Search Documents

By K. Huttu, A. van Wageningen

"The Kittilä underground mine in northern Finland is extracting one of the largest known gold deposits in Europe. Kittilä achieved commercial production on May 1, 2009, becoming Agnico Eagle’s first mine to open outside of Canada. The Kittilä orebodies were initially mined from two openpits – Suuri and Roura – and underground operations were added in October 2010. The pits were mined out in November 2012, so mining is now entirely underground in the Suuri and Roura deposits. Additional, small openpits will mine any remaining near-surface reserves in the future.The Kittilä Mine is located in the Lapland region of northern Finland, approximately 900 km (560 miles) north of Helsinki and 150 km (93 miles) north of the Arctic Circle. With a mine life estimated through 2034, Kittilä is Agnico’s longest-life mine.The mine’s proven and probable reserves contain 32 Mt (4.7 million oz) at 4.6 g/t (0.13 oz/ st) gold. Ore has been mined from underground since 2010. The original 3 kt/d (3,300 stpd) operation underwent an expansion project to increase the throughput capacity of the mill by 1 kt/d (1,100 stpd), starting by the end of 2014.The region around the Kittilä Mine is underlain by mafic volcanic and sedimentary rocks of the Kittilä Greenstone Belt oriented nearly vertical. This greenstone belt is similar to those hosting Agnico Eagle’s Canadian deposits in Quebec’s Abitibi region and Nunavut. At the contact point between ironrich and magnesium-rich rocks lies a 100- to 200- m (330- to 660-ft) thick structural zone known as the Suurikuusikko Trend. This trend hosts the Kittilä deposit, where multiple mineralized zones have been traced over a strike length of more than 25 km (15 miles).Most of Agnico Eagle’s work has focused on a 4.5-km (2-mile) segment of the Suurikuusikko Trend that hosts the five main zones of the known gold reserves and resources. From south to north they are: Ketola, Etela, Suuri, Roura and Rimpi.The ore at the Kittilä Mine is refractory, making gold extraction relatively difficult because the gold is generally locked inside the two main sulfide minerals – arsenopyrite and arsenic-rich pyrite. Only about 4 percent is very fine-grained “free gold” (not locked in sulfide grains) and easier to extract. Most of this free gold is found in the outer, oxidized or eroded sections of the ore."

Jan 1, 2015

By Steve Kral

The third edition of the Underground Construction Association of SME?s (UCA) Cut-ting Edge series of conferences focused on a challenge every underground construction and tunneling project faces: controlling ground water. The conference, held in New York City in November, is a partnership between the UCA and The North American Tunneling Journal. It featured more than 20 technical presentations by professionals from around the world. Each described specific challenges unique to their projects and the solutions employed. More than 175 professionals attended the two-day conference that included an exhibition featuring 17 companies. In addition to the technical program, the Cutting Edge conference featured a site visit to the $10.4 billion East Side Access Project. Sponsors of the meeting included Soil Freeze, Traylor Bros., Kiewit, Skanska, Moretrench, Aecom and The Robbins Co.

By Paloma Lazaro, Moe Momayez

Heat-related illnesses (HRI) are relatively common in both hot surface and underground mining operations. When workers are exposed to extreme heat or strenuous work in a hot environment, they become prone to heat stress. Heat strain is the result of the body’s response to external and internal heat stress. It is therefore vital for the conditions leading to heat strain be detected and treated in a timely manner. Heat-related illnesses are manifested by exhaustion and heat stroke. The predicted heat strain (PHS) [ISO 7933 (2004)] model has been developed to predict the health condition of the worker in terms of core body temperature and water loss. The PHS model tested in this study is based on eight physical parameters that are measured at different intervals during a work shift. They include air temperature, humidity, radiation, air velocity, metabolic rate, clothing insulation, posture, and acclimatization. The model predictions are then compared with a direct physiological measurement, such as core body temperature. We present the results of an extensive study that monitored and predicted body’s response to heat stress under different environmental and working conditions. The PHS model provided reliable results in most instances in comparison with other prediction methods currently in use in the field.

