Search Documents

"A cationic surfactant, tetradecyl tributyl phosphonium chloride (TTPC), was first used as a collector. Flotation characteristics of muscovite using TTPC have been investigated through flotation tests. And dodecyl trimethyl ammonium chloride (DTAC) was tested for comparison. Their adsorption mechanisms on muscovite surface were clarified using zeta potential measurement, DFT calculation and molecular dynamics (MD). The flotation results indicate that the recovery of muscovite decreases when the pH increases in the presence of surfactants. When a maximum of recovery was reached, the dosage of TTPC was 2×10-5mol/L which was half of that of DTAC. Zeta potential measurements confirm that the TTPC displays a stronger collecting power than DTAC and is a superior collector for the muscovite flotation. DFT calculation and MD simulations show that TTPC interacts with the muscovite mainly through electrostatic attraction and hydrogen-bonding. The conclusions drawn from purely theoretical computations matched remarkably well with the experimental results. Keywords: Quaternary phosphonium salts; Flotation collectors; Flotation INTRODUCTION Muscovite mica is widespread in igneous, sedimentary and metamorphic rocks. It has the general composition KAl2(AlSi3O10)(OH)2. Muscovite mica exhibits perfect cleavage along the (001) plane, which exposes interlayer potassium ions[1-3]. In aqueous suspensions, the potassium ions readily enter into solution, leading to the development of a net negative charge on the (001) plane[4-6]. The surface of the muscovite mica is negatively charged at all pH > 1[7]. Due to the negative charge surface over the whole pH range of 2–12, the muscovite mica would not be expected to respond to anionic collectors in the absence of an activator. Conversely, the mineral is readily recovered using cationic collectors. However, until now, various amines and their derivatives (with N atoms as the center) are still the only available cationic collectors which still had their shortcomings such as weak selectivity, low flotation speed. Since few types of cationic collectors could be used, in some sense, the limitations of collectors are increasing significantly and the cationic flotation is facing more and more challenges. Quaternary phosphonium salts, as novel cationic surfactants, are widely used in antimicrobial, catalysis and surface modification field due to their biological activities, hydrogen bonding capability, stability and superior group electrical property[8-10]. There are a number of processes where quaternary phosphonium salt surfactants have shown better properties than quaternary ammonium salts and amines. Although the adsorption of quaternary phosphonium salt surfactants at the bacterium–liquid interface has been studied thoroughly, the case of adsorption in mineral surface has not been investigated thus far."

Jan 1, 2016

By David R. Maneval

At the turn of the century the keys to industrial success were coal and iron. At that time, Pennsylvania was the ranking mineral producer among the States and close to 90% of the Nations energy output was generated by coal. The growth of this Common-wealth into the greatest industrial State in the nation has been due to the huge resources of easily accessable coal found by the early settlers. It was the development of these deposits that provided the United States with a new source of fuel energy. For nearly a century, the Commonwealth was the chief powerhouse of our nation and the chief source of its industrial blood and bone. In 1928 it was truly said that coal was king in Pennsylvania. Pennsylvania that year mined a billion dollars worth of coal. A single train carrying this output would reach more than twice around the world at the latitude of Pennsylvania. Coal formed nearly 67% of the freight of Pennsylvania and was responsible for its four billion dollar iron and steel industry. Coal was the real reason why Pennsylvania although 32nd in size was second and not tenth or fifteenth in wealth, population and industry. Pennsylvania was slow to take-up her heritage as the greatest coal producing State in the union. But the knowledge that coal was present was not slow in accumulating. In fact the Indians were aware of its existence long before the white man arrived. They knew that many of the hills were underlain with black stones that would burn. It is reasonably certain that Arnold Viele, the first white man to cross the mountain in this State saw coal in them in 1692. But awareness was not enough. The population in these days was confined to southeastern corner of the State and the population at this time had little need or interest in the resources further inland. Pennsylvania anthracite was discovered in 1762 but was first regarded only as a curiosity. Commercial productions started in 1820. This stimulated the development of many native industries and extensive canal system and afterwards an elaborate net-work of railroads were constructed at great costs to bring the products of the hard

