Search Documents

By C. Mark, D. M. Pappas

From 1999 through 2008, groundfall events resulted in 75 fatalities, 5,941 injuries and 13,774 noninjury roof falls in U.S. underground coal mines, according to the U.S. Mine Safety and Health Administration (MSHA). A comprehensive analysis of these events was conducted to better understand where and why these incidents occurred. The first segment of the study used the MSHA database to evaluate groundfall injury rate trends related to mining method, year, locality, seam thickness, mine size, coalbeds and seasonal effects. In the past decade, roof fall injury rates have dropped 50%, but rib fall injury rates have remained constant. Room-and-pillar mines had a roof fall injury rate that was nearly 2.5 times the longwall rate. High groundfall rates occurred in the Illinois Basin, a finding that correlates with other studies that have shown that roof rock in the Illinois Basin is weaker than that in the central Appalachian coalfields. Finally, noninjury roof fall rates in the eastern and central United States were found to be 50% higher from July through September, possibly because of the changes in humidity levels that may cause shale mine roofs to deteriorate. The second segment of the study evaluated the root causes of failure by reviewing all MSHA groundfall fatality reports for 1999-2008. Pillar recovery was the leading cause of groundfall fatalities (19%), followed by rib falls, roof skin falls and traveling under unsupported roof (16% each). Defining prominent ground control incident trends and hazards will identify areas where additional study is needed and where innovative solutions need to be developed to reduce these severe occupational hazards.

Jan 1, 2011

By J. F. Mack, P. R. Michael, J. M. Shapaka, S. J. Self, M. W. Richmond

"On October 11, 2000, an estimated 306 million gallons of water and coal waste slurry drained from an impoundment in Martin County, eastern Kentucky into an adjacent underground mine. Approximately 230 million gallons of the water and slurry discharged from two underground mine portals and affected over 75 miles of streams in Kentucky and West Virginia. In response to this and several other similar events, the U.S. Office of Surface Mining Reclamation and Enforcement (OSMRE) commissioned an oversight study that evaluates how well state and federal regulatory programs established under the Surface Mining Control and Enforcement Act are ensuring that impoundment operators are minimizing the potential for impoundment-basin breakthroughs. The study focuses on slurry impoundments constructed in the hollows of Appalachia where numerous coal seams and steep topography combine to result in a large number of mined seams intersecting and underlying impounding facilities. Factors under consideration include: (1) full accounting of all mineable coal seams intersecting and underlying the impoundment; (2) identification and accurate location of underground mines close enough to the impoundment to potentially affect its stability; (3) assessment of the stability of coal barriers between the impoundment basin and adjacent mines, and stability of roof rock and pillars in mines subjacent to the structure; (4) determination of the flowability of the impounded slurry when expanding or undermining the facility are being considered; and (5) measures undertaken to reduce breakthrough potential when necessary. The oversight study began in 2012 after program-evaluation criteria were defined in an OSMRE technical position paper. The study is scheduled to be completed in 2017. BACKGROUND The Surface Mining Control and Reclamation Act (SMCRA) authorizes the disposal of coal mine waste by constructing a coarse coal mine waste embankment across a valley and pumping the fine coal mine waste (slurry) into the resulting basin (Figure 1). A concern shared by many engineers, geologists, and mine inspectors familiar with coal mine waste slurry impoundments is related to the common occurrence of underground mine workings adjacent to or beneath the impoundment: the potential for slurry “breakthroughs” into mine works and subsequent breakouts into the surface waterways (Figure 2). On October 11, 2000 a combination of coal refuse slurry and water from the Big Branch impoundment in Martin County, Kentucky broke through into an underground mine and subsequently discharged into the receiving streams. The location of the point of breakthrough, pathways of slurry/water flow within the mine workings, and two points where the liquid exited the mine are shown in Figure 3. An estimated 306 million gallons of water and coal refuse slurry drained from the impoundment into the adjacent underground mine. Approximately 230 million gallons subsequently discharged from the underground mine at two portals."