By J. S. Gardner

Fortunately, few mining professionals have dealt with what all mining professionals fear---a mine disaster. Unfortunately, many have dealt with ?accidents? which may or may not claim lives but nevertheless rise to the level of a ?disaster? given the fallout of liability and litigation in today?s society.1 The undersigned authors published an article some ten years ago regarding crisis management2 based upon their collective first-hand experiences in actual disasters to that point in history. Unfortunately, disasters have occurred since that time, prompting legislation, and a fresh analysis and expansion of those basic principles is certainly in order. Without question, no two disasters are ever alike, yet general guidelines for forming an effective plan of action can be formulated?and if a mining operation is to have any chance of survival after a disaster, such a plan is vital. The primary concern as any disaster evolves remains as stated a 2003 SME article3--the protection of human life. From that point, the focus moves to any assistance that may be needed given the magnitude of the situation. Permeating throughout this process is "damage control." The first step in dealing with a disaster, however, begins long before any threat of danger arises?formulation and implementation of an Emergency Response Plan.

Feb 23, 2014

By Warren E. Fife

This paper will discuss the application of a continuous miner using a fixed drum milling type cutting head for the underground mining of hard rock and salt ores. Continuous mining machines of the ripper chain cutting head, oscillating milling cutting head and boring arm designs have been used in rock and salt applications with various degrees of success. The large boring arm miners have been successful in potash, trona and salt, but they have not been successful in mining rock materials like iron ore. The main method used in underground mining rock materials is the conventional drilling and blasting the ore from the solid. This is particularly true for the harder, more abrasive copper and iron bearing ores. The softer salt based ores of potash, trona and rock salt can use several underground mining methods depending on seam conditions. Several of these methods use underground coal mining equipment that has been extensively redesigned to adapt it for use in mining noncoal materials. Conventional mining methods employ the use of a universal cutting machine to undercut or topcut the ore body before face drilling and blasting takes place to produce a smooth parting of the ore. The boring arm continuous miner is widely used in underground mining of potash and trona ores. It produces a tunnel with a smooth semicircular contour which results in good rib and roof stability. The ripper chain continuous miner is also widely used in mining the salt based ores of potash, trona and rock salt. They are used more frequently in Europe than in the United States and Canada. Some reasons for using the mechanical mining machines as opposed to the conventional drilling and blasting techniques for mining hard rock ore bodies are the resulting improved rib and roof control, facilitates selective mining of the ore body, and requires less man-

Jan 1, 1974

By M. Laliberte

"Gold-mine effluents are often characterized by high concentrations of copper, ammonia and cyanide derivatives (mostly cyanates and thiocyanates). While not acutely toxic to birds, this water can be acutely toxic to fishes and invertebrates. In many jurisdictions, the effluent requires further treatment in order to pass a mandatory requirement to be nonlethal to species like the rainbow trout (Oncorhynchus mykiss) or Daphnia magna. Using actual mine water, it has been demonstrated that aerated moving bed biofilm reactors will biodegrade the ammonia, cyanides, cyanates and thiocyanates, thereby removing the toxicity associated with these components. By removing copper by precipitation the water can be made to pass acute toxicity tests. Tests have demonstrated that the process is stable between 4 and 25°C, with no significant changes in the treated water composition. Once the biomass is acclimatized, the process is resistant to upsets and requires very little inputs except for phosphorus and air. Furthermore, it has been demonstrated that an anoxic reactor can be added downstream of the aerated reactors to remove nitrates if required.IntroductionThis paper will demonstrate that gold-mine effluents, which are toxic to fishes and invertebrates, can be made nontoxic by using a combination of chemical precipitation and biological oxidation.The typical composition of gold-mine effluents will first be described. The applicable legislation will then be introduced, with its requirement that the treated effluent be nontoxic. The toxicity of a typical untreated effluent will then be confirmed, and the sources of the toxicity identified. After that, a number of toxicity reduction treatment methods will be presented, and the selected method will be described.The lab tests that confirmed the efficiency of the treatment method will be presented, with three phases of testing as the understanding of the process gradually improved. Toxicity test results showing that the water is nontoxic after treatment through the temperature range will be presented."

