Search Documents

By Richard L. Ash

In many instances, blasting exerts the dominant control over the economics and safety of excavation, where the materials involved are too hard and tough to be fragmented efficiently by other means. However, associated with the fragmentation process other effects very often result that are not desirable and may even be hazardous, such as fly rock, air blast, excessive overbreak, and damaging ground virbrations. It has always been the desire of those concerned with blasting to better control the forces involved so as to improve the breakage of materials, but at the same time reduce, or eliminate if possible, the unwanted side effects. Until the last decade or two, little was known of the phenomena concerned with blasting. However, since that time many investigators have studied blast mechanisms produced from both chemical and nuclear explosions, with the result that general concepts of the principles have been developed. But, in general, it is assumed that the energy from the explosion would be propagated spherically throughout the material, the latter of which for convenience of analyses is considered homogeneous and isotropic, i.e., the properties are the same in all directions, However, rocks are not isotropic as a rule, and evidence clearly indicates blasting forces rarely function uniformly or in spherical form as theorized.

Jan 1, 1965

By Michael Gauna

A high seam geologic condition exists at Jim Walter Resources No.4 mine which requires immediate rib support after a continuous miner cuts a place, High seam mining heights are typically 2.4 to 2.6 m (8 to 9 it) and a thick rock layer is present in the upper portion of the coal rib side. The 610 m (2000 ft) mining depth at No. 4 mine induces horizontal rib line movement after excavating an entry. Horizontal rib movement greater than 30.5 cm (12 in) have been noted. When lateral movement occurs in the high seam areas, the thick rock layer, and the coal above the rock layer, become fractured and tend to roll into the entry. If not adequately supported, large rib rolls develop in the place being bolted as well as in previously mined areas which endanger men and equipment. To control this situation rib support must be installed in the roof bolting operation as the bolting crew works towards the face. A rib control system has been developed for this high seam mining condition utilizing a mechanical anchor bolt placed at an angle in the rib and installed with a modified Fletcher DDFI- 15 bolting machine. Over 120 km (75 mi) of entry have been supported with angle rib bolts. These angle bolts constitute 43 to 60% of the total roof and rib bolt footage in the high seam port- ions of No.4 mine. The angle rib bolting system has proven safer, more effective, and more efficient than the earlier support method employing bolts installed horizontally into the rib. No rib roll accidents have occurred since the angle drill bolting machines were placed in service in 1981. By securing the broken rib material with an angle bolt anchored above the coal pillar, a more effective means of rib control is achieved. Angle rib bolting does not interfere with continuous miner productivity. In addition, bolting crews are now reduced from three to two people and the total drilling supply costs are approximately 60% the previous cost, when compared to the previous support method using horizontal rib bolts.

Jan 1, 1983

By A. W. Storm

Vertical shaft furnace design and operation have their roots deep in antiquity. There is substantial evidence to indicate that iron was reduced from its oxides to serve mankind's needs long before recorded civilization - - actually prior to 3500 B .C. For at least 5500 years man has been matching wits with Nature to find better methods of extracting this most common, yet essential, metal from her, grasp. And, during nearly all of this period, the vertical shaft furnace has played a principle role in this dramatic struggle.

Jan 1, 1962

By G. Stephan Derrickson

Any type of agitation within a confined vessel is primarily concerned with two parameters: 1) A level of agitation describing the homogeneity of the constituents (whether it be suspension or mixing) and, 2) the energy efficiency with which this level of agitation is accomplished. The following is an attempt to present a solution to the problem of adequately defining and optimizing these properties. First included is a discussion of the application of good design practices to the determination of a mechanically efficient shape to the blade elements of the propeller. These practices, excluding several appropriate modifications, have been known, but not well understood, in aircraft fluid mechanics for a number of years. Secondly, having optimized the direct impartation of energy to the medium being agitated, attention is turned to one of the more perplexing phenomena of multi-phase systems - definition and prediction of agitation levels. The result of recent study and testing is a method of scaling which the authors feel provides a lucid understanding of governing physical parameters within the agitator itself, allowing one to scale up and down with confidence.

