Search Documents

By K. N. Han

The leaching behavior of palladium in ammoniacal solutions was investigated by using the rotating-disk technique in an autoclave. The study included the effects of rotation speed, temperature, oxygen pressure, composition of ammoniacal solutions and catalysts on the overall leaching rate. The dissolution of palladium in ammoniacal solutions was discussed in terms of the thermodynamics and a kinetic model. Even though the Eh-pH diagram suggests that palladium metal can dissolve in ammoniacal solutions at room temperature, it was found that the dissolution was very slow at temperatures below 100 °C but was significantly improved at higher temperatures. It was also found that the rotating speed of the palladium disk had no effect on the leaching rate. The apparent activation energy was found to he 69.7 kJ/mole. Based on the results obtained, it was concluded that the dissolution of palladium is controlled by chemical reaction.

Jan 1, 1999

By Robert M. St. Louis, Janet M. Edgecombe

The Mercur Mine's autoclave is an alkaline pressure oxidation system, operating at 220°(428°F) and 3061 kPa (444 psig) (total). Up to 725 metric tons (800 st) of ore, grading 2.02 g per mt (0.059 oz/st) Au and containing 1 to 2% sulfide sulfur, are treated daily in this circuit. A mineralogical and chemical investigation was initiated to locate the cause of lower than anticipated gold recoveries. Greater than 70 wt. % of reduced sulfur is oxidized; therefore, the autoclave is operating at specification. The low recoveries were attributed to increased concentrations of organic carbon in refractory ore. Activated carbon concentration in the attached CIL circuit was increased from 15 to 40 g per 1, leach temperature held below 21°C (70°F), and carbon flow changed to counterflow. These measures resulted in gold recovery improving from 75 to 82%.

Jan 1, 1990

By Pramod C. Thakur

Sixty countries around the world mine about 5000 million tonnes of coal annually and simultaneously produce nearly 25 million tonnes (36.8 Gm3) [One tonne of methane at a temperature of 15°C and a pressure of 760 mm of mercury has a volume of 1471 cubic meters.] of methane. Many of these coal mines are very gassy and require methane drainage prior to mining as well as during mining. In spite of significant differences in the geology and reservoir properties of the coal seams, several methane drainage techniques have found universal application. The paper describes various techniques currently in use and their efficiency in recovering methane from mines. It appears that the application of state-of-the-art techniques, developed mostly in the U.S.A., can considerably increase the efficiency of methane recovery and improve the safety of mines throughout the world.

Jan 1, 1997

By J. F. Stenebråten, W. P. Johnson

Carbonaceous material (CM) from the Barrick Goldstrike Mines, NV, was characterized with respect to its gold sorption (preg-robbing) and gold recovery behavior. The breadth of graphite peaks measured by X-ray diffraction were used to calculate crystallite dimensions (002) of the CM. The (002) dimension was found to vary inversely with preg-robbing activity and directly with gold-recovery behavior, indicating that the degree of graphitization (maturation) experienced by the carbonaceous material is correlated with gold-loss during ore processing. The inverse correlation of preg-robbing activity was improved when percent preg-robbing was regressed against (002) crystallite size and carbon content. The (101) crystallite dimensions of all samples were calculated from laser Raman analysis, and were not found to correlate with preg-robbing behavior of the CM. BET surface area and micropore size distribution results were affected by grinding history, negating comparison of these characteristics between samples.

Jan 1, 2000

By V. T. McLemore

NMBGMR has been collecting data on uranium mining districts, mines and mills since it was created in 1927 and has converted years of historical data into a relational database that can be imported in ArcMap. The database includes information on mining districts, mines, mills, geochemistry, photographs, and bibliography. The available data includes location, production, reserves, geologic, geochemical, resource potential, and other data. The NURE stream-sediment data provides geochemical analyses for >27,000 samples collected in New Mexico during 1970s. The NURE hydrogeochemical data provides analyses for water samples. ArcMap includes location of individual ore bodies as polygons and incorporates the mines and NURE data as individual site locations. The purposes of these databases are to provide computerized data that will aid in identifying and evaluating resource potential, resource development and management, production, and possible environmental concerns, such as physical hazards (i.e. hazardous mine openings), indoor radon, regional exposure to radiation from the mines, background geochemical data and point-sources of possible pollution in areas of known mineral deposits.

