world-wide transportation became chaotic, particularly transportation via west coast USA. Nevertheless, the project was completed and commissioned, with only minor delays and cost increases, due to a flexible approach to overcoming the hurdles encountered.

Feb 1, 2023

By Robert J. Brison

The intent of this paper is to try to answer the complex question: "How much grinding capacity should be designed into a new mining - milling project?" Much work has been devoted to the technical aspects of grinding, the "how" of grinding. But, in the writers&apos; opinion, the economically important subject of optimizing grinding capacity in mill design has not received the attention it deserves, at least not in published literature. For the purpose of this paper it is necessary to distinguish clearly between optimizing operation and optimizing design. Optimizing operation involves making the best use of the available plant and equipment. Much excellent work has been done and is being done in this area. In operation, one can make tradeoffs of production rate and recovery, or recovery and grade, to maximize profits. However, this must be done within the limitations imposed in the design stage. Flexibility is limited by the existing plant. In project design, on the other hand., there are no preexisting physical limitations except as imposed by nature itself; the planners and designers have considerable latitude in their efforts to optimize the overall project. They have complete control over a large number of important design variables from the mine to the finished product. The grinding process design is one of these variables. It not only determines the capital cost charges for grinding and the maximum grinding capacity that operating management will have to work with, but also determines the range of capability of the auxiliary equipment, which fixes the degree of flexibility possible in operation. This paper is concerned with optimizing design rather than operation. The terms "optimum" and "optimize" are sometimes used in a technical sense in connection with grinding, recovery or grade. In this paper, these terms are used only in the economic sense. In this age of working large deposits of ever lower grade ores, it is in¬creasingly essential to design projects and plants for optimum economics, based on the most applicable economic. criteria. Since grinding represents a large part of both capital and operating cost of the project, and largely determines percentage recovery of metal, it should be included as one of the factors in optimizing the project design. This paper is written primarily with reference to medium to large copper concentrators employing conventional wet grinding. However, the principles involved should be applicable to other ores and other methods of grinding.

Jan 1, 1972

By K. S. Fraser, R. Frischmuth

High temperature pressure oxidation (>190°C) is a wellrecognized and versatile metallurgical oxidative pre-treatment process commonly used to liberate gold from refractory sulfide ores and concentrates. The pressure oxidation of refractory gold ores was first commercially applied in 1985, at Homestake Mining Company’s McLaughlin mine in the United States. Since that time numerous refractory gold and other high temperature pressure oxidation facilities have been built throughout the world. The design of each facility was met with unique challenges and opportunities which have led to an array of plant configurations, pressure oxidation autoclave sizes, and sulfide oxidation capacities. This paper presents a historical review of high temperature pressure oxidation operations and current projects in execution with a focus on the autoclave vessel design, circuit configuration, and unit sulfide oxidation capacity as a basis for characterization and comparison.

Mar 2, 2022

By John D. Morgan

The United States is the world&apos;s most productive nation and its citizens enjoy one of the highest material standards of living of any people in the world. Materials and energy are the lifeblood of any industrialized economy. Annually the United States uses over 4 billion tons of mineral materials and fuels, or 40,000 pounds per person as detailed in Figure 1. Domestic processed materials of mineral origin and energy are valued at more than $150 billion annually, and they are derived largely from domestic sources, supplemented by imports, as detailed in Figure 2. In recent years the superior productivity of the United States has also enabled it to give food and manufactured articles to many other less fortunate nations and peoples of the earth. What then is our concern with materials at this time? Seeing the burgeoning increases in our mineral demand: from 2 billion tons in 1950, to over 4 billion tons today, and projected to 11 billion tons by 2000 - we are getting questions concerning our ability to continue to increase production sufficiently for the future.

Jan 1, 1974

By Yuting Xue, Alper Kirmaci, Taghi Sherizadeh, Dogukan Guner, Khaled Mohamed

Rib brows present a significant safety hazard in underground coal mines in the United States. To address this issue, researchers at the National Institute for Occupational Safety and Health (NIOSH) and Missouri University of Science and Technology (MST) are developing a practical tool to assess both the potential of rib brow formation and the stability of any formed brows. As part of this effort, a monitoring study was conducted to assess the potential for rib brow formation in coal pillar ribs. This study was conducted in a room-and-pillar coal mine where coal pillar ribs are prone to developing rib brows. Although no rib brows formed in the instrumented pillar, data from monitoring and visual observations provided valuable insights into the loading mechanisms impacting the instrumented pillar. These findings helped identify factors that may reduce rib brow formation, including the cavability of the roof in mined areas, the applied rib support, the strength of rock partings, and the overall integrity of the coal seam. The scientific findings published in the case study aid in assessing the potential of brow formation, offering additional evidence for the need to improve rib control methods in underground coal mines.