Jan 1, 1982

By Patrick McElhinney, Jacob Carr, Bruce Whisner, Cory DeGennaro, Jingcheng Li

Since 2016, electromagnetic interference (EMI) of personal dust monitors (PDMs) with magnetic proximity detection systems (PDSs) has been observed in underground coal mines. The EMI causes the magnetic field measurements of a PDS to change, which, in turn, alters the calculated location of the miner relative to the machine. Any altered location calculation can potentially cause the PDS to fail to warn a worker who is at an unsafe distance from the machine, arousing a serious concern on safety hazard caused by EMI in underground mines. The search for EMI mitigation strategies led to the development and use of large shielding pouches and boxes to hold the entire PDM to reduce its magnetic emission. Research on these pouches and boxes found that although they were able to reduce the emitted radiation from the PDM, they also disturbed the magnetic field of the PDS, affecting its performance. Researchers from the National Institute for Occupational Safety and Health (NIOSH) have focused on shielding internal PDM components rather than shielding the entire PDM. The PDM air pump motor is one of the PDM components that has been identified as a major source of electromagnetic radiation and has been selected for further study and tests. The measurements show that a small copper or aluminum foil enclosure can effectively reduce the magnetic emission of the motor by between 50 and 85% at 73 kHz. This study compares the test results of the air pump motor with various cost-effective shielding materials. The data provided in this paper can serve as a reference for shielding enclosure design of the PDM air pump motor to reduce its electromagnetic emission as one form of EMI mitigation strategy.

The Penetrating Cone Fracture (PCF) technology 1 is a new method of rock excavation developed by Sunburst Excavation, Inc. of Denver, Colorado. PCF is a rock excavation method which employs tensile breakage mechanisms under controlled conditions to enable the continuous excavation of rock?in underground and some surface applications. The technology has developed rapidly over the last two years to the point where it is now being prepared for commercial application in the mining and civil construction industries. The initial commercial application of PCF will be undertaken at the Perseverance Nickel Mine of Western Mining Corporation Limited in Western Australia beginning in May, 1994.

Jan 1, 1994

By J. Gibson

"INTRODUCTION As one of the most pressing and important political debates of this century, climate change has captured global attention and is forcing governments to take action towards decreasing GHG and carbon emission levels below what was previously thought to be necessary. With the ever-increasing price of diesel fuel accompanied by the popular topic of carbon taxes and greenhouse gas emissions, the mining industry is looking to industry specialists for assistance. The benefits of a no-idle policy reach far beyond carbon reduction and fuel savings, ranging from decreased maintenance to increased engine life. With products like battery powered A/C systems and diesel-fired heaters, going no-idle is easier today than ever before. With both systems being manufactured to withstand the harsh environments of the mining industry, the end user will see a seamless change from conventional, inefficient belt-driven systems to future, stand-alone mobile equipment HVAC. THE HISTORY OF GHGS AND CLIMATE CHANGE In 1896 Svante Arrhenius first claimed that the combustion of fossil fuels may eventually result in enhanced global warming, but not until 1955 did Gilbert Plass draw global attention to global warming by summarizing that adding carbon dioxide to the atmosphere would intercept infrared radiation and thus warm the earth. Then in the early 1960’s Charles Keeling developed modern technology to produce concentration curves for atmospheric CO2 (Figure 1). In 1988 the Intergovernmental Panel on Climate Change (IPCC) was founded by the United Nations after acknowledgement of a rising global annual temperature. The IPCC consists of over 2500 scientific and technical experts from more than 60 countries, and because climate change could not be solved by a single country, the Kyoto Protocol was negotiated in 1998 requiring all participating countries to reduce their GHG emissions by at least 5% from the 1990 levels. The Protocol was signed by 186 countries in 2001 (since then several countries have retreated from the agreement, including the United States)."

Jan 1, 2015

By H. Verakis, M. J. Sapko

The Pittsburgh Research Laboratory (PRL)1 of the National Institute for Occupational Safety and Health (NIOSH) in collaboration with the Mine Safety and Health Administration (MSHA) Technical Support Center has devised a prototype hand-held instrument which can provide a direct assessment of the potential explosibility of a coal and rock dust mixture. Current Federal regulations require that rock dust be applied in all underground areas of a coal mine to mitigate the propagation of a coal dust explosion. To determine compliance with the Federal regulation, mine inspectors collect dust samples from sections of underground coal mines for an MSHA laboratory analysis of incombustible content. However, the laboratory analysis may not be completed for more than a week or two, during which time the mine area from which samples are taken may be inadequately protected. The operation of the Coal Dust Explosibility Meter (CDEM) is based on the difference in optical reflectance between light rock dust and dark coal dust. For a given coal volatility, the optical reflectance of such mixtures is relatively constant at the limit of explosibility, independent of the coal dust particle size. The CDEM is not intended to replace the current MSHA laboratory analysis of coal mine dust samples for incombustible content, but to serve as a supplemental device for enhancing mine safety through improved rock dusting practices.

