Search Documents

By Tony Walsh

Australian Stock Exchange Limited (ASX) -ASX is ranked 9th in the Morgan Stanley Capital International (MSCI) Index – only 2.02% of that Index. -1520 companies – 400+ mining & mining exploration. -Over 50% of Australians own shares in ASX listed co.s -Disclosure standards play a vital part in providing investors with confidence, thereby building depth and liquidity in the market.

Jan 1, 2003

By J. M. Ekenes, C. A. Caro

"New approaches that increase hydrometallurgical recovery from refractory minerals in below mill cutoff -grade sulfide copper ore can add significant value, improve profitability and increase ore reserves. This paper describes the development and implementation of an engineered heap (EH) approach to leaching low-grade, chalcopyritebearing ore at Freeport-McMoRan’s mine in Morenci, AZ. The technical evolution of the engineered heap concept is described together with the challenges and benefits following implementation. Introduction The Morenci ore deposit, located in eastern Arizona, has been mined for copper for 140 years. Mineralization in the Morenci district consists of sulfides and oxides. To process these ores, Morenci operates concentrator and leaching circuits. Leaching accounts for two-thirds of the copper produced in Morenci. More than one-half of this leaching-derived copper production comes from run-of-mine (ROM) stockpiles. The largest category of material moved in Morenci is destined for ROM stockpiles and waste dumps. Materials that are not economic to mill or leach are designated “waste.” However, this designation can change based on improvements in extraction technology and commodity prices. Chalcopyrite does not leach well due to its refractory nature. For predominant chalcopyrite mineralized ore, copper recovery during a typical leaching cycle may be as low as 5%. For this reason, chalcopyritedominant ores below mill cutoff grade have historically been classified as waste. By incorporating advanced leaching technology to improve metal recovery from previously leach-resistant ore types such as chalcopyrite, the Morenci Mine has been able to reclassify substantial amounts of this “waste” to “ore.” Process chemistry Chalcopyrite copper extraction is temperature, oxygen and ferric dependent. The temperature is achieved primarily by pyrite oxidation (Eq. (1)) and secondarily by oxidation of chalcopyrite itself (Eq. (2)). The regeneration of ferric in solution can be enhanced by providing the appropriate acid and oxygen levels according to Eq. (3). In the absence of microorganisms, this reaction is very slow."

Jan 1, 2015

By T. S. Spicer

Inflammability and crossing point apparatuses were used to study the influence of increasing amounts of such inerts as ash, fly-ash, pyrite, limestone and Portland cement with several pulverized bituminous coals. The results indicate that it requires large proportions of inerts to substantially suppress the ease of ignition.

Jan 1, 1962

By David J. Akers

In past years, water drainage control in coal mines has been primarily directed on the basis of water quantity rather than quality. Due to the recent intense interest in total ecology and environment, emphasis has shifted to the point where the water exiting from a mining operation may be of better quality than when it enters. In most operations this has meant the use of treatment methods (neutralization) while the technology for the prevention of acid drainage is being developed or refined. To date, underground abatement of acid formation has generally been less expensive but also less effective than surface treatment of the mine water. It seems probable that total mine water pollution control will have to include both underground abatement and surface treatment methods. The general acid producing reaction involving the oxidation of pyrite - 2FeS2 (pyrite) + 702 + 2H20 ? 2Fe2S04 + 2H2SO4 - is well known, even though the individual steps are not clearly understood. The major implication of this reaction, that acid production can be eliminated by not allowing the contact of pyrite with free oxygen or water, has been well substantiated both in the laboratory (1,2) and in practice. (3) Underground abatement or control processes can be generally classified into two types: (1) the effective control or elimination of acid causing reactions within the mine, and/or (2) the reduction or prevention of water flow into and out of the mine. Recognizing the fact that these two types may be directly inter-related, this paper will, for the purposes of clarity and simplification, discuss each separately.