Jan 1, 2010

By Kourosh Shahriar

The occurrence of rock falls in underground coal mines entails detrimental effects as fatal or non-fatal injuries on workers, stoppages in mining operations and breakdown of equipment. In this paper, a risk assessment approach on the basis of a decision analysis trend is employed in order to assess the possibility of and manage roof falls. Risk is then assessed by determination of likelihood of occurrence and the cost of consequences (outcomes). In this regard, collected real roof fall data from Tabas and Kerman coal regions comprising of several underground coal mines are used. It is concluded that the annual accidents due to the roof falls occurrence in the all investigated mines are so high that it is economically feasible to improve the support systems and to implement a suitable educational program as well as an accurate supervision and other elements of safety management.

Jan 1, 2009

By Claude M. Moreland

It is common practice when thermally drying coal from wet coal preparation facilities that the coarse +0.5mm fractions and fine fractions (-0.5mm) are combined and fed to a thermal dryer. There are very good reasons for this concept. The coal feed is much easier to handle in this condition for it is not as likely to stick inside the dryer or hang up in the material handling equipment, and is easier to feed and discharge. However, it is generally only the -0.5mm fines that really need to be dried. The +9.5m fraction of the cleaned coal will leave the dewatering screens, or drain and rinse screens, at an acceptable surface moisture, probably 5 or 5 ½ percent. The 9.5m x 0.5mm mesh fraction can be centrifuged to about 8 percent. The -0.5m fines can range from 18 to 22 percent or more, depending upon the type of equipment employed to dewater, and upon the size distribution within this size range.

Jan 1, 1982

By Allan M. Hale

Taconite tailings reclamation, especially the stabilization of tailings ponds, .dams, and slopes, can be effectively accomplished through the use of appropriate vegetation. Utilizing vegetation provides both aesthetic and ecological enhancement of a site while at the same time protecting tailings structures against wind and water erosion. Generally, the methods and techniques for establishing vegetation are well known; however, there are many site-specific factors that can alter a particular reclamation approach. Those factors include slope gradient, tailings material size, solar exposure, and physical and chemical properties of tailings. In addition to the site-specific factors, variations in climate, geography, and physiography of a region can have a pervasive influence on the success or failure of a revegetation program. Both the site-specific and regional factors control reclamation planning in such areas as plant variety selection, methods and times of plants establishment, maintenance techniques, and subsequent monitoring methods. As a result of this multifactor relationship, it is important to establish a data base that identifies both the site-specific and location conditions in order to tailor the reclamation plan to the specific area. When an appropriate data base has been collected, detailing the various site-specific and regional factors that will influence a revegetation program (in the absence of previous testing), it is very beneficial to apply experimental techniques to develop the reclamation plan for a specific site. The reclamation plan for a specific site may include several techniques adapted for the differences found within the specific site as the result of topographic or other influences. Considering this, the Reserve Mining Company and Dames & Moore undertook to develop a successful reclamation plan based on a detailed test plot program conducted at the Mile Post 7 location.