Jan 1, 2006

By J. Andrew McGlenn, Brian McInnes, Bruce Downing, Murray Gant

The Second Narrows Water Supply Tunnel crossing beneath Burrard Inlet is an important component of the Greater Vancouver Water District’s plans to increase seismic resilience and meet increasing water demands. The project included the 110-meterdeep (350 ft) South TBM Receival Shaft, one of the deepest shafts to date in the sedimentary rock unit underlying much of Metro Vancouver. The shaft encountered varied sedimentary rock types, including fractured rock, with accompanying high groundwater inflows. This paper discusses the design and construction challenges associated with this shaft and the necessary means to complete the shaft in time for TBM arrival.

Jun 13, 2023

By DeVerle Harris

The enthusiasm with which individuals have participated in mineral exploration in the development of this country testifies to the fact that there was once a very real probability of making a worthwhile discovery. Over the years, the discovery and subsequent exploitation of the accessible ore deposits have made the finding of new deposits progressively more difficult. Present day mineral exploration has evolved from the lone prospector with the grubstaker behind him to a very costly and complex business, involving large sums of money and a staff of experts in the fields of exploration technology. Exploration today must be carried out on a large scale to be profitable. With the involvement of large amounts of capital, there has been a good deal of interest in methods of optimization of the allocation of the resources of a firm 'engaged in mineral exploration. As a step toward this, mathematical models have been formulated which are designed to quantify those variables of mineral exploration in such a manner that they can be integrated with all phases of the firms operations so as to optimize its profit objective or more simply, to make exploration more efficient and effective.

Jan 1, 1964

By Rameshwar Sah, Bharath Kumar Shanmugam, Govinda Raj Mandela, Marutiram Kaza, Harsha Vardhan, Harish Hanumanthappa

Iron ores obtained from different sources differ in their chemical and physical properties. These variations make the process of grinding a difficult task. The work carried out in this context focuses on three different samples of iron ore, viz., high silica high alumina, low silica high alumina, and low silica low alumina. The grinding process for all the three iron ores is carried out individually in Bond’s ball mill and the total retention time taken by each iron ore sample is calculated. The present investigation focuses on utilizing the calculated retention time of the iron ore as a standard grinding reference time to the laboratory ball mill for optimizing the grinding time of each ore. The desired P80 (150 μm) with an acceptable range of hematite liberation (> 75%) was obtained in the laboratory ball mill after reducing 6 min from the total retention time taken in the Bond ball mill.

By Charlie Watts, Ken Smales, Ron Fleming

The Manapouri Power Station is an underground hydro-electric station located in the South Island of New Zealand, and was constructed in the 1960s. Between 1997and 2002, a second 10m diameter tailrace tunnel was constructed to increase the out-put and to improve the overall hydraulic efficiency and output of the station. A critical economic and project approval consideration for the second tunnel was the outage time required for the breakthrough into the power station. The power station is in part dedicated to providing power to an aluminum smelter with the balance to the National Grid, and apart from the physical problems associated with providing an alter-native power supply to the smelter, the loss of generation revenue and supply risk were significant issues. Innovative planning reduced the planned outage time from several months to21 days, and the breakthrough was eventually achieved in 11 days as a result of additional value engineering measures implemented during construction. This paper describes the engineering optimization that took place during the planning stages of the project and later during construction, as well as describing the construction methodology used.

Jan 1, 2007

By W. G. Willson

Low-rank coal (LRC) drying processes are generally categorized by operating temperature, drying environment and type of feed (either sized or ground coal). Within these broad categories, drying processes differ according to the type of drying equipment and methods of quenching and stabilizing the dried products. This paper focuses on the produce quality of various LRC drying processes including conventional low and high temperature evaporative drying and non-evaporative, hydrothermal drying. The former may be preferred if the dried product can be utilized immediately, but moisture re-absorption, spontaneous heating and fines production during handling are problems associated with longer term storage, transportation and utilization. Methods for reducing these problems are discussed. Hydrothermal processing is an advanced technology featuring high pressure, non-evaporative drying, which solves stability problems by producing a liquid fuel.

