Search Documents

By R. E. Vivas

Goldcorp is one of the largest gold producers in the world with projects in South, Central and North America. Goldcorp?s flagship operation is Peñasquito, a world-class, poly-metallic deposit that started production in 2010 which is one of the largest mines in Mexico. Since the early stages of the project, Goldcorp has used the most advanced technologies available to maximize its value. However, the implementation of optimum mine plans has been challenging to put into practice. This is due to the fact that the mine operation involves more complexity than the plans usually reflect. This challenge is an industry wide issue that presents opportunities for improvement. This technical session discusses the mine planning methodologies and procedures used to connect long, medium and short term planning strategies in order to bridge the gap and produce optimum mine plans that can be practically implemented in the field.

Feb 23, 2014

By R. Q. Honaker

Recent research has shown that enhanced gravity separators provide the opportunity to effectively clean I mm x 37 micron coal. At Southern Illinois University, a detailed experimental program was performed on a continuous Falcon Concentrator, which was found to achieve separations at mass throughput capacity values in excess of 100 tonnes/hour. The apparent particle separation density for I mm x 73 micron coal was about 1.60 with relatively high efficiency (Ep = 0.12). Typical ash and sulfur rejection values of 85% and 70%, respectively, were achieved while recovering 85% of the combustible material. Metallurgical and efficiency data from the evaluation are presented in this publication.

Jan 1, 1998

By J. F. Brune

This paper analyzes the explosion hazard resulting from the formation of methane-air mixtures in the mined-out gobs of underground longwall coal mines. Although direct examinations of the gob atmosphere are difficult due to the inaccessibility of these gobs, evidence from methane drainage practices and investigations of numerous mine explosions suggests that explosive methane zones can form within longwall gobs. Explosions and fires resulting from these methane accumulations have led to severe and fatal injuries to the miners. Most recently, this was demonstrated in the explosion of the Upper Big Branch Mine in West Virginia, where 29 miners lost their lives.The paper also reviews current research on numerical modeling of gas flows in longwall gobs and outlines how targeted injection of nitrogen into gobs can effectively reduce the volume of such explosive methane zones. The paper concludes that comprehensive monitoring of gas compositions, along the accessible fringes of the gobs along with inertization, improved ventilation schemes and further research are necessary to control this explosion hazard and make mining operations safe.

Jan 1, 2013

It had been more than a decade since this many booths were occupied at an SME Annual Meeting, but at the 2010 meeting in Phoenix, AZ 630 booths were sold to 470 vendors from the entire spectrum of the mining and minerals industry. Exhibitors such as Metso, FLSmidth, West-Tech, ABB, NIOSH, Eriez and Resource West took their usual prominent places on the exhibit floor and were joined by newcomers such as tunnel boring machine manufacturer Herrenknecht AG, Frontier Kemper, the International Society of Explosive Engineers and more than 100 other first-time exhibitors. On the floor, one could find everything from a new pair of boots to a new career in the recruitment pavilion where some of the biggest companies in mining (Barrick Gold, Freeport-McMoRan, Newmont Mining, etc..) set up shop. The following is a look at some of the companies and products that were on display at the 2010 meeting. For information about displaying at the 2011 annual meeting in Denver, CO, Feb. 27 to March 2, contact exhibits@smenet.org.

May 1, 2010

By L. J. Warren

Recent research at the Parker Centre in Pe1ih, Western Australia, has provided opportunities to reduce gold production costs by: reducing lime costs in the carbon-in-pulp process, understanding the mechanism of selective extraction of gold over copper using ammoniacal cyanide, and increasing throughput and improving overflow clarify in thickeners. This paper reviews the work of these three Parker Centre project teams, and highlights those instances where the results have been applied to plant practice.

Jan 1, 1998

By Lewis Gordon, Alan Morrow, Aundra Nix

At the ASARCO Mission Mill, a multivariable, predictive controller was used to optimize parallel grinding circuits, improving throughput and product size. Using a dynamic model of the grinding circuit developed from on-line testing the software manipulates 4 variables to control 14 quality and constraint variables in each circuit. Traditionally, model-based control in grinding is difficult due to ore changes. This is addressed via a novel method to predict mill overload and automatic model switching.

Jan 1, 2000

By A. Mai, J. S. Wakeman

The progress results of a pilot plant study on the effects of ball top size and other mill operating parameters are reported. Test series on taconite and quartzite crude ores using a 1.7-m diam primary mill in closed circuit with a vibrating screen indicate clear trends on the improvements of mill throughput and power consumption when using larger diameter balls. Possible effects on mill liner and ball consumption as well as future research plans are discussed.

