Search Documents

By J. Brune

The need for reliable and adaptable underground mine communications has become a focal point for both the safety and logistics of a mining operation. New mine communication technology aims to connect personnel, equipment, and data together while setting up a network that can be utilized during normal operations and also in an emergency event. The Mine Improvement and New Emergency Response Act of 2006 (also known as the MINER Act) requires mine operators to establish post-accident, two-way communication between underground and surface personnel and electronic tracking for all mine personnel. Communications systems must be designed such that they can survive major mine accidents, including explosions, fires, inundations and ground falls. Typical, wire-bound communication technologies are vulnerable because wires are often destroyed in such accidents. Wireless technologies that work well on the surface, such as cellular telephone networks; have limited applicability underground because the wireless signals do not propagate through rock.

Feb 23, 2014

By C. W. Newcom

The mining industry continues to be under expanded scrutiny in the health and safety arena, both from federal regulators and the media. While this paper will briefly discuss how enforcement activity, both with citations issued and the size of penalties proposed, the primary focus will be practical suggestions to deal with some key, high-risk areas for a mine operator which could have substantial impact, both in terms of liability and mine operations. It goes without saying that all mine operators need to continue compliance programs they have in place with careful ongoing evaluation of those plans for areas of improvement. The focus here will not be compliance as such, but rather steps to take and procedures to have in place to try to minimize risks in the face of the potential for more significant liability. Thus, our focus will be procedures to respond to unwarrantable failure citations, immediately reportable accidents, and to deal with potential pattern of violation issues.1

Jan 1, 2011

By S. Mojeddifar, N. Ostadmahdi Aragh, M. Hemmati Chegeni

This work integrated selective principal component analysis (SPCA) with a singularity fractal model to map hydrothermal alterations of argillic, phyllic, and propylitic in the north-west of Kerman city in Iran. SPCA results were provided for short wave infrared (SWIR) bands of the Advanced Spaceborne Thermal Emission and Reflection Radiometer (ASTER) sensor tomap phyllic and propylitic alterations. Also, the bands 5–7 were applied to map the argillic alteration zone. SPCA results could present useful information for alteration mapping but it does not show the purest pixels of alteration. Therefore, a fractal model of singularity was applied to highlight the different alteration pixels in the Kerman Cenozoic magmatic arc (KCMA). Thus, the singularity index of different hydrothermal alteration zones was produced. Comparing the obtained results with the field data showed that Kader, Serenu,Meiduk, and Abdar deposits were acceptably identified by alteration mapping. Also, it seems that the singularity index could not discriminate the hydrothermal alterations of argillic and phyllic. The same spectral signature of kaolinite and muscovite minerals is the main reason for misclassifications.

Jul 20, 2020

By Dennis C. Parker

The Porters Creek clay is mined for its absorbent properties. The formation is part of the Upper Mississippi embayment and is recognized in Alabama, Mississippi, Tennessee, Kentucky, Illinois, and southeast Missouri. Major minerals in order of abundance are Montmorillonite, Quartz, Illite, Kaolinite, and Chlorite. Mining consists of open pit operation utilizing track loaders or scraper. The clay is dried or hardened in rotary kilns and crushed to size by roll crushers. The clay granules are sized and air classified prior to storage for shipment or packaging. Granules are sold for pet absorbents, oil absorbents, anti-skid material, fertilizer, and pesticide carriers.

Jan 1, 1979

By Earle Bagley

In late 1971, the Sun Company, then known as Sun Oil Company, acquired a large surface mineable federal coal lease with the thought that those coal measures within its boundaries would provide a future feedstock of either coal or coal liquification. Our Cordero lease was one of the last Federal coal leases let before the recent decade long leasing moratorium. Because of the tremendous demand for compliance steam coal for the electric power industry, a decision was made to develop the property to serve that market. In 1974, Sunoco Energy Development Company (SUNEDCO), the non- oil and gas energy unit of the Sun Company, began engineering studies for development of the lease. The mine was originally designed at a 12.0 million ton per year capacity. The Cordero Mining Company was formed to mine and operate the property. Construction of the facilities adjacent to the lease began in January 1975. Due to the Sierra Club versus Department of Interior Secretary L. B. Morton suit, work within the lease was delayed until mid-1976 when pre-stripping of the overburden began.