Jan 1, 1997

Despite limited discussion, Chemistry of Flotation is a good text and reference 1985 by M. C. Fuerstenau, J. D. Miller, and M. C. Kuhn Society of Mining Engineers Caller No. D Littleton, CO 80127 Softcover, $23.50 (member), $18.50 (student member), $28.50 (list) Review by Richard R. Klimpel Chemistry in Flotation, as stated by the authors, is intended as a textbook for students as well as a reference book for practicing flotation engineers. It covers subject matter related to surface phenomena; collectors and collector salts; natural floatability; the flotation of sulfide minerals, insoluble oxide and silicate minerals, semisoluble salts, and soluble salts; and slime coatings. There are no discussions in the book on practical plant implications of flotation chemistry, such as the influence of rate, particle size effects, dosage, flotation equipment, and methods of chemical addition. The book itself is small (only 177 pages), and, as published, is in an easy-to-handle soft cover. Once one accepts the intent of the authors, this book really does represent a very concise and convenient summary of the chemistry of flotation. It is, however, far from complete in its discussion of concepts and implications of data. Very often in the presentation, key prior knowledge (or at least subject matter awareness) not given in the book, is assumed. Thus, depending on one's familiarity with the specific subject matter, some sections can be easily followed while others could be tough going. Some of the discussion is so brief and terse on important subjects that unless the reader already realizes the meaning of the presentation, the conclusions to be drawn are not always clear. Therefore, if one is not expecting a self-contained primer on flotation chemistry, this book is very useful. To this end, the book is recommended to practitioners of flotation chemistry. The presentation of data in figures and tables is good. It helps considerably in the book achieving its conciseness. The authors certainly are qualified and knowledgeable in the subject matter - apparent in the style of presentation. In summary, this reviewer thoroughly enjoyed this book and will use it as a concise review of flotation chemistry. Richard R. Klimpel, member SME, is a scientist with Dow Chemical Co., Discovery Development, 1776 Building, M. E. Pruitt Research Center, Midland, MI 48640. International Symposium on Blast Furnace Ironmaking, 1985, The Indian Institute of Metals, The Tata Iron and Steel Co., Ltd., Jamshedpur 831007, India, 282 pp., papercover, no price given - Papers from this symposium held in Jamshedpur, India, include the following: determination of coal and coke quality; feed to blast furnaces; burden quality and blast furnace performance; operation of blast furnaces on charcoal; review of cast house slag granulation systems; developments in blast furnace engineering and control; process improvements in blast furnace ironmaking; coal injection into the blast furnace; and coke from stamp charged coal. Advances in Materials Technology for the Process Industries, 1985, edited by H.A. Huskins, National Association of Corrosion Engineers, P.O. Box 218340, Houston, TX 77218, 273 pp., softcover, $20-This book is the proceedings of a meeting held in Atlanta, GA in October 1984. It describes innovations in metallurgy, ceramics, glass, composites, and polymeric materials that impact the integrity and economics of operating systems. It covers biotechnical developments, improvements in membrane systems, or beneficiation processes, as well as developments in electrochemical controls, testing procedures, and surveillance techniques. A Reference Guide to Mining Legislation in Canada, 1985, by B. Barton, B. Roulston, and N. Strantz, The Canadian Institute of Resources Law, Room 430, Bio Sciences Building, The University of Calgary, Calgary, Alberta, Canada T2N 1N4, 120 pp., bound, $US28- This guide provides a ready means of finding how the different jurisdictions in Canada regulate mineral activity. It covers the rights required for exploration, development, and production of mineral metallics and industrial minerals. It does not cover placer mining, petroleum and natural gas, bituminuous sands, coal, or structural materials. Dictionary of Geological Terms, 1985, edited by Robert L. Bates and Julia A. Jackson, The American Geological Institute, 4220 King St., Alexandria, VA 22302, papercover, $7.95 plus $1 for postage - This third edition is for geoscience students, teachers, and rockhounds. It defines the core vocabulary of earth sciences, contains 8000 revised definitions, and includes 1000 new terms. It adds recent terms in plate tectonics, hydrology, and permafrost studies. Accurate definitions are given without technical jargon, cross-references are included, and commonly used abbreviations are provided. Processing and Utilization of High Sulfur Coals, 1985, edited by Yosry A. Attia, Elsevier Science Publishing Co. Inc., 52 Vanderbilt Ave., New York, NY 10017, 787 pp., bound, $142.50-These proceedings comprise the majority of the papers presented at the First International conference. Investigators there reported the latest discoveries, developments in commercial practice, and state-of-the-art reviews of scientific principles and applications of various technologies for handling, processing, and use of high sulfur coals. Sessions were held on: characterization of sulfur in coals; environmental problems and impact of high sulfur on coal use; selective mining and blending; coal desulfurization by physical and chemical cleaning techniques; handling of coal fines; sulfur capture during coal combustion; biological desulfurization of coal; and new applications for high sulfur coal. The Economics of Magnesium Metal, 1985, Roskill Information Services Ltd., 2 Clapham Road, London SW9 OJA England, 129 pp., 71 tables, appendices, bound, $750-Despite setbacks in some major magnesium markets in 1985, Roskill's latest forecast for the last half of this decade is for a 4% to 6% annual growth rate in demand. Growth for magnesium metal is expected in the motor industry for use as a possible substitute for aluminum. Some magnesium producers are altering their marketing strategies to cultivate this market. This study also includes a review of the worldwide magnesium industry, its end uses and consumption, and international trade and price trends.