Jan 1, 1971

By H. A. Taylor

Bismuth, one of the heavier chemical elements, is a pinkish metalloid that is chemically related to antimony. It is a byproduct of lead and tungsten extraction and, to a lesser extent, of copper and tin extraction. Antimony is a metalloid and less heavy chemical element, an extraction coproduct of metals such as lead, silver and gold. While both bismuth and antimony are metalloids, their major uses are as chemical compounds. The most frequently updated resources that always cover bismuth and antimony are the Bismuth Advocate News (BAN) and link at www.basicsmines/bismuth and the frequently updated Basics Mines Update blog at http://basicsmines-update.blogspot.com. The Bismuth wiki on Wikipedia also can be very helpful.

Jan 1, 2010

By Erwin A. Morlan

Present methods of boring large hole mine openings are briefly reviewed. Factors that influence the design and choice of down-the-hole equipment for rotary drilling large holes are discussed. With formation drillability taken as a starting point, graphs and charts are given as an aid in the selection of bit load, circulation system, flow rate, drill stem, cutter design and rotary speed.

Jan 1, 1961

By C. J. Lewis

Commercial lime plants in the United States and Canada are depicted in Figure 1. The sources of lime available to Nevada and bordering states are rather few. Chemstar Lime has plants at Apex, Nevada and Nelsen, Arizona. Continental Lime, Inc. has plants at Tacoma, Washington, Townsend, Montana and Delta, Utah. However, Continental Lime has a new rotary kiln installation underway near Wendover, Nevada. This plant is scheduled to come on stream in the fall of 1989.

Jan 1, 1989

By J. C. Armbrust

The Morenci Open Pit Mine, located in south-eastern Arizona, is owned and operated by Phelps Dodge Morenci, Inc. The Mine has been predominantly a rail mine since its origin in 1937. However, beginning in early 1986, a program was initiated to phase out the rail mining operation and replace it with a more flexible and productive truck haulage scheme. This transformation from rail to truck haulage will be accomplished when the current in-pit crushing and conveying project is completed in late 1988.

Jan 1, 1988

By Wayne W. Murdy

Since 1993, Newmont has been actively growing through the development of three major foreign mining operations with a fourth under construction. The first project, Yanacocha in Peru began operating in October 1993 at a time when political and business risk in that country was considered high. In 1995, Newmont began operating the Muruntau Joint Venture in Uzbekistan, the first of its kind in the CIS. In early 1996, Newmont started operating the Minahasa mine in Indonesia. Now, in early 1997, Newmont is undertaking the construction of a $1.9 billion project in Indonesia and is completing a feasibility study with our partner for the development of a gold operation in Mexico. All of these projects have been considered "risky" by most standards, and Newmont has been very successful in all of them through risk mitigation programs including utilizing strong and successful in-country partners, concentrating on developing a strong national workforce with minimal expatriate employees, utilizing World Bank, EBRD and IFC financing and building and maintaining strong ties with host governments. This paper describes in more detail, some of the risk mitigation programs that Newmont has used to successfully grow the company through development of major foreign mining operations.

Jan 1, 1997

By Yuexin Han

The characteristics of comminuted hematite products using a high pressure grinding roller (HPGR) and conventional jaw crusher (JC) were comparatively studied by screening, optical microscope, scanning electron microscope (SEM) and Brunauer, Emmett and Teller (BET) techniques. Major properties investigated included product size distribution, particle cracks, specific surface areas and pore volumes. Results showed that in a closed-circuit operation with a screen opening of 3.2 mm, the HPGR and JC gave a similar P80, but the HPGR achieved a more uniform size distribution, more fines and a higher crushing efficiency. Three modes of cracks were identified, namely transgranular cracks, innergranular microcracks and intergranular microcracks. Transgranular cracks originated from shearing breakage. Innergranular and intergranular microcracks were generated by HPGR via the two main nonrandom breakage forms, preferential breakage and interfacial breakage, depending on their respective ability to endure stresses when mineral phases (particles) were loaded against each other. The BET values for the same-size fractions showed that HPGR products gave higher specific surface areas and more pore volumes than JC products. This indicates that HPGR-crushed products are easier to grind because of their high porosity and extra cracks.

