Search Documents

By I. Shah, L. G. Austin

A method for quantitative investigation of the phenomena involved in fine grinding of materials that follows the changes in the breakage rates of fine particles has been presented. For relatively hard, brittle, non-coating material like quartz, the slowing down effect of breakage rates starts to be significant at relatively coarse sizes, which goes often undetected in closed circuit grinding systems, producing relatively coarse product, say P80=75µm However, for fine grinding systems, as the -10µm fractions begin to build-up, and classification becomes more difficult, the build-up of fine sizes causes a slowing down effect Compounding this problem is the difficulty of obtaining accurate cumulative weight size distributions in the fine size region.

Jan 1, 1983

By F. Varley

Researchers from the National Institute for Occupational Safety and Health (NIOSH), in cooperation with mine operators, conducted a study of heat stress exposures among mine rescue workers in underground mines. Mine rescue workers face extreme heat loads as they enter hot and poorly ventilated environments, particularly when they are wearing breathing apparatuses. The burden of wearing a closed-circuit breathing apparatus (CCBA), the inability to drink fluids for extended periods of time, and the potential for ventilation disruptions and fires combine to increase the risk of heat illness during a response to an emergency. In this research, ambient environmental conditions and heat strain indicators were measured using conventional ventilation monitoring tools during mine rescue training exercises. Heat strain was measured with an ingestible temperature-sensing pill that measured core temperature continuously. In addition, a heart-rate monitoring chest strap was used to indicate physical strain resulting from physical activity and heat. Both core temperature and heart rate data were trans-mitted to a remote recorder worn by a rescuer and time-stamped. Team activities were also observed to determine the contribution of work rate to a person’s total heat load. The effectiveness of several engineering controls, such as cooling the air inhaled by rescuers through an apparatus, wearing cooling vests, and supplying water through the CCBA masks, were investigated. Administrative controls, such as limiting the duration of exposure and controlling the work rate through forced-rest regimens, were also evaluated. Results to date are discussed, and tools for evaluating team condition and estimating the length of time it would be safe for rescuers to work are proposed.

Jan 1, 2004

By Levent Ozdemir, Bjorn Nilsen

For several recent TBM tunnel projects, unexpected ground conditions have been encountered, causing extra cost, considerable delay, and in some cases major claims. Undoubtedly, insufficient and/or irrelevant site investigation and testing are among the main causes of such incidents. The purpose of this paper is to review the main investigations and tests relevant for hard rock TBM projects, with particular emphasis on the considerable development that has taken place over the last few years. Also, guidelines for defining optimum scope and extent of site investigations and testing are discussed, as well as the importance of adjusting the investigations and tests according to complexity of the ground conditions and project type.

Jan 1, 1999

By Ch. Arvanitidis

This work concentrates on investigating the development of a geotechnical classification method for the Greek soils, which can readily provide a rough but usable estimate of the main strength parameters of the soil. It is expected that such a system will be useful to the structural engineer for either checking the laboratory results or for providing a direct estimate in cases where no tests have been conducted. The method provides strength parameter values by relating classification or physical parameters of various types of soils and/or in situ observations of geological and physiographical nature to the strength parameters, such as, cohesion, angle of internal friction, compressibility, modulus of elasticity, etc, by means of a statistical approach and the extraction of empirical formulae.

Jan 1, 2006

By Bezalel C. Haimson

Long before excavation begins, the in situ stresses in the horizon of planned underground chambers can be measured by employing the hydrofracturing technique in existing exploratory holes. Such measurements produce the stress magnitudes and directions required for the rational design of rock structures. Two recent case histories are cited in which preexcavation stress measurements for the design of underground powerhouses proved very beneficial in the orientation of the chambers and the estimation of the stability and required support. A third stress measurement case is related to the preexcavation design of tunnels that will house doughnut-shaped superconductive magnets for the storage of electric energy. In all cases, expensive later modifications were probably prevented by measuring stresses early in the design stage.

Jan 1, 1976

By Jan M. Mutmansky

While production scheduling for both surface and underground mining operations is similar in nature, a rather large array of techniques is applied in solving such planning problems. The techniques consist of both rigid operations research (OR) methods and practical procedures which are not mathematically based. In the following sections, a short summary of some of the techniques that are applicable to production scheduling problems in mineral operations is presented. The techniques discussed are: linear programming, integer programming, dynamic programming, graph and network theory, simulation, and heuristic methods. For an in-depth comprehension of these techniques, the reader is referred to any of the available textbooks on these subjects. One or more references will be listed for each topic to provide a starting point.

