Search Documents

By Georgios Kafantaris, Carsten Bonde, Nataša Katic

Within the investigation works for the Copenhagen Cityring metro, Geo/CMT have carried out 90 geotechnical boreholes. Together with the previously available investigation, this resulted in more than 15 km of vertical drillings and several thousands of laboratory tests. The design is made for 17 stations, four shafts and two parallel 16 km long tunnels. The geotechnical investigation and design have been carried out in several stages comprising appropriate refinement of structural design and design of excavation operations, including TBM break-in and launching operations at each station shaft. Acceptance of the solution and / or refinement of the investigation and design schedule in the next stage were based on the geological conditions, area availability at surface level, planning and cost-control criteria. The applied recursive design refinement is presented herein with an example of the Østersøgade shaft location.

Jan 1, 2016

The National Institute for Occupational Safety and Health (NIOSH) conducted a monitoring field study to optimize the rib control plan in a room-and-pillar coal mine. The study mine is located in the Central Appalachia coal basin. Two monitoring sites were selected at different sections in the study mine. The selected sites have different overburden depths and geologies. The instrumentation plans at study sites include borehole pressure cells installed at various depths in studied pillars, rib and roof extensometers and load cells mounted on number of the rib bolts. The instrumentation results and observed geology for one of the study sites showed great potential for optimizing the rib bolt plan at that section of the mine. Therefore, a rib support optimization study was followed using numerical modeling technique. A calibrated threedimensional model was developed using the instrumentation results of the optimization section. The calibrated model was used to determine the optimum rib support for expected overburden depths and rib heights. Baseline rib bolt patterns were assumed for the optimization study. Additional rib bolts, above and beyond the baseline bolting parameters, were outlined and identified as solutions to contain the rib fracturing identified by the modeling results.

Jul 28, 2020

By QUANWEN PU, Yonggang Wei, Bo Li

The spent catalyst is one of solid waste resources, which contains precious metals with considerable recovery value. However, due to the different compositions of catalyst, the recovery process is difficult. Most of the catalysts are supported by alumina which has good alkali-soluble properties, while platinum is insoluble in alkali. Platinum is enriched by pressurized alkaline solution which is a kind of hydrometallurgical process. The novelty of this study is the separation of alumina and platinum from the spent catalyst and the enrichment of platinum in the solid phase. In this study, a leaching process using NaOH as leaching agent under high temperature and pressure was employed. The effects of alkali concentration, leaching temperature, leaching time, and liquid–solid ratio on leaching efficiency were investigated. The optimum process conditions were determined as follows: alkali concentration of 240 g/L, temperature of 200℃, pressure of 1.20 MPa, time of 1 h, liquid–solid ratio of 5:1. It was concluded that the leaching rate of alumina can reach 99.69%. The content of platinum increased from 0.1749 to 21.12%, the loss of platinum was 3.39%, and the enrichment ratio of platinum increased by 120.82 times. The leaching kinetics of alumina was studied based on the shrinkage core model. The activation energy of alumina leaching is 19.53 kJ/mol, and the leaching process is controlled by chemical reaction. Pressurized alkali solution can not only efficiently leachate alumina from the spent catalyst and enrich platinum, but also reduce the reaction time and increase reaction rate.

Feb 11, 2022

By Ian McFeat-Smith, Robert J. Fowell

Roadheader machines have a specific place in modern tunnelling, not simply as a compromise between drill and blast techniques and full face machines, but as an economic and versatile form of mechanised tunnelling where the method of excavation is easily integrated with tunnelling operations. In the past, roadheaders have been subjected to misuses by engineers who failed to realise that, as in all mechanised tunnelling, a planned and systematic approach is essential if the full potential of these machines is to be gained. An increasing awareness of this, together with the introduction of the more powerful roadheader carrying their cutting potential into the hard range of rock is changing this situation and now makes the prospect of using roadheaders particularly attractive (1). The advantages gained by employing these machines can be considerable and Table 1 lists some of them. This table illustrates that from both cost, and installation points of view, the roadheader has considerable benefits over the full face machine. However, the principal advantage gained is in broken ground where heavy supports can be installed immediately at the tunnel face. In addition, access for planned maintenance and repairs to most working parts of the machine is at a premium and average machine utilisations of 40 - 60% can be expected. In comparison to drill and blast methods, up to 40% better progress can be regularly achieved, and the subsequent savings in overbreak costs alone would more than pay for the cost of a roadheader used to drive a 3km long tunnel. As with full face machines, ground disturbance is minimal and for short tunnels in urban areas a road-