May 1, 2012

By N. A. Karl, D. R. Wilburn

"This summary of international mineral exploration activities during 2017 draws upon information from industry sources, published literature, SNL Metals & Mining (SNL), an offering of S&P Global Market Intelligence (New York, NY) and specialists in the U.S. Geological Survey (USGS) National Minerals Information Center. Three types of information are reported and analyzed in this annual review of international exploration: 1) budgetary statistics expressed in U.S. dollars provided by SNL; 2) regional and site-specific exploration activities that took place in 2017 as compiled by the USGS and 3) regional events and legislation that affected exploration activities including economic, social and political conditions, which were derived from published sources and discussions with USGS and industry specialists. Commodity and regional compilations are presented in this summary. Because multiple sources were used to develop commodity and regional compilations, statistics may vary depending on the source and type of data that are being reported.The SNL data summarize budget estimates for worldwide exploration activities in 2017 for 30 nonfuel mineral commodities and metal alloys, based on company surveys. Surveys focused on precious metals (gold, platinumgroup metals (PGMs) and silver), base metals (cobalt, copper, lead, molybdenum, nickel, tin and zinc), bulk commodities (bauxite, chromite, iron ore, manganese, phosphate and potash), and other commodities (aluminum, antimony, diamond, graphite, heavy-mineral sands, lithium, niobium, rare-earth elements (REEs), scandium, tantalum, tungsten, uranium, vanadium and yttrium). Information on uranium exploration activities was included in SNL’s survey for the first time in 2007. Data on lithium, niobium, phosphate, potash, REE and tungsten were compiled for the first time in 2010, and scandium, vanadium and yttrium were added in 2014 because of their increased topical significance. Since 1999, companies with exploration budgets of $100,000 and greater were included in the SNL surveys. SNL budget estimates exclude coal, and oil and gas. The 2017 SNL mining company survey compilation was reported by SNL to include an estimated 95 percent of the world’s nonfuel mineral exploration budgets. The 5 percent that was not covered was accounted for by companies that chose not to participate in the SNL survey, private companies that do not publish their budget data, and government-funded exploration activities."

Jan 5, 2018

When a company like Lonmin, the third largest platinum producer in the world, is mining one of the most precious metals in the world, time is money. Every piece of equipment is expected to be in top shape because every minute of downtime can add up to lost profit. Two different types of platinum ore are mined and processed by Lonmin, namely Merensky and UG2. Merensky has a grade of 3.5 g/t (0.1 oz/st) and UG2 has a grade of 4.5 g/t (0.13 oz/st). The mine also produces platinum group metals (PGM), which consist of platinum, osmium, palladium, rhodium, iridium and ruthenium. Although South Africa has more than 80 percent of the world?s PGM reserves, these minerals are very scarce. Lonmin is considered a low-cost producer of these minerals, generating 21.5 t (694,000 oz) of platinum and 18.6 t (600,000 oz) of PGMs in 2012. So when the company?s Karee K3 concentrator plant in Rustenburg, North West Province, South Africa, was experiencing high operating costs on the transfer points, a solution was needed.

Jan 1, 2012

By Andrew Chegwidden, Tara Wilk

Construction of Shaft 17B-1, a part of The New York City water supply system, required an excavation of approximately 38 m (123 ft) through water-bearing overburden soil and more than 152 m (500 ft) of gneiss bedrock to make a connection to Water Tunnel No. 3. Ground freezing was the specified method to provide temporary earth support and ground water control for the overburden material. The ground freezing process relied on a supplemental geotechnical investigation and comprehensive laboratory testing of the frozen soil to evaluate the potential long-term creep behavior of the soil and the elimination of a temporary lining system. This paper describes that process as well as the drilling and installation methods of the ground freezing system. Additionally, the methodical system of excavation and insulation is discussed that permitted a safe and timely excavation followed by the installation of the permanent concrete liner.

