Search Documents

By W. H. Schiffbauer

The protection of miners, equipment, and infrastructure is discussed. While the primary focus of the described technology is to prevent miners from being injured, struck-by, or crushed by heavy equipment; another major benefit realized is also the protection of equipment and infrastructure. An attempt is made to define and classify the systems used to provide proximity detection and warnings as well as collision detection and avoidance. Information about the speed of vehicles and human operator response time can be a factor in the choice of what type of system and what features are needed to properly address the needs. How the technology adjusts to compensate for various vehicle speeds, while maintaining the same level of protection is noted. The statistics which justify the need of miner protection are provided. The primary system components required, what attributes they feature, and how they respond in the environment, is briefly highlighted. The physics behind the danger zone marker technology and what makes it so robust and reliable is established. Examples of a few mining applications and specific operational modes are provided for both surface and underground.

Jan 1, 2011

By D. Bradbury

Sufco coal mine, a subsidiary of Arch Western Bituminous Group, recently purchased a reverse osmosis (RO) system. The systems intent was to remove impurities in the water being mixed with the hydraulic oil to maintain the viability of critical longwall hydraulic systems and to prevent degradation. This project not only ensured hydraulic components from corrosion, but also revealed a cost savings by reducing the percentage of hydraulic oil mixed with the RO water. SUFCO WATER TREATMENT HISTORY Sufco coal mine has been in operation for approximately 70 years. Old works extend up to 15 miles one way, not including adjacent mined out longwall panels. Due to the geologic conditions and strata, water treatment has been as simple as putting water in at a high point of a mined out area and recovering it at a low point to discharge. Doing this reduces the total suspended solids (TSS) to less than 25 parts per million (ppm) and the total dissolved solids (TDS) less than 1,200 ppm which complies with Sufco?s water discharge permit. Even though the requirements for the permit were met, the water is still corrosive in nature. A portion of this water is piped back into the fireline (makeup) water system. It is then boosted to pressures of up to 500 psi to support mining sections, belt systems, equipment, fire fighting systems and the longwall.

Jan 1, 2011

By G. E. Viens

The electric arc furnace has characteristics which make it attractive for a number of metallurgical applications. Some of these characteristics are: high thermal efficiency, the possibility of attaining very high temperatures, low off-gas volume compared to fuel-fired furnaces, no impurities are introduced by the heat source, and impurities in only minor amounts are introduced by the electrodes. It also has disadvantages, the chief ones being the relatively high cost of electrical energy compared to fossil-fuel energy and the fact that, when oxide ores are smelted using carbon as reductant, the off-gases emitted are rich in carbon monoxide. As in many other pyrometallurgical processes, fumes and dust are emitted from melting or smelting operations. In many installations, some or all of the off-gases are flared, thereby wasting their energy and contributing to atmospheric pollution. During the last eight years, a shaft-electric furnace has been under development at the Mines Branch, Department of Energy, Mines and Resources, Ottawa, Canada. This project was initiated to try to overcome, or at least minimize, the disadvantages of the electric furnace. Experience on other projects, prior to the beginning of this program, had indicated that preparation of the charge materials, for example by sizing raw ore, sintering concentrates and crushing and sizing the sinter, or agglomerating concentrates into uniform-sized pellets, could make a substantial contribution towards achieving success in arc-furnace smelting projects; This entire

Jan 1, 1971

By Dana A. Echter

The Paso Diablo coal project is located in the Guasare Basin in the northwestern region of Venezuela near the border with Colombia. In 1987, Carbones del Guasare SA, a joint venture comprised of Carbozulia and A.A. Antilles Coal (an Arco and AgipCoal joint venture) was formed to develop the Paso Diablo coal reserves for world markets. Regional drilling has indicated a coal resource of more than 6 Gt (6.6 billion st). Further exploration has delineated the Paso Diablo deposit as an area particularly suited for cost-effective surface mining. The calculated economically minable reserves of this area (200 Mt or 220 million st) and the coal quality characteristics are based on extensive core drilling programs. Initial coal mining operations began in August of 1987 and the mine is presently producing at a rate of 1.5 Mt/a (1.65 million stpy). The coal is hauled about 85 km (53 miles) to a barge loading terminal at Santa Cruz de Mara using highway-type haul trucks. When the coal reaches the terminal, it is loaded into barges and then transloaded onto ocean-going vessels with barge mounted

