Search Documents

By Z. Zhongwei

The leaching kinetic of mechanically activated sphalerite with acid FeCl3 solution was investigated. The result has shown that mechanical pre-treatment has greatly enhanced the leaching process. Comparing with the original concentrate, the activated one can be leached more completely at relatively lower temperature with diluter FeCl3 concentration within a shorter leaching time. The activation energy for the activated concentrate is 27 KJ/mol, while for the original one is 52 KJ/mol.

Jan 1, 1995

By A. M. Raichur

Flocculation of fine coal is usually accomplished with the addition of commercially available organic flocculants. Recently it has been shown that biopolymers derived from microorganisms can be used to flocculate coal. The biopolymers flocculate coal efficiently and render the coal surface hydrophobic. The increase in hydrophobicity can be utilized either to separate the coal flocs from mineral matter. It can also be used for reducing the moisture content of fine coal. In this regard, flocculation and settling tests of fine coal with biopolymers and synthetic flocculants was undertaken and the results are discussed here. Also, a transport model was developed for the time-dependent settling tests for fine coal.

Jan 1, 1996

By Thomas A. Mekelburg

Due to a tight ash constraint on the clean coal product and difficult middlings washability characteristics, a considerable amount of coal was being lost in the jig middlings at the Monterey No. 2 Mine. An investigation was conducted into circuitry to recover this lost coal with minimal effect on the total clean coal ash. A reverse two-stage hydrocyclone system cleaning at low specific gravities was selected. This system is currently recovering approximately 5.8 kg/s (23 tph) of 11.5% to 12.5% ash coal. The specific gravity of separation for the system is about 1.5 and the probable error is 0.13.

Jan 1, 1984

By Ralph S. Mattson, Frederick T. Hancock

GENERAL DESCRIPTION The Granduc mine is situated on the west side of Granduc Mountain in the Leduc River area of north¬west British Columbia about 51 km (32 miles) north¬east of the town of Stewart. Entry is by means of a 16.6-km (10.3-mile) long haulage adit from the concentrator site at Tide Lake. The principal ore mineral is chalcopyrite. Ore mineralization varies from dis¬seminated to irregular semimassive stringers generally associated with highly folded and sheared biotite-rich sections of metasediments. The ore bodies vary in width from 3.6 m (12 ft) to over 18 m (60 ft) in a zone some 800 m (2600 ft) in length dipping at an average of 75° to the west and plunging steeply to the south. Capping varies in thickness from 0 to over 300 m (1000 ft). SELECTION OF MINING METHOD In the early stages of planning the primary require¬ments to be met by the mining method were: (1) suit¬ability to high output and productivity, (2) adaptability to mechanization in order to minimize operating costs, and (3) minimization of the costs and the development period for preproduction. Considering these, the selection of a mining method was narrowed to a choice be¬tween sublevel long-hole stoping or sublevel caving. A method utilizing backfill was ruled out as uneconomical, especially since mill tailings would not be readily available. At the time, the following facts about the ore body were recognized: (1) the average width of the ore body was 12 m (40 ft), (2) 30% of the stoping blocks were in areas of 6 m (20 ft) or less in width; (3) in many cases, ore zones were located in parallel lenses or were irregular in shape; (4) major faults were present in the hanging wall close to the ore, with minor faults within the different ore zones; and (5) the ore itself was lami¬nated with fractures and jointing crossing such bedding planes. Considering these factors, the two stoping meth¬ods were compared. Sublevel Open Stoping The characteristics of sublevel open stoping are: 1) It is generally not used for widths below 6 m (20 ft) since the ratio of waste development increases as level intervals are reduced to insure good control of long-hole drilling. 2) This method is used where ground is relatively competent. Otherwise more pillar support is required, increasing ore losses or mining costs with pillar recovery. 3) The method is not easily adaptable to parallel ore zones separated by relatively narrow waste bands. 4) Close control of pillar and stope design will per¬mit some degree of dilution control. Sublevel Caving Sublevel caving is characterized by the following: 1) The method can be used for a variety of ore widths, recognizing that 3 m (10 ft) in width may be an economical minimum. 2) It is particularly favorable where wall rock is weak. 3) The method has flexibility so that irregular ore bodies or parallel lenses can be mined. 4) The need to leave pillars for support is eliminated 5) Dilution and tonnage recovery are interrelated. With concern about the stability of the hanging wall and the geometry of the ore bodies, there was a growing favor to choose the sublevel caving method. However, this method was relatively new to Canadian mining practice. Teams were sent to Sweden to tour mines using sublevel caving and to study their methods and any extraction and dilution problems. The objective was to develop cost and performance data and ore recovery grades and tonnages for feasibility comparisons. Next, detailed mine plans were developed covering a three-year period using sublevel caving and sublevel open stoping. Extensive analyses of the development and production costs for each method were made. With sublevel caving, ore losses of 10% with a 20% dilution rate were used. The same ore loss was estimated for sublevel open stoping with dilution varying from 11 to 15%. As a result of these studies, the decision was made to use sublevel caving partly because slightly lower op¬erating costs, together with higher productivity, offset the adverse effects of higher dilution; and partly be¬cause, at the start, there would be less risk in being able to handle the ground, and the method offered more flexi¬bility. Open stoping was not ruled out for testing at a later date. It was recognized that some other method of mining would be required for mining the ore extensions below the glacier, where surface subsidence must be avoided. During the operating life of the mine, open stoping was tested in narrow width ore zones and found un¬satisfactory due to wall failure. A cut-and-fill stope, utilizing run-of-mine waste from development, was also operated on a trial basis. A sequence was finally estab¬lished that permitted ground control; however, produc¬tivity needed considerable improvement in order for open stoping to be considered as a sole alternative for mining below the main haulage level. At the termination of operations in June 1978 over 13 000 000 t (14,500,000 st) had been extracted from above the main haulage level at production rates varying from 3270 to 7250 t/d (4000 to 8000 stpd). Sublevel Caving Methods Two basic methods were used, transverse and longi¬tudinal. The transverse method was used mainly in the upper C ore body in widths greater than 18 m (60 ft), and occasionally as an alternative to the longitudinal method in localized areas where strike faulting inter¬fered with normal development. The longitudinal method was used in ore bodies varying in width from 3.6 to 18 m (12 to 60 ft), with a multilongitudinal varia