Jun 13, 2023

By Arman Hazrathosseini, Ali Moradi Afrapoli

Fleet management systems (FMSs), as a pivotal part of any surface mining operation, need to evolve from conventional to intelligent systems because of both Mining 4.0 requirements and some shortcomings inherent in conventional methods. However, this novel transformation needs to be investigated technically and strategically. To this end, previously published research works on intelligent FMSs are explored to track the latest status of these third-generation frameworks within the surface mining context. Their underlying models are then compared in terms of five categories of allocation and dispatching features to pinpoint the technical gaps ignored. Having drawn the future lines of research, the present work then leverages the popular SWOT analysis method to outline the strengths, weaknesses, opportunities, and threats associated with the advent of these intelligent FMSs in mines of future. By and large, the analysis indicates that advantages outweigh disadvantages. Solutions are offered to address the existing weaknesses and threats.

Apr 1, 2024

By S. Chander

A mineral or metallurgical process uses various inputs, such as ores, energy and other raw materials, to make different products that fulfill societal needs. The processing of raw materials has changed in recent years due to the increased complexity of processing low-grade ores, intensifying competitiveness and greater constraints. For process improvement, various plant optimization and process modifications must be conducted under environmental, social, political and economic constraints. Processing research and education's success in meeting the process industry's future needs depends on an adequate balance between micro- and macro-engineering approaches. In its simplest form, macro-engineering is concerned with the "big picture," while micro-engineering requires looking at a subset of the process. So macro-engineering may be defined as an investigation of the larger or "whole" system to achieve the desired goals. And micro-engineering may be viewed as a quantitative investigation of a subset of the process, to determine cause-and-effect relationships within the subset. Two different approaches might be used in macro-engineering analysis. In one, the big picture may be viewed without a detailed knowledge of the subunits. With this approach, statistical tools are used to relate input and output parameters. Also, actual plant data or analog models might be used to obtain the desired information. The usefulness of such an approach increases with problem complexity. To attain the desired goals using the second, "model-based," approach, a detailed knowledge of the subunits is often useful and their interactions may be considered. In complex process analysis, the first of these approaches is more useful since less information is needed. However, it is also less exact and more likely to fail if there are significant changes in conditions and interactions. The second approach, on the other hand, is more exact, with greater predictive ability within the narrow subset being considered. Consequently, it is difficult and costly to conduct.

Jan 1, 1992

By C. J. Pritchard, R. E. Gundersen

I commend the authors on examining an interesting method of shaft lining and attempting to improve safety in a dangerous environment by remotely installing the shaft lining. It is important, though, to not trade off shaft lining safety for long-term mine safety by lining an intake shaft with combustible material. In many operations, the mine utilities are installed next to the lining of the intake shaft, supplying a possible ignition source if damaged or overloaded. Although the polyurethane studied in the paper is of relatively high density, no mention is made of the flame retardency of the samples. When exposed to heat, small amounts of polyurethane will melt and bum but are extinguished when the heat source is removed. If large surface areas of combustible polyurethane - a tunnel or mine shaft- are exposed to ignition heat sources that are not removed or extinguished early, an uncontrollable, fuel rich fire may result with high carbon monoxide levels, low oxygen concentrations, and greatly increased burning rates that can have devastating effects on the ventilation system and miners' safety. Although these heavy polyurethanes lend themselves to a "pouring" application around the annulus of the shaft liners and is a continuous process, past experience with atomizing and frothing polyurethane spray systems indicates a high degree of maintenance and operator attention to the nozzle1 delivery system. This may require more miner's time to be spent in the shaft maintaining the foam system, negating some of the safety advantages of the system. If polyurethane foams are to be used in mines, they must be of the highest quality available in terms of flame spread, heat emitted while curing, and contaminants emitted while curing and spraying. In addition, employees must be given adequate training and be thoroughly informed in all aspects of polyurethane foam safety procedures. As witnessed by our fellow miners in South Africa, we can accept no less.