Jan 1, 1980

By Matteo Cortinovis, Giuseppe Gelmi

"INTRODUCTIONEdilmac dei F.lli Maccabelli (hereinafter referred to as Edilmac) has recently developed a special civil engineering application using the Raise Boring technology with the assistance of Inrock MGS (Magnetic Guidance System). Applying the Paratrack Magnetic Guidance System coupled with a directional mud motor to the drill string allows a better accuracy compared to standard drilling, as showed in our tests. This is the first time the Paratrack System has been applied to the Raise Boring technology. RAISE BORING METHOD STATEMENT The Raise Boring technology was born in North America during the Sixties. In 1962, Ingersoll and Robbins were the first companies to produce Raise Boring Machines (RBM). The technology was first used in the underground mine industry, in order to bore ventilation shafts and passes through different levels, thus reducing the cost of haulage. The Raise Boring method is only feasible in stable rock conditions. The Raise Boring method consists of drilling a small diameter pilot hole that reaches a tunnel located at the bottom of the drilled hole. Once the pilot hole reaches the tunnel, a reamer head is installed at the end of the drill string and pulled up, creating the hole with the designed diameter (Figures 1 and 2). The main equipment, which is required to perform Raise Boring activities, is the following: •,An RBM; •,A tricone bit; •,Drilling rods; •,A reaming head; The standard mucking of the pilot hole is done with water or bentonite mud. For the last 30 years, Edilmac has developed a mucking process, which uses compressed air with the addition of foam or a small amount of water for dust control.Pilot hole tricone. The drilling of the pilot hole is usually performed with a tricone bit having a diameter between 11” (27.61 cm) and 15” (38.10 cm) (Figure 3). High strength rods. They generally have a diameter ranging from 10” (25.40 cm) to 12 ?” (32.70 cm) (Figure 4), depending on the length and the final diameter of the shaft."

Jan 1, 2016

By Nick Chlumecky

INTRODUCTION Column-type supports are used to prevent roof falls in underground excavations. The first individual column supports were made from timber that was cut to fit the irregular heights of mine seams. Because the seam height of the material removed varied throughout the mine, timber posts generally could be used only once. During the I 920s, steel friction props began to appear in British and European mines, and, by the 1950s, thousands of these props were being used. However, the steel friction props were heavy, difficult to install, and difficult to recover. Furthermore, the friction props could not be preloaded, and their yielding behavior was rather erratic. In 1946, hydraulic props were introduced in En¬gland, and, within a few years, they replaced friction props throughout Europe. The first application of hy¬draulic props in the United States occurred in the 1950s, during early experiments with longwall mining. Modern technology and high-production mining procedures have combined to make the use of hydraulic props a very acceptable method of providing temporary heavy-duty support for production areas. In areas such as development headings, where only modest roof loads are expected, lighter-duty jackscrews, ratchet jacks, and light hydraulic props are used. ADVANTAGES OF HYDRAULIC SUPPORTS The acceptance of hydraulic supports has been wide¬spread during the past 25 years, proving their reliability and effectiveness in preventing roof falls. Some of the advantages provided by hydraulic supports are: 1) Individual hydraulic props can be installed within 30 sec, resulting in a minimum exposure of per¬sonnel and equipment to an unsupported roof. 2) Hydraulic props can be preloaded to more than 4.5 t (5.0 st), increasing the frictional resistance between the rock strata. Thus, the roof is kept tight, improving the behavior of the unsupported ground. 3) If gradual roof sagging or bottom heaving im¬poses an irresistible force, the hydraulic prop yields gradually and continues to support the ground. 4) The support capacities of the hydraulic props most widely used range between 10 and 20 t (11 and 22 st). Their support capacities are maintained during yielding to an irresistible force. 5) Hydraulic props can be recovered rapidly. Where no other supports are provided for the roof, as in pillar¬ing operations, the hydraulic props can be recovered by remote means. 6) The length of hydraulic props is readily adjust¬able allowing them to be reused in seams where roof height varies. 7) Studies of mining operations indicate that the use of hydraulic props increases both personnel safety and mine productivity. DESCRIPTION Figs. I and 2 illustrate typical hydraulic props used in mines in the United States. Fig. I illustrates a prop

Jan 1, 1982

By Harvey W. Parker

Our industry has developed to the skilled, experienced and productive industry that we now enjoy as a result of the visions of great engineers throughout history, but, in particular for their visions in the last 1 centuries. Unfortunately for our forefathers, the technology lagged so far behind that these exceptional visions could not be realized for decades, sometimes for a century. All that has changed in recent time and many bold and visionary projects can now be constructed and operated because of dramatic advances in technology. Before, say, 1950, tunnel technology developed very slowly. However, technology is now developing at such a fast rate that planners and decision makers are challenged to stay ahead. Moreover, new technology will develop during the lifetime of any project that can dramatically improve under-ground space projects. One of the best examples of this technological advancement is that of closed-face TBMs which now make tunneling feasible in previously impossible ground conditions. Since it usually takes a decade or more to plan, overcome environmental and political issues, construct, and put into service major projects, planners and designers are challenged by the changes in technology that occurs during the long time span of planning and construction. This is particularly true of large infrastructure projects such as transportation, water and wastewater systems and other major underground schemes. Also, since the serviceable life of many of these tunnels is often over one century, planners must consider not only lessons learned from the past but also what new concepts and innovations may develop over an extremely long time. These and other issues create a great challenge to planners and illustrate the great importance of careful but creative vision and flexibility during planning of long-term tunnel and underground space projects.