Jan 1, 1990

By R. Pakalnis

A comprehensive project has been completed at the University of British Columbia that focused on the development of a commercially competitive composite cable bolt. Laboratory evaluation consisted of pull tests, preliminary shear tests, grout column testing and scanning electron microscope evaluation of the composite cable bolt. Field implementation at five underground mines throughout Canada were completed for technical and overall performance evaluation of the new product. The project began in 1989 under the sponsorship of HDRK Ltd., a consortium of mining companies including Inco, Noranda and Falconbridge Ltd. The objective was to develop a cuttable cable bolt that would serve as support for a continuous miner within a hardrock environment (Mah, 1994). The bolt was required to be cuttable by a continuous roadheader without adverse effects to equipment, personnel and the milling process. From the beginning, the focus was to employ existing cable bolt installation technology (Goris et al., 1994) whereby the cable bolts are grouted within a 4.8-cm-diam (1.08-in.diam) or larger employing a portland cement grout having a water:cement ratio between 0.35:1 to 0.4:1.

Jan 1, 1994

It doesn't take any special acumen to note that US engineering and construction firms are busier than ever with mining projects in this mineral conscious world. This special issue of Mining Engineering takes a look at E&C companies-their expanding role, their special capabilities, and their challenges and problems. ME sent a questionnaire to a representative sample of E&C firms. Information was sought about officers, ownership, and amount of business. ME also asked about types of projects and commodities dealt in as well as market distribution and forms of payment. The accomnanying charts show how the 17 responding E&C firms answered these and other questions. Other ME survey questions, and a review of company literature, yielded information about financing techniques and special challenges for E&C firms. Insights were gained concerning government impacts, customer-generated problems, and promising areas for development-including synfuels-in the minerals industry. These areas are discussed later in this article. Accompanying articles in the special issue discuss the E&C company's role in mining projects, research and development in E&C firms, one approach to contract work used by an E&C firm, and an E&C project case study.

Jan 10, 1980

By M. L. Nave, R. E. Melley

DC motor drives are available technology for belt conveyors. The success of the application in mining depends on adequate and timely consideration of DC drive features. The purpose of this paper is to familiarize and inform possible mining users of DC drive attributes.

Jan 1, 1996

By A. Ayoubian, V. Nasri

This Tunnel Connection project will include construction of two short tunnels to connect the existing subway tunnels (Red and Blue lines) in the northern loop area of downtown Chicago through a new station. The Southeast Tunnel will connect the Red Line to the new station below the intersection of State and Washington Streets and the Northwest Tunnel will connect the Blue Line to the new station below the intersection of Dearborn and Randolph Streets. The connection tunnels are located in a very dense urban area of downtown Chicago and under several important historical buildings. Both tunnels are curved at the intersections and located at a depth of about 7.5 m below ground surface in saturated soft clay with an average undrained shear strength of approximately 25 kPa. The design calls for minimizing surface disruption and ground displacement while maintaining normal operation of the existing subways during the construction of the connections tunnels. This paper presents mining and cut and cover tunneling alternatives for the project.

Jan 1, 2007

By J. Cheung, H. Rabia

The traditional methods for predicting mine air temperatures are based on steady state heat transfer models as developed by Voss (1969) and Starfield (1983). These models are useful in providing approximate predictions of air temperatures in trunk and gate roadways. More complex models are required to provide predictions along faces. In practice, the heat flow in underground mines is of transient nature and recent observations in some British Coal mines show temperature variations of up to 5°C during a working week at any one point. In addition, the recent introduction of district recirculation of mine air in British mines requires a more precise prediction of air temperatures during start up of the system or during breakdown. A transient heat transfer theory based on the work of Jordon is presented. The method lends itself easily to computers due to the large number of calculations involved. The proposed transient model is validated using actual temperature data collected in roadways in Wearmouth Colliery in the North East of England. The transient results are compared with the steady state predictions of Voss (1969). Finally, predictions of air temperature in roadways for a recirculation system will be made using both the transient and steady state models. Temperature predictions along faces will be made using a separate model.