Jan 1, 1982

By Verya Nasri, Mehdi Bakhshi

"Fiber reinforcement has emerged as an alternative to steel bars in precast concrete segments due to advantages such as saving cost and reducing production time while developing a more robust product with improved handling and long-term durability. ACI recently drafted a new report as the first design guideline on FRC tunnel segments to provide specific guidance for this emerging technology. ACI document offers general information on the history of FRC precast segments from tunneling projects throughout the world; a procedure for structural analysis and design based on governing load cases, and a description of the material parameters, tests and analyses required to complete the design. This paper summarizes the design considerations in this ACI guideline prepared by the authors of this paper as the main contributors. Application of this guideline to design of a tunnel with an internal diameter of 5.5 m (18 ft) results in elimination of steel bars.INTRODUCTIONPrecast concrete segments are installed to support the tunnel excavation behind the Tunnel Boring Machine (TBM) in soft ground and weak rock applications. The TBM advances by thrusting off the completed rings of precast concrete segments that provide both the initial and final ground support as part of a one-pass lining system. These segments are typically designed to resist the permanent loads from the ground and groundwater as well as the temporary loads from production, transportation and construction. Tunnel segments are generally reinforced to resist the tensile stresses at both the Serviceability (SLS) and the Ultimate Limit States (ULS). With traditional rebar, a significant amount of labor is needed to assemble the cages and place the rebar, which results in higher production costs.Fiber Reinforced Concrete (FRC) can be used to enhance the production, handling, and placement of precast concrete segments. This is because of the uniform dispersion of fibers throughout the segment to include the concrete cover, which is very advantageous for resisting the bursting and spalling stresses. These stresses develop as a result of the high loads induced on the segments during the TBM jacking process. The presence of fiber in the concrete matrix helps mitigate against unintentional impact loads during segment handling and tunnel construction operations."

Jan 1, 2016

By Ronald R. Hartman

I can recall a time 10 or 12 years ago when I spent a pleasant Sunday afternoon driving to Jim Thorpe, Pennsylvania to see a carnotite deposit that had recently been discovered. The announcement of the discovery stated that it was in the Pottsville conglomerate in a road cut along the highway. To my surprise, the highway was lined with cars and every weekend prospector for 100 miles had come to see the ?big uranium deposit of the east?. I literally had to stand in line to make a measurement with the scintillation counter I had with me. The thought at first occurred to me that this is evidence of how thoroughly the surface of the United States must have been prospected, more likely, perhaps it points out quite the opposite. A lot of time and energy was being spent in tracing the footsteps of others and a lot of time was spent looking for the obvious occurrences. The point is, that in the early days a tremendous amount of uranium exploration was carried out but few systematic surveys were made. Thorium anomalies were usually discounted after cursory surface field checks. Conversely, in airborne surveys - anomalies due to elevation changes or thin over- burden on hilltops were often investigated more thoroughly than smaller indications on hillsides and valleys. An adequate supply of uranium was nevertheless found due to the ingenuity and persistence of the geological profession and the public in general. This ?adequate? supply, like so many estimates for raw materials turned out to be far too low.

Jan 1, 1967

By C. C. Clark, D. J. Benton, J. B. Seymour, L. A. Martin

"The U.S. National Institute for Occupational Safety and Health (NIOSH) is conducting research on jackleg use and related accidents in underground metal mines. This paper provides an analysis and overview of jackleg drill usage, accidents, operational characteristics and alternatives, based on information from injury reports, legacy research, stakeholder input and published literature. The results indicate that jackleg drills are involved in more groundfall accidents in underground metal mines than any other drill, and jackleg-drill-related injuries are most prevalent at the face in the course of installing initial ground support. Practical mechanized alternatives to jackleg drills for drilling and bolting under incomplete support in narrow underground openings have not yet been realized. Small, versatile mechanized bolting equipment needs to be developed to address jackleg-drill-related accidents and improve safety at mines where jackleg drills are being used. IntroductionJackleg drill is a generic name for a handheld, rotary, percussion rock drill equipped with an attached reaction leg to provide stability and thrust (Fig. 1). All of the drill and leg controls are located near the operator’s handle at the rear of the head portion of the drill. Jackleg drills are classified according to the bore size of their pneumatic pistons, which normally range from 6.03 to 8.26 cm (2.375 to 3.25 in.) (Kurt, 1982; Clark, 2012). Jackleg drills typically weigh 46.7 kg (103 lb), but the weight can approach 54.4 kg (120 lb) after being fitted for operation with drill steel and air and water hoses (McKibbin and Clark, 2001). In underground mines, jackleg drills are commonly used to drill 3.8-cm (1.5-in.) diameter holes up to 1.83 m (6 ft) deep in rock."