Jan 7, 1986

By Zefang ChenLi, Laijun Ma, Lei Mao, Fang Lian

"In our work, the preparation technique of high pure manganese sulfate directly from low-grade rhodochrosite ore (MnCO3) was studied and improved intensively, including the effective leaching process and the short purifying process. Based on the same ion effect, the repeated leaching of rhodochrosite with sulfuric acid is proposed to improve the solubility of Mn2+ and inhibit the dissolution of the impurities Ca2+ and Mg2+. Moreover, the repeated leaching process could make full use of rhodochrosite and lower the dosage of sulfuric acidas raw material. With the aid of theoretical calculation, Ba(OH)2 was chose to adjust the pH value of manganese sulfate solution, and BaF2 to remove Ca2+ and Mg2+completely in the process of purifying. The results demonstrate that the extraction ratio and the recovery ratio of manganese reached 94.3% and 92.7%, respectively, which shows the prospect of industrial application. In manganese sulfate production, the heavy metal impurities have been decreased to less than 1ppm. Moreover, the content of calcium, magnesium and sodium has been decreased to less than 20ppm, which meets the standards of high pure reagent for energy and electronic materials. Our study enlightens an approach to the sustainable application of low-grade rhodochrosite.Introduction Low-grade manganese carbonate ores (=14%) becomes gradually the main resources for exploitation and applications in China according to national mineral resources survey (Tan et al 2004 and Singh et al 2017). Therefore, the electrolytic deposition technique of rhodochrosite faces great challenges including low electrolysis efficiency, high-resource input and high-pollution discharge (Fu et al 2010, Michelis et al 2009, Zhang et al 2013). Recently, more and more amount of manganese series with high or super high purity such as MnSO4, MnO2, Mn3O4 and MnO is demanded with the development of energy and electronic materials. Due to low-grade ores containing multiple elements such as iron, silicon, calcium and magnesium, conventional preparation of manganese sulphate with high purity from electrolytic product is characterized by long production-cycle and high-energy consumption (Subrat et al 2011, Mpho et al 2013). By contrast, hydrometallurgical method combined with thermal decomposition, hydrothermal synthesis and sol-gel processes has been widely studied because of its high efficiency, low consumption and low cost (Chen et al 2008). But the key problem in direct preparation of manganese series form low-grade rhodochrosite is to remove completely the multiple impurities such as iron, silicon, calcium and magnesium (Liu et al 2014). So it is urgent to develop a sustainable alternative approach with character of short process, high efficiency and environmental friendly."

