Search Documents

By E. R. Dotson

Kaolin is an important industrial mineral. It has unique properties, which combined with its low cost, make it suitable for use in a wide variety of products. Kaolin is defined as "any of a group of clay minerals, including kaolinite, nacrite, dickite, and anauxite, with a two-layer crystal in which silicon-oxygen and aluminum-hydroxyl sheets alternate; approximate composition is AlZ03-ZSiOZ-1/ ZHZO".-The kaolin discussed here is composed chiefly of the mineral kaolinite. Kaolin is also commonly referred to as "china clay". Approximately 4.9 kkg (5.4 million short tons) of kaolin was sold or used in the United States, and .8 million kkg (.9 million short tons) was -exported in 1974. In domestic usage, paper coating and filling accounted for 43% of the total, fol-2/ lowed by refractories, rubber, and ceramics.-Figure 1 shows the amount of kaolin sold or used by domestic producers for specified uses for the years 1963-3/ 1973.- Kaolin was produced at mines in 14 states, but Georgia accounted for 75% of the 1974 domestic production. The average value for all grades was $36.00/kkg 4/ ($32. 67/ton) .-

Jan 1, 1977

By Shankar Kumar, Arvind Kumar Mishra, Chitranjan Prasad Singh

Formulating a predictive model for blast-induced ground vibration (BIGV) has always been challenging due to the complex non-linear relationship between the BIGV and its influencing factors. Researchers have used empirical, artificial intelligence methods and numerical modelling methods to predict BIGV. In a dragline bench blasting, a massive quantity of explosives is used compared to other loading machinery, and the height of the bench depends on the size of the dragline. For effective utilization of explosives energy, decking is used to reduce the hazardous effects of blasting. In this paper, an attempt has been made for effective prediction of BIGV, and its mitigation on dragline bench blasting considering a deck length, stiffness ratio, hole spacing to burden ratio, hole depth to burden ratio, the distance of monitoring PPV from blasting site, Schmidt hammer rebound number of the bench to be blasted, and maximum charge per hole to total charge per blast. So artificial neural network (ANN) model and random forest (RF) model have been developed considering the parameters mentioned above. For the statistical performance of the predictive model, the coefficient of determination (R2) value is 0.8895, MSE is 22.84 for the ANN model, and the random forest (RF) model whose R2 is 0.8165 and MSE is 27.18. The sensitivity analysis results show that stiffness ratio, deck length, and Schmidt hammer rebound number are more influential parameters out of the selected parameters. The reduction of ground vibration with the introduction of decking led to a 3 to 15% reduction in ground vibration.

May 15, 2024

By Michael Gauna, William J. Gray, Joseph C. Zelanko

Mechanized mining in the underground coal industry has continued to evolve since the introduction of the remote control mining machine. Remote control continuous mining machines without an onboard operator’s compartment are now the norm in the industry. Extended cuts in excess of 30 ft (9.1 m) are commonplace. Unfortunately, machine operator positioning has become an often unrecognized safety concern, particularly when remote control continuous mining machines excavate a turn (turn a crosscut). From January 2001 through July 2004, remote control continuous mining machine operators or helpers have been involved in ten roof fall fatalities and eight machinery crushing fatalities. The machinery crushing incidents occurred when machines were being repositioned or moved to another place. Of the ten roof fall fatalities, three occurred while a crosscut was being turned and a fourth fatality occurred while mining was being conducted adjacent to the crosscut. The operating time associated with turning crosscuts is a relatively small part of the mining cycle. In recent years, however, a disproportionate number of fatal incidents appear to have been associated with this activity. Procedures for reducing the incidence of operator fatalities while turning crosscuts are discussed. These techniques include: minimizing the number of turn cuts, limiting turn cut depth, establishing no work zones and using visual warning devices to designate them, installing more roof/rib support in the vicinity of the turn cut, using notch cuts prior to initiating a full turn cut, and positioning the remote control miner operator in nontraditional locations.