Jan 1, 2015

By A. S. Ibrado

Research investigations on the chemistry of the adsorption of gold cyanide on activated carbon have mostly reduced the role of activated carbon as the provider of the large surface area needed for adsorption. Most do not go beyond suggesting that oxygen functional groups on carbon play a key role in the adsorption process. Our research shows that the nature of the material, specifically its structure, is a crucial factor in the adsorption equation. To delineate the effect of adsorbent properties, gold cyanide was adsorbed on a series of carbonaceous adsorbents, including lignite, coals, anthracites, carbon blacks, graphite and activated carbon, which covers wide variations of composition, surface acid group content, and degree of graphitization. The results show that the adsorption of gold cyanide per unit area of adsorbent is not related to the amount of oxygen groups on the surface or even the total oxygen content of the material. However, they show very strong correlation with the degree of graphitization of the adsorbent, which indicates that the graphitic plates of activated carbon play the most important role. The findings suggest that majority of the adsorption occurs on the plate faces of the graphite crystallites of activated carbon.

Jan 1, 1992

By T. Hayes

Track-type tractors remain one of the most cost-efficient stripping tools available to coal miners. Whether they are "sweetening up" a dragline operation with pre-benching or serving as the primary stripping tool, dozers can play an important role in driving down mining costs. This paper reviews the application zone of track-type tractors. In addition, it provides tips on site set-up, equipping of tractors, and machine operation which the audience can take home and apply.

Jan 1, 1996

By R. David Williams

Old mine workings are found throughout the Western United Sates on lands administered by the U.S. Bureau of Land Management (BLM), U.S. Forest Service (USFS) and private lands. Some of these mine workings date back to the late 1800s. There may be as many as 100,000 sites on lands administered by the U.S. Forest Service and Bureau of Land Management. The Bureau of Land Management has worked with the State of Montana and other agencies to identify and prioritize these sites on BLM administered lands. Following completion of the AML inventory work, the Bureau began an aggressive program to clean up priority sites. This presentation will highlight completed work as well as work in progress on several sites.

Jan 1, 2000

By V. Králová

The TESCAN Integrated Mineral Analyzer (TIMA), an automated mineralogy system, enables fast and quantitative mineral analyses of rocks, ores, concentrates, tailings, leach residues or smelter products. It combines BSE and EDX analysis for identification and measurement of mineral concentrations, particle size distribution, and liberation/locking parameters. In addition, it can provide bright particle searches for PGM, gold-silver ores, and/or REE. With the newly developed Automated Loading System (AutoLoader), the TIMA has become the world?s first automated mineral analyzer which permits robust, continuous and unattended sample loading. With the AutoLoader (robotics) system, the TIMA has emerged as a powerful plant support instrument. It increases the sample throughput, minimizes manual labor and enables 24/7 operations. As such, it can be used in daily, continuous mineralogy for mine geology/ore control, concentrators, leach operations, and smelter support. It will also increase the capabilities of technical service centers for mining companies, commercial laboratories, large drilling programs or pilot test campaigns. In combination with a highly automated sample preparation lab (sizing, potting and polishing), TIMA technology can establish high-throughput and fast-turnaround automated mineralogy lab modules for mine-site production support.

Feb 23, 2014

By Leon D. Keller

Hydraulic concentration of minerals has been practiced for a good many years. Until recently, however, the practice has been limited to a multiplicity of small pockets and relatively low tonnages and flows. The adaptation of the SiphonSizer to the concentration and classification of magnetite has changed this concept. Some fifty commercial units are currently in operation on magnetite, varying in size from 16 ft diameter circular unit to a 25 ft by 100 ft rectangular unit. Additional units up to 38 ft diameter are under construction. Depending upon the application in the flowsheet, upgrading-varies from 0.75% to 14% Fe in a single stage. To those not familiar with taconite processing, the importance of the struggle to economically remove as much silica as possible may not be fully appreciated. These figures pertaining only to transportation may be thought-provoking. If a 10,000,000 ton per year plant could reduce the silica content of their concentrate by 17, a savings in boat freight alone would amount to 100,000 tons at $2.00 per ton annually.