Jan 1, 2015

By Richard C. Travis, Edward C. Dowling

A detailed kinetic study of the flotation installation at the Metcalf Concentrator revealed a rougher flotation circuit operating under less than optimal conditions. Based on these results, a project was initiated to approximately double the rougher flotation capacity by increasing the installed volume from 780 cubic meters to 1,560 cubic meters. This project, which was completed in early 1991, replaced the existing cells with larger capacity cells. A comprehensive analysis of results demonstrates significant metallurgical benefits. INTRODUCTION/BACKGROUND The Metcalf Concentrator is located in Morenci, Arizona and is part of Phelps Dodge Morenci, Incorporated. Sumitomo Metal Mining of Arizona is a minority partner in the operation with 15% interest. The Metcalf Concentrator is the newer and smaller concentrator and operates in conjunction with the Morenci Concentrator. Operating capacity at Metcalf is currently 48,000 TPD of ore on a 365 days per year basis. The Metcalf Concentrator was commissioned in 1974 at a 30,000 TPD operating rate for the purpose of treating ores originating in the Metcalf Mine. The mine takes its name from the former town of Metcalf which was named for Robert Metcalf who was credited with discovery of the mineral district. The predominant ore mineral is chalcocite which occurs as a secondary enrichment closely associated with iron pyrite. The host rock is largely granodiorite and quartz monzonite. The original rougher flotation circuit consisted of a total of six rows of Wemco 8.5 cu. meter (300 cu.ft.) flotation machines treating pulp from the two grinding sections (Sections A and B). Each row was configured in a 4-4-4 arrangement. Shortly after startup the throughput rate was increased significantly without sustaining a recovery loss. This increase was achieved by raising the target value for the particle size of the cyclone overflow which is the rougher flotation feed. Shortly thereafter, the capacity of the pump and cyclone began to restrict further increases in throughput. After testing, two 66 cm. (26-in.) cyclones and a 12-in. X 12-in. centrifugal pump replaced the original classification equipment. As a result of these modifications, the grinding section could routinely process in excess of 42,000 TPD. Due to the increased tonnage rates, limitations in the rougher flotation circuit performance were observed. In an effort to improve the performance of rougher flotation with this higher throughput, the speed of the flotation mechanisms was increased from 230 RPM to 250 RPM. This change improved the suspension of the coarser feed and induced additional air into the pulp. It did, however, apply additional strain to the motors, shortening their life. At these elevated processing rates, it was found that the dart valves operated almost entirely at the top end of the control range and could not efficiently handle upsets from the grinding section. This was remedied by lowering the end overflow weir and allowing some of the tailings to overflow the end weir. However, in order to obtain acceptable recovery levels, the flotation pulp was maintained at a high level, adversely influencing the rougher concentrate grade.

Jan 1, 1993

By R. Owen

An overwhelming amount of data can be collected around the blasting process. This information can include blasting product, pattern design, blast results, and routing. It is only when these data sources are combined in a concise and accurate form that they are of real use in determining the safety and economic implications of each parameter. Two key technological aspects of blasting are drill fleet management (DFM) and size fraction analysis (SFA). As these technologies are integrated as near-real-time measurement and QA/QC tools, the resolution and realization of blasting parameters is significantly increased. The Freeport-McMoRan Morenci Mine has integrated these technologies along with other existing database structures to create a responsive and sustainable tool for reconciliation, forecasting and parameter matching. This ability allows Morenci to customize blast patterns to meet the criteria most critical to each shot, whether the impact is influenced by routing and recovery, equipment maintenance or safety concerns. DRILL FLEET MANAGEMENT The current DFM was stabilized in its current form in mid 2009 after database and hardware maintenance met stability requirements. Currently the system is running on 12 production drills. The system receives pattern layout and is capable of semi-autonomous drilling over the entire district. The fleet is capable of drilling in highly altered intrusive units and hard granites through the range of sedimentary and volcanic units that comprise the Morenci District. The system brings a level of accuracy not achievable with earlier paint-marked patterns. Depth control is also increased along with more consistent wear and maintenance patterns due to semi-autonomous drilling.

