Search Documents

By D. B. Stephens

Assessing the occurrence of natural ground-water recharge at mine and mill waste disposal sites may be crucial to addressing regulatory agency concerns regarding the potential impact of waste seepage on ground-water resources. Recharge has been shown to occur even in semi-arid areas where annual lake evaporation exceeds precipitation. Permanent storage of waste seepage in the unsaturated zone is not to be expected if recharge occurs under natural conditions. Establishing the direction and rate of fluid movement in the vadose zone by field measurements is an important element that should be included in the site selection process.

Jan 1, 1987

By L. Reyes-Bozo, R. Ginocchio, A. Godoy-Faúndez, C. Sáez

Relationships among mining industry, society and environment have been historically complex due to its environmental impacts. In the Chilean mining industry, repetitive and small spills of fuel during maintenance of machinery have been adsorbed by desert soils and sawdust to control environmental pollution. The froth flotation is the main technology to recover specific mineralogical species from sulphide ores. Flotation reagents are expensive and representing an environmental risks due to its physics properties. Our objective was to investigate the feasibility of applying bioremediation as a cost-effective alternative technology to physical-chemical treatments and to evaluate the efficacy of biosolids as foaming agents. Our results show that the bioremediation is feasible by use of the autochthonous microbial communities and biosolids could be used as new environmental-friendly organic reagents. This research discloses a sustainable bioremediation process and industrial ecology model based on these two successful cases.

Jan 1, 2011

By Charles H. Jacoby

In 1960 the management of International Salt Company made the decision that all waste material from the Watkins Glen plant would be stored in underground salt cavities. The cavities which they contemplated using had been depleted of salt to a point where continued operation would have impaired their structural stability. Originally, the waste to be disposed of included vacuum pan bleeds, cinders, contaminated salt and sewage. It was proposed that this material, in a slurry form, was to be injected into the salt cavity through one of the abandoned wells. Brine, displaced from the cavity, was to be recovered from an adjacent well and subsequently injected into the Cherry Valley limestone, This Cherry Valley limestone which underlies a large portion of north central New York contains a connate water with high concentrations of ammonia, hydrogen sulphide and the chlorides of calcium, magnesium and sodium. A number of questions were immediately raised on various aspects of the technical feasibility of the project. Of major concern was the buildup of insolubles adjacent to the bore of the injection well. Another pertinent question was the carryover in the displaced liquor of finely-divided, mechanically-suspended particles. Criticism was leveled at the inclusion of sewage. Engineering studies were started by the company's Mineral & Mines Development Department and on April 3, 1961 a preliminary feasibility report was issued.

Jan 1, 1973

By T. Lupek, S. Plaum

"The execution of classical building services in underground mining operations is more truth than myth. From small concrete foundations for conveyor belts to the construction of huge workshops for large machinery maintenance, nearly every operation requires building services. By creating such fixed facilities, these services ensure the efficiency of the production. A distinction must be made between fixed facilities which directly enable the production and auxiliary facilities which only indirectly support the production. The construction costs of such auxiliary facilities are often roughly estimated because they do not immediately contribute to mineral extraction. The research project ‘Development of a systematic cost-calculation method for building services in underground mines’ seeks to address the question: ‘Can the construction costs concerning fixed auxiliary facilities be neglected e.g. within a prefeasibility study?’ The presentation will show the monetary relevance and significance of these auxiliary facilities and introduce a guideline for cost estimators. PROBLEM DEFINITION The overriding interest of an underground mining operator is to exploit the commodity with the maximal quality by minimum cost and time expenditure. If a new operation shall be installed, it has to promise profitability. Therefore, predictive economic feasibility studies are performed in advance of installation. Herein, all cost expenditure for installation and operation of the future underground mine is determined and compared to the expected income by selling the raw material. The described interest of the mining operator is the starting point of the research project ‘Development of a systematic cost-calculation method for building services in underground mines’. While economic feasibility studies for future operations are focused on the profitable exploitation of raw materials and the efficiency of the accompanying necessary production processes, auxiliary actions are only considered rudimentary. Necessary production processes, as well as auxiliary actions regularly require classical building services, which are normally performed in construction business on the surface in the same manner. By performing building services like masonry or concrete works in underground mines, fixed facilities shall be set up in order to enable or support the raw material production. Production enabling fixed facilities are varying from small concrete foundations for conveyor belts or other infrastructural elements to upstream processing plants situated in the mine workings. While such fixed facilities are essential parts of the production process chain, supporting facilities underground shall increase the efficiency of the mining operation. Workshops, control rooms and social installations are only a few examples for supporting facilities. Those could be situated on the surface as well, but the efficiency increases significantly by installing them underground. Especially supporting facilities are evading from the main interest of the mine operator, since they are only indirectly connected to the production process. The building costs are oftentimes only roughly assumed."

