Search Documents

By V. T. McLemore

New Mexico Bureau of Geology and Mineral Resources (NMBGMR) has been collecting data on uranium mining districts, mines and mills since it was created in 1927 and has converted years of historical data into a relational database that can be imported in ArcMap. The database includes information on mining districts, mines, mills and geochemistry, as well as photographs and bibliographic resources. The available data includes location, production, reserves, geologic, geochemical, resource potential and other data. The National Uranium Resource Evaluation (NURE) stream-sediment data provides geochemical analyses for >27,000 samples collected in New Mexico during the 1970s. The NURE hydrogeochemical data provides analyses of water samples. ArcMap includes the location of individual ore bodies as polygons and incorporates the mines and NURE data as individual site locations. The purposes of these databases are to provide computerized data that will aid in identifying and evaluating resource potential, resource development and management, production and possible environmental concerns, such as physical hazards (i.e., hazardous mine openings), indoor radon, regional exposure to radiation from the mines, background geochemical data and point sources of possible pollution in areas of known mineral deposits.

Jan 1, 2010

By Amir Karami, Scott Munro

This paper focuses on remediation of a 3.6 km long water conveyance tunnel that suffered two large falls of ground (FoGs), one of which subsequently progressed to the ground surface, resulting in full collapse of the tunnel. The tunnel is part of a network of water conveyance tunnels and open channels that direct water into two turbines located in an underground powerhouse, originally constructed in the 1970s. At the time of construction, the tunnel was partially supported with shotcrete or rock bolts, with no further ground support added since construction. Two sonar surveys in 019 and 01 identied two adacent large FoGs in the tunnel, approimately 1.2 km from the tunnel outlet. Historical geological and geotechnical information indicated that the FoGs occurred within a 60 m wide fault zone. Remediation plans were developed, which included stabilization of the outlet channel, the portal, the tunnel leading up to the FoG areas (1.2 km length) and the FoG areas. Several remediation options were considered to restore the tunnel, including construction of a diversion tunnel to bypass the FoGs or remediation of the FoG areas with steel ribs and backlling the void above the FoGs to surface.

Jun 23, 2024

By R. J. Lee

Asbestos analysis is conceptually simple. The objective, in most environmental analyses, is to determine the number of asbestos fibers per unit area or volume in a sample. The sample may be a consumer product, an ambient air sample, or a water sample. This determination is complicated by several factors including sample collection and preparation, counting techniques, and the operational definition of asbestos in use. Three different definitions have been used in the study of environmental samples; these are summarized in Table 1. [ ]

Jan 1, 1979

By Daniel T. Hegyan

The employment of continuous rotary vacuum disc filters to filter refuse from the fine coal washing circuits has been increasing as it has become more important to close the water circuits and eliminate sludge holding ponds. This paper will discuss our past experience filtering refuse, effects of solids concentration in the filter feed, use of polymer flocculation aids, effect of flocculation devices, and effects of particle size and ash content on the filtration rate. Detailed tests were performed on existing installations utilizing coal refuse filters to determine optimum flocculant dosage, solids concentration, and disc rotation speed to form a dischargeable cake. Information was also obtained showing effect of flocculant addition on the moisture of the filter cake. Our test work has shown that the continuous filtration dry cake rates for fine coal refuse correlates very well with the data developed and presented by Silverblatt and Dahlstrom1 except that the curves have moved up the scale by use of polymer flocculant additions. These polymers were not available at that writing. Finally, our tests also confirmed the general premise stated by S. K. Mishra2 that controlled additions of polymer flocculants will reduce filter refuse cake moistures somewhat.

Jan 1, 1974

By G. R. Harrod

Effective mine operation demands that the right people have the right information at the right time. Caterpillar's Mining and Earthmoving Technology System (METS) meets this demand by providing "real-time" information transfer between the mine offices and machines equipped with the Caterpillar Computer Aided Earthmoving System (CAES). Transfers of mine plans from the mine planning software to CAES-equipped machines give operators access to current mine plans within minutes of their creation. Additionally, office personnel have access to a current digital terrain model (DTM) of the mine site as it is updated in "real-time" by CAES-equipped machines. METS provides mine personnel in operations, planning, and management the information they need when they need it.