Jan 1, 1979

By Victor F. Hollister

Porphyry copper deposits can be categorized into three models for purposes of prospect evaluation: Breccia-pipe, modified Lowell and Guilbert, and diorite models. The modified Lowell and Guilbert model is normally associated with a quartz-bearing intrusive and a potassic, phyllic, argillic, and propylitic alteration sequence. Variations can occur in the alteration zones of this model that range from orthoclase-rich (Kalamazoo, Silver Bell, and Mineral Park) to ortho- clase-deficient (Petaquilla and Bougainville) potassic zones. The unifying features of the model are the presence of a phyllic zone and a quartz-bearing intrusion. The breccia-pipe model (Toquepala) is characterized by structure and alteration related to or controlled by breccia. Where tourmaline occurs in the breccia, the identity of the model is usually clear. However, if tourmaline is not commonly developed in the breccia (La Caridad), the deposit can be misidentified as to model. Porphyry copper deposits associated with quartz-deficient intrusives, whether these are calc-alkalic diorites or alkalic plutons, are characterized by alteration suites distinct from those of the modified Lowell and Guilbert model. These have been generalized as diorite model porphyry deposits. Because alteration and mineralogical development in diorite model deposits is distinct from that of the modified Lowell and Guilbert, ore guides and exploration tactics differ for the two models. The reprint that follows describing the three prospecting models summarizes their features. It is to be emphasized that these are models used in exploration for specific deposit types and are not genetic, tectonic, or geographic models. Porphyry copper deposits can be metamorphosed. Gibralter is an example of a Lowell and Guilbert model deposit that has undergone regional metamorphism.

Jan 1, 1991

By J. O?Hanlon

The 4500 m3 blast furnace at the Redcar Works of ESC operates or, a burden of sinter and pellets, both materials being produced within the works. The early history of the furnace was given to the AIME Ironmaking Conference in 1981(1) when the burden was 65% superfluxed minter and 33% acid pellets. While ironmaking performance was adequate, it was felt that there were advantages to be gained by the use of fluxed pellets. For example, Kobe Steel had reported (2) that the rise of 30-50% dolomite fluxed pellets had enabled them to achieve better furnace permeability, higher gas utilisation, and enhanced ore/coke ratios. It appeared probable to BSC that the use of magnesia-bearing fluxed pellets would give a burden which had compatibility of softening and melting properties, i.e., fluxed sinter and dolomite pellets would result in a thinner cohesive zone because of closer matching of softening and melting temperatures, with consequential benefits on furnace stability and efficiency.

Jan 1, 1983

By G. Avolio, M. Gilbert

INTRODUCTION The city of Alexandria, Egypt is located on the Mediterranean Sea at the northwestern edge of the Nile River delta. The city is approximately 26 km long and 3 km wide bounded by the sea to the north and Lake Maryut to the south. The Alexandria Project is split into 2 phases: phase one included designs to update two existing primary wastewater treatment plants, five pump stations and over 75 km of sewer pipe, 18 km o f which is tunneled, (1500mm to 2750mm ID pipe). Currently the pipeline and pump stations are under construction. Phase two of the project includes expanding both the capacity of the treatment plants and the limits of the collection system. Included in this system expansion is the 3.5 km long, 2250mm ID Central Zone Conveyance, which is the subject of this paper. The project is under the direction of The Alexandria General Organization for Sanitary Drainage (AGOSD). It is an USAID funded joint venture of two American firms, CH2M - Hill and Metcalf & Eddy who share equally the major portion of the work and two Egyptian firms, Engineering Consultants Group (ECG) and Wairth Associates who are also partners. The venture, which is both design and construction management, worked under the name Wastewater Consultants Group, WWCG. Michael Gilbert was Chief o f the Geotechnical Department and Project Engineer for the Central Zone Conveyance. Gennaro Avolio was Geotechnical Exploration Manager for the Alexandria Wastewater Project.