Jan 1, 2017

By Bruce Cavender

Production managers look to innovative practices and equipment to reduce operating costs and improve efficiency. These innovations apply to both technical and social aspects of production operations and may be high-tech or low- tech in nature. They may be based on the implementation of a few large-scale "breakthrough projects or numerous small-scale activities, depending on the availability of capital funding and the company's past experience. Successful managers systematically identify innovative opportunities that capitalize on their organization's expertise. They quantify the associated benefits and risks and then manage the implementation of selected innovations to minimize cost and uncertainty. They monitor the results of the innovation after it has been implemented and adjust operating and managerial practices as necessary to maximize the innovation's benefit.

Jan 1, 1998

By Hélio Blak

The Paranapanema Group was created in February 1996 when a group formed by the Brazilian pension funds acquired four companies dealing with nonferrous metals. The new Paranapanema Group, basically related to the tin and construction business, became the sole Brazilian primary copper producer, the second zinc producer and one of the most important producers of copper products, mainly tubes and fittings. To put together such different companies, managed before by family groups and with different cultures and principles, was and still is a big challenge. The strategy of developing and consolidating it as an homogeneous group is based in three pillars: an increase in production, quality and technological improvements on products and market mix and a permanent cost reduction program, using all the potential synergies founded.

Jan 1, 1998

By A. Pradakar, J. G. Groppo, J. W. Leonard

All coal transportation systems from the coal face to the final point of use would become more productive if additional tonnages, obtained through improvements to bulk density, could be placed in fixed volume containers such as scoops, shuttle cards, trucks, barges and ships, as well as conveyors. This paper reviews previously reported work where the treatment of coals with small amounts of mining chemicals (0.12 to 0.28 kg/t or 0.25 to 0.56 lbs/st) during lavoratory testing was show to increase loaded coal bulk density by about 15%. The latest bulk density enhancement findings to develop from ongoing research involving underlying chemical and physical theory together with the added use of simple mechanical excitation are discussed.

Jan 1, 1995

This paper discusses the type of scaling operations presently in use in underground mines. It defines a scaling factor that is expressed as the area necessary to scale to extract 1 t (1.1 st) of ore. The problems associated with conventional scaling methods are discussed as well as recent developments in mechanized hand-held scaling de- vices and methods of loose detection. The elements of the scaling process are further analyzed. The conception and design of a mechanized scaling device, developed at Universite' Laval is also described. The results of field tests conducted in Quebec hard rock mines are presented. The experimental findings show that the mechanized hand-held scaling device shows potential in improving the productivity and safety of underground mining operations.

Jan 1, 1996

By Chinmoy Sarkar

Mining organizations have been trying to employ best practices at exploration, exploitation and processing level to increase productivity in the supply chain. Traditional techniques of cost control can no longer meet the ambitious target of mine managers. An integrated perspective of Mining Value Chain with enterprise-wide application of information technology (IT) ensures the ability of every mining processes to improve energy, land, capital and labour resource performance while continuing to cut costs and achieve profitability. IT offers enormous potential in mining industry at shaping entirely new opportunities to create value. This paper characterizes important entities of Mining Value Chain and attempts to provide a vision on how IT can transform the mindsets of industry managers addressing the needs of the customers.

Jan 1, 2002

By J. A. Dille, J. P. Hand, J. D. Brown

The purpose of this paper is to inform members of the coal producing and consuming community about techniques used by The Carter Mining Co. to control product quality at a large surface coal mining operation. During the early years of mining operations, coal quality received adequate attention but the company's main emphasis was to build up its production rate and minimize mining costs. While these goals are still of prime importance, coal quality has received additional attention in recent years. An objective that no coal shipment should exceed any contract or company-imposed coal quality specification has been successfully met. To implement this guideline, geology and coal quality modeling procedures were improved, in-pit drilling and blending programs were refined, and detailed shipment procedures were developed.

