Search Documents

By R. Kneisley, D. Conover, K. Haramy, K. Hanna

INTRODUCTION Coal mine entry intersections are high-risk areas for roof falls due to inherently wide roof spans, excessive stress, and variable intersection shapes resulting from breakthrough misalignments. Statistics from underground coal mines reveal that a high percentage of injuries occurs from roof and rib falls in entry intersections (Peng, 1980). The U.S. Department of the Interior, Bureau of Mines, is conducting a field research project to investigate failure modes surrounding underground coal mine entry intersections. The research objectives are to (1) develop a method to determine failure modes and stress-displacement relations around coal mine intersections and (2) develop engineering guidelines and empirical relationships for use in designing safer coal mine entry intersections. The basic approach to achieve the objectives is to instrument and monitor intersections before, during, and after intersection development in order to determine contributing parameters, such as in situ stresses, stress changes, strata movement, geology, physical properties, and mining sequence, that may influence the short- and long-term stability of the intersection and adjacent entries. This paper describes a rock mechanics instrumentation program, data analyses, and a comparison of two case studies conducted at two underground mines, designated as "A" and "B", in the Illinois Coal Basin. The instrumentation plans and data collected during development and long-term monitoring of four-way intersections and adjoining entries are presented. Data analyses of pre- and post-mining roof stress, pillar loading, strata movement, roof bolt loading, and geologic features are included. INTERSECTION FAILURE MECHANISM The region surrounding an entry intersection is characterized by different failure criteria than the region surrounding a single entry. Stresses induced during intersection development may result in a high incidence of roof and rib failures. Various numerical modeling techniques have been used to evaluate the failure modes surrounding intersections (Gercek, 1982; Chugh et al., 1975). Numerical modeling techniques include problems associated with the analysis of post-failure behavior, provision for different horizontal stresses (i.e., 01 f 021, and determination of inputs required for any non-elastic behavior. It seems likely that more sophisticated failure criteria, based on actual field data, are needed. The Bureau of Mines has conducted an extensive instrumentation program to investigate actual intersection failure mechanisms and to provide an improved understanding of stresses and deflections using beam and plate theories. Beam theory is not applicable to analyzing intersections (Wright et al., 1964); however, it can be used to explain roof deflection and failure (shear and flexure) of adjacent entries and to provide an improved understanding of stress changes and displacements as the entries, crosscuts, and intersection are developed (Hanna et al., 1985). Beam theory may be used for entries when the roof length is twice the width. When the length is less than twice the width (as in intersections), the roof must be analyzed as a three-dimensional problem, and stress and deflection calculations are based on flat plate theory (Adler and Sun, 1976). The confined-core theory (Wilson, 1972) hypothesizes that within a typical pillar, two regions exist: a confined-core region where the horizontal confining pressure is uniform and approximately equal to the overburden pressure, and a yield zone where the vertical pressure increases from nearly zero at the rib to a pressure peak at the boundary of the yield zone. The strength of coal in the yield zone ranges from nearly zero at the rib to nearly full strength at the confined core. The vertical stress in the confined core decreases from maximum at the yield zone boundary to the overburden pressure some distance into the pillar. Excavation of the adjoining entries