Jan 1, 1982

By Panshi Xie, Yingyi Zhang, JIANJIE DUAN, Shenghu Luo

A multi-layer gangue roof of a steeply dipping coal seam with a large mining height face area was analyzed using physical simulation, numerical simulation, theoretical analysis, and field measurement methods to evaluate the roof deformation and the mechanisms associated with the instability of the hard gangue and soft coal interlayer. The results indicated that the first weighting step of the multi-gangue roof was larger than that of a non-gangue roof, but periodic weighting steps were similar. The overburden collapse height was lower in the multi-gangue roof than in the non-gangue roof due to the buffering and supporting function of the collapsed gangue. Moreover, the failure of the coal interlayer was the key factor in the collapse of the multi-layer gangue. A mechanical model was established for the hard gangue and soft coal interlayer based on a revised Prandtl squeezing theory. The limited load of the interlayer and maximum resistance of the shield support was thusmodeled. The maximum resistance of the support increased with the dip angle of the seam and burial depth. It also increased with the interlayer thickness at thicknesses below 2.75 m. It reached a peak when the interlayer thickness was between 2.75 and 3 m and exhibited a decreasing trend when the thickness was greater than 3 m. The results were confirmed using physical simulation and a field test. Certain measures were proposed to control the stability of the gangue roof, including zoning control of the mining height and resistance and advancing the support while maintaining roof contact, thus ensuring the integrity of the support and surrounding rock system.