Jan 1, 1987

By B. Bringhurst, J. J. McClelland

A filter consisting of a synthetic fibrous material has been determined to be a viable alternative to the wire mesh panels currently used in irrigated filter dust collection systems. An extensive laboratory investigation of the material showed that it removed a higher percentage of both respirable coal and quartz dust from the air entering a collector than did the flat and pleated wire mesh panel designs. This improvement in dust collection efficiency reduced the amount of coal and quartz dust discharged from the collector exhaust by approximately 44%. Since continued exposure to excessive levels (>5%) of respirable quartz dust presents a severe health hazard, this alternative filter medium could be of use to those mines required to comply with more stringent dust standards due to quartz.

Jan 1, 1992

By Louis L. Sirois, Kwang S. Moon

The flotation mechanisms of various flotation machines are briefly reviewed. The counter current column flotation mechanism is described in more detail. The merits of counter current column flotation include; improved metallurgical performance in terms of grade and recovery, effective cleaning action in the long cleaning zone with a blanket of fresh water, smaller floor space required due to the vertical configuration of a flotation column, low capital, operational, and maintenance costs due to the absence of moving parts and finally, easier flotation control due to the simplified circuit. The results of column flotation studies on various minerals and coal at CANMET are discussed. Some of the industrial experiences with the Canadian flotation column on various sulphides, oxides and coal are also presented.

Jan 1, 1988

By Allan J. Breitenbach

Heap leach operations provide a low-cost method for recovering gold, silver, and copper metals from low grade ore materials. The processed ore materials are stacked in controlled lifts on a lined pad facility for heap leaching. A controlled barren solution is applied to the heap ore surface by sprinkler or drip emitter irrigation, and ore metals are leached into the solution for collection and extraction in plant process facilities. The leach pad and solution collection facilities are lined with impervious materials for containment of all process solutions. The liner system typically includes a composite geomembrane and clayey soil liner with a protective drain cover fill to maximize solution recovery and protect the underlying groundwater conditions. This paper discusses the types of pad liner systems currently used by the mining industry and the "good, bad, and ugly" lessons learned in engineering practice over the last 10 years in the design and construction of heap leach pads.

Jan 1, 1999

By H. P. Hatch

Ash is a material that many people leave to nature to handle. Others sometimes sweep it under the rug to be disposed of by someone else. In our business we cannot do either. In fact the American Electric Power System spends many millions of dollars in plant investment costs to collect the material, and then many more millions to dispose it. In 1965 alone the coal fired steam generating plants in., the AEP System produced approximately 2,400,000 tons of ash, enough to fill 40,000 coal cars which would extend as a single train across the entire states of Ohio and Indiana. Even though our present ash production is large, this is only the beginning when we forecast the future growth of our system. By 1980 it is estimated that our generating capacity will expand to about three times its present size, and with coal as our primary source of fuel our ash production will increase proportionately to about 7 million tons a year.

Jan 1, 1966

By Michael Harris, David Mosch

The numerous small high grade gold and silver deposits of the Front Range Mineral Belt have been uneconomical because of the high costs of mill construction, transportation, and smeltering. Processing of these ores must be simple, cheap, with satisfactory recoveries, and be environmentally acceptable. Vat leach with direct electrolytic recovery satisfies these parameters. A battery of testing was conducted utilizing bottle and bucket tests. A five ton vat leach with direct electrolytic recovery gave excellent results while a five ton heap leach proved impractical due to channeling.

Jan 1, 1987

By M. Heger

February 2, 1999 marks a milestone in earth-moving technology at the San Miguel Lignite Mine. It was on that date that The North American Coal Corporation (NAC) took delivery of three Leica Dozer 2000 GPS grade control systems for use on its bulldozers. The primary reason for the purchase of these grade control systems was to prove that GPS technology could safely and economically be utilized on heavy equipment to assist operators in defining grades. If these properties were successfully demonstrated, the ultimate vision of the project was to expand the system to a point were GPS would become the primary means of providing grade control information to the mine’s heavy equipment operators. Twenty nine months and more than $500,000 later this vision was realized when the final bulldozer operating at the San Miguel Lignite Mine was equipped with Dozer 2000. Presently North American Coal has a total of nine Dozer 2000 GPS grade control systems at San Miguel providing cut and fill information to operators 24 hours a day. These grade control systems have allowed the San Miguel operation to increase safety, reduce costs, improve operator attitude, and better ensure environmental compliance. This article discusses both the nature of these benefits and some of the issues that had to be dealt with along the way.