Jan 1, 1998

By S. W. Arambur

INTRODUCTION "Mujeres Roca" is a program developed by OMA in association with the Chamber of Commerce Canada Peru inspired in “Women who Rock”, a Canadian initiative to promote a greater participation of women in the mining industry. The program includes a coaching workshop called “Kallpa Warmi”, that means “Woman Strength”, to reinforce basic skills and values and 8 mentoring sessions with top executives of the mining industry who share their experiences and knowledge with a group of 10 selected young professional women from around the country. HISTORY OMA is a nonprofit association founded in 2014 dedicated to contributing to the education of low-income university students with high academic performance in careers related to mining and earth sciences. Our mission is to empower the future professionals by strengthening their soft skills and enhancing their capacity to become leaders and agents of change in their own regions. The Chamber of Commerce Canada Peru has a long-standing commitment to gender equality and promotes women participation in male dominated industries. As it is well known, the mining sector is and has always been key to Peru’s economy, representing about 10% of the country’s GDP. Thus, mining can contribute significantly to our economic development and we believe that women can make a positive difference. A study prepared by PwC and "Women in Mining” provided indicators on the advantages that mining companies have when including women in their executive’s positions. These indicators sustain that when a mining company includes women in its management staff, its net profit increases by 6%. This information clearly shows that women participation is not only a matter of human rights and gender equality, but of productivity and profitability. Nevertheless, the mining sector has the fewer number of women on boards of any industry group in the world. Having this in mind, OMA decided to expand its activities and create together with the Chamber of Commerce Canada Peru, the program “Mujeres Roca”, in order to inspire and attract young women to the mining sector, a traditionally masculine industry. The program also aims to encourage mining companies to more actively recruit and keep women in their boards. The program was launched in 2016 within the framework of EXPOMINA PERU, the largest international mining exhibition that take place in Lima every two years.

Jan 1, 2019

By ?. ?ivkovic

The silicate slag and copper matte that are the byproducts of smelting copper in a reverberatory furnace contain SiO2, FeO, Fe3O4, CaO and Al2O3, and Cu, Fe and S, respectively. These components influence the oxide (Cuox), sulfide (Cusul) and total (Cutotal) copper content lost in the waste slag. This paper uses multiple linear regression analysis (MLRA) to determine the degree of influence. The results of calculations obtained using MLRA were compared to actual measured results and found to have a large degree of correspondence, with the coefficient of determination R2 = 0.975. These results indicate that slag composition and copper content in the matte influence the copper losses in the waste slag with a probability of above 97%. It was determined that, of the total copper content of the slag, 74% is in sulfide and 26% in oxide form, and that this ratio is not dependent on the slag or matte composition.

Jan 1, 2010

By R. L. Amelunxen

P. T. Freeport Indonesia (PI) in conjunction with Crescent Technology Inc. has developed a method to predict the metallurgical performance of ores blends based on the behavior of their component ores. The question addressed in this paper is whether ores treated individually could be extrapolated to predict the behavior of a blend of ores. The work further investigates the use of modal analysis to establish individual mineral flotation kinetics in each of the ore zones. This information would lead to the prediction of grade-recovery curves of ores made up of those minerals. Nine samples of ore, representing various zones of FI's Grasberg ore deposit were tested metallurgically and examined microscopically. The same testwork was performed on blends depicting the 1994 mill quarterly feed. Flotation kinetics of the individual ores were then "mathematically" blended and compared to the results obtained from the quarterlies. The calculated kinetics of the actual blends of ore received by the mill were fed to the simulation program and compared to the actual mill performance.

Jan 1, 1995

By Thomas P. Meloy

Floating "fines" differs from floating "sands" because the fines have a much larger surface area compared to their mass. The forces that arise from this large specific surface the key to understanding the behavior and treatment of fine particles. Though the nature of these forces is not thoroughly understood, enough work has been done to give a qualitative picture of what is happening in a flotation cell. It is the purpose of this chapter to re-examine some of the more, recent theoretical work and-to indicate its importance.

Jan 1, 1962

By M. K. Rizkalla

This paper discusses the time-dependent behaviour of rock when it involves the presence of several layers of rock strata in the vicinity of mine openings, mining in sequences and the placement of backfill. The paper describes numerical techniques which proved useful when such situations are encountered in practice. The model is elastoviscoplastic. At given time stations, short term loading or changes can be made to the creep behavior of the rock. The modelling technique is first described and is followed by simulations of stresses and displacements in a potash mine with the primary objective to demonstrate the effect of such aspects as mining and fill sequences in 3-D. This involves cutting finite elements representing the strip of the mining face and simultaneously filling those elements representing the newly placed fill. The stiffness of the fill varies with the degree of compaction at each point. In this way, the effect of the time of fill placement, the gap between the top of the fill and the back as well as the degree of compaction are simulated. The second example is a 2-D problem simulating the long term effect of backfill, as a material compacting with time, on the settlement of the layers above it as well as the closure of the room.