Jun 30, 2020

By Richard C. Corson

The objective of blending materials in a bedding pile is to reduce the variation in successive samples taken from the materials to be blended. In designing a bedding and reclaiming operation, several mechanisms are available to effect the reduction of variability, or increase in homogeneity, of the materials. These mechanisms can act before stacking, in the stacking process, in reclaiming and after reclaiming. In evaluating alternative methods of stacking and reclaiming, the potential user must judge each method on the basis of certain criteria; the capital cost of the equipment, the allowable absolute variability of the reclaimed product and the effectiveness of blending. Several stacking and reclaiming methods have been tested using a computer simulation. Based on the results of this program, factors were developed to describe the effectiveness of blending for chevron stacking of discrete materials and preblended materials, bucket wheel reclaiming and drum reclaiming. From these factors, the total effectiveness of a combined stacking and reclaiming system can be determined.

Jan 1, 1985

By M. McPherson, G. Danko

Methods of measuring in situ rock thermo-physical properties are rapidly evolving. Among those existing in the literature, a particular measurement procedure was selected for further development. The measurement is based on creating a spherical temperature field in a drill hole using a point source heater of constant heat flux. The bivariate temperature distribution 0 (r, t) is measured at several points along the length of the drillhole, radius r from the heater and at particular time intervals (t). A number of different evaluation methods were tested for calculating the unknown thermal conductivity (k) and diffusivity [] from the measured temperature and the known heat flux. The results showed that evaluation using the finite difference scheme and small temperature differences measured at points close together, cannot give a reasonable result. In order to solve the problem a new general analytical evaluation method is developed. Using an appropriate technique, it is possible to simultaneously obtain values for k and [], incorporating a semi least square technique to reduce the uncertainty in the evaluation. The new device and evaluation method makes it possible to obtain from a single drill hole highly precise k and [] values within an 8 hour period. The method has been used in several underground mines in the U.S. with good results.

Jan 1, 1987

By Pratt Rogers, Aaron Young

This paper considers the mining industry’s need for digital transformation (DT) and presents a three-part review of the foundational components of the DT process: ubiquitous data, connectivity and decision-making. It also provides a discussion on the future of DT in mining as well as a research direction, which identifies the need of academia to provide support for mining companies in the form of both research and the education of digitally literate, dynamically capable mining engineers into the coming decades.

By Kenneth J. Miller

A novel two-stage froth flotation process to remove pyritic sulfur from fine- size coal is described. The process consists of a first-stage, standard coal flotation step in which high-ash refuse and some of the pyrite are removed as tailings. The first-stage clean coal froth concentrate is then repulped in fresh water, and a coal depressant, a pyrite collector, and a frother are added to float the remaining pyritic material. Laboratory and pilot plant flotation results with coals from the Lower Freeport and Pittsburgh beds are given. The pilot plant test results show that up to 80 percent pyritic sulfur reduction was achieved with the Lower Freeport bed coal and up to 50 percent with the Pittsburgh bed coal. Laboratory and pilot plant results were in excellent agreement, indicating that the process is a viable means of removing much of the sulfur from some coals.

Jan 1, 1974

By E. Taskin

Diasporic bauxite from the Mugla-Milas region was mechanically activated in a planetary mill for different activation times and the structural changes were examined by X-ray diffraction analysis (XRD), scanning electron microscopy (SEM) and specific surface area analysis (BET ? Burnauer, Emmett and Teller). Non-activated and activated bauxite samples were leached directly in alkaline (Na2O) solution at atmospheric conditions and the activation procedure led to the amorphization and structural disordering of the diasporic bauxite structure, which increased the dissolution efficiency. Effects of milling speed, liquid/bauxite ratio and leaching time on alumina extraction in direct alkaline leaching of diasporic bauxite were also studied. The alumina extraction was ~7% for non-activated bauxite and ~70% for activated (75 minute) bauxite. Key words: Diasporic bauxite, Mechanical activation, Alkaline leaching, Alumina extraction