Jan 1, 1979

By K. T. Stafford, N. A. Iverson, V. T. McLemore

Southwestern New Mexico is part of a large belt of Late Cretaceous to Eocene copper porphyry deposits found in Arizona, New Mexico, and Mexico. These deposits are the result of arc magmatism that occurred during the Laramide orogeny. Recently, attention has been brought to other commodities that can be extracted as by- and co-products, many of which are critical minerals. A new compilation of the geochronology of these deposits shows two main pulses of magmatism that produced mineralized deposits and, along with new dates by the author, shines new light on the geologic history of these deposits and the role it plays in critical mineral abundance.

Feb 1, 2024

By F. B. Henderson

1.0 PROLOG Since the "end" of the Cold War, revolutionary new research and commercial remote sensing capabilities are being developed that will dramatically change the way we map the earth and address its environmental problems. The technology challenge is not the growth of new environmental remote sensing technologies themselves. It is, rather, how these new innovative observing systems can be accepted and used to the benefit of both the regulatory and the mining communities in the light of present concerns about unknown risks of discovery and liability. The basis for this paper is an unpublished technology primer prepared for the industry-government Workshop on Advanced Measurement and Site Characterization for Mining Impacts held at Colorado School of Mines, Golden, Colorado, July 14-17, 1997

Jan 1, 1999

In 1988, at the request of members of the Society for Mining, Metallurgy, and Exploration (SME) Inc., the president of SME formed Working Party No. 79, Ore Reserve Definition. Its mission was to develop guidelines for the public reporting of exploration information, resources and reserves. These guidelines were published in the April 1991 issue of Mining Engineering (pp. 379-384), and as a document entitled “A Guide for Reporting Exploration Information, Resources, and Reserves” in January 1992. Work continued on an ad-hoc basis until 1996. Working Party No. 79 was then renamed the SME Committee on Resources and Reserves and became a standing committee.

Jan 1, 1999

By Alice Blount, F. Patrick Carr

The quantitative evaluation,of quartz and other minerals in acid-insoluble residues from carbonate rocks and other industrial mineral products derived from sedimentary and low-grade metamorphic rocks is difficult. Commonly there are a dozen or more minerals present, and the suites vary from sample to sample. Because of these factors, either the absorption coefficient must be determined on a sample to sample basis or an internal standard must be used. Internal standards in general use are unsatisfactory. For example, [A1203] is often present in product samples because of ceramic grinding elements used in their production; CaF and LiF have peaks which overlap or nearly overlap mineral peaks in the samples. A careful evaluation has shown that magnesium aluminate (synthetic spinel) works particularly well as an internal standard for these types of samples. Not only does it have few, strong diffraction peaks which do not overlap, the peaks are in the same 28 region as the minerals, usually quartz and silicates, for which quantification is desired. Spinel also consists of equidimensional particles without prominent cleavages; this promotes a random orientation of the minerals in X-ray diffraction mounts. In addition, spinel can be used to correct for loss of diffracted-beam intensity due to thin sample preparations which are often unavoidable.

Jan 1, 1991

By Dale R. Ralston, Roy E. Williams, Gerry V. Winter, George L. Bloomsburg

INTRODUCTION The majority of ground water flow models have been developed for large computer systems. Most of these operate under a batch mode of operation, that is, the data are input with a deck of punched cards. The advent of micro- and minicomputers over the last few years opens the possibility of adapting many of these large flow programs to the smaller computers. In general, this adaptation will require more computer time to run the program, but in many cases if the small computer is in-house, the overall cost may be less than that required for a large computer. There are also a number of peripheral devices that can be used to make the data input much easier. As an example, the use of a digitizer with a finite element or finite difference mesh reduces the data input time considerably; the use of a graphics terminal for display of the mesh immediately after it is developed shows immediately whether there are errors in the location of node points. DEVELOPMENT OF AN INTERACTIVE SYSTEM The finite element program, UNSAT2, has been used over the past several years by the authors for several ground water flow problems (Bloomsburg, 1977; Bloomsburg and Wells, 1978; Zahl and Bloomsburg, 1980). In the past these programs have been run on an IBM 370/ 145 computer under the batch mode of operation. One difficulty that has been encountered has been in determining the length of time step that must be specified for operation of the program. The problem is that if the time steps are too large, the program becomes un- stable and operation ceases. If this happens in the middle of the problem, the only alternative is to reduce the length of time step and repeat the entire run. This problem has been alleviated in other pro- grams by using a subroutine that determines the time step automatically. If the solution becomes unstable, the time step is reduced automatically and that portion of the solution is repeated. With an interactive system this can be done by storing the output pressures and restarting the program with the new output pressures. Under the batch mode of operation, there is an option in UNSAT2 that allows restarting of the program from the last point of solution, but this must be specified when originally starting the program. The interactive computer system that we use currently consists of a PDP 1 1 /23 with hard disk drive, CRT terminal, plotter, graphics terminal, digitizer, and printer. The computer has 256 K bytes of core storage and the hard disk drive will accept a 5.2 M byte disk. To run a large program on a computer such as this, some overlaying must occur; that is, subroutines are stored on disk and put into core storage only when they are actually needed for running the program. UNSAT2 required very few changes to run on this computer but some changes were necessary to take advantage of the interactive capabilities of the system. One of these changes consists of the development of a program called DBUILD to build the data file for running the program. This program calls for each piece of data by prompt statement and gives instructions for using the digitizer. The data are then entered in completely unformated form. The node points must be entered in order and the coordinates are determined automatically by the digitizer. The pressure readings or initial conditions on each node point are entered through the terminal. All element information also is entered through the terminal. After DBUILD is run the mesh may be displayed immediately on the graphics scope whereupon any error in node point