Jan 1, 1986

By Emily Wortman-Wunder

As the 2013 president of the Society for Mining, Metallurgy and Exploration, Inc., I am pleased to present the 2013 issue of the Transactions of the Society for Mining, Metallurgy and Exploration, Vol. 334. The timely publication of professional papers that promote the advancement of scientific and technical knowledge is critical for enabling technology transfer. SME plays a key role in this process through its publications. Communication within the mining community is the key to a successful profession and society. This technology exchange continues a tradition that dates back to the 1871 meeting of 22 mining engineers in Wilkes-Barre, PA, that resulted in the founding of AIME; those individuals envisioned that these transaction volumes “would form a most valuable and greatly needed addition to our professional literature.” This volume fulfills that pledge. The 2013 Transactions contains 73 papers covering most every aspect of the mining life cycle and encompassing the diverse sectors of our industry including coal, industrial minerals, metals, health and safety and computational methods. It includes all 18 papers published in 2013 in the Technical Papers Section of Mining Engineering magazine (Vol. 65) and all 33 papers published in 2013 in Minerals & Metallurgical Processing (Vol. 30). Additionally, this volume contains 22 papers that are being published for the first time in this issue. The papers presented in this volume were written by some of the most distinguished professionals in the industry worldwide. Some of the many research highlights from 2013 include discussions of perennial issues, such as how to adequately prepare the next generation of mining engineering students for the workforce (Frimpong et al., pp. 44-52) and how to predict and prevent coal mine bursts and bumps (Pariseau, pp. 60-68), the highly anticipated February Rare Earths issue of Minerals & Metallurgical Processing, and papers analyzing electrical injuries in the U.S. Mining industry (Homce and Cawley, p. 367-375) the latest in assessing the safety and efficiency of operations. All 73 technical papers were peer-reviewed. The process of review and publication requires much hard work by authors, reviewers and our publications staff. As the 2013 president of SME and on behalf of all our members, I would like to extend our gratitude to all whose volunteer efforts contributed to the publication of this volume.

Jan 1, 2013

By B. M. Eiter

The impact of fatigue is seen not only in its effect on the job performance of haul truck operators but also on the health of the operator and the productivity at the mine site. Its impact can even extend outside of the mine site to the health and well-being of the surrounding community (Fourie et al., 2010). In this paper, a case study of a small, surface mining organization is presented. The goal is to highlight the fatigue risk management system implemented at the studied mine site. Mine safety personnel who were interviewed discuss the changes made to the infrastructure of the mine, to administrative areas such as the number of shifts and the use of vacation time, as well as the implementation of new technology into haulage vehicles. This paper reviews how these changes are supported in the research literature.

By M. R. Shahan, W. R. Reed, J. P. Rider

Roof bolter operators may be exposed to high respirable dust concentrations on continuous miner sections with blowing face ventilation when bolting is performed downwind of the continuous miner. One solution to reduce the high respirable dust concentrations is to use a canopy air curtain (CAC) to deliver clean air from a filtered blower fan directly to the bolter operators under the canopies. The influence of CAC installation in the airflow and dust dispersion around the location of the roof bolter operator can be evaluated by using computational fluid dynamics (CFD). This study, performed by the National Institute for Occupational Safety and Health (NIOSH), considers two scenarios: (1) a roof bolting machine in the center of the entry for installation of the fifth row of bolts from the face, and (2) a roof bolting machine positioned close to the face for the installation of the last row of bolts. In both scenarios, the bolting machine is placed in an environment which contains 6.0 mg/m3 of respirable dust and is ventilated by a blowing curtain with 3000 cfm (1.42 m3 /s) of air. This environment is used to simulate the roof bolter machine operating downstream of a continuous mining machine. Two operation positions are simulated at the same bolting location: dual drill heads in the inward position for two inside bolts and dual drill heads in the outward position for two outside bolts. The influence of the CAC on airflows and dust dispersion is evaluated with the CAC operating at 250 cfm (0.12 m3 /s).

By A. Cecala, J. Noll, J. Hummer

The National Institute for Occupational Safety and Health has observed that many control rooms and operator compartments in the U.S. mining industry do not have filtration systems capable of maintaining low dust concentrations in these areas. In this study at a mineral processing plant, to reduce respirable dust concentrations in a control room that had no cleaning system for intake air, a filtration and pressurization system originally designed for enclosed cabs was modified and installed. This system was composed of two filtering units: one to filter outside air and one to filter and recirculate the air inside the control room. Eighty-seven percent of submicrometer particles were reduced by the system under static conditions. This means that greater than 87 percent of respirable dust particles should be reduced as the particle-size distribution of respirable dust particles is greater than that of submicrometer particles, and filtration systems usually are more efficient in capturing the larger particles. A positive pressure near 0.02 inches of water gauge was produced, which is an important component of an effective system and minimizes the entry of particles, such as dust, into the room. The intake airflow was around 118 cfm, greater than the airflow suggested by the American Society of Heating, Refrigerating, and Air-Conditioning Engineers (ASHRAE) for acceptable indoor air quality. After one year, the loading of the filter caused the airflow to decrease to 80 cfm, which still produces acceptable indoor air quality. Due to the loading of the filters, the reduction efficiency for submicrometer particles under static conditions increased to 94 percent from 87 percent.