Jan 1, 2008

By R. Bissonette, C. Sunderman, R. Jacksha

The ability of wireless systems—e.g., voice communication, proximity detection, tele-remote operation, telemetry, etc.—to function satisfactorily (coexist) in the presence of other wireless systems is critical to the safety and health of mine workers. The failure of wireless systems to coexist could result in the delay, corruption, or outright loss, of critical data, voice, or video information. However, no mining-sector-specific regulations, standards, or guidelines exist to ensure the safe coexistence of wireless systems. This paper introduces the concept of wireless coexistence, implications in the mining industry, and the National Institute for Occupational Safety and Health’s (NIOSH’s) research approach to develop guidelines and recommendations to ensure safe wireless coexistence.

Feb 1, 2023

By S. Mathur

Polyacrylic acid (P AA) was evaluated as a selective flocculant for dolomite-apatite system. P AA of 4 million MW was found to flocculate both dolomite and apatite. However, their flocculation behavior was significantly different with 450,000 MW PAA which was the lowest molecular weight fraction capable of flocculation. In single mineral tests, at a dosage of 2kg/t 90% of dolomite and 35% of apatite flocculated. Selectivity was achieved in mixed mineral tests where apatite of 90% grade at 70% recovery level was obtained in the concentrate from a feed consisting of 80:20 mixture of apatite and dolomite. The dolomite rejection was about 75% which corresponds to 1% MgO in the concentrate.

Jan 1, 1995

By K. S. E. Forssberg, J. A. Jirestig

Laboratory investigations on the possibility of using magnetic separation for the recovery of sulfide minerals have been reported. A survey of several sulfide ores and flotation concentrates indicated that, in most cases, magnetic separation is not a suitable primary beneficiation method. However, encouraging results have been obtained in concentrate purification. At the Boliden complex sulfide ore concentrator in Garpenberg, Sweden, an Allis-SALA Mark III carousel High Gradient Magnetic Separator (HGMS) is used with a small flotation circuit to recover sphalerite lost to the galena concentrate during lead flotation. After four years of refining the HGMS process, there has been an increase in zinc recovery and an enhancement in the quality of the lead concentrate.

Jan 1, 1994

By John J. Dran

In recent years, market rates of interest have risen well above their historical long-term average. Also during this period, the short-term variability of interest rates has been greater than in prior years. Interest rates have a significant effect on the operation of our economy. They influence the extractive industries in a number of ways. Their major long- range impact is on investment decisions - specifically the valuation of mineral deposits. An understanding of the factors that influence interest rates is important to the engineer or businessman who makes the investment decisions for the mining company. The effect of changes in the market rate of interest on the value of mineral reserves is critical to the future financial success of the mining enterprise. The most common simplification of the factors determining the level of interest rates is that they are a function of the demand for and the supply of money. While this is an oversimplification, most businessmen would be hard- pressed to provide a better explanation. The purpose of this paper is to explore certain fundamental economic aspects of interest rates and to examine their effect on the analysis of investment in mineral deposits.