Jan 1, 1986

By Rudolf E. Greuer

It is undisputed that an interaction between mine fires and mine ventilation systems exists. The ventilation carries the poisonous and sometimes explosive combustion products, which constitute the greatest danger of mine fires, through the mine and it provides the oxygen on which the intensity of the fire depends. The fire, on the other hand, can produce considerable ventilation disturbances which make it difficult to predict the path along which the combustion products travel. The opinions, how serious a threat such fire generated ventilation disturbances are, vary. Where shallow deposits are mined and brisk ventilation currents are used, it is frequently felt that these disturbances are of no serious concern. Where mine workings extend over larger elevation differences and where such disturbances have been encountered and been the cause of some larger disasters, their assessment is an integral part of all fire emergency plans. The author felt that the potential of digital computers for the design of ventilation emergency plans, contrary to their acceptance for conventional ventilation planning for more than two decades, is not yet fully utilized. He designed a program for the simulation of ventilation systems under emergency conditions in particular fires. This was part of work completed for a contract with the U.S. Bureau of Mines ( Open File Report OFR 115(1)-78)

Jan 1, 1980

By D. D. Banerjee, S. K. Kawatra, T. C. Eisele

A high calcium fluid-bed combustor ash has been shown to be an effective binder at dosages of 1 to 2% of the magnetite concentrate weight. Magnetite pellets 1.3 cm (1/2 inch) in diameter were produced with dry crushing strengths greater than 22.3 Newtons/pellet (5.0 pounds force/pellet), which is comparable to the results produced using conventional bentonite binder. The effectiveness of fly-ash-based binders was considerably improved when calcium chloride was added as an accelerator. Addition of calcium chloride at a rate of 0.1 to 0.2% of the total powder weight increased the strength of dried pellets by as much as 22% compared to the strength of pellets made using fly-ash without accelerators.

Feb 24, 1997

By Steve Kral

Competition in the gold mining industry throughout the world has become fierce in recent years. The challenge facing operations personnel is to produce more gold for less money. Likewise, the explorationist's charge is to find more gold in a more cost-efficient manner. That means using new technology to find new gold deposits and expand present ones. More accurate mapping instruments are available to geologists in the search for new deposits. Advanced geophysical and geochemical methods enable explo¬ration teams to review previously mined districts in their search for minable reserves. Four technical sessions on the geology, exploration, and development of gold deposits were part of the program at `world Gold '89,' a Gold Forum on Technology and Practices," held by SME and The Australasian Institute of Mining and Metallurgy in Reno, NV, Nov. 5-8, 1989.

Jan 1, 1990

By F. M. Doyle, Jun Li, Milton E. Wadsworth, E. Peters

The Raman spectroscopic technique was used to study electrochernically oxidized pyrite in-situ. It was found that Raman-active sulfur oxidation products could be detected after a proper potential was applied to the pyrite electrode for a threshold period of time. There existed a minimum potential below which sulfur could not be observed. However, when the applied potential exceeded a certain limit, the intensity of the sulfur spectra decreased. The minimum potential at which sulfur could be observed changed with solution pH. For both acid (pH 2.7) and weak alkaline (pH 9.2) solutions, the minimum potential was 0.8 V/SCE, whereas for neutral (pH 6.5) solutions the value was 0.4 V/SCE. In strong alkaline solutions (pH 12.5) surface sulfur oxidation products could not be detected at any potential.