Jan 1, 2009

By V. B. Menon, L. D. Michaels, M. E. Mullins

Introduction The cleaning of coal to remove sulfur and inorganic impurities has, in recent years, become an essential operation in any coal utilization process. US coals, on average, contain about 3% total sulfur, of which more than 60% is generally inorganic or pyritic sulfur. Existing technologies such as heavy media cycloning, selective agglomeration, and electrostatic separation have the potential for removing about 80% of the pyrite from coal (Khoury, 1981). In view of the large volumes of coal being used today, there exists a need for the development of new processes to further improve the separation of pyrite from coal. Colloidal particles in suspension possess surface charges that are related to the chemical composition of the particles. In aqueous suspensions, the surface charge is a function of pH. For coal-pyrite mixtures, it is possible, by an adjustment of the pH (also a function of polar molecules), to reach a state where the charge on coal is very close to zero, but the charge on pyrite is still substantial. The introduction of collector particles with a charge opposite that of the pyrite should then result in the selective flocculation of pyrite and collec¬tor. These flocculates should settle out much faster than coal and could be removed from the bottom of the settling column. This note discusses our preliminary observations of the effect of clay-based collector particles, especially bentonite, on the settling behavior of coal and pyrite. These experiments were conducted with a view to developing a new electrokinetic flocculation process for separation of coal-pyrite mixtures. Experimental The objective of the experiments was to determine the effects of clay-based additives on the settling rates of clean coal, pyrite, and coal-pyrite mixtures. Illinois Colchester (No. 2) coal was obtained after processing in an existing coal cleaning facility. This coal was reported to contain less than 0.3% pyritic sulfur, which was in the form of a fine powder with an average particle size of 5µm. Pyrite (of average particle size 5 µm) was also obtained from the same facility and reportedly contained less than 0.1% coal. The zeta potentials of coal and pyrite in water were measured as a function of pH using a zetameter. The pH was adjusted by adding sodium hydroxide or hydrochloric acid to the suspensions. Sedimentation experiments were conducted in 50-mL glass cylinders, and settling rates were measured by noting the height of clear liquid above the settling front as a function of time. Settling behavior was also charted by periodically taking photographs of the system. The following systems were investigated: •a slurry consisting of 2.5 g of clean Illinois Colchester coal in 50 mL of water of pH 6.0, with and without the addition of 0.5 g of bentonite (Fisher, purified grade) ; • a slurry consisting of 2.5 g of pyrite in 50 mL water of pH 6.0, with and without the addition of 0.5 g of bentonite ; and • a slurry consisting of a mixture of 1.25 g clean coal and 1.25 g pyrite in 50 mL water of pH 6.0, with and without the addition of 0.5 g of bentonite. In addition, experiments were conducted with kaolinite (Bath, South Carolina) and alumina (Fisher, purified grade) as collector materials to verify the observed effects. Results and discussion Figure 1 shows the zeta potential values for the Illinois coal and pyrite as a function of pH. The zeta potentials of coal and pyrite decrease with increasing pH, changing from an initially positive value at low pH to a negative value at high pH. The point of zero charge (PZC) for the coal is at a pH of 6.2, while the PZC for pyrite occurs at a pH of 10.3.

Jan 1, 1988

By W. D. Elston, A. E. McLaughlin, G. B. Hampton, W. L. Barham, J. F. Murphy, W. H. Cundiff, J. W. Mulloy, R. G. Breuer, J. W. Shaffer