Jan 1, 1975

By William T. Ingram

Early in the 60's the author served as Chairman of the Engineering Foundation's Coordinating Committee on Air Pollution Research. One of our objectives was the development of a study on the measurement of stack emissions. Three publications of the Foundation resulted from these efforts to focus attention on the stack sampling problem.1,2,3 Two of these were annotated bibliographies covering 197 references. The third reported the results of a workshop meeting at which some 21 individuals from research institutes, industry and government discussed the possible and probable areas of research that would add to or increase the ease, precision and utility of sampling gaseous and particulate matter emitted from stacks. The American Society of Mechanical Engineers has had in its Power Test Codes a Standard Code for Determining the Dust Concentration in a Gas stream4 since 1941, The American Industrial Hygiene Association has published, in its Air Pollution Manual,5 a Section on Stack Sampling. Industry and regulatory agency requirements for stack sampling have utilized some modification of the alternatives in methodology. There has been ho single guide to stack sampling that met the needs of those who have the need to know.

Jan 1, 1970

By J. Wiese

Recently the operating philosophy at concentrators processing platinum bearing ores has started to move from a recovery dominated system to one in which the production of high grade concentrates at the expense of some recovery would provide greater benefits in the further upgrading of the platinum group minerals (PGM). The low grades usually obtained are associated with the presence of naturally floatable talcaceous gangue minerals in all PGM ores. Polysaccharide depressants such as guar gum and carboxymethyl cellulose (CMC) are used to improve the grades of the concentrates. Recent testwork has shown that the use of high depressant concentrations can prevent any naturally floatable gangue from reporting to the concentrate. The only gangue present in the concentrates would be due to its entrainment in the froth. Under these conditions much higher grades can be achieved. The sulphide minerals themselves, however, become susceptible to depression at high depressant concentrations. This work examines how the recovery of sulphide minerals in two Merensky ores was affected by the type and concentration of the collector in the presence of high depressant concentration (500 g/t) and that the response of the sulphide minerals was also dependent on the type of depressant used (guar or CMC).

Jan 1, 2009

By J. R. Pennington

The town of Green River, Wyoming, is located along the Green River on an arid plateau at a elevation of 6,300 feet. Green River has become the center of a booming soda ash industry. The rapid development of coal, oil, and gas resources, coupled with the soda ash boom, have created growth pains for the area. Green River and Rock Springs have experienced a 20-25% population increase in 1973 alone. However, public officials, business leaders, and local citizens are taking positive steps to ease the problems relating to housing, schools, medical services, and recreational facilities. What Is Soda Ash? Soda ash is one of the most widely used chemicals in the world. It is an important raw material in the manufacture of glass, paper, soap, petroleum products, metals, chemicals, pharmaceuticals, plastics, and a host of other items essential to every day living. In ancient times, soda ash was obtained from water solutions of various desert earths. Later, it was produced by leaching the ashes of wood and seaweed. For the past 100 years, it has been manufactured by the ammonia-soda process, which employs large quantities of salt, limestone, and coal as raw materials.

Jan 1, 1974

By K. E. Yassin, A. Yehia, M. Amar

Phosphate ores are the source of many commodities, such as phosphorus element, P2O5 and fertilizers. Discarding a large percentage of fine phosphate particles produced as slimes during phosphate ore processing represents a severe environmental problem, besides making the beneficiation process uneconomical. The phosphate industry is interested in a process that is efficient, with high grade and high recovery; ensures economical feasibility, with low operating cost; and is environmentally sound, with low toxicity. Numerous investigations have been conducted to try to find better processing techniques and reagents. However, reagent requirements and recovery limitations may be so high that the end does not justify the means. Reagents of biological origin are of special interest because they offer specific interactions with minerals, reduced operating costs, environmental acceptability and flexibility in adaptation. Recently, there has been a growing interest in using microorganisms as flocculants for mineral fines and as flotation collectors. 

By Jennifer King, Julius Strid, Steve Brandon

The Upper Hidden Basin Diversion (UHBD) tunnel was driven approximately 1.2 miles by the drill-and-blast method primarily through massive granite bedrock geology for the Kodiak Electric Association, Inc. (KEA) in Kodiak, Alaska. The tunnel was driven from both portals with a constant 11-ft straight-leg horseshoe cross-section. The design and construction of the tunnel was driven by logistics and weather conditions due to its remote location and the rugged terrain of the project setting. This paper will discuss the successful completion of a challenging project over a ve-year period from preliminary planning through the design and construction phases.

Jun 23, 2024