Aug 1, 2016

By P. Rosario

During the last few years high-tonnage plants have been designed with comminution circuits using semiautogenous grinding (SAG) mills, high pressure grinding rolls (HPGR), or both, followed by ball mills in different configurations. A strong interest in improved energy efficiency and reduction of carbon footprint, along with the recent launch of new high-capacity crushers and stirred grinding mills, has driven the industry to investigate the development of novel flowsheets. This paper presents work based on recent projects that include modeling and simulation of two innovative circuits recently considered for current projects. One circuit uses autogenous (AG) mills and parallel trains of crusher-HPGR and the other is a modified three-stage crushing circuit with the use of HPGRs and pebble mills. The paper indicates the potential savings in operating costs provided by the HPGR-pebble mill circuit when compared to a more conventional SAG-mill-based circuit.

Jan 1, 2010

During a period of six months in FY2018, a series of trials were conducted to compare drilling accuracy using two different methodologies and the subsequent impact this had on ore dilution. Testing was conducted at Cracow underground gold mine in Queensland, Australia. The drill rig’s existing alignment process was compared to a new technology system with the following observations: - Using the existing alignment process only 20% of holes surveyed recorded toe points within the +/-300mm (11.8in) tolerance blast-hole deviation. - The new technology was proven to limit rig alignment error, reducing average blast-hole deviation and increasing the number of holes drilled within tolerance by 160%. The increased accuracy reduced stope dilution by reducing over-break of subgrade ore: - Stopes drilled using the new technology recorded 62.6% less average dilution. - This contributed to an overall reduction in dilution for the full year (FY18) of 5 percentage points compared to FY17 - from 22% to 17% (a net decrease of 22.7%). A cost-benefit analysis extrapolated from the trials stipulates that if the new technology were in use for a full 12 months, when applied to FY17 full year data, a 10 percentage point reduction in dilution would represent a net 45.4% decrease, and would result in AUD8.2M (USD5.9) additional ore recovered, with AUD4.5M (USD3.2M) less spent on wasted cost of haulage and processing of diluted ore. As a result, return per tonne would increase 22%, from AUD87 (USD63) to AUD106 (USD77.1). INTRODUCTION Dilution – planned and unplanned – remains a significant cost impairment in the mining process. A series of trials were held over a six-month period in FY18 which established the cost-benefit of new technology as it applies to the alignment accuracy of production drilling rigs in underground mining, thus confirming its ability to limit drilling as one of the causes of dilution. The trials identified three underlying factors affecting drilling accuracy, measurable by blast-hole deviation surveys of planned vs actual toe data. These were; rig alignment error, collar location change/error, and in-hole deviation. The trials involved a comparison of existing rig setup processes and technology, with the new technology (Minnovare’s Production Optimiser system). The trials were undertaken in the same environment; an operating underground gold mine - Cracow Gold Mine. The comparison first revealed the extent to which rig alignment impacts blast-hole deviation. Secondly, the new technology was proven to limit rig alignment error, thereby reducing average blast-hole deviation and increasing the number of holes drilled within tolerance by 160%.

Jan 1, 2019

By John Dodd

Corrosion studies in laboratory ball mills and grinding environment simulations produce corrosion rates and total metal removal rates much lower than those recorded in operating production ball mills. The corrosion component of ball metal loss in commercial mills represents less than 10% of the total loss expressed as micrometers/hour of exposure in recent USBM tests. Such small absolute losses are consistent with ball metal loss measured in production ball mill marked ball wear tests to determine effects of corrosion and abrasion resisting properties of alloys in operating mills which indicate that metal hardness and microstructure determine relative metal loss rates of a given situation. The combination of ore characteristics and grinding process dynamics determine metal loss severity. Alloying for corrosion resistance and modification of the milling corrosion environment yield relatively small metal loss reductions. Alloying and heat treatment to produce high hardness and microstructures of high carbon martensite and for cast irons, M7C3 carbides produces the lowest metal losses in typical wet grinding applications.