Introduction Alumina (aluminum oxide) is the material from which all the world's aluminum is produced. In the Western World, all the alumina is made from bauxite by the Bayer process. In the nearly 150 years since aluminum was first isolated by Oersted, the metal has grown from a laboratory curiosity to a position of major importance in the world's commerce. In terms of annual production rates aluminum is first among nonferrous metals. Oersted's discovery-reduction of aluminum chloride with potas¬sium amalgam-was improved on by Ste. Claire Deville, whose so¬dium amalgam reduction of aluminum chloride led to the commercial production of aluminum in France in 1855. Ste. Claire Deville's method prevailed until 1886 when Charles Martin Hall and Paul T. Heroult each invented a process for the production of aluminum by the electrolysis of alumina dissolved in molten cryolite. The inven¬tion by Karl Josef Bayer in 1888 of an economical process for making very pure aluminum oxide (alumina) from bauxite established the necessary link between known ores and the Hall-Heroult reduction process. Bayer's work completed the scientific base-the ore bauxite refined to alumina by the Bayer process (U.S. Patent No. 515,895), the alumina reduced to aluminum in the Hall-Heroult cell (U.S. Patent No. 400,766--upon which today's aluminum industry is founded. Small-scale production of aluminum in the U.S. began in 1888 utilizing the Hall cell. By 1903, bauxite properties and a Bayer process refining step had been incorporated into the production activities. On this base the aluminum industry in the U.S. has grown at an annual compounded rate of 15%. Since 1946 the annual growth rate has been 10%.1 The rapid growth of the industry is the result of many factors among which are the existence of widespread bauxite ore deposits; a sound and economic production technology; and the properties of the metal-lightness, strength, ductility, good electrical and heat con¬ductivity, and pleasing appearance, which lead to ever greater de¬mands for aluminum in an industrializing society. At the inception of the industry, the only market that could be found for aluminum was in the production of cooking utensils. How¬ ever, the rapidly accelerating industrial and technological development of the Western World soon created new needs for aluminum, and today aluminum is marketed in a broad range of industrial, commer¬cial, and consumer applications. The principal uses for aluminum are:' building and construction, 22%; transportation, 18%; electrical, 13%; packaging, 11%; consumer durables, 10%; machinery and equipment, 7%; other, 19%. The 1974 production of primary alumi¬num in the world was 14.5 million short tons, which at an approximate ingot price of 40¢ per lb puts a value of $11.6 billion on the industry product prior to fabrication. While aluminum is widely distributed in the earth's crust and is a major constituent of many rocks and soils, to date no method of extraction of aluminum from such nonbauxite material has been brought to commercial practice in the Western World. In the USSR alumina is produced by the complex processing of nepheline syenite, but elsewhere all commercial production of alumina is from bauxite. A brief discussion of recent developments and other processes for alumina is included in the subsection "Other Processes for Alumina," page 19-15. In early 1973, a major U.S. aluminum producer announced the successful development of processes for the production of aluminum from aluminum chloride. This achievement promises to exert a major influence on the future of the aluminum industry. In the initial com¬mercial application of this new technology, Bayer alumina will be chlorinated, and the aluminum chloride then reduced by electrolysis. Important claims for the new processes are lower energy requirements (one-third less than obtainable in Hall cells) and reduced labor costs. Capital costs are said to be no greater than for conventional plants. While the announced intention is to produce the aluminum chlo¬ride from Bayer process alumina, the new chloride reduction process will eliminate the other raw materials, carbon and fluorides, required by the conventional Hall cells. The electrodes in the chloride cell will not be consumed on the reduction process and the electrolyte will have, as the name indicates, a chloride rather than a fluoride base. 2. Bauxite Definition and Origin. Bauxite is a naturally occurring raw material composed principally of a mixture of one or more of the hy¬drated aluminum oxide minerals gibbsite (Al2O2 3H2O), boehmite (Al2O3 H2O), and diaspore (Al2O, - H2O), and impurities of silica, iron oxide, titania, and other various elements in trace amounts. It is an end or near-end product of chemical weathering. Depending on the amount of iron impurities, the color of bauxite varies from dark red and brown to pink to white. Some bauxite is finely divided, free digging earthy material, while other forms are dense and rocky, requiring explosives in mining. Many gradational forms exist. It is one of the most variable of mineral raw materials in chemical composition and physical appearance. It is generally believed that bauxite deposits resulted from intense chemical weathering of aluminum-bearing rocks or formations under tropical or subtropical conditions with alternating wet and dry sea¬sons. Topographic conditions were favorable for drainage and the in-situ accumulation of aluminum, iron, and titanium oxides. There was low to moderate topographic relief with a minimum of erosion during long quiet periods in earth history.2 The occurrence of bauxite is widespread and it has been found on all continents except Antarctica. Production was reported from 27 countries in 1974, at which time total world production was over 79 million metric tons. Of this production 76% was from seven coun¬tries-Australia, Jamaica, Surinam, Guinea, USSR, Guyana, and Greece-which ranked in that order of production. In Table 1 are shown typical compositions of bauxite from some