Jan 1, 2002

By Shemek Oginski

The 5 km (16,194 lf) of 6.1m (20 ft) diameter TBM driven tunnel built by the J.F.Shea Co. will serve as sewage overflow storage. The TBM tunnel and four connecting tunnels excavated by drill and blast methods in hard granite will remain unlined. Based on the Geotechnical Baseline Report (GBR), the Contract documents provided a design with no required pattern of rock bolts, no probing, no pre-excavation or consolidation grouting, and lastly, no final lining of the tunnels was deemed necessary. This paper will provide a general overview of these topics with the emphasis on the actual ground conditions encountered versus the projected conditions provided in the GBR and how the GBR reflected the design of the project. Proposed modifications to the temporary and permanent ground support will be presented and the necessity of probing and pre-excavation grouting will be evaluated.

Jan 1, 2005

By Robert R. French

Beneficiation of-low-grade nonmetalliferous mineral deposits by electronic color sorting is currently undergoing a period of rapid development. For those deposits in which the specific gravity, strength, soundness, electric and magnetic properties of the ore and gangue are similar the possibility of separation by color, reflectivity, or fluorescence offers hope for utilization of much poorer quality ore than previously thought possible. For those ores in which consistency of color is required or for which a dry process is preferred, the electronic color sorter is particularly adaptable. Electronic color sorters were first designed to process agricultural products and were small low-capacity units. However, the recent introduction of larger machines designed to process 6-in, diameter ore at a rate of 30 to 50 tph (Anonymous, 1966a), has brought color sorting into the capacity range required by many mineral producers.

Jan 1, 1967

By Paul H. Johnson

Resource Engineering and Development, Inc. is desigining and building a portable 150 to 225 tpd, flotation-cyanide leach plant with unitized, skid-mounted components. This plant design, with its portability, low capital investment, and high recovery of silver and gold from many partially oxidized ores, is well suited to treat many small, highgrade deposits, old waste dumps, and old mill tailing piles. A description is given of flotation and/or cyanide leach tests run on 18 partially oxidized, newly mined ores; waste dump materials; placer slimes; and old mill tailings.

Jan 1, 1981

By Daniel Lakovic

"Mining operations can create a negative environmental impact, especially when considering the tailings that are produced through the processing of ores. Tailings are finely grained residues that form sludges. The tailings are deposited into giant basins, or sludge ponds, where they create a burden on the environmentby limiting the use of processed water.Tailings are one of the most important environmental liabilities for mining operations because of their large proportion in relation to the ore mined — generally 90 to 98 percent. To get to the valuable minerals, mining companies must move large amounts of rock. The rock is ground and then treated, usually with the addition of chemical solutions and large amounts of water. The lower the concentration of the valuable resources, the greater the proportion of accumulated excavated material sludge.Sustainable tailings management requires responsible handling, making it one of the mining industry’s greatest challenges. The proper technology should include consistent control of the environmental risks and impacts, as well as a proper relationship with the communities that surround the mining operations.The tailings, which can remain partly contaminated with chemicals, are pumped into the large sludge basins, which are secured by earthworks. During the mining operations, the basins must be stable enough to withstand the pressure of the stored excavated material. The storage option is still used, but it has failed on occasion. And when it does, it increases the risks to the environment and binds the unused process water. The more complex the availability of fresh water required for industrial use and for human consumption and their economic activities — for example, farming and agriculture — the more complex the conflicts that have the potential to shut down mining operations. With modern separation technology solutions, it’s possible to process the sludge and recover the processed water. However, the responsible use of the water is critical. Therefore, mining companies must rely on technologies that allow for proper reclamation of the water, whether re-using in their own processes or treating it to return it to the environment."

Dec 1, 2018