Jan 1, 2005

By George E. Aikens

Prolonged subzero climatic conditions impose some unique engineering problems for the developer and operator of open-pit mines in the Far North. The remoteness of the job site and the extremely cold, long, dark winters severely tax both man and machine in the quest for the Arctic's rich mineral wealth. Undoubtedly the singular most troublesome problem for the engineer is Permafrost which underlies about 201o of the land area of the world and about 85% of the state of Alaska. Permafrost has its impact on building construction and mine excavation, while posing a more pervasive threat to the-delicate ecologic balance within the Arctic wilderness. Yet the difficulties associated with mining up North may not be as overwhelming as has been previously supposed. For example, the lowest temperature recorded at Point Barrow is -560F, whereas Montana has recorded -69.7° F.. There are no specially designed machines for mining and construction in the Arctic, and efficient equipment utilization is maintained through proper operation and servicing techniques. However, neither equipment or people can be assumed to function normally at -40°F. Special techniques in drilling, blasting, and ripping are being used to yield economically competitive ores. Overall, a fundamental understanding of the nature of Permafrost will allow the engineer to deal expeditiously with an Arctic mining venture and at the same time to deal fairly with Arctic environment.

Jan 1, 1972

By Levent Ozdemir, Robert J. Evans, Russell J. Miller, William Sharp

This paper describes the specifications and capabilities of a 6 ft (1.83 m) diameter laboratory rotary cutting machine which was designed and fabricated under a Bureau of Mines (USBM) contract awarded to the Colorado School of Mines (CSM). The machine will be used for carrying out research and development programs aimed toward improving the design and operation of mechanical tunnel, raise and shaft boring equipment.

Jan 1, 1983

By J. A. L. Campbell

Peabody's Camoy mining system is a truly continuous conceptual method of underground mining of coal. The system solves the three factors which limit coal from being mined continuously. Camoy's principal features are improved productivity and increased recovery. A conservative retreat production rate of 2 1/2 times normal continuous miner room-and-pillar mining rates are projected for a 6-7' seam. Overall mine productivity will be 2 times normal, with a potential for considerably higher rates. Major incremental production increases can be achieved by partial implementation of the system. Total mine recoveries of 75% are expected. The system includes both advance and retreat mining. The retreat half of the approach encompasses many of the features of short wall mining. A central panel is prepared for retreat mining by driving entries using room-and-pillar mining to the left and right of it. The room-and-pillar mining encompasses the advance features of Camoy. In the retreat phase, the roof of the face is supported by self advancing chocks or shields. All mining is done under the chocks by a continuous miner. As the miner advances the chocks continuously move forward behind it. Thus, as in a typical short wall system, continuous roof support is attained. Ventilation is unidirectional, another characteristic of short-wall type systems. Fresh air is brought in and passed over the working personnel. It moves to the face where the continuous miner is operating, picks up the generated dust and released methane, and is exhausted away from all personnel. Exposure to respirable dust and ignition hazards due to methane build-ups are almost totally eliminated. Thus, the second limiting factor is overcome and continuous ventilation is attained. Coal mined with the continuous miner is passed to a surge car and then to a Serpentix conveyor. The Serpentix, a Peabody invention, is a flexible conveyor capable of going around corners.