Jan 1, 2015

By L. B. Phelps

This paper focuses on the use of an integrated mine planing software package entitled "REMINE" which was constructed to provide a project evaluation tool for analysis of remining projects. Coal remining constitutes the affecting of sites which have had a past history of mining and have a pre-existing pollutional discharge. Such sites require a Best Professional Judgement (BPJ) analysis. The program was written to provide such an analysis with flexibility in the mine plans which can be analyzed. The process required for a BPJ analysis will be detailed and mine plan simulation performed to demonstrate the analysis.

Jan 1, 1990

By Richard Kojo Gabah

Western mining companies are entering an African critical minerals market where access is harder to secure, risk is being priced more sharply, and execution advantages are increasingly decisive. The continent holds significant reserves and production potential of cobalt, lithium, copper, graphite, manganese and rare earths critical to the energy transition, yet Chinese-aligned capital has built a structural edge in access and execution speed. Simply signing narrow offtake agreements to buy output is no longer sufficient. Western firms win when they convert quality orebodies into bankable projects by reducing aboveground risk faster than competitors through integrated infrastructure access, durable fiscal alignment, and credible local value creation. Western mining companies will break into Africa by pairing capital with partnership, building corridors enabling infrastructure and power, designing credible value addition pathways and operating in a way that is politically durable through transparency, community benefit and fiscal terms that share upside in commodity upcycles. This feature article offers a practical playbook for mining executives and investors. The core argument is straightforward. Winning in Africa requires competing on the full system around the mine. Corridors and power, processing pathways, contract durability, community benefit and regulatory execution are now decisive variables in project valuation and capital access.

Mar 1, 2026

By R. L. Grayson, S. S. Eslambolchi

"In making strategic economic decisions, it is important for a mining company to gain insights on the impact of significant political, social and economic issues when planning for present and future mines. The size of any mine, measured by the average number of employees working in the mine, will likely vary according to the pressures generated by the significant issues from one year to another. The objective of this study is to develop a model that represents U.S. underground coal mine size transitions during the period 2002-2012 using data derived from the MSHA databases. Coupled with information on significant issues over the past ten years, this model is used to gain insight on the impact of the issues on mine sizes. Results indicate that the structural impact of the combined driving pressures can be discerned by examining the year-to-year stability of mine-size categories. The effects of The MINER Act, the Obama Administration environmental policies on coal, and the coal market are evident. The lessons learned from these analyses give good insights on what the industry and market responses have been on the structure of the underground coal industry over the period of study. INTRODUCTION It is apparent that key driving issues affect the structure and viability of the coal industry. The driving issues may be political, social, and/or economic in the final analysis, but are generally rooted in reaction to dramatic and publicized events or movements. Mine disasters, an increase in miners’ disease prevalence, strife in the coal fields, and negative environmental impacts on air, land or water can capture the attention of the media and the public. Some of the issues occur over a long period of time, like the current global climate change movement. The coal industry veteran can sense the changes in political and social sentiment, and attempt to react to the economic repercussions; however, the insights from the media and from unique combinations of driving pressures are difficult to fathom. Thus decisions made on inadequate information related to the driving pressures and their likely impacts could lead to missteps in corporate and market restructuring. One way to gain some more insight on the potential impacts is to examine the complicated restructuring of mine operations in reaction to the driving pressures of the recent past. This paper examines an 11-year history of the changes in the underground coal industry structure, as reflected by changes in the numbers of mines in various statuses by mine-size categories. Superimposed on the results of mine-size changes is a mapping of the key driving pressures that occurred over the same period, 2002-2012. It is assumed that using this methodology, some important insights can be gained on the immediate and delayed responses to the driving pressures during that period."