Jan 1, 1984

By L. Yuan, J. H. Rowland

"In 1995 and 2003, the U.S. Mine Safety and Health Administration (MSHA) conducted surveys to determine the number of atmospheric monitoring systems (AMS) that were being used in underground coal mines in the United States. The survey reports gave data for the different AMS manufacturers, the different types of equipment monitored, and the different types of gas sensors and their locations. Since the last survey in 2003, MSHA has changed the regulation requirements for early fire detection along belt haulage entries. As of Dec. 31, 2009, point-type heat sensors are prohibited for use for an early fire detection system. Instead, carbon monoxide (CO) sensors are now required. This report presents results from a new survey and examines how the regulation changes have had an impact on the use of CO sensors in underground coal mines in the United States. The locations and parameters monitored by AMS and CO systems are also discussed.IntroductionThe last survey conducted by the U.S. Mine Safety and Health Administration (MSHA) on atmospheric monitoring systems used in underground coal mines in the United States was in 2003 (Francart, 2005). A total of 146 active mines were surveyed. The survey report states that since 1995 there had been a steady increase in the use of atmospheric monitoring systems in underground coal mines as the technology of carbon monoxide (CO) sensors was improved by manufacturers. Atmospheric monitoring systems had become more reliable, and some CO sensors could be purchased with the capability to discriminate between the CO produced by a fire versus CO produced by diesel equipment. This increase in reliability had reduced the number of false alarms and the response time. The faster response time to a developing fire allowed miners to take the necessary action to put out the fire or exit the mine.At the time of the last MSHA survey, some mines still used point-type heat sensors to detect the presence of a fire on conveyor belts. This detection method works by measuring the temperature of the air around the sensor. As a fire starts to develop, smoke and hot gases are produced from the combustion process, and the air is heated up. Once the air and gases reach a designated temperature detected by the point-type heat sensor, a fire alarm signal is generated. Studies have shown that the response times for detecting the presence of a fire using CO sensors are much shorter than when using point-type heat sensors (Conti and Litton, 1995)."

Jan 2, 2018

Copper cathode and Uranium Oxide production at WMC (Olympic Dam Corporation) Pty. Ltd. involves processing leach liquors through a copper solvent extraction plant followed by a uranium solvent extraction plant. This paper discusses the processing problems, metallurgical testwork and circuit changes made due to contamination of amine in the oxime circuit and vice versa.

Jan 1, 1996

By Jacob Carr, Rebecca Knuth, Emily J. Haas, Marvin Cheng, Bob Bissonette

Many industries, including mining, are experiencing an increase in the use of robotic and other artificial intelligence (AI) systems to improve efficiency, productivity and precision. For example, a 2023 survey showed that mining industry executives wanted to integrate more autonomous equipment to improve productivity and alleviate workforce shortages (Haas, 2024). This feedback was coupled with an increased appetite to advance the types and uses of automation and AI in the workplace. However, there is also an increasing concern about the ways that robotic applications may unintentionally affect worker safety. Humanmachine interaction poses potential risks, especially when industrial robots operate near workers in specific environments (such as drilling, handling and transporting materials, equipment inspection and lifting heavy loads). Research has explored the unintended consequences of introducing new technologies or processes in the workplace to include incidents such as being struck by equipment and challenges around data privacy (Lööw et al., 2019; Khurram et al., 2025; Haas and DuCarme, 2015; Almeaibed et al., 2021; Zio and Miqueles, 2024). More recently, the use of digital twin technologies and simulations (hereafter referred to as digital twin systems) has been boasted as a tool that can help prevent unintended consequences around worker safety by identifying and mitigating risks before a worker completes a task in tandem with a robot or other new technology. Digital twin systems produce a virtual replica of a physical environment or process (Almeaibed et al., 2021; Zio and Miqueles, 2024; Saes, 2024). To this end, this article explores the potential role of digital twin systems in enhancing safety within mining and other similar environments. It will primarily focus on environments where robots and human workers may interact, although digital twin systems can be useful with other technology applications. First, we define digital twins and digital simulation as components of a system. Then, we highlight possible applications of digital twin systems in mining to replicate real-world processes, followed by potential benefits of their use and where more research may be needed.