Jan 1, 1976

By J. R. Patts, J. P. Rider, J. A. Organiscak, A. B. Cecala

"The U.S. National Institute for Occupational Safety and Health completed a 15-month study at an underground limestone mine crusher booth that evaluated three research parameters: (1) the effectiveness of a filtration and pressurization system for improving the air quality inside the operator booth, (2) the relative effectiveness of ? > 99 and ? > 95 experimental prototype filters in the system, and (3) the performance of three different cab pressure monitoring devices. The protection factor was quantified monthly using particle counters in the respirable dust range of 0.3 to 1 µm particle size, and gravimetric dust samples were gathered at the beginning and end of the overall study. Under static (closed-door) conditions, the filtration unit offered a gravimetric calculated protection factor between 10 and 31, depending on the filter type and loading condition. The monthly particle counting analysis shows that the ? > 95 filter offers a protection factor nearly five times that of the ? > 99 filter, where n = 15 samples. The booth pressure monitors were tested and proved to be a valid indicator of system performance over time. IntroductionDesigned and installed correctly, enclosed cabs, operator booths and control rooms offer mine workers protection from noise and physical hazards, such as flying rock and debris, as well as a more comfortable environment in regards to temperature and humidity (Organiscak et al., 2016). While it is easy to quantify the operation of a cab’s air-conditioning unit by measuring the temperature, or observe whether the cab offers protection from flying debris, it is somewhat more difficult to quantify its performance in reducing respirable dust hazards.The U.S. National Institute for Occupational Safety and Health (NIOSH) has been conducting applied research to improve the air quality inside the enclosed cabs of mobile equipment, resulting in the mathematical modeling of enclosed cab filtration systems (Organiscak and Cecala, 2008). The same principles that govern the performance of filtration systems on mobile equipment are applicable to stationary enclosures such as operator booths and control rooms (Noll, Cecala and Hummer, 2015). While stationary enclosures are similar to mobile cabs, the work area can be significantly larger. Workers in booths and control rooms also tend to stay within the enclosure for a greater percentage of the day as opposed to workers on mobile equipment who enter and exit frequently."

Jan 1, 2018

By MAHESH SHRIWAS, CHRISTOPHER PRITCHARD

Ventilation monitoring and control in mines are becoming an integral part of day-to-day activity for maintaining the health and safety of miners. This paper evaluates potential real-time monitoring solutions for detecting and reducing diesel particulate matter (DPM), mine fires and dust in situ and examines the state-of-the-art use of ventilation monitoring and control in underground mines for detecting and reducing air contaminants to acceptable regulatory limits. In this study, relevant documents, including research papers, trade publications and manufacturer website information, are reviewed to identify research gaps. This paper also includes evaluations of contemporary sensors (airflow, gas, dust and silica), control system and software technologies, data transport systems, the Industrial Internet of Things (IIoT), ventilation network simulators and control devices to identify potential health and safety research gaps. Examples of some mines in Canada, Australia and the United States that have been using ventilation monitoring and controls are included as well. Overall, this review identifies multiple challenges and research gaps in applying mine monitoring and control systems that could be the focus of future research, offering potential improvements to miner safety and health and financial benefits.

By J. Alatalo

Autogenous grinding is a process of reducing the particle size distribution of an extracted ore by using the ore itself as the grinding media. It is a process that is difficult to control and there is a lack of knowledge of the events occurring inside the mill. To find out more about how the mill behaves under different processing conditions, a full factorial test was performed with iron ore in a pilot-scale pebble mill at the LKAB R&D facility in Malmberget. To complement this work, a strain gauge detector was embedded in one of the mill?s rubber lifters, the Metso Minerals continuous charge measurement (CCM) system, and was used to get more information about the charge dynamics. The data from the experiments has been analyzed. For production purposes, an increase in the number of particles smaller than 45 µm can be regarded as a probable increase in the production rate. The analysis shows that there will be an increase in fines at 65% of critical speed, especially when the mill is 45% full. This setting will also increase the power consumption, but improves the grindability of the ore even more. The deflection of the lifters is smaller for lower critical speeds. A higher degree of filling also gives a smaller toe angle and a higher shoulder angle as expected.

Jan 1, 2011

By J. Alatalo

Autogenous grinding is a process of reducing the particle size distribution of an extracted ore by using the ore itself as the grinding media. It is a process that is difficult to control and there is a lack of knowledge of the events occurring inside the mill. To find out more about how the mill behaves under different processing conditions, a full factorial test was performed with iron ore in a pilot-scale pebble mill at the LKAB R&D facility in Malmberget. To complement this work, a strain gauge detector was embedded in one of the mill?s rubber lifters, the Metso Minerals continuous charge measurement (CCM) system, and was used to get more information about the charge dynamics. The data from the experiments has been analyzed. For production purposes, an increase in the number of particles smaller than 45 µm can be regarded as a probable increase in the production rate. The analysis shows that there will be an increase in fines at 65% of critical speed, especially when the mill is 45% full. This setting will also increase the power consumption, but improves the grindability of the ore even more. The deflection of the lifters is smaller for lower critical speeds. A higher degree of filling also gives a smaller toe angle and a higher shoulder angle as expected.