Jan 1, 2017

By R. Wild

[When a blast furnace has a certain defined burden and is operated under fixed conditions of blast temperature, etc., the fuel efficiency is determined by the extent to which the reducing gases can remove oxygen from the burden in the furnace stack. This is determined by two distinct factors: 1) The uniformity of gas-solid contact, and 2) The ease with which oxygen can be removed from individual pieces of burden. This latter is often called burden reducibility. When burdens were poorly prepared the first factor was by far the most important and a study of the reducibility of individual lumps was of rather academic interest recent years good burden preparation with emphasis on sized material has led to greatly improved gas distribution in the stack, and thus the second factor has become much more important and there has been a marked increase in interest in methods of measuring reducibility.]

Jan 1, 1964

"Replacing the century old rail tunnels that run beneath the Hudson River and carry about 200,000 passengers per day between New York to New Jersey has been a high priority for many years. But after Superstorm Sandy hit the east coast of the United States in 2012, the urgency to replace the tunnels increased dramatically. The Hudson Tunnels project is one of nine projects that make up the larger $30 billion Gateway Project. The Gateway Project has been called the most urgent infrastructure program in the country and the Hudson Tunnels is the most critical part of the project, as it will build a new rail tunnel under the Hudson River and rebuild the existing and deteriorating North River Tunnel that connects New York and New Jersey.“Superstorm Sandy proved the level of resiliency of the tunnels, which was not very good,” Amtrak deputy chief engineer structures James Richter told attendees of the George A. Fox Conference in New York City on Jan. 23. Age and corrosive salts deposited by flood waters from the storm in 2012 have affected interior concrete and copper wiring in the tunnels. “Since then, things have been deteriorating and getting less reliable.”Richter, along with Mohammed Nasim, senior director engineering design, both with Amtrak, spoke at the 2018 George A. Fox Conference where more than 350 tunneling and underground construction professionals attended the conference at the Graduate Center of the City University if New York to share insights about the complexities many of them face on daily basis.Under the theme of “Managing construction of complex underground projects: Strategies for tunneling in populated areas,” the one-day conference featured presentations from some of the top minds in the tunneling and underground construction industry. The presentations touched on everything from the highly technical challenges of constructing tunnels through changing geology while working beneath cities and rivers, to navigating the complex financial issues and contracts that come with the projects that have many stakeholders.All of those challenges, and more are part of the Hudson Tunnels project. It is one of the best examples of the full complexities of a complex tunnel project, with the added pressure of securing funding from state and federal government entities under an increasingly tight deadline."

Jan 3, 2018

By Robert S. Lehto

Zinc concentrates received in La Oroya zinc refinery are marmatitic in nature, contain about 11% iron and traces of other metal values, Figure 1 shows the zinc circuit. The calcine from the roasted concentrates is leached in spent zinc electrolyte. Major part of the impurities is iron which has been oxidized to its trivalent form, This is the origin of the zinc leach residue for which the ZILERET process was developed and so named. The impure liquor from the leach is sent for purification and thence to electrolysis- zinc deposits on aluminum cathodes from which: it is stripped, melted and cast into slabs Typical assays of zinc calcine and leach residue are given in Table 1. Metal values contained in the leach residue, without counting any value of iron, amount to roughly $130 per short ton.

Jan 1, 1969

By Jessica M. Wempen, William G. Pariseau, Dallan J. Coons, Michael K. McCarter, Erik C. Westman

The abstract discusses the importance of proper pillar sizing in underground mining for safety and efficiency. It highlights the use of theoretical models, geotechnical measurements, and numerical modeling in predicting pillar behavior. The research focuses on using seismic tomography to image stress changes in a yield pillar at a longwall mine as the longwall face approaches. The study aims to compare the stress distribution imaged using tomography with theoretical models, geotechnical measurements, and numerical models.

Mar 18, 2022

By M. Yavuz

Due to workability difficulties, people have begun to use iron ore much later than gold, copper and bronze. In addition, iron and steel products are the most commonly used metals which are necessary for human life today. It is a fact that iron ore is raw material of the steel production process as known. Iron&Steel sector is plays an important role in the economic development of countries all over the world. Therefore, the amount of production and consumption of steel is one of the basic indicators of industrialization all over the world. The amount of steel consumed per capita of the country is considered as a measure of development. The world average per capita consumption of steel is around 210 kg in 2007 (Yildiz, 2009).

Jan 1, 2010