Jan 1, 2015

By Barbara J. Arnold

The Electric Power Research Institute (EPRI) and six EPRI-member utilities are sponsoring research to define relationships between coal properties and coal handling behavior. Deratings and outages caused by plugged chutes or bunkers or frozen coal can cost utilities millions of dollars annually in lost energy production as well as in manpower to restore coal flow. There is also the added expense of maintaining redundant equipment to assure a continuous coal feed to the boiler, a common practice for utilities. Over the past two years, researchers at CQ Inc. and Iowa state university have collected and analyzed coal samples to develop a coal handleability index for utilities to use when specifying coals for their power plants. These coal samples cover ranges in ash content, rank, grindability, size distribution, and moisture content--properties that affect the handling behavior of coals. Other properties, such as the washability and ash composition, are measured as well. Over the remaining two years of the project, all of these analyses will be correlated to handling behavior, measured using a triaxial shear tester that determines the strength of a coal under compression. An index will be developed and validated at host utility power plants.

Jan 1, 1991

By Martial P. Corriveau

The preparation of coal is essentially the same for export as it is for the domestic market. The big difference, I would say, is that, while coal for certain domestic uses (utilities, for instance) need not always be of the highest quality, as long as it is uniform, the buyer of coal for export invariably demands a well-prepared, top-quality product. And he is willing to pay for it, as long as he knows what he is buying. This is where quality control enters the picture. The day is long past since the export market was the dumping ground for coals which could not be sold on the domestic market. Today, the export buyer wants American coals not so much for a price but for the necessity of blending the American coals with foreign coals to achieve the desired chemical and/or physical characteristics, To blend intelligently, he must know in detail what are the qualities of the coals to be blended. Sampling and chemical analysis facilities at the piers provide the information on the coals exported, These facilities are maintained for the export buyer by independent laboratories; however, in one instance, the buyer operates his own laboratory. With very few exceptions, and Clinchfield?s Moss No. 3 mid-volatile coal is one, cargoes shipped overseas are loaded as blends of two or more coals. Up to now, foreign requirements have not been too clearly defined; therefore, shippers must be prepared to blend mixtures of the desired combination. Successful blending requires an accurate knowledge of the coals shipped. And this makes it necessary for the coal producer to maintain his own control laboratory.

Jan 1, 1959

By J. B. Malcolm

The discovery of tungsten-bearing quartz outcroppings in Vance County, N. C., by the Hamme brothers in 1942, made international news in the mining industry and was, in fact, one of the major ore discoveries made in the U.S. during the last 25 years. Operations began at the Hamme mine in 1942, but after 16 years of successful operation, the mine was closed down in 1958 under adverse market conditions. By that time, it had produced nearly 20 million lbs of metallic tungsten. Because of the square-set timber mining method then in use, mine operating expenses were high, actually representing 78% of the total operating expenses at the property. In timber work alone, 160 men were employed. Approximately 500,000 bd ft of timber were placed monthly at a direct supply cost of $1.00 per ton of ore mined. Late in 1959, following a slightly improved position in the tungsten market, company management decided that, by changing the mining method, the operation could be economically feasible. The major premise in this decision was that a reduction of from 25 to 30% of the mining costs could be achieved by the conversion of the mining method from square-sets to horizontal cut and fill. Reopening of the mine began in February 1960, Full production has now been reached and overall mine productivity has been doubled.

Jan 1, 1962

By Joe D. Allison, Tom D. Baugh

The analysis for total cyanides (CN, or the cyanide due to the combination of free, weakly associated and refractory cyanide complexes) is required by most regulatory agencies for determination of effluent compliance. This method requires a distillation of the sample at low pH's and is most often sent to contract laboratories at a high time and monetary cost. This paper describes a new micro­distillation apparatus which allows for a multiple of CN,"' analyses to be carried out simultaneously saving both time and money. It can be used in the field, since only electrical power is required for the method. While not being appropriate for reporting values to the respective regulatory agencies as of yet, it is quite valuable for screening a large number of samples prior to submission of the samples to a contract lab for "official" reporting.