Jan 1, 1973

By M. E. Buzon, M. E. Gunter, B. D. McNamee

A Google search on talc asbestos yields more than 500,000 hits due to the growing number of civil lawsuits in this area. Historically, the litigation was centered on amphibole-containing industrial talc. There was no debate these talcs contained amphiboles, but the issue was the definition of asbestos and whether the amphiboles had an asbestiform habit. Ultramafic-hosted talcs, however, are formed in such a way as to not favor the formation of amphiboles in the talc, but they can occur in the surrounding black-wall. In these deposits, the serpentinite host rock is in direct contact with the talc, therefore, allegations can be made that non-asbestiform amphiboles or non-regulated serpentine group minerals can occur in the final products. We analyzed talcs from both metamorphosed carbonate- and ultramafic-hosted talc deposits using polarized light microscopy (PLM), scanning electron microscopy (SEM) with energy-dispersive spectroscopy (EDS), electron microprobe (EPMA) with wavelengthdispersive spectroscopy (WDS), transmission electron microscopy (TEM) with EDS, and powder X-ray diffraction (XRD). Compositions of minerals determined by EDS alone are not sufficient to confidently identify asbestos, despite common practices by some researchers. We emphasize, using both historical samples, and analyses of currently contested minerals, the importance of determining both the structure and composition of a mineral, as well as defining its morphology, before concluding whether it is asbestos.

Jan 1, 2018

By J. K. Pandey, ebashish Mishra, D. P. Mishra, N. K. Mohalik, S. K. Ray

The increasing demand for coal and depletion of shallow depth reserves are pushing towards deeper mining. In deeper coal mines with multiseam workings, the problem of ventilation surges many folds primarily related to air quantity requirement, heat, humidity and spontaneous heating/fire in goaved (gobbed) out areas. The paper describes the design of a new approach to improve the ventilation system of a real-life deep underground coal mine with multiseam workings. For this, the ventilation problem of one deep underground coal mine 6&7 pits Bhutgoria Amalgamated Colliery of Tata Steel Ltd. with multiseam workings has been studied in detail to determine an appropriate solution. A ventilation survey of the mine and computer simulation of the ventilation network has been carried out to reach a practical solution. Ventilation survey results have been analysed to develop a representative ventilation network of the mine for both qualitative and quantitative analysis. Further, computer simulation of the ventilation network of the mine has been performed to virtually verify the application of a highcapacity booster fan in the present ventilation circuit without disturbing the vulnerable areas. Field validation is also carried out after the implementation of the solution in the mine to determine its efficacy. Thus, the findings of this paper can be directly applied for the installation of booster fans to achieve the required air quantity in deep underground coal mines with multiseam workings having spontaneous combustion liabilities of upper seam goaved out areas.

Jun 2, 2022

By Qingwen Shi, Brijes Mishra

Laminated rock can delaminate and fail under certain stress states. Delamination-caused roof fall and cutter roof failure is a common failure mechanism in roadways in Pittsburgh coal seam due to the existence of laminated shale roof. Two-dimensional numerical models were developed at laboratory scale based on the bonded particle method in order to simulate the delamination with particle flow code. In these models, an assembly of bonded particles and parallel weak planes represents the laminated rock. This model calibrated the micro-parameters of the bonded particlematerial and weak planes with laboratory data. The mechanism of fracturing and delamination in a laminated specimen was investigated using unconfined and confined compression test and unsupported roof compression test. The numerical results show that, under a constant horizontal stress, delamination occurswhen the stress is much lower than its compressive strength. The confined compressive test indicates that delamination is restrained by applying confining stress since delamination-caused failure does not occur during any stage of the confined compressive test. Unsupported roof compression tests showed propagation of cutter roof failure with initiation of cracks and delamination at the intersections of the roof and ribs. An outer failed zone and inner failed zone form separately. The separated zones connect and form an opening in the roof. The presented numerical results provide additional insight into process of delamination.

Sep 14, 2020

By M. L. W. Tuttle, B. R. Berger

Our study focuses on the geology, hydrology, and geochemistry of a variety of molybdenum (Mo) porphyry systems. The systems are either high fluorine, granite, Climax-type, systems (e.g. Mount Emmons/Redwell Mo deposit, Colorado and Questa Mo deposit, New Mexico) or low fluorine granodiorite systems (e.g. Buckingham Stockwork Mo deposit, Battle Mountain, Nevada and Cannivan Gulch Mo deposit, Montana). The water quality of streams, natural springs, mine discharge, and ground water from drill holes were assessed in the region of these deposits. The ultimate goal of our study is to understand the environ-mental behavior of these Mo porphyry systems in the context of geologic setting, hydrologic regime, and climate.