Jan 1, 1989

By C. R. Stephan, N. B. Greninger, W. A. Slivensky

The U.S. Bureau of Mines and the U.S. Mine Safety and Health Administration (MSHA) are participating jointly in a research program to evaluate strength characteristics and air-leakage resistance of various proposed seal designs for use in underground coal mines. Over 20 full-scale seals were constructed in the Bureau's experimental mine at the Lake Lynn Laboratory, air-leakage tested, then subjected to pressure pulses of 0.14 MPa or greater. A discussion on the experimental procedure, construction techniques, and the explosion and air-leakage test results is presented. Four types of construction material were used during this seal testing program: solid-concrete-blocks, low-density foam blocks, cementitious foam, and wood blocks. Only one of the solid-concrete block designs using a mortared thick wall survived the explosion and air-leakage tests. Most of the low-density foam block and cementitious foam seal designs were judged to meet the requirements to be considered a coal mine seal. One of the wood block convergence seal designs failed explosion testing. Based, in part, on these research findings, several alternative seal design constructions using low-density foam blocks, cementitious foam, or wood have been approved by MSHA for use in coal mines.

Jan 1, 1993

By Richmond Bennett

Airborne geochemistry became a reality with the advent of a high-sensitivity airborne gamma ray spectrometer with large volume NaI (TI) crystal detectors. Small variations in the concentration of potassium (as K40), thorium (as T1208) and uranium (as B1214) along the flight lines can be determined by measuring the gamma radiation with a sensitive airborne spectrometer. Small volume crystal spectrometers are useful only for detection of major surface uranium (Bi214) variations, but the large crystal volume system is an airborne geochemical exploration method capable of locating hydrothermal mineral deposits. Radioactivity as a guide to ore has been discussed in the literature by Damon (1950), Gross (1952) and others. The theoretical basis is that potassium, thorium, and uranium are concentrated in late stage solutions during magmatic crystallization. Thorium and uranium are concentrated in late stage liquids because their large atomic radius and high ionic charge prevent them from entering into the crystal lattice of common rock-forming minerals (Rankama and Sahama, 1950). Potassium, which has a large ionic radius and small charge, also can be concentrated in the high water content late stage fluids (Heier and Adams, 1964). A large proportion of uranium and thorium in rocks occurs around grain boundaries of the essential rock-forming minerals (Hurley, 1950). Uranium and thorium substitute for zirconium in zircon, a comparatively early forming mineral. However, most of the thorium and uranium is concentrated in residuals where they can be fractionated and incorporated into allanite, monazite, xenotime, and other minerals.

Jan 1, 1970

By J. B. Gwiazda

Maintenance of a constant load setting throughout longwall support units and selection of the proper initial bearing capacity depending on the type of roof strata are the basic factors that ensure good performance of roof support in a longwall. These requirements can only be met by hydraulic support. The greatest advantage of hydraulic support is achieved when uniform pressure is imposed on the roof throughout the length of the longwall. Such support, however, is provided only if each of the support units acts with the same force against the roof, i.e., has the same setting load. In such cases, the roof behaves like a uniform plate without bending and shearing stresses, thereby ensuring an undisturbed structure. Without a positive set value system, achieving an equal setting load for all units of the longwall support is impossible. Due to alterations of the feed line pressure of support units as well as some reasons related to man's psychology, operators extend the height at different setting loads. This produces nonuniform roof stress, and disturbs the structure. Consequently, the roof usually cracks. The author has developed a positive set value system, which is described in this Technical Note. Selection of the setting load Two pressure values in the feed lines are usually applied in longwall hydraulic systems. Lightweight support is fed by 25 MPa (250 bar) liquid, while heavy duty units receive a nominal pressure of 31.5 MPa (315 bar). Such pressure is required not only for the props but also to power the adjust¬ment jacks and the advancing ram. If the feed pressure is too low, there will be difficulty in shifting the unit despite the inversion system of the advancing rams. On the other hand, for many roof types, the feed pressure often appears to be too high when applied as the setting load pressure. An excessive setting load acts too strongly against the roof, crushing weak strata close to the roof. The author has recognized a case where an excessive setting load destroyed not only the nearby roof strata but also the strata above a 2-m (6.6-ft) sandstone layer. In addition, an excessive setting load relieves the side¬walls, increasing the resistance when using cutting machines. As a result, the yield of coarse coal is diminished, and increased fines dominate in the final product, lowering its economic value. As indicated, selection of the proper setting load, depend¬ing on the mining and geological conditions of the extracted seam, is extremely important. In some mines, measures applied to prevent disturbances include reduction of the feed line pressure by adjusting the feed pump valve. The disadvantage accompanying reduced feed line pressure is more difficult operation in advancing the ram. Due to the reduced feed line pressure, the force of the advancing ram is much lower than the designed value. Other designs suggest using a third feed line. However, installation of supplementary valves on the support units is required, a time-consuming and expensive procedure. The disadvantages of the powered supports are eliminated by a system designed by the author. So far, such a method of setting load control has not been used in any type of support. Setting load control unit The designed positive valve set for prop loading and the setting load control correspond to existing control systems for hydraulic powered support. The layout of the unit connected to the hydraulic prop control is presented in Fig. 1. The unit is marked LIDS. It incorporates three valves that may operate separately or connected. Valve A automatically opens and closes with liquid flow in the prop feed circuit. The valve is opened when the canopy touches the roof and closed when the support unit is withdrawn. Valve B serves as the setting load control. Valve C automatically opens and closes the flow in the line connecting the under-piston space of E to the prop F with the separator G. The valve block of each support prop is marked BZ. The UDS unit is connected by the hydraulic lines to the F prop control circuit. A valve is connected by H to pressure line J and by K to the G separator. In the UDS-3 version, line L is connected to M, linking the over-piston space of F prop with the G separator. Valve B is linked with valve A by a connector; it is also connected to the under-piston space E of prop F by line P. Valve C is fixed between lines K and P, connecting space E of prop F with the separator G. When setting the support, the liquid flows from line J through separator G, the BZ valve, and valve C to the space E of prop F. When reaching the roof with the canopy, valve A is opened and C closes. In this way it is impossible for the operator to cause the liquid pressure in space E of prop F to reach the level of line J. The prop pressure is set by valve B of the UDS unit. When withdrawing the support, valve C is automatically opened and A closed. Three UDS units have been fabricated and are designated