Jan 1, 1985

By Charles W. Daugherty, Eugene B. Waggoner

In the construction of recent subsurface projects, particularly mined openings and transit systems, it has been apparent that final costs were often greater than first expected. Because many overruns result from alleged differing site conditions, there was reason to suspect that pre-bid geotechnical investigations were inadequate for predicting subsurface geology. In 1982, nine federal agencies involved in constructing underground facilities funded the National Academy of Sciences' U.S. National Committee on Tunneling Technology (USNC/TT) in an effort to evaluate and clarify the relationship between geological knowledge and construction costs. That committee formed the special Subcommittee on Geological Site Investigations, which spent more than two years studying underground projects by examining contract documents and geologic reports, making site visits, and interviewing owners, designers and contractors. The study ultimately encompassed 84 mined tunnels and chambers and three deep shafts in the United States and eastern Canada. Data collected on geologic exploration, design and construction were analyzed and conclusions reached concerning whether and how site investigations need to be improved. The results of the study are published in two volumes by the National Academy of Sciences. Due to the recent completion date of the main report, it was not possible to prepare a summary for inclusion in the RETC Proceedings. However, the complete two-volume report, "Geotechnical Site Investigations for Underground Projects," can be obtained by writing or calling: U.S. National Committee on Tunneling Technology National Academy of Sciences 2101 Constitution Avenue, N.W. Washington, D.C. 20418 (202) 334-3136

Jan 1, 1985

By Y. Luo

Surface subsidence process due to underground coal mining often has the potential to cause problems to buried pipelines. In this paper, a technique for assessing the stress level on a subsidence-affected pipeline is introduced. The main contributors for the stresses on the pipelines are identified. Mitigation techniques for reducing the stress on the pipeline have been proposed and successfully tested.

Jan 1, 1997

By Leonard B. Rothfeld

For many years, pulverized coal (PC) boilers in utility power plants have been the dominant market for domestic coal. Today, two new coal utilization technologies challenge the PC boiler's dominance. Atmospheric fluidized bed combustion (AFBC) and "coal gasification/combined cycle" (GCC) stand on the verge of commercial demonstration in the utility environment at a scale of 100 MW. Developed over the past decade, these technologies respond to the demands for cleaner ways to burn coal and for more flexibility in fuel supply. In the near term, these are the "clean coal" technologies most likely to have a significant impact, because they are ready for commercial application. As for environmental acceptability, consider that just a few years ago one of the environmental slogans was "no coal in California." Indeed, the only large quantities of coal above ground in California at that time were in transit on the way to Asia. Today, thanks to new technology, we can point to two operational coal-burning plants in California and one in the works: * Cool Water GCC demonstration plant (100 MW) * California Portland Cement AFBC commercial cogeneration, near Riverside (190 000 lb/hr steam) * Energy Factors AFBC commercial cogeneration at Stockton, to be operational 1988 (44 MW)

Jan 1, 1987

By D. Wallace Fields

Increasing public pressure and demands from various tiers of government have generated a legislative maze of statutory and administrative requirements facing industries involved in mineral extraction and processing. Each tier, of government has asserted concurrent jurisdiction and threats of harsh measures if industry does not satisfy all requirements. In the field of water pollution control, federal requirements have increased, carrying with them increasing techniques of enforcement - ranging from injunctions through criminal penalties. Federal laws have required that states formulate water quality standards as an adjunct to federal regulation. Florida has reacted with the Water Pollution Control Act of 1967. This act incorporates state water quality standards and permit requirements for any installation constituting a potential source of pollution, and provides for civil sanctions as well as injunctive relief. The federal government has utilized an 1899 law to require a permit for discharges into navigable waterbodies - a term which has been judicially defined to include any watercourse capable, after reasonable improvement, for use in the transportation of waterborne traffic. Failure to secure these permits can result in the issuance of an injunction or civil or criminal penalties. The Corps of Engineers will not issue these permits without the approval of the discharge by state, local and other federal agencies. Air pollution similarly is regulated by a multi-tiered network of laws and administrative standards. Federal regulation has increased from early research support in the 1950's through the development of Air Quality Standards and their enforcement by large fines, injunctions, administrative conferences and public hearings. Florida regulation, under the Florida Air Pollution Control Act of 1967, parallels federal law but grants concurrent regulations, requirements and enforcement tools to local and state agencies. Although previous state regulation was minimal, consisting only of three acts passed in 189 1, 1899, and 1911, in the future the mining industry will have to contend with this increasing network of ecological requirements. It is recommended that the industry take the initiative by involving Florida in the Interstate Mining Compact, as well as seeking the passage of a state reclamation law funded by a severance tax.