Jan 1, 2011

"It’s been 80 years since Charles Warman invented the iconic Warman slurry pump, a pump that revolutionized the mining industry and continues to push the boundaries of pump performance to this day.In honor of this legendary brand, Weir Minerals hosted an event at the end of May in Kalgoorlie, Western Australia. Throughout the evening, attendees relived Warman pumps’ history and gained an insight into some of the future innovations planned.“It was a privilege to share this special night with some of our key customers, past and present employees, and members of the Western Australian School of Mines,” said Ricardo Garib, divisional president of Weir Minerals. “Warman is one of our leading brands. It has truly shaped the mining industry over the past 80 years and is a product we are all very proud of. The Warman pump, invented to solve high wear issues in slurry pumping, created a thriving industrial business that is now the cornerstone of Weir Minerals with more than 8,000 people, and more than 150 manufacturing and service centers across the globe.”Always inventingCharles Warman invented the Warman slurry pump in Kalgoorlie in 1938. It was a hardwearing slurry pump that used replaceable liners and a replaceable impeller, something that had never been done before.“Charles Warman was a visionary and an innovator. The use of rubber lining in the pump was groundbreaking as it reduced total ownership costs, was safer to handle and offered extended wear life in many abrasive slurry applications. It is a great example of solving customer problems with material science, and is still taught in universities today,” said Marcus Lane, global product manager for centrifugal pumps at Weir Minerals.It was quickly adopted throughout the goldfields in Western Australia and by the 1950s, as customer demand rose, Warman expanded his business by opening offices in Sydney and Perth.During the 1960s the rapid growth of the business continued with manufacturing and sales outlets established around the world. The Warman Series ‘A’ pump was accepted and became a world leader in its field. Further work on the Warman AH pump resulted in the development of interchangeable metal and rubber wearing components."

Jan 9, 2018

In the grand scheme of things, the 9.5-t (21,000-lb) shipment of molybdenum concentrate that left Freeport-McMoRan?s Climax Mine site on May 10, 2012 was not unlike the thousands of others that have been hauled away from the site during the last century, except for the fact that this shipment marked the official rebirth of one of America?s greatest mines. For nearly two decades, 17 years to be exact, there was no production from the mine that was once the largest underground mine in the world and was so important to the Allies? effort during World War II that it was assigned the highest priority of any mine in the United States by the War Production Board. The economic recession in 1980 put an end to the mine?s success, and the Great Recession of 2008 nearly derailed the mine again. But, like the nearby town of Leadville, CO, the mine survived thanks to an investment of more than $700 million by Climax Molybdenum Co., a Freeport-McMoRan company, to bring the Climax Mine back into production.

Jan 1, 2012

By R. Y. K. Yang, O. Olajide, E. H. Cho

"This study focuses on partial leaching of coal pyrite with sodium sulfite in order to increase its degree of liberation from the coal matrix, which might help to increase the removal of coal pyrite, together with trace elements of arsenic (As), selenium (Se) and mercury (Hg) by froth flotation. The U.S. Bureau of Mines’ two-stage reverse flotation process was applied to further reject coal pyrite in the second stage, where pyrite was floated while coal was depressed. The results show that the leached coal flotation with sodium sulfite produced lower pyritic sulfur content in the clean coal by approximately 25% compared to the flotation of unleached coal. The synergism mechanism between the leaching and the two-stage flotation is delineated. The rejection of trace elements (As, Hg and Se) after the two-stage flotation process with unleached coal followed approximately that of pyritic sulfur (64.6%). However, after the two-stage flotation with leached coal, the rejection of Se was as high as that of pyritic sulfur (77.9%), while the rejections of As and Hg were 20% lower than that of pyritic sulfur, or followed approximately the same rejections obtained through the two-stage flotation with unleached coal.IntroductionSO2 is a reducing reagent, but when it is combined with oxygen in an acidic solution, it will become a strong oxidizing reagent for leaching coal pyrite. Sundaram et al. (2001) found that the reagent could leach coal pyrite to produce ferric iron, which, in turn, catalyzed the oxidation of SO2. Similarly, Cho et al. (2009) found that the reagent could leach pyrite as well as mercury from coal. In the present study, coal was preconditioned by partially leaching coal pyrite in water-coal slurry with sodium sulfite at 48° C. The partial leaching of coal pyrite may enhance its degree of liberation from the coal matrix and give a chance to be rejected more effectively during the flotation.The two-stage U.S. Bureau of Mines’ reverse flotation process (Miller, 1975) was used in this study. The first stage is conventional flotation, in which coal is floated while material with higher ash and pyrite content remains in the cell. Kerosene is used as a promoter to float the coal and MIBC (methyl isobutyl carbinol) is used as a frother. In the second stage, the floated coal from the first stage is depressed using a starch-based reagent, while coal pyrite is floated using potassium amyl xanthate. In this second stage, the liberation of coal pyrite from the coal matrix seems to be an important factor for successful rejection of coal pyrite."