Jan 1, 2004

By James Corcoran, Richard McLane, Joseph DeMello, Eric Carlson, Hans van de Vrugt

The Los Angeles County Transportation Authority’s Purple Line Extension Phase 1 is a $3.12 billion (USD) design-build, underground heavy rail project, connecting an existing station at Wilshire Boulevard and Western Avenue and extending west 3.92 miles under Wilshire Boulevard and terminating approximately 550 feet west of Wilshire/La Cienega Station. The project alignment runs through the heart of the world famous La Brea Tar Pits and one of the world’s largest urban oil elds. This paper presents a case history of the planning, design, and construction efforts to achieve successful construction of the bored tunnels through Reach 3 of the alignment. Further, this paper outlines the proactive partnership between the owner, Los Angeles County Metro (Metro), the Design Builder, Skanska-Traylor-Shea oint enture (STS), and Southwest Geophysics who provided the geophysical services. Specically, the project included background review of historic site data (e.g., oil eld maps, building foundation plans, historic aerial photographs, etc.), geophysical demonstration testing to ascertain the capability of borehole magnetics to detect oil wells, directional drilling of thousands of feet of horizontal and vertical boreholes, collection of high resolution magnetic gradiometer data along vertically and horizontally cased boreholes as well as the collection of surface magnetometer data, discovery (“ground truthing”) of detected geophysical anomalies, and abatement of potential obstructions within the tunnel alignment.

Jun 23, 2024

By Lida Sun, Na Wu, Mengyang Huang, Xingxiang Fan, Yan Jiang, Shasha He, Kunbin Yang, Yang Cao

The separation of lead (Pb) and mercury (Hg) from copper (Cu) smelting acid sludge using the carbonization and acidleaching total hydrometallurgical process was investigated. The effects of the excess coefficient of sodium carbonate, excess coefficient of nitric acid, conversion time, conversion temperature, dissolution time, and dissolution temperature on the separation efficiency of Pb and Hg were studied. The test results indicated that when the dosage of sodium carbonate was 2.0 times the stoichiometric ratio, the conversion time was 1.5 h, the conversion temperature was 75 ℃, and the amount of nitric acid was 1.8 times the stoichiometric ratio. Additionally, the dissolution time was 1.0 h, the dissolution temperature was 60 ℃, the ratio of liquid–solid was 5:1, and the separation efficiency of Pb and Hg was 98.72%. This study demonstrated the advantages of a short, simple, and environmentally friendly process for separating Pb and Hg from Cu smelting acid sludge, providing complete separation and introducing a new technology.

May 30, 2024

By Robert W. Bruhn

Ground movements associated with high extraction underground coal mining, such as pillar retreat and longwall, are sometimes large enough to disrupt the ground water regime as well as damage buildings and other surface structures. A U.S. Department of Energy/Bureau of Mines- sponsored subsidence study currently underway at Kitt Energy Corporation's Kitt No. 1 Mine near Philippi (Barbour County), West Virginia has provided an opportunity to monitor the ground water response above a mine panel during both developmental and pillar retreat mining. The initial findings concerning ground water effects presented in this paper indicate that total extraction mining produced significant water level declines in deep-lying strata but had little effect on water bevels at shallower depths.

Jan 1, 1985

By Fred W. Brackebush

In underground stopes that require more than minimal support, backfill is almost universally used. The term cut and fill stopingis used in a broad sense in this section, which describes underground mining methods requiring support. Support in stopes can be classified as local or short-term and general or long-term. Local support for the back of a stope, for example, can be accomplished with rock bolts or timber stulls. General support for the walls of the stope is provided by backfill. Local support provides a safe working place for the stope miners. General support, provided by backfill, preserves the access way to the stope and prevents large scale dilution of ore. Supported methods are a set of cut and fill stoping methods using backfill for general support and various local support methods. his section is subdivided into three chapters: 19.1 Cut and Fill Mining 19.2 Excavation Techniques 19.3 Backfilling Methods

Jan 1, 2008

By Carrie Pourvahidi

The California High Speed Rail Authority (Authority) was created by the State of California through legislation in 1996. The purpose of the Authority is to plan, construct, finance and operate a statewide intercity high speed passenger rail system. In 2004 the Authority prepared a programmatic level environmental document in compliance with the California Environmental Quality and National Environmental Protection Acts (CEQA and NEPA).The Authority and Federal Railroad Administration (FRA) were the lead agencies overseeing the development of the environmental documentation. The resulting document includes two volumes and 64 supplemental technical reports analyzing the transportation needs for California and the selection of an approach to meeting the project transportation needs. The Programmatic Environmental Impact Report and Environmental Impact Statement (EIR/EIS) identified High Speed Rail as the most environ-mentally protective, sustainable and economical approach to meeting the state?s projected transportation needs.