Jan 1, 1990

By J. M. Keane

Critical to successful dump and heap leaching for copper is an adequate testing program for evaluation of the applicable parameters. This paper deals with testing methods to establish best conditions for dump and heap leaching of copper so that commercial operations can proceed on a rational basis. Discussion is also offered of ore occurrences suitable for dump and heap leaching.

Jan 1, 1985

By K. J. Shelswell

This work describes the design, analysis, and comparison of discrete simulation and static spreadsheet models developed to compare the oreflow efficiency of two conveyor-based material handling systems; one approach with a conveyor stream in series and one with parallel conveyor streams. Analysis and comparison indicated that daily rates were significantly affected by random conveyor failures in both designs. The compound effect of random failures limited the effectiveness of long belt assemblies in series, while the parallel conveyor stream design partially alleviated this constraint. The static spreadsheet model predicted a lower average daily oreflow rate for the series conveyor stream design and a higher average daily oreflow rate for the design with parallel conveyor streams when compared to the discrete simulation results. These discrepancies were the product of model sensitivity to operational factors incorporated in the system and provided the opportunity to further use the discrete simulation models for trade-off comparisons and sensitivity breakdowns of mine operating practices and material handling system efficiencies in both the series and parallel belt stream designs

Feb 23, 2014

By A. B. Cecala

The Bureau of Mines performed a study to determine optimal locations for longwall face methane monitoring equipment. Longwall face ignitions continue to be a concern to the U.S. coal mining industry. Gains in ignition control technology have been somewhat negated by advances in longwall productivity. More reliable, heavy-duty longwall face systems generate higher production rates and increase methane liberation rates. These rates will likely continue to rise in the future as further coal production increases occur. Efforts will continue in the areas of methane drainage, methane containment, and methane dilution. In addition, more effective face methane monitoring is needed. As technology continues toward automated longwall panels, the importance of monitoring for methane at the shearer becomes even more significant. Since the primary face ignition source is the shearer mining machine, the Bureau ran tests to determine the best location to take methane readings on the shearer. This information, in conjunction with data obtained from field studies, provides a knowledge base for selecting optimum face methane monitoring locations.

Jan 1, 1993

By R. D. Ellison, D. K. Shukla, D. E. Stephenson

Seals for man-made penetrations into or nearby nuclear waste repositories require several unique capabilities not common to seals for conventional underground activities. Design criteria include long functional use, extremely low permeabilities of the seal zone (including adjacent disturbed rock), and the potential for retarding radionuclide travel. This paper summarizes comprehensive seal programs being conducted by D'Appolonia for the Office of Nuclear Waste Isolation (ONWI) at Battelle, Columbus. The program schedule requires the first detailed conceptual design for a bedded salt site to be completed in 1982. Conceptual designs for other host media will follow as site exploration data becomes available. The design program is supported by a variety of office, laboratory, and field activities being conducted by ONWI subcontractors. An example is provided to illustrate the variety of efforts directed toward determining the extent of disturbance adjacent to penetrations as a result of in-situ and excavation methods. Also, the current "working design" for the shaft and tunnel seal system at the candidate Los Medanos thick salt site in southeastern New Mexico is presented.

Jan 1, 1981

By Trevor Ellis

The following is extracted from a report by the author to the International Valuation Standards Committee (IVSC), with minor modifications for the purpose of publication. The author represented the IVSC at the annual session of the Ad Hoc Group of Experts on Harmonization of Fossil Energy and Mineral Resources Terminology. This is a body organized by the United Nations Economic Commission for Europe (UNECE). This second session, held in Geneva, Switzerland, achieved an important agreement for advancement toward uniform global standards for the classification of minerals and petroleum reserves and resources. Attendees discussed the possibility of enhancing the United Nations Framework Classification for Energy and Mineral Resources (UNFC) for implementation globally as the classification standard for use in financial reports under the International Financial Reporting Standards (IFRS). Presently, there are between 100 and 200 mineral and petroleum resource classification (or definition) systems throughout the world — a similar number to what there are countries.