Jan 1, 1987

By L. Korkiala-Tanttu, M. Rinne, Z. Song

Disposal of mine tailings has been recognized as an unavoidable burden of mining companies and local authorities. Conventional methods dispose mine tailings in a passive manner which hardly generates any value from them. On the other hand, growing local communities close to mines need more infrastructures which require great amounts of raw materials. In view of the above mentioned situation, a novel utilization of mine tailings is explored as alternative material for asphalt pavement, in order to extract more value from mine tailings and solve the high cost of pavement material. Inherent physical properties of the mine tailings were first investigated to find out their availability as pavement material. Then test specimens were made as mixture of the mine tailings and other pavement material to be tested in laboratory. The mine tailing materials presented a considerable potential as asphalt filler for low-volume roads. Furthermore, the limitat

Jan 1, 2011

By R. M. Bowen

To help solve problems associated with the optimization of complex coal preparation systems, a mathematical model has been assembled which can simplify calculations pertaining to the core of the plant, i.e. the coal cleaning section. It uses algebraic expressions, derived by fitting hyperbolic equations to Mayer curves, to calculate optimum settings for a specified array of coal cleaning units and feeds. This is done without search procedures, and with usually only minor iteration of a simple calculation to specify optima within 0.02% of specified product ash contents. The key to the calculation is a relationship derived via the analytical geometry of conic sections facilitating easy application of the incremental ash theory of separations. The model has been assembled in a generalised form to cater for N processes in parallel, each giving M separations to produce P final products. Examples are given involving assessment of some complex circuit options.

Jan 1, 1986

Mine managers need useful data to support production and maintenance decisions; for example, to evaluate the performance of replacement components. Today, managers rely solely on past experience, supervisors, opinions, and time studies. Our paper describes the concepts and algorithms we are developing for an automatic, intelligent decision support system (IDSS) that will aid managers by reducing and analyzing large amounts of, monitoring system sensor data and report only key production and maintenance information.. IDSS contains a pattern recognition, subsystem (IDSS/PRS) prototype to report graphical trends in traditional time study elements. We are designing. and prototyping a knowledge representation subsystem, using Knowledge Craft Tools, that will learn and adapt to the dynamic mine environment and reason about the recognized patterns using representations of manager's knowledge, equipment, capabilities, and mine layout and operating procedures. This subsystem will reduce, large quantities of time study type information to key issues that interest different managers.

Jan 1, 1989

By D. Corrigan, A. Ahmad, R. Sood, J. Bratt, R. Holt

Zinc oxide based electronic ceramics are being used increasingly to protect electric and electronic circuits against transient voltage surges. Varistors are produced by sintering and annealing ZnO based powder compacts through long sintering and annealing cycles. Because of the length of these cycles, a manufacturing plant is saddled with expensive high temperature equipment with low throughput. Ceramics Kingston Inc. has developed a new technology that uses 2.45 GHz microwave energy for sintering and annealing. The new technology has the potential for increasing equipment and labour productivity very considerably. Additionally, the new technology will result in appreciable energy savings and add flexibility to the manufacturing process. Microstructural examination of varistors sintered conventionally and by microwave technology showed considerably smaller grain size in the microwave sintered materials. The electrical properties of the microwave sintered ceramics compare very favorably with those of the ones sintered conventionally.