Jan 1, 2008

By Yuchen Wu, Jing Mei, GUOZHONG LIU, KE GAO, Songjie Tian, Jianwei Cheng, Yu Wang, Yuhang Wu, Hui Wang

The stability and integrity of protective coal pillars between the longwall working face and development roadways are greatly affected by the mining activities such as the development face advancing or retreat mining. Due to underground strata pressure, the coal pillar cracks could be further developed and then the air leakage passages (mainly cracks) could be produced greatly. The air circulation caused by the atmospheric pressure difference between the two sides of the coal pillar may also provide suitable conditions for the possible spontaneous combustion of the residual coal in the mine gob. In this paper, a typical the protective coal pillar in a Chinese coal mine is studied. The deformation and stress of coal pillars during the mining process of longwall working face are simulated by using FLAC3D. The displacement and strain of coal pillars are analyzed. Two indexes, the linear fracture rate (LFR) and area fracture rate (AFR), are introduced to characterize the development of internal cracks’ development within coal pillars. By using field measurement, the air leakage intensity distribution due to coal pillar cracks is obtained; the equation of air leakage resistance of coal pillar under the influence of mining is derived. Then, the possible location of large air leakage of coal pillar is determined, which can be used as guidelines to study the possibilities of coal spontaneous combustions happening in pillar or mine gob. The research results help to control such potential hazards in advance.

Jun 16, 2022

By Chunhui Zhang, Enton Bedini, Jiang Chen, Fengchao Yang, Hang Dong, Xiaoyan Chen

The alteration formed by the reaction of ore-bearing fluid and wall rock is often used as an important prospecting indicator, resulting in the dilution or enrichment of metals or related trace elements. A variety of rock-forming and metallogenic elements have been analyzed in regional stream sediments so that the relationship between the ore-bearing altered rock and the change in the geochemical elemental content can be obtained. Therefore, by using appropriate models, such as matched filtering, the abundance of the distribution of wall rock alteration, similar to the discovered deposits, can be modeled by using the distribution of geochemical elements in the region, and the areas with high distribution abundances are usually favorable prospecting targets. The alteration types related to gold mineralization in the Baiyun gold deposit are potassium feldspar alteration, silicification, pyritization, sericitization, and chloritization. In this paper, the geochemical data of the Qingchengzi ore field (1:200,000 and 1:50,000) have been used to form geochemical images through rasterization. In the three sections of the Baiyun gold deposit, binary-coded curves have been formed, revealing the differences in geochemical elements in stream sediments between altered rocks and the rocks surrounding the Baiyun gold mine. Among them, Au, W, and Mo are enriched elements, while Sn, Zn, and Hg are depleted elements. Several gold deposits are found in the predicted altered rock area by using the matched filtering method during fieldwork, which shows the effectiveness of the method.

Dec 30, 2023

By W. Clark Ashby

Productivity is a fascinating concept. Like motherhood or apple pie, we know it as a good thing. Just what it means is not so clear. To a coal miner we assume it means tons of coal hauled from the mine. To the company president it means profit after capital, labor, and other costs have also been reckoned. To the government economist it means output in a balance of payments. What does it mean to the biologist, and can reclamation really be productive? In this paper we discuss productivity from a biological viewpoint, give some yield data for various types of reclamation plantings, and discuss how our demand for or acceptance of differing kinds of productivity is tied up in bigger questions of land use, environmental stability, and resource allocation.

Jan 1, 1981

By C. Iglesias

Innovation in the tilemaking ceramic industry is stressing properties like powder flowability, ability to toughen green tiles, so turning technological requirements of ball clays ever stricter in terms of plasticity, dispersion in water, rheological behavior, workability in the green state, refractoriness and firing colour. Technological performance of ball clays was improved by taking as benchmark the highest quality raw materials on the market. The mineralogy, plasticity, methylene blue index and ceramic response of the Patagonian ball clays are analogous to those of European clays, but improvement is needed to approach the highest quality materials. On this basis, the Frente A, Super, Puma, and Lote 8 deposits were selected and their characteristics enhanced by additions of highly plastic and white-firing corrective clays targeted on the benchmark. Porcelain stoneware formulations, containing improved ball clay mixes, were experimented at both laboratory and industrial scale. The improved ball clays behave like the best raw materials currently used, although modest changes occur in the mechanical properties, water absorption and whiteness of the fired products.