Jan 1, 2006

By Zhang Youdi

A two-step approach has been developed for surface mine short term planning by the authors. The first step is mid term control and planning by the use of Goal Programming. This step gives optimal results for mid term planning (i. e. yearly or quarterly mine plan) as well as a macro control for short term planning (i. e. monthly or weekly plan.) The second step of the approach deals with short term production scheduling by the application of CAD technique and Systems Simulation. An interactive color character graphic design system has been developed with a software package. The menu-driven and module- structured package provides sufficient functions for surface mine short term planning and makes the model very flexible and user-friendly. This model has been applied to a large surface coal mine for short term planning optimization. Satisfactory results have been obtained. It is concluded that for complicated mining conditions this two-step combined approach gives an optimal control of mid term planning, makes the short term planning easier to avoid blindness; it has been proven that the Goal Programming is a powerful tool for solving multi-objective decision-making problems; guided by GP mid term planning, the CAD technique and simulation software package for short term planning are able to be concentrated on their practicality and flexibility.

Jan 1, 1992

By M. Deul

For the first half of the 21st Century the USA will rely on the same mix of fuels as for the past 50 years: Petroleum will cost more and availability will decline as developing nations modernize. Increased use of natural gas for electric power generation will result in severe stress on gas supply. Coal will be the fuel of last resort. More than half the petroleum used is imported, about the same amount as used for transportation. Only coal can provide relief by fueling railroads through electrification while encouraging ‘piggy-back’ trailer haulage, co-generation for manufacturing and expanded passenger service.

Jan 1, 2002

By Stanley Dempsey

INTRODUCTION The mining industry has been under- going a significant restructuring for the past several years. Some firms have been liquidated. Some have been merged with other firms. A number of mining divisions of larger firms have been spun off, in some cases in leveraged buyouts by management. Recently, there have been a number of spin outs of gold subsidiaries. There are also a number of start-up situations where new firms are emerging as significant gold producers through mine development or acquisition. This restructuring has created an attractive market for specialized mining finance firms, and a number of firms have recently entered that field in the United States. These firms provide financial advisory and valuation services to mining firms and project developers, and access to venture capital. In some cases, they invest for clients or for their own account. I have been asked to describe how our firm works, and what kind of information we expect to receive when mine developers seek our assistance in financing a project. HOW WE OPERATE Denver Mining Finance works for both mine developers and investors. We also provide expert advice on mining issues to governments and to firms who are in litigation over mining issues. A lot of our work involves valuing mineral interests for various purposes. Our principal expertise is in the technical, commercial, and financial area. We help put mining deals into shape commercially so that they can be financed, and we help investors get into mining deals that are commercially sound. We work on projects, but we also advise mining firms on the structure of their business and how to make the most out of one or several mines that they might own. In addition to our work for clients, we are also prepared to invest in mining projects for our own account, and to recommend gold properties for acquisition by our parent company, Royal Gold, Inc. We are, to some extent, a venture capital firm, in that we sometimes work with projects that are not "bankablerV1 and are prepared to invest in attractive early-stage situations in mining. However, I want to emphasize that our principal focus is on development of commercially attractive mining projects that can be brought into production in the best possible financial terms. If we can make a project qualify for a project loan from a commercial bank, we will not advise the developer to use high cost venture capital. For the purpose of this paper, I will focus primarily upon our functions with respect to development of precious metal projects. In a typical case, a firm with an advanced-staged project approaches us for help with financing the final feasibility study, and construction and operation of a mine. In some cases, the developer has already developed a financing plan and wants only our access to investors. If we agree that the project is sound and that the financing scheme will be attractive to investors, we will help the developer reach investors on a commission basis. In such cases, we are particularly insistent that the financing plan and our participation meet all regulatory requirements, particularly compliance with state and federal securities laws. In most cases, however, the developer asks us for advise both on how to structure the financing, and how it can be implemented. Here we work for fees based on hourly rates for advisory work,

Jan 1, 1987