Jan 1, 1972

By M. Ge

An in-seam seismic (ISS) - based void detection technique was developed and tested for three general mine conditions: anthracite, bituminous and trona. The detection range tested varied from 80 to 100 m for trona mines and from 33 to 66 m for bituminous mines. High quality and broad band signals were obtained from these tests and were used to delineate the voids. The paper provides a brief discussion on the technical features of this void detection technique, the testing conditions and results, and a general assessment of the technique.

Jan 1, 2010

By L. P. Meade

The particular impact of imported industrial minerals varies within the Industry and is dependent upon many diverse factors. In a similar way, the impact on individuals has been varied and the degree of impact will depend partially on the individual's ability to handle change. Just as many corporations are adjusting their marketing strategy and production methods to compensate for imported mineral products; individual managers, mining engineers and geologists are making adjustments to their own personal job marketing techniques and on-the-job operating procedures. Modifying the degree of impact for both industry and individuals depends upon the ability to adapt.

Jan 1, 1988

By C. P. Siess, S. L. Paul, E. H. Gaylord

Several types of tunnel supports are being investigated experimentally and analytically at the University of Illinois at Urbana-Champaign under the sponsorship of the Federal Railroad Administration, Department of Transportation. The results of work on two types will be discussed here. These are steel sets and continuous, monolithic steel-fiber-reinforced concrete liners. The latter is a model of a short length of liner that might result from a continuous slip-forming operation in a tunnel excavated with a boring machine. Tests have been performed on both types of support and analyses are being developed which will greatly broaden the scope of the test program. The objective of these studies is to improve the understanding of basic behavior of these supports, and to develop techniques for their analysis. The analyses will then be used to perform parameter studies that will lead to more rational procedures for structural design. The tests provide a check on the accuracy of the analysis and demonstrate the overall behavior and modes of failure. Another part of the project is concerned with the interaction of support and medium, and thus prediction of loads for the supports. These studies are presented in greater detail in a recent report (1). A brief outline of results obtained to date are presented in this paper. STUDIES OF STEEL SETS Description of Set Tests The sets tested were of the horseshoe type with a 5-ft radius arch section and 7-ft straight legs. They had bolted joints at the crown

Jan 1, 1974

By Jesse L. . Jr. You

Tunnels in the granitic Climax stock at the Nevada Test Site were inspected for keyblock occurrence. Thirteen relatively large pyramidal keyblocks were located in about 230 m (750 it) of tunnel. Orientations, dimensions, joint roughness coefficients, and joint compressive strengths were measured for the faces of nine keyblocks. The measurements were used to back-analyze keyblock stability to check the validity of a numerical model for keyblock behavior. A newly developed three-dimensional numerical model correctly predicted whether or not each keyblock failed in six of eight cases. The two exceptions involved stress conditions and keyblock locations that clearly violated the assumptions that underlie the stability model. The observations also allowed the effect of tunnel orientation on keyblock occurrence to be evaluated. Of the thirteen observed keyblocks, nine large blocks were found in less than 30 m (100 ft) of the Piledriver drift (which runs N56E) while only four blocks of comparable size were observed in 200 m (656 ft) of the Spent Fuel Test--Climax drifts (N61W). The orientations of the keyblock faces were checked against known discontinuity set orientations; some of the faces correlated well with mean set orientations, whi.le other faces were fringe members of sets. Stereographic techniques were used to examine the frequency of keyblock occurrence and to determine the maximum keyblock size that could be encountered with a given combination of discontinuities. Keyblock occurrence was found to be affected by tunnel orientation in a predictable way; this can be used to guide or improve tunnel design practices.

Jan 1, 1986