Feb 1, 2025

By M. A. Trevits

The National Institute for Occupational Safety and Health (NIOSH), in partnership with the Mine Safety and Health Administration (MSHA), is conducting research to test, evaluate, improve or modify coal mine fire-fighting strategies and methodologies through large-scale tests. Since wood is the second most abundant fuel available during a coal mine fire, it was decided that series of large-scale wood crib fire tests were needed to measure the products of combustion and to observe the capability of commonly available direct application fire suppression equipment, namely, fire extinguishers, water and gas-enhanced foam. This paper discusses the wood crib fire tests, provides insight into the products of combustion and describes observations made during the application of the fire suppression agents.

Jan 1, 2009

By D. Richter

The Pyrometallurgical refining stage of ferronickel manufacturing produces a slag rich in iron and nickel, which is usually further processed for metal recovery. The recovered material is returned to the refining or smelting stages, depending on the amount of impurities. A series of tests was carried out on the Mineração Morro Azul refining slags, aiming at the recovery of the metallic particles through physical processing. Minor changes in the process showed improved results. This paper compares the textures of these slags after being cooled at ambient temperature and granulated under water at high pressure and flow. It concludes that the cooling process is intimately connected to the work index of such slags, thus resulting in direct impact in operating costs.

Jan 1, 2011

By L. E. Bowman

Efficient filtration of fine kaolin particles plays a crucial role in processing of raw kaolin to a marketable product. Oftentimes, filtration Is the rate controlling step of the whole process. As a consequence, plant production is dependent, to a great extent, on the rates being achieved In filtration. In order to alleviate the bottleneck in production, Nalco Chemical Company initiated a reagent development program to chemically enhance the performance of the filtration units. Filler aids of different classes were synthesized for evaluation. These include reagents whose primary mode of functionality were: coagulation, flocculation, thickening, and combinations of the preceding. All reagents that were synthesized and tested were listed under the appropriate Food and Drug Administration sections of the Code of Federal Regulations. This paper discusses the development and application of a new reagent that Improves the filter production rate with minimal Impact on filter solids. The results of laboratory filter studies along with plant data are presented and discussed. Plant data indicate that this reagent is capable of increasing production rates by as much as 35% on various clays of coarse particles to the finest fractions, as well as clays that are calcined. The reagent&apos;s Impact on solids content, re-slurrying characteristics, Brookfield and Hercules viscosity, and drying is within the standards set by plants who have evaluated and now use this product.

Jan 1, 1993

By L. S. Gertsch, M. Z. Abu Bakar

The research presented here is part of a project to quantify the differences in the mechanical excavatability of rocks in dry and water-saturated conditions. A series of full-scale laboratory linear rock cutting tests were carried out with a long-bladed single disc cutter on dry and water-saturated sandstone blocks. The muck collected from the cutting tests was analyzed to establish a link with the specific energy (SE) of the operation. The coarseness index (CI), a non-dimensional parameter, was found to be a useful indicator of the relative efficiency of the cutting operation. An inverse relationship of the form SE = k CI-n was observed between SE and CI. The power n of the relationship for both dry and saturated rock was much lower than found in previous studies. The exponent n is believed to be dependent on the strength of the rock and the cutter type used. Although the average CI was lower for saturated rock than for dry rock, at the same time, saturated rock cutting was found to be less energy-intensive (in terms of SE) than dry rock cutting. Moderate correlation exists between the production rate or yield and the SE of the cutting operation for both dry and saturated rock, which can provide some useful information about the field production rate, discounting the effect of discontinuities in the rock mass.

Jan 1, 2012

By T. Emery, D. Sweet, J. Bourgeois, B. Seymour, D. Porter

Cemented rockfill (CRF) is being used to backfill primary and secondary stopes at the Eagle Mine, an underground nickel and copper mine operated by Lundin Mining. National Institute for Occupational Safety and Health (NIOSH) researchers from the Spokane Mining Research Division (SMRD) are conducting cooperative research with the mine staff to determine if the size of a CRF sample affects its measured strength properties. Based on previous research by NIOSH, cylindrical samples of CRF ranging in size from six to eighteen inches in diameter were cast at the mine and cured underground. The samples were later transported to the SMRD laboratory and the Michigan Technological University where tests were conducted to determine the strength and elastic properties of the CRF. To further analyze the relationship between backfill density and compressive strength, different ASTM International compaction techniques were used to cast the samples. For comparison, tests were also conducted on in-situ core samples that were drilled from a stope which had been backfilled with the same CRF mix. The data collected from this study not only improves our understanding of CRF in-situ properties but also helps optimize Quality Assurance/Quality Control (QA/QC) methods for backfill preparation and testing.

Feb 1, 2023