Oct 1, 2025

By Bo Kyung Sim, Dae Young Kim, Jae Won Lee, Ebrahim Farrokh

"The contract C931 of the downtown line 3 (DTL3) mass rapid transit system of Singapore includes half a kilometer twin tunnels running between Mattar and Macpherson stations. An EPB TBM of 6.6 m diameter was used to excavate both of these tunnels. The tunnels pass predominantly through a very stiff silty/clayey fine to coarse sand from the Old Alluvium Formation. In this paper, TBM selection procedure, TBM performance evaluation, and some of the tunneling operation challenges with the TBM in the Old Alluvium Formation are discussed. In this regard, soil conditioning trial tests were performed to resolve the clogging issue and low TBM performance. Thorough TBM operational data analysis was performed to detect high soil abrasivity, backfill grout leakage, and foam nozzle clogging. The results of some of the applied modifications are also discussed to show their effects on the TBM performance improvement. Finally, some of the challenging TBM design specifications are also discussed. INTRODUCTION Tunneling and underground construction in Singapore has been increased in the last 30 years due to the demand for public transportation systems and the limited space above the ground for the infrastructure development. Downtown Line Stage 3 (DTL3) Mass Rapid Transit (MRT) system has 21 km total route length and consists of 16 stations. DTL3 Contract C931 runs between Mattar station and MacPherson station. The construction works in this contract include twin bored tunnels of 6.6 m diameter and 450 m length and a TBM launch shaft of nearly 30 m depth. The tunnels run in urban area below Kallang Paya Lebar Expressway tunnel (KPE), Kallang River Canal, and Circuit Link. Figure 1 shows the alignment of the tunnels in between two subway stations. The tunnels were excavated by an earth pressure balance (EPB) tunnel boring machine (TBM) through the Old Alluvium (OA) formation, a challenging geological formation in the sense of its abrasivity and stiffness. The Old Alluvium Formation mostly includes stiff to very stiff clayey and silty sand. The soil is un-weathered cemented to semi-cemented dense, mainly with a low permeability coefficient of 10-7 m/s and high SPT values (almost 100). The soil is classified as “very high abrasive” according to NTNU SAT test classification (SAT value of 15 to 42). The construction of the first tunnel drive was slowed down due to a number of factors related to soil conditioning and TBM operation. In this regard, a thorough analysis of the TBM operational parameters from the excavated sections was performed to identify the problems in time to prevent unwanted construction delays in the subsequent sections. In the following sections, a brief overview of the criteria used for TBM selection is presented at first. Then, the results from the analyses and tests performed to assess soil conditioning, grout leakage, and soil abrasion are presented. The last section discusses some of the tunneling design features that challenged the TBM operation in this project."

Jan 1, 2016

By Richard Campbell, MEHMET KIZIL, Ismet Canbulat, Serkan Saydam

The design and effectiveness of ground consolidation to regain stability of longwall faces vary widely and are often based predominantly on-site precedence or what were considered successful applications at other sites in similar situations. Little is known regarding product migration characteristics or change in rockmass conditions as a result of the application of consolidation chemicals. This paper presents the in-situ testing rationale designed and implemented recently across several longwall operations in the Bowen Basin, Queensland, Australia to provide quantitative measurement of the actual zone of influence of various resin injection products. Product migra- tion was physically measured by monitoring the change in rockmass temperature as a result of the exothermic chemical reaction of the various strata consolidation chemicals used. In conjunction with strata coring and Lugeon transmissivity testing pre- and post-injection to characterise the improvement in rockmass conditions due to consolidation product injection. The results of the testing programme, migration measurements, and rockmass assessment are presented, along with a discussion on how site- based Rock Mechanics Engineers can incorporate the data into the design of strata consolidation plans.

Jun 25, 2024

By Ray Nivens, Umit Turunc, Caroline Sui, Nick Morrison, Douglas Steiner

"In most copper mines and concentrators, mill water is continuously recovered and reused, with fresh water added to make up for losses. When mixed, these water chemistries can lead to severe scaling, especially in pipes, tanks and pumps on the mill water supply side, reducing flows and causing significant production losses.At KGHM Robinson Nevada Mining Company, increases in the fresh water addition ratios resulted in severe scaling problems and premature pump failures thereby jeopardizing plant production. What initially appeared to be a few isolated scaling events eventually unfolded into a recurring pattern of water supply-related production losses with increasing severity. Through completion of detailed root cause analysis, chemistry modeling, laboratory work, in-plant testing and system engineering, the mechanisms of scaling were identified and addressed.Advancements in fresh water addition practices and antiscalant application methods resulted in a stepwise reduction of the mill water scaling. Cost savings and production benefits were significant to the plant’s financial metrics.IntroductionThe production of mineral and metal concentrates using the flotation process requires large quantities of water. Flotation is utilized as the primary means for beneficiation with sulfide ores. Mined ores are crushed and ground into a slurry of 20-55% solids. For each ton of ore, 400-900 gallons of water1 are needed to supply the grinding mill. Additional water is needed in the flotation circuit as well. With many modern mills operating at2 11,000-165,000 tons/day, water supply volumes can be upwards of 3,000 gpm to 100,000 gpm of flow.For plants operating at or above capacity, disruptions and restrictions in water supply flow can have a direct impact on the production and recovery of the metal. Water supply flow can be limited for a wide variety of reasons but of interest are those limitations that are due to mineral scaling. Mineral scaling is the selective point precipitation of inorganic species above saturation concentrations. Precipitated species form flow-restricting deposits in the mill water system (tanks, pumps, pipe and valves), that will eventually impact water supply to the concentrator."