Jan 1, 2010

By Gordon T. Clark, James R. Struthers, Celal Kirandag

INTRODUCTION Project Background The Washington State Department of Transportation (WSDOT) hired the Seattle office of Parsons Brinckerhoff to lead a team of consultants to produce an Environ-mental Impact Study and perform conceptual and preliminary engineering. The pur-pose of the Alaskan Way Viaduct and Seawall Replacement project is to replace the existing earthquake damaged and aging viaduct and sea wall, adjacent the downtown waterfront of Elliott Bay, with structures that have improved earthquake resistance and that maintain or improve mobility and accessibility for people and goods along the existing corridor. With an estimated replacement cost over $4 Billion and construction duration exceeding 8 years, it is one of the largest transportation design projects on the West Coast of the United States today. Seattle, Washington is a city of over 2 mil-lion people in the Northwest corner of the United States. Ever since the Klondike Gold Rush in 1897, Seattle has been considered a departure point to Alaska. Because of this, the street along the waterfront was named the Alaskan Way in 1930. Alaskan Way Viaduct and Seawall The Alaskan Way Viaduct (AWV) carries State Route 99 along the shoreline of Elliott Bay through downtown Seattle and is a vital part of Seattle’s highway system. The viaduct carries approximately 110,000 vehicles per day or 25% of all north-south traffic through Seattle (Figure 1). It is 3.4 km (2.1 mile) long with 3 lanes in each direction and was constructed of cast-in-place reinforced concrete between 1952 and 1956. The wear and tear of daily traffic, salty marine air, and several earthquakes have taken their toll on the facility. Studies in the mid-1990s provided early evidence that the viaduct was nearing the end of its useful life. The viaduct’s increasing age and vulnerability was apparent by crumbling and cracking concrete, exposed rebar, weakening column connections and deteriorating railings. In early 2001, a team of structural design and seismic experts began work to determine whether it was feasible and cost-effective to strengthen the viaduct by retro-fitting it. In the midst of this investigation, a 6.8 magnitude earthquake shook the Puget Sound region (the Nisqually Earthquake, located 56 km (35 miles) from Seattle and deep below the surface) caused moderate damage to the reinforced concrete structure. WSDOT closed the viaduct for inspection and repairs intermittently for several days over a period of several months.

Jan 1, 2007

By Jiayao Wang, Jian Chen, Leiting Shen, Hongyang Wang, Zeping Cao, Ziru Wang

Large amounts of by-products, including coal gangue, circulating fluidized bed (CFB) slag, and coal fly ash (CFA), are generated during mining, washing and burning of high alumina coal (HAC). The stockpile of these by-products of HAC will cause the pollution of air, water and soil. Meanwhile, the unbalanced regional distribution of bauxite and alumina production has been a critical challenge for the sustainability of world alumina refineries, especially for China. Therefore, economical extraction of alumina from by-products of HAC not only resolves the environmental pollution problems caused by stockpile but also decreases the dependence degree of import bauxite in China. Considering the fact that powder alumina can only be produced by alkali methods, the alkali extraction of alumina from by-products of HAC is summarized in this paper. Based on the formation process of by-products of HAC, the principle, research status, and problem of existing methods were analyzed and discussed, as well as the forecast of research trend. The analyses indicate that simplex recovery of alumina from byproducts of HAC generates large amounts of leaching residue (red mud) with difficulty for disposing, while comprehensive extraction of alumina and silica meets the research trend for clean and high-value utilization.

Aug 25, 2023

By Jogeshwara Sahu, Sapan Kumar Kandi, SANDEEP KUMAR JENA, Sachida Nanda Sahu, Sarada Prasad Das

The present article reports the recovery of potassium from mica scrap using carbide lime waste and NaCl. The acid leaching of mica [4 M H2SO4 at 90 °C] can recover a maximum of 25% potassium. However, in the chlorination roasting (with CLW and NaCl) water leaching process, it was possible to recover potassium to the tune of 94% [900 °C, 50 min roasting; mica:CLW:NaCl 1:0.75:1]. The formation of water-soluble phase like sylvite (KCl) and water-insoluble phases like anorthite ( CaAl2Si2O8) and nepheline ( NaAlSiO4) confirms the complete breakdown of the mica crystal structure. The extraction mechanism proceeds with the formation of a transition state followed by the release of potassium as KCl. The characterisation studies using ICP-OES, XRD, FTIR and FESEM support the proposed extraction mechanism. The salt produced by the evaporation of roast-leached liquor confirms the presence of sylvite and halite only, which can be separated to get the fertiliser grade KCl.

Sep 29, 2021