Jan 1, 1987

By Y. Luo, S. S. Peng

Several issues deserve further attention to improve subsidence prediction accuracy. These include: subsidence initiation and development over a setup entry area; subsidence development after face stop; and subsidence over chain pillar. An intensive subsidence monitoring program has been carried out over several longwall panels. A large amount of subsidence data has been collected, analyzed and solution techniques developed. In this paper, some of the measured data. data analysis techniques and the developed prediction methods are presented.

Jan 1, 1992

By Andrew F. McKown, Lewis L. Oriard

Advances in explosives engineering are moving forward in several different aspects. These include improvements and new development in explosives products, the application of these products to blasting technologies, and the study of the peripheral effects of the use of explosives, such as ground vibrations and airblast. Topics of special interest in the last several years include new explosives and detonators, cap timing, explosive casting, high-speed photography, perimeter and slope control, air decking and mathematical modeling of blasting processes.

Jan 1, 1988

By Mahmud Esad Uluer, Aaron Noble

Respirable coal mine dust (RCMD) is one of the biggest occupational health hazards for underground coal miners. Coal extraction is a main source of RCMD. To prevent challenges related to RCMD from developing, it is vitally important to limit airborne RCMD and stay within the regulatory limitations for mine operators. The flooded-bed dust scrubber (FBS), mounted on a continuous miner, is one of the most widely used dust mitigation technologies in room-and-pillar mining, but it is limited by technical challenges, the most notably being the potential to clog. In this study, the impact of mesh design and surface modification on system efficiency is examined using different vibrating, liquid-coated, stainlesssteel mesh panels in a laboratory-scale FBS.

Sep 1, 2024

By F. D. Mendes, A. H. Martins

The high copper grade in the Igarapé Bahia (Brazil) gold-copper ore restricts the direct application of the classical cyanidation process. Copper oxide and sulfide minerals react with cyanides in solution, causing high leach-reagent consumption, raising processing costs and decreasing gold recovery. According to studies, a feasible solution would be to pretreat the ore to remove copper minerals prior to cyanidation. The goal of this experimental work was to study the conditions for the removal of copper from the Igarapé Bahia gold-copper ore by sulfuric acid leaching, applying a statistical approach to the experimental design. By using the Plackett Burman method, it was possible to select the variables that exhibited the largest influence on copper extraction at the sulfuric acid leaching stage. These variables were leach solution temperature, stirring speed, sulfuric acid concentration in the leach solution and ore particle size. The individual effect of these variables and their interaction influences on the experimental response were analyzed by applying the replicated full-factorial design method. Finally, the selected variables were optimized by the ascending-path statistical method, which determined the best leach experimental conditions for maximum copper extraction. The optimized leaching conditions resulted in a copper extraction of 75.5%. Keywords: Copper, Gold, Extraction, Sulfuric leaching, Optimization

Jan 1, 2003

By F. J. Sotillo

Mining in Peru is mainly concentrated on metallic and polymetallic ores of gold, copper, lead, zinc, silver, tin, iron, etc. However, little has been done to develop extensive and rich non-metallic or Industrial Minerals deposits with the exception of some silica and phosphate deposits. This paper presents the characterization and metallurgical studies for the development of a feldspar deposit. These studies showed that the special characteristics of the ore, such as high porosity, high Al2O3 content, low clays content, and sized material allowed us to obtain commercial products applying relatively simple and low cost concentrating unit operations. The characterization studies showed that the feldspar products contained no quartz and about 90% of albite (NaAlSi3O8). The 14x40-mesh size fraction product analyzed 5.91% Na2O, 22.56% Al2O3, 65.73% SiO2, 0.65% K2O, 6.50% CaO, and 0.40% Fe2O3; whereas, the 40x150-mesh size fraction product analyzed 6.22% Na2O, 24.30% Al2O3, 60.80% SiO2, 0.91% K2O, 7.06% CaO, and 0.54% Fe2O3. These products could be used for manufacturing glass, ceramics, refractory, and filters in different applications. In addition, Middlings, could be used as insulation material due to its porosity (bulk density of 0.828 Kg/dm3), analyzing 4.46% Na2O, 15.7% Al2O3, 67.2% SiO2, 2.57% K2O, 3.94% CaO, and 4.24% Fe2O3. The material showed a sphericity of 0.77, a roundness of 0.68, and acid solubility of 13.3025% on only washed and 2.72% effective for clean material suitable for use in these applications. No selective accumulation of the valuable mineral was observed at any specific size fraction. However, iron and titanium bearing impurities trended to concentrate in fine fractions (minus 70 mesh -212 µm-). Metallurgical studies demonstrated that this feldspar ore required sizing at 14x40 mesh and 40x150 mesh to render commercial products. In the case of the 14x40-mesh size fraction, the process involved magnetic separation, gravity separation, and flotation for feldspar (direct flotation) using a blend of primary and condensate amines. However, the reverse flotation for mica-biotite and iron bearing minerals was also possible using petroleum sulfonate. The metallurgical process for the 40x150-mesh size fraction required magnetic separation and reverse flotation of iron and titanium bearing minerals, the feldspar being reported in the sink material. Commercial products from this feldspar deposit for glass, ceramics, refractory, and filtration; and for the manufacturing of insulation material were obtained.