Nov 1, 2011

By Manuel Pérez-Tello, María M. Salazar-Campoy, Óscar Rodríguez-Hoyos

The Kaldo furnace is a type of top-blown, rotary reactor that is widely used for the production of precious metals. During the production of doré, a gas jet of compressed air is injected through a water-cooled lance to impinge upon the molten bath surface in the presence of molten metal and a slag phase. A common problem during operation is the difficulty in controlling the distance that the injection lance can penetrate through the reactor mouth without being splashed by the molten phases. Splashing may produce accretions on the lance surface as well as plugging of the nozzle at the lance tip. An additional problem may occur when the gas jet impinges upon the furnace wall and causes rapid wearing of the refractory linings. Because the conditions prevailing in the Kaldo furnace offers poor visibility to the human eye, its operation mostly relies on the empirical knowledge of plant operators and process engineers. A systematic study in a scale model of the Kaldo furnace under controlled laboratory conditions may be valuable to estimate the maximum penetration distance of the injection lance, and thus help improve the operation of an industrial reactor. From a fundamental perspective, the observation of the basic features of the flow patterns in the scale model may help elucidate the relevant phenomena governing the hydrodynamics in this type of system.

By Chee Theng

The Mineral & Metallurgical Processing Division (MPD) of the Society for Mining, Metallurgy & Exploration held the 13th MPD Student Poster Contest on March 1, 2023, during the MINEXCHANGE 2023 SME Annual Conference & Expo. The event showcased the work of 24 graduate and undergraduate students from U.S. and international institutions. The contest began in January when the students submitted one‐page abstracts for judging. In February, they prepared and presented posters that explained their research, and each student had five minutes to showcase their research to a panel of judges during the conference. In recognition of their efforts, the MPD provides monetary rewards to all participants. For graduate students, first place receives $1,000, second place $500, and third through seventh places $200 each, and for undergraduate students, first place receives $1,000 and second place $500. The main authors of nonplacing entries receive $125 each. Participation in the contest also includes a free ticket to the MPD Luncheon, where the winners are announced.

Nov 28, 2023

By Carrie Smith

The 2025 Women in Mining USA National Conference, held April 15-18 at the Grand Hyatt Riverwalk in San Antonio, TX, brought together hundreds of professionals for a fourday event focused on empowering women and creating space for all individuals in the industry. Under the theme “Empowering the Future of Mining,” the conference served as a dynamic platform for professional development, knowledge-sharing and cross-sector collaboration. Organized by Women in Mining USA (WIM USA), whose mission is to foster equity, sustainability and leadership in mining, the event featured an extensive agenda including workshops, keynote speeches, panel discussions and networking opportunities. Attendees ranged from industry veterans to emerging professionals and students, united by a shared commitment to progress within one of the world’s most essential and traditionally maledominated sectors.

Jun 1, 2025

By Qinghua Tian, Zhipeng Xu, Dong Li, Xueyi Guo, Liu Zhu

Tellurium (Te) is an important scattered metal. Known as the vitamin of modern industry, national defense and cutting-edge technology, it is the supporting material for new high-technology materials. Currently, its separation and extraction from Te-bearing materials face problems such as long flowsheets and high reagent consumption, giving rise to an urgent need to develop new methods for its recovery.