Jan 1, 1990

By S. J. Boone, A. Poschmann, C. Pound, A. Pace

San Diego’s Stadium Conglomerate consists of poorly cemented cobbles, gravel, sand, silt and clay. Conventional laboratory and in-situ testing is not suitable for characterizing its engineering properties. Although the formation is often considered a “rock” its behavior is more readily modeled using soil mechanics. Static and seismic design of a tunnel for the Mission Valley East light rail extension required that the stress-strain characteristics of the ground be identified over a broad strain range. Geophysical methods and field plate load testing were used to develop a full non-linear stress-strain model of the expected ground behavior. Quantification of the coarse material distribution was also required for selection of tunneling methods and construction considerations.

Jan 1, 2001

By Stefan Norgaard

In today's modern gold mining industry in Australia, and the world, more and more companies are recognising the competi­tive advantages gained by implementing an effective training program for operations (processing plant) personnel. Plant operators, or process technicians, are unique amongst all other gold mine employees. They are at work in shifts cov­ering 24 hours a day and their actions can have a profound effect on the operation's economic performance. To a large degree, the minute to minute decisions and actions of an operator can deter­mine whether gold is extracted to bullion in the goldroom or is discharged into the tailings dam. Experience has suggested that most small to medium sized gold operations in Australia, and even some large ones, have not implemented an effective training program. This is not attrib­uted to deliberate negligence or "anti" attitudes against training, moreover mill superintendents and metallurgy managers are technical people not oriented to human resource techniques. Usually the demands of designing, constructing and commis­sioning a gold plant overshadow the need for training in the first instance, In fact some well designed plants treating friendly oxide friable ore have little need for a dynamic well trained oper­ating staff. However, many plants do require a thinking team to optimise production and changing ore conditions towards the end of a mine's life can expose poor competence levels at large expense. Few managers will argue that training is a necessity and results in a win-win situation. The operators win by increased job skills, job satisfaction, clear career development and possibly better pay conditions. Trained personnel usually reciprocate with increased effmt and work ethic. The company wins also by having a thinking team which will maximise gold production and reduce operating costs.

Jan 1, 1998

In west-central England, 183 m (600 ft) below the Cheshire Plain, lie the evaporate remains of an ancient sea. Stratified into nine beds of salt separated by marl bands, the deposit stretches roughly 21 x 12 km (13 x 7.5 miles) and contains reserves of rock salt estimated as high as 400 Gt (440 billion st). The Winsford Salt Works, one of England's largest underground mines, extracts the Cheshire salt and sells it for use as animal feed, for application in de-icing programs, and as a key ingredient in sodium fertilizer production and a variety of other industrial processes. Because road de-icing is an important market, demand for Winsford's salt varies with the severity of British winters. Design capacity is 2.25 Mt/a (2.5 million/year). However, production peaked at 2 Mt (2.2 million st) in 1987. Over the past five years, annual production has averaged 1.6 Mt (1.7 million st). Run-of-mine salt averages 92.5% NaCl, mixed with about 5% marl. The marl was formed by deposition of a reddish dust blown into the Cheshire basin from deserts in what is now central Europe. Association with the marl adds color to the salt, producing tea-colored crystals that resemble unrefined sugar. Adaptation of coal mining systems Rock salt mining in the Winsford district began at least as early as 1682. Mining at the current site dates from 1844 but was shut down from 1892 to 1928. In the early 1900s, a series of catastrophic collapses and floods plagued and ultimately shut down then-active Cheshire brine-salt producers. Subsequently, Winsford reopened and began adapting mechanized underground coal mining systems to rock salt extraction.