Feb 23, 2014

By B. M. Eiter

The impact of fatigue is seen not only in its effect on the job performance of haul truck operators but also on the health of the operator and the productivity at the mine site. Its impact can even extend outside of the mine site to the health and well-being of the surrounding community (Fourie et al., 2010). In this paper, a case study of a small, surface mining organization is presented. The goal is to highlight the fatigue risk management system implemented at the studied mine site. Mine safety personnel who were interviewed discuss the changes made to the infrastructure of the mine, to administrative areas such as the number of shifts and the use of vacation time, as well as the implementation of new technology into haulage vehicles. This paper reviews how these changes are supported in the research literature.

By K. Papke

Nine western states contain significant barite deposits, but most deposits are in Nevada, which has been the principal western producer for more than three decades. Nevada produces about 85% of the total United States production, but about one-half of the barite consumed in the country is imported. Approximately 95% of the barite is used in drilling muds. Sharply decreased oil and gas drilling, starting in early 1982, severely depressed the domestic barite industry. Other problems for western barite include long distances to the areas of major drilling, high railroad-freight rates, and increased barite imports. Bedded deposits, formed by submarine exhalative processes, account for almost all western production, and reserves are large.

Jan 1, 1983

By M. Ribeiro, P. So, P. Wong

Electrowinning is a process by which metals, such as copper or nickel, are recovered from aqueous electrolyte solutions resulting from the extraction of the metal ion from an acidic or basic leach solution. The electrolyte or “pregnant” solution is customarily forwarded to an electrowinning "tankhouse." In the tankhouse, the metal ions are deposited on cathode plates by electrodeposition and then recovered from the cathode plates. Other processes may be employed with other metals, such as nickel, zinc, among others, to produce an electrolyte from which their respective metals are obtained. During the electrowinning (electrodeposition) stage, elemental metal is plated out at the electrowinning cathode and oxygen evolves at an insoluble anode. The evolution of oxygen gas forms bubbles which entrain strong acid electrolyte, carrying it into the air above the electrowinning tank in the form of a fine mist or spray when the bubbles break. An acidic mist is generated above the electrolyte. This mist or spray then spreads throughout the electrowinning tankhouse. The acidic mist is corrosive and a health hazard and can cause extreme discomfort to the skin, eyes, and respiratory systems of tankhouse workers, especially during hot weather conditions. Polyfluoroalkyl based products (PFAS) have been widely applied as anti-misting agents in the electrowinning of metals in an acidic electrolyte. Functionalized PFAS compounds, however, have come under increased scrutiny by the EPA due to their impact on human health and the environment. There remains need for improved acid mist suppression agents for electrolysis and electrodeposition, particularly for products free of fluoroalkyl components.

Feb 1, 2023

By R. Adams

Zirconium is the 20th most abundant element in the Earth?s crust and it most often occurs in the form of silicate (as zircon), less often in the oxide form (as baddeleyite or caldesite). Historically, the world?s production of zircon was entirely derived from mining and processing beach sands or heavy mineral sands that were being exploited primarily for their titanium content, i.e., to generate TiO2 feedstocks that would be used for making titanium pigments and, to a lesser extent, titanium metal. Zircon was then regarded as a byproduct, with the sharply fluctuating prices typical of a commodity where the supply is essentially involuntary and not truly responsive to market demand. However, in recent years, zircon has shown considerable mining investment appeal in its own right. Projects have been planned ? and some have already come to fruition ? based mainly on the zircon potential of the deposit. Booming Chinese demand for zircon to meet the requirements of the ceramic and zirconium chemical sectors has been a major factor causing zircon prices (f.o.b. Australia) to surge from US$674/t ($611/st) at [ ] the end of 2005 to beyond US$2,400/t ($2,177/st) by the end of 2011.