By Walter C. Labys, William A. Vogely, David O. Wood

INTRODUCTION The past decade has witnessed a literal explosion in formal modeling of energy systems and markets. This rapid development was stimulated primarily by policy issues arising from the energy price shocks of 1973- 1974 and 1979- 1980. The suddenness of this interest is illustrated by comparing the current and earlier editions of Mineral Economics. The third edition, published in 1976, includes an addendum to the section of projection and forecasting methods because, Since the foregoing chapter was written, major events in petroleum have caused an explosion in formal modeling efforts in the energy field.a In contrast, this fourth edition includes the present chapter on energy modeling, and a separate chapter on nonfuel minerals modeling. The considerable interest in formal energy models is based on the complexity of the system, in particular the interaction between technical and engineering data and designs, and economic behavior of energy producers and users. Energy is a vital component in the economic and social well-being of nations, and must increasingly be explicitly considered in developing economic growth and welfare policies. Energy models can contribute to policy development and analysis, both by improved understanding of the energy system, and of the interaction between energy markets and the economy, and as an explicit means of analyzing and comparing the implications of alternative policy actions. At their best, formal models can clarify and illuminate policy options. In this chapter we will survey the objectives, methods, and potential contributions and limitations of energy system modeling. Section 2 considers the objectives, scope, and approaches to energy system and market modeling. Methodological approaches are then discussed more formally in section 3. Our approach is to intro- duce each model type and method via relatively simple generic models, illustrating their use by a selective review of the applications literature. Section 4 shifts the focus from modeling methods to procedures for model evaluation and improving model credibility especially in policy research and analysis. We conclude with some brief remarks on directions and opportunities for future modeling research. ENERGY MODELS: OBJECTIVES, SCOPE AND APPROACHES The concept of a model usually evokes an image of a complex, computerized system of mathematical or econometric equations providing detailed information concerning the operation of the process being modeled. In fact. models may be simple or complex, formal or mental, depending upon the purposes for which the model is intended. Simple judgmental models may be most appropriate when monitoring the overall performance of a process. When more detailed information is required and/or when the model

Jan 1, 1985

By J. Noll, J. A. Organiscak, A. B. Cecala

"In recent years, significant strides have been made to optimize the design of filtration and pressurization systems used on enclosed cabs of mobile mining equipment to reduce respirable dust and other contaminants and provide the best air quality to the equipment operators. This synergetic effort has involved original equipment manufacturers building mining equipment, manufacturers of heating, ventilation, and air conditioning systems for mobile equipment, filtration and pressurization system manufacturing companies, as well as the National Institute for Occupational Safety and Health, and other government organizations. Considering all the advances made in this area over the last decade, one aspect that NIOSH still needs to assess is the longevity of optimal cab performance with respect to the quality (filtering efficiency) of the filters used in filtration and pressurization systems. In today’s culture, most health and safety professionals automatically believe that HEPA quality filters need to be used to provide the greatest level of protection to workers. Researchers at the Office of Mine Safety and Health Research for NIOSH hypothesized that HEPA quality filters may not be optimal for the mining industry and speculated that MERV 16 rated filters would be more appropriate in most cases. In order to test this hypothesis, NIOSH performed a two-year study comparing both HEPA and MERV 16 quality filters on two pieces of underground limestone mining equipment, being a roof-bolter and face drill machine. Testing showed at the 95 pct. confidence level that there was no statistical difference between the two efficiency filters on both pieces of mining equipment. Since the MERV 16 rated filters were less restrictive and provided greater cab pressure, and since they did not have to be replaced as often as the HEPA quality filters, researchers concluded the MERV 16 filters were the optimal choice for both pieces of mining equipment in this case study comparative analysis. INTRODUCTION When most health and safety professionals today think about filtration efficiencies and their correlation with protecting workers’ health, the normal assumption is the higher the efficiency of a filter, the greater the protection afforded to the workers. The next logical step is to believe that HEPA filters deliver the greatest protection for workers because they provide the highest filtering efficiency. Obviously high-efficiency intake filters are a necessity for an effective cab filtration and pressurization system on mobile mining equipment, but what is the optimal filter efficiency rating for achieving high levels of cab protection factor performance over the service life of filters? To address this question, the National Institute for Occupational Safety and Health (NIOSH) has performed an in-depth laboratory research study over the years simultaneously with numerous field studies to retrofit used enclosed cabs on mobile mining equipment with newer and more effective filtration and pressurization systems."

Jan 1, 2016

By Lina Ospino Ballesta, Oscar J. Restrepo Baena, Juan Diaz Martínez

Artisanal and small-scale underground gold mining in Colombia plays a significant role in the country’s economy, but it faces persistent occupational hazards that threaten worker safety. Despite mining economic contributions, outdated technologies, limited risk management practices, and insufficient regulatory enforcement have led to recurring workplace accidents, many of which have been fatal. This study presents a systematic review of mining-related accidents over the last decade. Through geo-referenced analysis, high-risk municipalities were identified, and the frequency of accidents was correlated with the mining legal status and operational practices of these municipalities. The findings underscore the urgent need for evidencebased interventions that are tailored to the country’s unique mining context. Ultimately, this research contributes to the global discourse on mining safety by highlighting practical pathways to reduce occupational risks and promote safer, healthier workplaces in resource-constrained environments.