Jan 1, 2015

By James C. Fowler

The use of ground-probing radar as a reflection mapping tool has expanded greatly in the last few years. This tool can now be used to produce near surface information which is very useful to geotechnical engineers. Using the lightweight field equipment now available, it is possible to use the radar within mines and tunnels to obtain information which may impact the safety and production of these operations.

Jan 1, 1979

By E. Forssberg

Studies have been carried out with the High Pressure Roller Mill, HPRM, to produce calcium carbonate minus 10 micron. This paper presents the optimization of the specific grinding force of the HPRM system for a maximum energy utilization when limestone is ground. In addition, experimental tests of producing carbonate minerals using the HPRM as a pre-crusher are described in this paper.

Jan 1, 1996

By F. M. Doyle, Robert G. Robins, E. Peters

Stability diagrams for the Cu-S-H2O system have been widely applied over many years. Stability diagrams for aqueous systems generally, have been generated by computer, but with the programs for Potential-pH diagrams in particular, a common routine leads to error in multi-element systems. In this paper these errors, and some misinterpretation of diagrams are considered. In most of the published diagrams for the Cu-S-H2O system there has been no account of the sulfide complexes of copper. Here, the free energies of formation for the various species in the system have been re-evaluated for consistency, and some diagrams for the Cu-S-H2O system ( generated with the program DIASTAB Vers.5 ) are presented.

Jan 1, 1993

By John Marsden, John Mansanti, Jim Arnold, Mike Gleason

DOUG HALBE: We're not quite to the end of our session, but we're close. We've had a lot of fun with some of these spill ideas. But these are serious problems, and I think we might be able to benefit by continuing to compile these. Several years ago, the metallurgists at the various operations of Gold Fields Mining Company had a newsletter that came out every two months for several years. This publication consisted of short articles by the staff at the various operations, plus a few others, on problems they'd had and how they solved them. One very useful article, "Things We'd Have Done Differently at Chimney Creek," was written shortly after start-up. John Marsden was the editor and John Mansanti contributed to it, as did Jim Arnold (our distinguished co-chair) and Mike Gleason. I would be interested, with the permission of the audience, in editing that article to make it a little bit less abrasive and putting it into the record here. I think it's a useful SME function to maintain a list of things we've done wrong in plant design, things we don't want to do again. If we have another open session in the future, would others be willing, even anonymously, to contribute, bring slides, and say "Hey, look at the goofs we made?" [laughter, followed by support from the audience] Okay, we'll plan on that. And we'll try to include the Chimney Creek list in the transcript of this session-perhaps edited a bit.