Jan 1, 1991

By F. W. Pereira

The Montana Talc ore body was discovered in the summer of 1983, in the Gravelly Range, approximately 25 miles south of Ennis, Montana. Initial drilling indicated a plus-million-ton ore body of high-purity talc. Preliminary analyses were performed on the ore cuttings, .including chemical analysis, brightness measurements, and microscopic evaluations of the structure of the talc. The results indicated the talc was similar to that currently being marketed from Montana and probably would have good commercial value.

Jan 1, 1989

By Wisecarver D. W.

Today the longwall is getting increasing attention in the United States as an excellent way to mine coal. This is not to say it is the best way in every mine because conditions, capital costs, and markets may well dictate another method. However, operators with working longwalls are often showing preference by phasing out room-and-pillar sections and replacing them with longwall. In the United States there are about 90 longwalls in operating coal mines and the number is increasing. In Europe, 95% of underground coal mining is by longwall compared with only 5% in the United States. In the Western States about 25% of the underground coal mines use longwall mining. There is logic behind the increase in longwalling. Compared to room-and-pillar mining, straight single-pass longwall has important advantages that show up in underground coal mining in any part of the country.

Jan 1, 1978

By H. Zhu

Qualitative and interpretative information as obtained from geological and/or geophysical studies, in addition to precise measurement, is incorporated into the estimation process through an indicator variable. The indicator conditioned estimator is formulated as a cokriging and its expression is data value dependent as opposed to that of the traditional kriging estimators. The solution of the dual cokriging system pro-vides simultaneously an estimate of the unknown and an estimate of the conditional probability that the unknown belongs to a specific population or class. Being an unbiased and minimum-error-variance estimator by construction, the indicator conditioned estimator is better in the least square sense than the ordinary kriging estimator because it uses additional information carried by the indicator data.

Jan 1, 1989

By A. H. Balch

A physical elastic seismic model, based on the Peoria oil field was constructed and used to produce multi mode cross-borehole seismic data. Because this was a physical model, it was necessary to deal with a complex wave field consisting of compressional waves, shear waves, and converted waves. The recorded raw data were complex, have no resemblance to the inter-well geology, and were difficult or impossible to interpret. These unintelligible data sets were extensively computer processed. Detailed, accurate, images of the inter-well structure, and reflecting horizons were obtained as a result of this processing. This investigation demonstrates that excellent, accurate images of the inter-well geology can be obtained by skilled seismic cross-well data acquisition and extensive careful computer processing.

Jan 1, 1993

By Steve Kral

The Prospectors and Developers Association of Canada (PDAC) was established in 1932 in response to proposed regulations that would have threatened prospectors in Ontario. From there, the association grew to represent the interests of Canada?s mineral exploration and development industry. The PDAC?s mission statement reads: ?The PDAC exists to protect and promote the interests of the Canadian mineral exploration sector and to ensure a robust mining industry in Canada. The PDAC will encourage the highest standards of technical, environment, safety and social practices in Canada and internationally. ?Today, the PDAC?s 6,000 individual members include prospectors, developers, geoscientists, consultants, mining executives and students. In addition, the association?s membership includes 950 corporate members, representing senior, mid-sized and junior mining companies in addition to organizations that provide services and equipment to the mining industry. In 2010, the PDAC adopted its e3 Plus principles, a framework to guide its membership in responsible exploration.

Jan 1, 2011

By J. Seiter

Mining has always been among the most hazardous of occupations, and with the increasing demand for coal and minerals, safety in mines assumes even greater importance. Worldwide, underground miners are being exposed to noise and respirable dust hazards associated with roof bolt drilling. These hazards are now being understood to cause irreparable damage to the health of miners. The objective of this research was to discover if a Polycrystalline Diamond Cutter (PDC) drill bit generates less respirable dust and hazardous noise than a competing Tungsten Carbide (WC) bit, in dry vacuum drilling. In order to control the drill parameters the drilling tests have been conducted in a laboratory setting. The results were met by determining the quantities of dust and noise generated using each drill bit and analyzing those levels by using monitoring devices and software to collect the data. This paper includes information on experiment setup, equipment used, drilling parameters, and data collected. The test results suggest that there are noticeable trends that the PDC bits produce less dust than WC bits but more testing is needed to substantiate these trends.

Feb 23, 2014