Jan 1, 2017

"Tell us how you got involved in mining and about your career path.My dad was a coal miner and my uncle was a metallurgist, so when I enrolled at Penn State’s New Kensington Campus, I chose the College of Earth and Mineral Sciences — exact majors didn’t get picked till the end of your sophomore year. Penn State New Ken had an associate degree in mining program and one of the guys in my carpool was going to take Mining 30 in the evening and the other guy (mechanical engineer) was also able to take an evening class. I didn’t want to break up the carpool, so I took Mining 30, complete with essay tests. I could write, so I did well, and the professor said I should go into mining engineering. Fast forward to the end of the next term at University Park, and I realized there wasn’t enough chemistry in mining. Switching to metallurgy would have meant another term at that point, so Dr. Lovell, my advisor, trotted me down the hall and to the next building and said I was a mineral processor. That stuck. I was a summer student at U.S. Steel Research between my junior and senior year and they paid for my master’s degree — all about clay and macerals in coal flotation. During that time, the steel industry tanked, and I thought a Ph.D. would be a good idea — I could always teach at the university level if I had those credentials. The Electric Power Research Institute had a Coal Cleaning Test Facility in Homer City, PA, and I conducted my Ph.D. research on rate and residence time in conventional coal froth flotation cells there and at a local cleaning plant. I went to work at the test facility in 1987 (later CQ Inc.) and stayed there until I started PrepTech Inc. in 1997. PrepTech offers some consulting services for coal cleaning plants and sells mineral processing equipment, mostly to coal companies. I can’t believe it’s been 21 years.And what about your SME career?Of course, I was a student SME member at Penn State. We used many of the SME books in class, so who wouldn’t want the student discount? While in Homer City, I became involved with the Appalachian Plateau Subsection of the Pittsburgh Section. We’d hold quarterly meetings with interesting speakers and had good attendance. I was the secretary. I’m still the secretary and also get the bank statements. We’ll need to close that out some time, but I guess I’ve been hoping for resurgence in the Indiana/Cambria/ Somerset area."

Jan 3, 2018

By Douglas H. Bolton

In recent years, equipment manufacturers have been busy developing remote control systems to catch up with the sophistication and efficiency of continuous miners. Now the tables are turned, and manufacturers are undertaking the new challenge of upgrading, refining and equipping continuous miners to take full advantage of the capabilities made possible by modern, successful remote control systems. Because the operator can safely advance the miner farther without pulling out for roof bolting, continuous miners now need to be equipped with means of complying with correct face ventilation, dust suppression, methane detection, diffusion and improved lighting. Some of the exciting possibilities being developed to catch up with remote control include feedback controls using laser beams as datum points, coal sensing devices with feedback signals to show the operator what the machine is doing, show where it is relative to the coal seam, how hard it is working, and more sophisticated use of cyclic control. Mining machinery manufacturers have accepted the new challenges, and faster, safer mining procedures are already in sight.

Jan 1, 1975

By Yuting Xue, Alper Kirmaci, Taghi Sherizadeh, Dogukan Guner, Khaled Mohamed

Rib brows present a significant safety hazard in underground coal mines in the United States. To address this issue, researchers at the National Institute for Occupational Safety and Health (NIOSH) and Missouri University of Science and Technology (MST) are developing a practical tool to assess both the potential of rib brow formation and the stability of any formed brows. As part of this effort, a monitoring study was conducted to assess the potential for rib brow formation in coal pillar ribs. This study was conducted in a room-and-pillar coal mine where coal pillar ribs are prone to developing rib brows. Although no rib brows formed in the instrumented pillar, data from monitoring and visual observations provided valuable insights into the loading mechanisms impacting the instrumented pillar. These findings helped identify factors that may reduce rib brow formation, including the cavability of the roof in mined areas, the applied rib support, the strength of rock partings, and the overall integrity of the coal seam. The scientific findings published in the case study aid in assessing the potential of brow formation, offering additional evidence for the need to improve rib control methods in underground coal mines.

Feb 1, 2025