Jan 1, 1998

By Michael Michaylov, Elana Vlasseva

This paper presents a method for three-phase foam preparation recipe optimization. The pressurized foam is injected into porous media of gob area for prevention and fighting of SPONCOM fires. The method includes laboratory experiments for main foam properties as well as mathematical optimization procedure. Optimization criteria are formulated reflecting foam application purposes. The influence of solid phase on foam heat stability is shown. Results from optimization procedure for four foam agents by varying fly ash consistency of foam are presented. Theoretical basis for original construction of foam generator, specially constructed for of three-phase foam generation, is set u

Jan 1, 1997

By J. C. Emerick

Preliminary investigations have shown that wetland-based treatment systems can be an effective and relatively inexpensive control strategy for mine drainage pollution in eastern coal mining regions. This strategy also has potential for western mining regions, although too few systems have been installed in the west to permit general evaluation of the concept for western climates. The construction of prototype systems is encouraged for some situations. Wet-land environments have the capability of removing metals by natural geochemical and biological processes, including precipitation, filtration, ion absorption, and biological uptake and accumulation. Data presented for natural wetlands receiving mine drainage show removal of iron and other metals, and high accumulation of metals in soils and plants.

Jan 1, 1988

By C. D. Litton

This paper describes two new gas diagnostic techniques which have been used successfully to determine: 1) the combustion status of underground mines which have been sealed due to fire (Littol1 Ratio); and 2) the location of fires in abandoned, underground mines or waste banks (Kim Ratio). The Litton Ratio makes use of the rate of change of CO, calculated on both an air-free and methane-free basis, from mine gas samples and compares these values with those expected from a normal, combustion-free environment. The Kim Ratio uses the concentrations of total hydrocarbons, C2 ?C5, less the methane, to arrive at ratio values which increase as combustion intensity increases. The details of these two new techniques, their application to real situations, and their limitations will be discussed.

Jan 1, 1989

By Margaret Armstrong, Chris Roth

One advantage of kriging is that it provides both an estimate of the block or point grade, and an indication of the local precision via the kriging variance. If one assumes that the estimation errors are normally distributed, then confidence intervals for the grades can be calculated. But in mining, grades are rarely normally distributed; in general, they are skew. This is particularly true for precious metals. In this paper we study confidence intervals for variables with non-normal distributions. Using a non linear geostatistical technique, the grades are transformed into their normally distributed equivalents. Confidence intervals are obtained for these normal variables, and back transformed to give the corresponding confidence intervals for the grades, for either points or blocks. This approach is applied to gold data from the Witwatersrand basin in South Africa.

Jan 1, 1996

By P. C. O. Chukabarah

Atkinson's resistance square law is the cornerstone equation for traditional expression of energy losses in mine ventilation engineering. But the nomenclature for the various forms of energy losses are often confused for one another, misapplied or misinterpreted. These forms of energy were re-examined from thermodynamic and fluid-dynamic perspectives. Resultant expressions showed that both incompressible and compressible flow regimes in underground mines can easily be accommodated. Given the well-known three major energy forms, which are equivalent to one another but numerically unequal, corresponding equations to Atkinson's (pressure loss) for headloss and workloss were derived. The thermodynamic weight relational resistance ([w] s2/m5) associated with energy per unit weight (headloss) was dimensionalized for the first time. Also, normalized Atkinson-like equations for headlosses and worklosses were derived to ease direct computations in mine ventilation practice.