Feb 22, 2026

By Y. Pan, P. Tukkaraja, R. BHARGAVA, V.V.S. VYTLA, S.J. SRIDHARAN

Panel caving is an underground bulk mining method that uses gravitational force to mine massive, steeply dipping and deep-seated ore deposits at lower operating cost. To control dust and gas emissions entering the production level during the extraction of ore from the draw points in a panel cave, relatively negative pressure is created in the cave by installing an exhaust fan in the exhaust drift located on top of the cave. As caving is a dynamic process, designing an effective ventilation system is challenging; therefore, estimating the airflow resistance offered by the broken rock inside the cave is critical. This study investigates the effect of changes in the bulk porosity of the broken rock on the cave airflow resistance using the computational fluid dynamics (CFD) approach. The results show an inverse relationship between the cave airflow resistance and the bulk cave porosity. The pressure-quantity characteristic curves presented in this paper provide valuable information for sizing and operating an exhaust fan used for a mature panel cave ventilation.

Nov 1, 2022

By Hongqiang Wang, Qingliang Wang, Eming Hu, Zhiwu Lei, Fang Hu, Rui Zhang, Wei Hou

Pyrite, a mineral associated with uranium ore, is closely related to uranium leaching. In this study, Ozone micro-nano bubbles (OMNBs), as an environmentally friendly advanced oxidation technology, were used for the first time to oxidize pyrite under experimental conditions to improve the leaching rate of uranium. A laboratory-scale agitation leaching experiment of pyrite was carried out with a pH of 1.0–3.0, gas flow of 1–3 L/min, ozone generation rate of 0.55–2.22 mg/s, and pyrite concentration of 0.1–5.0 g/L for 1 h. By adding three different co-oxidant: Mn(II), Mn(IV), and Fe(III), it was found that only Mn(IV) increased the oxidation rate of pyrite by 21.7%. The results of the scanning electron microscope (SEM) and X-ray photoelectron spectroscopy (XPS) show that the formation of Fe(III)-O film on the surface of the ore suppresses the oxidation rate of pyrite to a certain extent. Pyrite can be rapidly oxidized up to 57.6% by OMNBs, which is beneficial to uranium leaching. This method is expected to be used for in situ acid leaching of uranium with OMNBs injected into the ground.

Jan 3, 2022

By Nilufer Kursunoglu

Despite being crucial for meeting the world’s energy demands, coal mining operations present considerable health risks, especially when it comes to exposure to coal dust. Longwall coal mining, an advanced technique, has considerably enhanced production but made dust control more difficult. Due to its explosive nature, coal dust continues to be a serious and dangerous concern in the industry despite developments in safety technology. This study aims to comprehensively assess the risk of coal dust explosions by integrating fuzzy risk matrix and Pareto analysis methodologies, offering precise risk ratings for various root causes. A fuzzy risk matrix was developed to assign exact risk ratings to identified root causes. Additionally, a Pareto chart was used to identify the main reasons and suggest particular preventive measures. 17 significant causes were determined for underground coal mines based on the study’s methodology, and some preventive measures were suggested. In accordance with fuzzy risk rating values, root causes were divided into six categories. The root hazard with the highest risk rating was identified as ‘accumulation of inflammable gas/gases’. The proposed approach was used to examine incidents caused by coal dust explosions in Turkish coal mines in order to demonstrate the effectiveness of combining the fuzzy risk matrix and Pareto analysis for assessing coal dust explosions. This study gives not only a solid framework for risk assessment but also critical information for classifying the risks associated with coal mine dust explosions. The results highlight the critical necessity for proactive and preventive actions to reduce the hazards of coal dust explosions and protect the safety of mining workers.

Nov 16, 2023