Jan 1, 1990

By David A. Brence, Andrew D. Marti, Richard P. Stahura, Ronald J. Valentine

The development of an effective belt-cleaning system for a new conveyor system seemed a fairly conventional assignment. But a closer examination of the project showed a number of “fine print” details: •High altitude location (with resulting cold weather and low humidity conditions). •Long conveyor length. •Troublesome material (very sticky and capable of hardening like concrete). •Limited water. These difficulties are spelled out the challenge of developing a cleaning system for the production conveyor2 (PC2) belt at Climax Molybdenum’s Henderson Mine.

Jan 1, 2005

By D. L. Purcell, B. T. McClure, J. McDonald

The U.S. Bureau of Mines has completed a laboratory evaluation of exhaust emissions from a diesel engine using an oxygenated diesel fuel. The fuels tested were soy methyl esters in a neat (100%) form and low sulfur, petroleum number 2 diesel fuel (D2). The engine tested was a Caterpillar 3304, indirect injection, naturally aspirated, 75 kW, diesel engine that is typical of engines used in underground mining applications. The objective was to determine the extent to which oxygenated fuels, such as methyl esters, reduce diesel particulate matter (DPM), and their influence on upon gaseous emissions such as total hydrocarbons, CO, NOx, NO2, formaldehyde, and other exhaust emissions. Heavy- and light-duty transient tests were used to simulate load cycles typical of mine applications. The soy methyl ester fuel produced greater amounts of volatile DPM (organic material) but much less nonvolatile DPM (carbon soot) for overall DPM reductions. A diesel oxidation catalyst (DOC) typical of the type commonly used in metal and nonmetal mines was tested with both fuels. The DOC further reduced the volatile and total DPM when used with the soy methyl esters, but increased the total DPM for D2 due to sulfate formation. The soy methyl ester fuel reduced CO and hydrocarbon, and NOx emissions. The DOC further reduced CO and hydrocarbon emissions.

Jan 1, 1995

By M. P. Oommen

This paper provides a brief look at a proposed short-longwall for coal, development. The proposed method is an attempt to realize the advantages of longwall mining in deposits that, historically, would only be minable by continuous mining methods. An overview of the proposed layout, development requirements, production rate, ventilation scheme and other associated features is provided. This mining method could help operators in above-drainage seams where minable areas are smaller. It may also have application in areas that are peppered with gas wells and in environmentally sensitive areas which preclude the use of conventional longwalls.

Jan 1, 1993

By Olivier Martin

In busy and historic cities, traditional open box metro stations are becoming outrageously difficult, unacceptable for the citizen and uneconomical. Hybrid stations provide an interesting alternative. In-house experience of Gautrain (South Africa), West bay (Qatar), Cairo line 3A (Egypt), and Melbourne (Australia) all aim to reduce disturbance to the city and its inhabitants during construction. Constructed in rock or in deep soil under water table, they take advantages of the latest construction techniques from cement grouting to freezing, and from traditional excavation of cavern to large tunnels constructed by sophisticated tunnel boring machines (TBM). Today, they form the ultimate construction challenge.