Jan 1, 1995

By Sidney A. Hiscock

INTRODUCTION Lead and zinc are today rightly regarded as sister metals. Historically, however, they differ markedly with lead being known and in general use as the metal since 3000 BC in several countries which at that time might have been described as mature economies. Zinc was not isolated and recognised as an industrial metal with distinct and valuable properties until about 1700-1800 AD (although it had, of course, been utilised as a constituent of brass for some 2000 years previously). c were well established as industrial metals by the beginning of the 20th century. The present paper briefly reviews the overall growth in world consumption* and changes in the three main areas which today represent the mature economies or industrialised areas, i. e. ,Europe, the United States and Japan. Trends in overall consumption are determined by the demands for the individual uses for lead and zinc. The changes in patterns of use in the industrialised areas - individually and collectively - and reasons for the changes are also considered. LONG TERM TRENDS - 1900-1984 The World Picture Since the beginning of the 20th century the world consumption of lead (3.9 million tonnes in 1984) has grown almost fourfold and that of zinc (4.7 million tonnes in 1984) is almost eleven times greater than it was in 1900. The long-term trend has been one of continuing expansion for both. metals although the pattern has been severely disturbed at certain periods, for example in the years immediately following the two world wars and at times of marked recessions in industrialised areas. Apart from such major setbacks, new levels of consumption have been established regularly every few years. Recently, however, consumption has not really grown and with only a slow and partial recovery in world industrial activity at present, there is no indication that the peak consumptions of 4.2 million tonnes of lead, set in 1979, and 4.8 million tonnes of zinc (1973) will be exceeded in the near future. The growth in world lead and zinc consumption since 1900 is shown in Figure 1 (which includes changes in copper and aluminium for comparison). Overall growth over the period 1900-1984 has been about two percent a year for lead and about three percent for zinc (annual growth for copper has also been about three percent). Increases in tonnage consumption and growth rates by decade for lead and zinc are summarised in Table I. However, the growth rates by decade sometimes conceal very large individual annual increases and decreases. For example, in 1975 lead consumption fell by 13 percent and zinc consumption by 22 percent compared to 1974. In 1976 consumption of lead and zinc rose by 12 percent and 18 percent respectively. The years when consumption 'landmarks' (ie one, two, three and four million tonnes) were first reached are shown on Table 2. Clearly, the pattern of shorter periods being required to attain each extra million tonnes of consumption was broken in the 1970's. The consumption of zinc overtook that of lead for the first time in 1940, and since 1946 has always been at a higher level. Trends in industrialised areas The two key industrialised areas at the beginning of the 20th century were Europe and the United States which between them accounted for some 95 percent of world lead consumption and 98 percent of zinc consumption. Figures 2 and 3 show the growth in lead and zinc consumption, and Figures 4 and 5 the percentage shares for each area since 1900. Europe has usually been the major user of lead except for some years in the 1920fs, most of the 40's and early 50's when consumption in the United States was larger. In 1900, Europe accounted for about 64 percent of world lead consumption and the United States just over 30 percent. Currently, Europe takes about 40 percent of world consumption and the

Jan 1, 1986

By Jerry L. Fuller

Fan performance graphs are generated by digital computer using two programs, RUN- FANS and FANPLOT. RUNFANS calculates fan performance data from stored specific-volume, specific-speed data for a given fan type with appropriate allowances for fan diameter, rotational speed and air density. FANPLOT accepts specifications for drawing the graph and accepts either user-supplied pressure-quantity data or RUNFANS- calculated data as input, Operational procedures for both programs are detailed and examples of their interactive query routines are included. The hardware necessary to generate the graphs is illustrated. Several hardcopy output options are discussed,

Jan 1, 1984

By A. Kaczmarek

As the mining industry is enjoying a much needed and long awaited increase in demand for natural resources, consolidations in both the mining and mining service industries and a generational departure of experienced industry professionals is challenging today’s mining companies, not only in maintaining their existing operations, but also in securing qualified resources for developing new projects. These challenges are compounded for junior mining companies, oftentimes lacking in operating properties to draw from for experienced professionals and having to compete with the majors’ “mega-projects” for experienced project personnel from the reduced ranks of engineering companies. This paper discusses some strategies developed by Anatolia Minerals Development Limited in developing its Çöpler Gold Project in central Turkey.

Jan 1, 2006

By R. K. McFarland, E. S. Diamant, L. Blake

A number of concepts for basing strategic missiles facilities deep underground have been developed within the defense industry. Recently, several contracts were let by the Air Force Ballistic Missile Organization to better develop system concepts for Deep Basing and Rapid Egress of Missiles from these facilities. A particular challenge of the Deep Basing Concept is the need for the excavation of egress tunnels or shaft from the deeply based facility to the ground surface, in a rapid and reliable manner. This Paper describes a conceptual MX-Deep Basing Facility, the technical issues associated with its design and construction, and potential means for achieving rapid egress from this facility. Manuscript not received in time for publication.

Jan 1, 1983