Jan 1, 2012

By J. B. Malcolm

The discovery of tungsten-bearing quartz outcroppings in Vance County, N. C., by the Hamme brothers in 1942, made international news in the mining industry and was, in fact, one of the major ore discoveries made in the U.S. during the last 25 years. Operations began at the Hamme mine in 1942, but after 16 years of successful operation, the mine was closed down in 1958 under adverse market conditions. By that time, it had produced nearly 20 million lbs of metallic tungsten. Because of the square-set timber mining method then in use, mine operating expenses were high, actually representing 78% of the total operating expenses at the property. In timber work alone, 160 men were employed. Approximately 500,000 bd ft of timber were placed monthly at a direct supply cost of $1.00 per ton of ore mined. Late in 1959, following a slightly improved position in the tungsten market, company management decided that, by changing the mining method, the operation could be economically feasible. The major premise in this decision was that a reduction of from 25 to 30% of the mining costs could be achieved by the conversion of the mining method from square-sets to horizontal cut and fill. Reopening of the mine began in February 1960, Full production has now been reached and overall mine productivity has been doubled.

Jan 1, 1962

By J. O?Hanlon

The 4500 m3 blast furnace at the Redcar Works of ESC operates or, a burden of sinter and pellets, both materials being produced within the works. The early history of the furnace was given to the AIME Ironmaking Conference in 1981(1) when the burden was 65% superfluxed minter and 33% acid pellets. While ironmaking performance was adequate, it was felt that there were advantages to be gained by the use of fluxed pellets. For example, Kobe Steel had reported (2) that the rise of 30-50% dolomite fluxed pellets had enabled them to achieve better furnace permeability, higher gas utilisation, and enhanced ore/coke ratios. It appeared probable to BSC that the use of magnesia-bearing fluxed pellets would give a burden which had compatibility of softening and melting properties, i.e., fluxed sinter and dolomite pellets would result in a thinner cohesive zone because of closer matching of softening and melting temperatures, with consequential benefits on furnace stability and efficiency.

Jan 1, 1983

By Mike D. Adams

Testwork was conducted on loaded carbon samples from a small gold mine in South Africa. It was shown that a 75% saving in reagent consumption in the Zadra elution circuit could be achieved by adopting a cyanide-free elution approach, i.e. by cutting back the NaCN level from 1 % to nil, and the NaOH level from 3% to 1 %. This process change was also shown to result in a 20% improvement in the elution kinetics. Furthermore, it was also shown that a 50% enhancement in elution rate over the current situation could be achieved by use of an eluant containing 0.5% NaOH and 0.15% NaCN, corresponding to an 84% saving in reagent consumption. A further improvement in elution kinetics was found to occur by increasing the NaCN level to 3%, but this would lead to a concomitant increase in reagent consumption, due to the decomposition of cyanide at high temperatures. The presence of base metals loaded onto the carbon was also found to have a significant effect on the elution. Copper tends to adsorb as Cu(CN)2- during the adsorption stage, and acid washing converts this species to CuCN. Copper in this form is not eluted during cyanide-free elution, whereas it is eluted during a conventional cyanide elution, consuming the initial cyanide in the process. The elution data was analysed and the fit to a simple model was verified.

Jan 1, 1995

By Geoff C. Knight

Longwall mining using the shearer is acknowledged internationally as the most economically successful method of high volume production from underground coal mines. Since its introduction in the 1950s, a great deal has been achieved in developing the capability and reliability of the shearer - and the associated face conveyors and powered roof supports - to produce the competent systems now widely deployed. Equipment will continue to improve as knowledge and experience are gained and through the influence of market forces on the international equipment suppliers. However, current systems are so successful that further improvements are likely to be incremental rather than radical unless a high level of system automation is introduced. The automation concept is not new to the shearer-based longwall system. The opportunity and the need were recognized soon after the shearer and powered support were introduced in the 1950s. In the early 1960s, the British Coal Corp. (BCC; then the National Coal Board) attempted remotely operate longwall systems. Those imaginative early schemes were seen as failures at the time. But, with hindsight, a great deal was learned from the experience that stimulated automation research in several European countries. One of the most fundamental lessons learned was that coalface system automation is not possible until there is a high level of competence in automatically controlling the operation of the production machine itself within the coal seam. Once that is achieved, the rest of the system will follow with comparative ease.

Jan 1, 1991