Jan 1, 1993

By Felicia F. Peng

The naturally occurring aged manganese oxide coated on the granular media was found to have a catalytic effect on the removal of low concentration of Mn(II) (-1 ppm) from drinking water. Applying this principle, a manganese removal technique was developed for removal of higher concentration of Mn(II) (-100 ppm) from mine drainage by using various aged filter media and synthesized granular media with manganese oxide coatings. Laboratory-scale continuous granular media column experiments were conducted to assess the feasibility of manganese oxide-coated granular media for Mn(II) removal from synthesized mine drainage. The removals of Mn(II) were evaluated as a function of operation parameters including solution pH, manganese oxide concentration coated on the media, interstitial velocity, and oxidant concentration of influent. Higher solution pH and/or higher manganese oxide concentration promoted the removal of Mn(II) on the oxide-coated granular media under low interstitial velocity. Addition of sodium hypochlorite as an oxidant in the influent resulted in continuously regenerated oxidized surface to serve as the catalyst for Mn(II) oxidation reaction on the surface of oxide-coated media.

Jan 1, 1994

By R. Larry Davis

Over the past decade there has been a continual decrease in domestic oil reserves accompanied by a sharp increase in the demand for energy. Even with increased imports of foreign oil, the energy demand has not been met. This has forced many users to turn to substitute fuels. Of the many substitute fuels available most users are turning to and creating an increased demand for low sulfur coal. Because of the increased demand for low sulfur coal as well as the inherent problems in producing eastern coal, many producers have turned their attention to the large deposits of low sulfur coal in the western United States. Western coal mining is, however, not without its problems such as high moisture content, high ash content, highly variable sulfur content, multiple seams, and/or pitching seams. It is to aid in the solution of these problems that this chapter is directed.

Jan 1, 1979

By Gunter Swoboda, Harald Wagner

Until a few years ago tunnel construction was based exclusively on experience. In recent years, however, numerical models have increasingly become an integrated part of tunnel design [2]. These models permit good evaluation of the tunnel's support behavior even before it is designed. In particular, numerical methods are highly suited for the development of new construction methods. The prerequisite for this is the application of high-performance pre- and postprocessors, permitting the design engineer to come to a quick interpretation of the analysis results. In future, 3D analysis will take on increasing significance, for which reason this paper also deals with this type of models.

Jan 1, 1993

By A. K. Bakshi, Komar S. Kawatra

A plant trial of a new on-line pressure vessel rheometer for slurries, developed at Michigan Technological University, was carried out at a nearby copper concentrator. The rheometer measured the flow curves (shear stress vs. shear rate) of chalcocite slurries. Viscosity of non-Newtonian slurries changes with shear rate and so, for such slurries viscosity measurement at a single shear rate (often seen in the literature for grinding and classification studies) cannot be correlated to process performance. For these slurries, viscosity at various shear rates can be measured from flow curves generated by the pressure vessel rheometer. Other rheological properties, such as flow type and yield stress can be determined by this rheometer to better characterize the slurries. The slurry at the copper concentrator consisted of ground chalcocite ore. The solids content in the slurry varied between 30-60 % by weight. Top size of the particles was 125 micron, and 80% passing size was 34 micron. Measurements by the pressure vessel rheometer showed that most of the slurries had pseudoplastic flow at shear rates below -3000 sec-l, where the viscosity of the slurry decreased with increase in shear rate. Above -3000 sec-l, like a Newtonian fluid, the viscosity of the slurry remained steady. Flow curves and viscosity from the pressure vessel rheometer were verified with a Brookfield viscometer and a vibrating sphere viscometer, and the results were found to be accurate.

Jan 1, 1997

By D. M. Galbraith

British Columbia's physiography - the mountains, valleys and watercourses - provides the basis for rich and varied plant and animal resources and for complex land uses. Mining alters the physical environment in a manner that may create a disproportionate impact on biological resources and land use systems. The object of environmental legislation is therefore largely the protection of the basic physical environment: land surface, water, and air. The pace of mineral exploration, placer mining, and underground and surface gold mining has recently quickened in British Columbia, testing the ability of both industry and regulatory agencies to respond to legislative requirements. Some parameters of mining activity have critical significance for environmental protection, for example: the area disturbed; the physical and chemical qualities of ore, waste and overburden; and the nature of materials handling. Acid mine drainage is a particular hazard. Provincial legislation that applies to mining includes the Mines Act, the Environment Management Act, the Waste Management Act, and the Water Act. Government of Canada legislation includes the Fisheries Act and the Metal Mining Liquid Effluent Regulations. Every new mine proposal in British Columbia is reviewed in the Mine Development Review Process, which receives its mandate from the Provincial Environment and Land Use Cabinet Committee. The proponent submits reports to the Mine Development Steering Committee in succeeding stages: Prospectus, Stage I (after which approval-in-principle may be granted by ELUC); and if necessary Stage 11. Stage 111 is the

Jan 1, 1987