Jan 1, 1963

By B. J. Arnold

Utility coal specifications usually contain a requirement for a maximum moisture content in order to prevent coal handling problems and to minimize evaporative losses in the boiler. As most coal cleaning processes are water-based, dewatering and sometimes thermal drying steps are required to meet moisture specifications. Screens are often used for dewatering, with centrifuges and filters used to further reduce moisture in many cases. Algorithms to predict the performance of commercial dewatering devices were developed for the Coal Cleaning Simulator running under Aspen Plus? during a project sponsored by the U.S. Department of Energy and the Electric Power Research Institute. These algorithms include calculations for size degradation in the devices and fines loss to effluents, where appropriate, and a calculation for moisture content of the product based on particle size and specific gravity distribution. This paper discusses the algorithm for coarse and fine coal centrifuges and gives comparisons between predicted moisture and solids loss and published moisture and solids loss values for various particle size ranges.

Jan 1, 1996

By I. Sanchez

The development of the recent generation of large mining projects in South America has been challenging in many ways, but especially in the management of water in all its aspects. As a result, a number of projects have experienced difficulties and in some cases significant delays due to a lack of a clear and approved definition of the supply, use and discharge of water from mining and processing sites. The development of the recent generation of large mining projects in South America has been challenging in many ways, but especially in the management of water in all its aspects. As a result, a number of projects have experienced difficulties and in some cases significant delays due to a lack of a clear and approved definition of the supply, use and discharge of water from mining and processing sites.

Feb 23, 2014

By L. Bloom

In 1996, lack of confidence in assaying methods and sample handling affected companies as diverse as Bre-X and Timbuktu. Both share prices and the ability to raise financing are impacted when the quality of assay data is suspect. Overseas projects are subject to enhanced scrutiny when local facilities are used that are unfamiliar to brokers, financing agencies and banks. Quality control systems can be -implemented but there are associated costs. These costs should reflect the risk to the mining company, investors and financiers and the size of the proposed investment. In this regard, assay control call is considered a form of insurance to enhance the value of an exploration or mining project.

Jan 1, 1997

By Werner Burger

After its first introduction in 2013, Variable Density TBMs have increased their application significantly in mechanized closed mode tunneling. Throughout a variety of successfully completed and ongoing projects since then, Variable Density TBM technology has demonstrated its advantages in a wide range of applications. This paper will present the developments and lessons learned from these projects as well as the future potential of Variable Density TBMs.