Jun 13, 2021

By H. Reginald Hardy, Maochen Ge

Data analysis is one of the most important steps required for the successful application of the acoustic emission/ microseismic (AE/MS) technique. A dedicated computer software package to analyze acoustic emission/ microseismic data associated with field applications in the geotechnical area has been developed recently at Penn State University. This paper addresses the major features and applications of this computer software package.

Jan 1, 1986

By A. L. Hinde

Ideally, mill circuits should be controlled so that excessive random disturbances are reduced in frequency and amplitude. It is difficult to derive an objective measure of the effectiveness of any chosen control strategy. Often, the response of the circuit to pulse or sinusoidal disturbances is used as a measure of the effectiveness of control, but this is not adequate in many circumstances because such disturbances bear little resemblance to those that occur in practice, and such an approach cannot be easily related to the profitability of the reduction process. A superior approach appears to be the application of the theory of stochastic processes. This theory permits both real process disturbances to be modelled accurately, and useful objective functions for control to be derived. A test of the usefulness of stochastic theory in mill control was made on the gold ore milling circuit shown in Figure 1. This circuit was fed with an ore which had a liberation characteristic such as that shown in Figure 2. It is simple to show that, for such a liberation characteristic, the recovery of valuable mineral will vary as the standard deviation of the particle mass-size distribution varies even though the mean particle mass-size is kept constant. Similarly it may be shown that excessive perturbations in the circulating load in a milling circuit such as that shown in Figure 1 can affect liberation. Figure 3 shows how, as the cyclone feed density increases and the sump water addition decreases at constant sump level, the cyclone operation becomes unstable and the discharge "ropes? with a consequent catastrophic coarsening in product size. By minimising the variance of the circulating load it is possible to reduce the probability of initiating instabilities of this nature.

Jan 1, 1977

By R. E. Gertsch

A mobile-modular carbon adsorption mill design and operation for small to medium sized heap leach precious metal mines is presented. In the mobile-modular strategy, charcoal columns with adsorbed metal move from small strategically located carbon adsorption loading stations to a central stripping facility and back. The design has many advantages: 1) It scales-up from pilot plant to full production. 2) It has low capital requirements. 3) Operational costs are competitive with other systems. 4) Mill production can react quickly to changes in ore grade or property area. 5) The solution circuits are simple and easy to maintain. 6) Charcoal damage is reduced.

Jan 1, 1993

By Searl. Milton F.

Introduction The urgency of further development of our domestic energy resources becomes more apparent every day. The production capability of existing facilities, taken in the aggregate, declines perhaps 10% per year; imported energy is expensive if available at all; conservation helps reduce demand but eventually will reach a point of diminishing return; new energy sources are promising but past experience, as with nuclear power, teaches us lead times are long and success is not assured. To approach the energy future rationally, it is essential to have some idea of the size of the nation's remaining energy resources, their characteristics, and the degree of uncertainty involved in their estimates. Resources are, of course, only one end of a long chain leading to energy supply to the ultimate consumer. They are an essential element, however, and the only one not under society's control. Given that the resources and a national will to produce the energy exist, it is possible to convert the resources to supply in, generally, an environmentally reasonable manner. However, the process of developing supply takes time. Government must permit access to the resource, and remunerative prices and further evolution of technology are required. This paper does not deal with these essentials, but they must not be forgotten. This discussion is limited to coal, oil, natural gas and gas liquids, uranium, and oil shale. Other energy sources are discussed elsewhere in this issue. Crude Oil Conventional crude oil resources are of greatest concern today, given our dependence on imported oil and its rapidly rising price. Estimates of oil originally in place (OOIP) range from 619 billion bbl to 1,094 billion bbl, differing by almost a factor of two (Table 1). This is surprising because the U.S. is a mature petroleum province with over 120 billion bbl produced and over 400 billion bbl OOIP discovered. Differences in the estimates involve differences in the experience of the various estimators, the interpretation of present geologic information and historical statistics, the methodology, and probably the extent (i.e., water depths) for which offshore resources are included. The range shown for the estimate of a given estimator appears to be primarily due to geologic uncertainty. This uncertainty can be measured by taking the ratio of the low and of the high estimate to the expected estimate for that information source. The low estimates range from 0.85 to 0.87 of their respective values. The high estimates range from 1.18 to 1.27 of the expected values. In all cases the high estimate is further from the expected value than the low,

Jan 9, 1980