Jan 1, 1992

By Peter E. Hart

The search for mineral deposits is a difficult high-risk enterprise whose likelihood of success is influenced by a great many factors. Among the most important of these factors are the knowledge and judgment brought to bear on an exploration problem. If, for example, a panel of expert highly experienced geologists could be convened to examine every prospect, it is at least plausible that fewer deposits would be overlooked in the exploration process. Unfortunately, whether a project is undertaken by a private company or a government agency, it is not usually feasible to convene such a panel. Our purpose in this chapter is to describe an experimental system of computer programs called PROSPECTOR that is intended ultimately to provide expert consultation on problems of mineral exploration and resource evaluation. Ideally, PROSPECTOR would serve as a surrogate for a panel of expert economic geologists. However, because the cost of computation is very low and is projected to drop by a factor of about 100 over the next two decades, systems like PROSPECTOR could be made available to the exploration enterprise at large. When consulting about a prospect, the PROSPECTOR system first gives the field geologist an opportunity to tell the program about the most significant features of the site: the major rock types, minerals, and alteration products. The system then compares these observations with a number of stored models of various types of ore deposits and forms alternative hypotheses about the types of deposits that might be present. The system next engages the geologist in a dialogue in order to obtain additional data that would be useful in resolving the multiple hypotheses. The geologist can interrupt the system at any time to obtain clarifications of questions, volunteer additional data, request the reason a particular question has been asked, or obtain a general summary of the state of the consultation process.

Jan 1, 1979

By D. A. Lee

The selection of control system equipment for a mineral plant is based on several criteria, including opera tor interface, supervisory capabilities, ease of maintenance, ease of programming and configuration, compatibility with auxiliary control equipment, and total cost. The paper discusses the technical evaluation procedure with respect to control system equipment available today.

Jan 1, 1988

By Lijun Xu, Ragula Bhaskar

The transport of dust particles from a turbulent air stream on to the surface of a mine entry is mainly due to the effect of diffusion, sedimentation and inertial impaction. While the literature in aerosol science contains many references on particle deposition, most studies apply to smooth surfaces in small, short tubes. The deposition data from those experiments may not be applicable to deposition in mine airways that have large areas of rough surfaces and extend several thousand meters. This paper describes the mechanisms of mine dust transportation and deposition, specifically, by estimating the turbulent deposition velocity for coal dust in mine airways. Data from in-mine experiments on ambient dust concentration and dust deposition along a straight entry were used. A statistical model for dimensionless turbulent deposition velocity was developed, and compared with the models developed by other researchers. The model shows that the distance from the dust source is an important factor in the turbulent deposition of mine dust.

Jan 1, 1995

By Thomas Fiest, Helmut Wannenmacher, Wulf Schubert, Manuel Entfellner

Mining and tunneling in so-called “squeezing ground conditions” at high in-situ stress can result in substantial and enduring ground deformations. The magnitude of deformations is closely tied to the applied excavation- and support concept, though typically, they can reach tens of centimeters. The yielding principle is based on the idea, that the need for support capacity decreases as deformation increases. To enable controlled ground deformation and safe working conditions, yielding elements as a part of the shotcrete lining are implemented. These types of elements avoid an overstressing of the shotcrete lining. During the deformation process, the support pressure of the yielding elements and lining increases, thus stabilizing the ground. Furthermore, long-term creep deformations of the rock mass can be absorbed with such a system. This economic support technique represents the state-of-the-art infrastructure tunneling practice in squeezing ground condition. A novel yielding element of High-Strength Expanded Polystyrene (HS-EPS) was invented, which overcomes existing systems’ drawbacks. This innovative system is lightweight and allows for safe and rapid installation. Furthermore, the modular setup of the element enables an easy on-site adaption to react to in-situ deformation patterns and changing ground conditions. Recent experiences from applications in Alpine base tunnels in squeezing ground are presented.

Jun 25, 2024

By Thomas A. Morley

This paper deals with the minimization of ventilation costs for the controlled-flow mine ventilation network. Cost elements considered include the cost of power and the fixed cost of the fans. The problem is modeled in a mixed-integer programming format and solved via the branch and bound method. Computational experience with sample problems is discussed.

Jan 1, 1983

By J. F. Rakszawski, Robert P. D'Orazio

The use of cyanide in the processing of gold has been documented for over a century. It is still one of the more effective methods of isolating gold, as witnessed by the fact that in 1987 cyanidation was used in the processing of 91.5% of the gold produced in the United States.

Jan 1, 1990