Jun 13, 2021

By E. D. Attanasi, J. H. DeYoung

Several factors contributed to continued declines in mineral-exploration activity in the US in 1985. Low metal prices and, what appears to be worldwide chronic excess capacity in copper, molybdenum, lead, and uranium, have resulted in mineral-exploration expenditures remaining anemic. Economic recovery could result in a healthier mining industry and more cash flow to fund exploration. This is because general economic activity and US mining industry activity have historically been closely linked. However, as the worldwide economic recovery has expanded, the mining sector has continued its downward slide. New cuts in industry exploration budgets in 1985 shocked those who thought the exploration situation could not become worse. Some personnel and equipment had been redirected from base metals exploration to precious metals in the past few years. Last year, continued reductions in exploration sent many professionals out of the mining industry. Recent staff reductions or consolidations of operations were made by Noranda, Chevron, Molycorp, and other exploration companies. The latest data from the Society of Economic Geologists (SEG) summary of exploration statistics show that professional staff at year end in major US exploration companies (domestic and foreign operations) fell from 2355 in 1981 to 1868 in 1983 and 1277 in 1984. By the end of 1985, two economic trends were established that could improve the future profitability of mining and hence exploration. First, the price of crude oil began a decline. If sharply reduced energy prices increase worldwide economic expansion, the substantial excess capacity in some of the base metals industries could disappear, and prices could improve. Furthermore, if energy price declines reduce mining and processing costs significantly, metals may recapture some lost markets. The decline in oil revenues has already encouraged some oil-producing countries, such as Venezuela, to look toward development of mineral resources to earn foreign exchange for debt repayment. Second, the decline of the dollar by 21% during 1985 could also help US producers meet foreign competition. During 1985, industry restructuring continued as many oil companies sold off mining subsidiaries and minerals properties. Gold, silver in new discoveries Precious metals continued to dominate the announcement of new discoveries and exploration projects in 1985. A review of domestic exploration and development activities reported in several industry journals shows that 60% to 80% of these projects were directed primarily at precious metals, particularly gold. Base metals exploration activities frequently involved polymetallic deposits with gold or silver values. Because much of this exploration was done on identified targets (on-property exploration), the decrease in wildcat or grassroots (off-property) exploration may be more substantial than indicated by reductions in total exploration activity. Significant gold discoveries in 1985 included several in Nevada, among them the Genesis property of Newmont (near the Carlin mine), Goldfields' discovery of the Chimney deposit in Humboldt Co., and Freeport's discovery of two mineralized sites near Jerritt Canyon. Gold exploration continued to be focused in the western US and Alaska, but gold production starts at the Haile mine in South Carolina, and the Ropes mine in Michigan as well as Amselco's feasibility studies on deposits near Ridgeway, SC, are evidence that gold exploration is not limited to the West. The dominance of gold projects in exploration is not limited to the US, as demonstrated by gold dis¬coveries and exploration projects in Australia, Brazil, Canada, the Caribbean region, China, Guinea, Ivory Coast, South Africa, the South Pacific islands, and Thailand. From the standpoint of US metal miners, it is perplexing that worldwide exploration and development is also taking place in copper, zinc, tungsten, and other metals with depressed prices. During 1985, the US Geological Survey's efforts to map the sea floor of the Exclusive Economic Zone shifted from the Pacific Coast to the deep water areas of the Gulf of Mexico and to areas off the coast of Puerto Rico and the Virgin Islands. An atlas containing sea-floor maps of the west coast area was published as US Geological Survey Miscellaneous Investigations Series Map 1-1792. Results of the 1985 surveys are expected to be published by January 1987. Exploration trends - Statistical evidence Data from the SEG showed continued decline in the US mining industry's exploration expenditures through 1984. The share of US companies' domestic exploration expenditures directed toward base and precious metals has increased from 51% to 84% from 1980 to 1983 and to 86% in 1984. US mining companies spent about $0.67 of each exploration dollar in 1984 in the US. However, this represents an increase from earlier years. The 1983 data also show that firms spending more than $5 million on exploration accounted for 77% of exploration expenditures. Since 1981, the Bureau of Land Management (BLM) has been assembling data on claims and an-

Jan 5, 1986

By D. Zim

Mining activity in South America is a growing enterprise. One of difficulties found in many areas of the South American continent, especially in north Chile and south Peru, is the shortage of water supply. In order to overcome this difficulty some mining companies proposed to transport the water from Pacific Ocean up to the mountains. This can be accomplished by the use of stainless steel pipelines, but this is a cost prohibitive solution and is also subject to severe pitting corrosion in a saline environment. The use of mild steel may be a lower cost solution than stainless steel as the material of construction for pipelines but it is subject to corrosion anyway. The corrosion in this case can be internal or external corrosion although cathodic protection as well preventive maintenance usually is enough to mitigate external corrosion without the need to shut down the pipeline. The same is not true about the prevention of internal corrosion. It is not practical, sometimes not even possible, shutdown a pipeline to carry out an inspection and fix sections where potential failures are detected. It is possible avoid corrosion caused by sea water within the mild steel pipelines by applying a proper chemical program designed to virtually eliminate dissolved oxygen in the water commonly called deaeration.1 This type of treatment obviously involves additional capital investment since it requires the construction of one deaerator with the first pumping station and additional equipment at each point where the water can come into contact with oxygen. Deaerators will increase operational costs and subsequent injection of chemicals will be required in the case of multiple degasification facilities thus increasing the consumption of chemicals. grams based on oxygen scavengers, the objective of the present study is to develop a new water treatment capable of preventing mild steel corrosion in aerated sea water. The new treatment must be able to prevent both generalized and localized (pitting) corrosion and overcome the necessity to construct and operate deaerators.

Feb 23, 2014

By Wenming Wang, Edgar E. Vidal, Scott A. Shuey, Patrick R. Taylor, Judith C. Gomez

Introduction In modern society, vanadium is defined as a strategic metal. Some 90% of the global consumption is used as an alloying agent for carbon steels, tool steels, and high-strength low-alloy steels (particularly for pipelines). Advanced titanium-aluminum-vanadium alloys are seeing application in the aerospace industry. Small but ever growing amounts are finding application as catalysts or in electronics. New uses are continually being discovered for this metal. One example of a new application is the vanadium-redox battery for use in generation plants and back-up power sources. Vanadium is found in a large number of minerals, of which the most important are carnotite, roscoelite, vanadinite, mottramite, and patronite. Just over a third of the world's vanadium is produced as a primary product; the balance is a by-product of the iron and steel, oil refining, power generation and uranium enrichment industries. Vanadium can also be sourced by recycling spent catalysts from the petrochemical industry and ash produced by the combustion of oil emulsion in power stations. However, recycling activities are believed to account for only a small amount of total world supply. Vanadium is recovered from these ores largely as the pentoxide (V2O5) [1]. The major sources of vanadium-bearing magnetite ores are scattered throughout Australia, China, Russia, and South Africa. Current estimates of world’s Proven & Probable vanadium reserves are of the order of 41.3 million tones [2, 3]. Commercial vanadium-bearing titaniferous magnetite deposits can be found in Kachkanar, Russia; Pan Zhihua, China; Bushveld, South Africa; and Windimurra, Western Australia [4]. Other deposits have been found in New Zealand, Canada, and India, among other countries. Vanadium consumption in the steel sector has increased some 7% per ton of steel over the last 10 years as new alloying applications have been found to improve steel's strength-to-weight ratio. Future demand from the aerospace and nuclear industries for non-ferrous vanadium alloys such as titanium and super-alloys is also likely to grow. Vanadium is usually added in the form of ferrovanadium, a vanadium-iron alloy. Vanadium compounds, especially the pentoxide form, are used in the ceramics, glass, and dye industries, and are also important as catalysts in the chemical industry. While established approaches may be used at an industrial scale to treat vanadium-bearing titaniferous magnetite ores in several countries, new alternatives are being developed worldwide. This review will give short overview of the treatment of vanadium-bearing titaniferous magnetite ores, an overview of direct reduction and direct smelting processes and an approach to determine technical alternatives for the property.

Jan 1, 2005

By James F. Holzbach

Although Disputes Review Boards have been used for some time, they had not received wide publicity at the time Monroe County first used one. Public owners frequently resist adopting new contracting practices. This paper discusses an owner's experience with Dispute Review Boards, from learning about them to their use on two (2) projects. The experiences of potential and actual contractor claims are compared to a claim on an earlier contract and the ensuing litigation. Suggestions for possible use for Owner-Engineer disputes and recommendations for use are provided.

Jan 1, 1995

By P. D. Rao

Chemical and physical properties of typical low-rank coal (LRC) ash are significantly different than bituminous coal ash. With the exception of extraneous ash, which is incorporated during mining or is due to ash partings within or between coal seams, LRC ash consists primarily of inherent ash that is bonded into the coal's organic matrix or finely disseminated mineral matter. This paper reviews the nature of LRC ash, both inherent and extraneous, and how this impacts the prospects of washing and utilizing LRCs. A literature review, as well as washability data, proximate and ultimate analyses and ash analysis of 25 Alaskan LRC seams are used as a basis for this discussion. The authors' recent research into the nature and distribution of phosphorous in an Alaskan LRC is also discussed

Jan 1, 1997