Jan 1, 1996

By R. Venugopal, V. K. Saxena, Veerendra Singh

"Ore morphology plays a vital role during the milling and liberation of minerals. This study was carried out to understand the role of mineral crystallography and mineral interfaces on the milling and liberation processes. Data related to mineral crystallography, Vickers Hardness Number and beneficiation processes were collected from literature, and detailed statistical analysis was conducted to relate these parameters. Review of the crystallographic information of minerals present in ores indicates that molecular weight and cell parameters significantly affect milling and liberation characteristics. Mineral interfaces were classified into the three categories of coherent crystals, semi-coherent and incoherent crystals, and breakage behaviors were studied. The studied cases revealed that these material interfaces control the micropore properties that play a vital role in the initiation of intergranular and intercrystalline fractures which occur in siliceous manganese ores and dolomite as a result of thermal treatment. In contrast, banded hematite jasper and coal exhibited a much more complex fracture pattern due to their coherent interfaces and finer physical associations. This study explains the effect of the various types of interfaces on milling, and the approach can be helpful in developing a methodology to enhance mineral liberation with minimum energy consumption.IntroductionComminution is a vital unit operation in the mineralprocessing, cement-making, power-generation and pharmaceutical industries. Its importance in mineral beneficiation operations is increasing every year as a result of the growing need to exploit lower-grade ore bodies and process reject materials (Blazy et al., 1994; DOE, 2005). Low-grade ores require significant energy during grinding to liberate the valuable minerals, which are further separated from the gangues by various beneficiation methods. Various attempts have been made to enhance mineral liberation during grinding to minimize energy consumption. Most of these studies focused on the analyses of the compression mechanism, chemical additives, thermal treatment, microwave treatment and electric disintegration (Klimpel and Austin, 1982; Norgate and Weller, 1994; Bearman et al., 1997; Kumar et al., 2010; Wang et al., 2011; Singh et al., 2012). However, many of these efforts had limited success, and there is a need to see the problem from a fresh perspective."

Jan 1, 2015

By Éder Domingos Oliveira, Carlos Antonio Morais, Ruberlan Gomes Silva

The objective of this study is to assess the impact of different reagents, such as limestone, lime, magnesium oxide, and sodium hydroxide, in experiments carried out in the single purification step and in two consecutive purification steps by raising the pH of a rare earth sulfuric liquor with the aim to remove or reduce the impurity concentrations in the rare earth sulfuric liquor. The choice for the best purification condition was made based on the minimum loss of rare earth elements (REEs), reagent consumption, and residue generation. The exploratory experiments show that it takes place in the two consecutive purification steps, the first one consists in dosing the limestone pulp until it reaches a pH of 3.5 followed by an addition of a lime pulp reaching a pH of 5.0. Under this condition, the results were a total removal of Fe3+, PO4 3− , and Th4+ ions and a reduction of 99%, 87%, and 37% w/w in the Al3+, UO2 2+, and SO4 2− concentrations, respectively, in the purified rare earth liquor. Furthermore, the lowest REE losses (8.3% w/w) and reagent consumption (4.3 kg/m3 ) and also a low residue generation (7.5 kg/m3 ) were observed in this condition. Despite reaching similar results regarding impurity removal, the experiments done with the addition of limestone, lime, magnesium oxide pulps, and sodium hydroxide solution in the single purification step, where the pH was raised to 5.0, presented higher REE losses (64.9%, 42.5%, 44.8%, and 60.9% w/w, respectively) and a higher residue generation (43.2, 25.1, 11.1, and 13.6 kg/m3 , respectively). This occurred due to the co-precipitation of salts containing rare earth elements in their composition. The experiments conducted with limestone, lime, and MgO resulted in a higher consumption of reagents, while the same result was observed when NaOH was used (4.3 kg/m3 ). In the experiments carried out with the addition of magnesium oxide and sodium hydroxide, the respective purified rare earth liquors presented a high concentration of magnesium, sulfate, or sodium, which could impact the quality of the marketable rare earth salts, whereas the salts obtained under the best condition observed in this study seem to be amenable for use as raw material in an attempt to obtain rare earth products with an acceptable chemical quality.

The dissolution kinetics of gold in iodide solutions with oxygen in an autoclave was investigated. The leaching process was described by a gas-liquid-solid heterogeneous reaction. The effect of stirring speed, temperature, partial pressure of oxygen, and concentration of lixiviants on the overall leaching rate was investigated. It was found that the dissolution of gold was limited by a heterogeneous chemical reaction. The apparent activation energy was measured to be 34.7-54.3 kJ/mol under the conditions studied. Experimental findings were in good agreement with the kinetic model proposed.

Jan 1, 1996

By Elgin D. Bell

Within the next, year or two, Western Canada should overtake Mexico and France. to become the worlds second largest producer of elemental sulphur, surpassed only by the United States, By 1965, it should produce about 25% of the world's total elemental production and, about 10% of sulphur produced in all forms. In 1952 Alberta had but one small sulphur recovery plant. By 1962, it had fifteen plants with a total designed capacity of almost 6,000 long tons of sulphur per day and actual production of almost one million long tons per year. This decade of dynamic growth was the result of Alberta's rapidly developing natural gas industry. More particularly it was the result of approval in 1960 to export natural gas in large volumes into the United States. Prior approval to export gas from Alberta to eastern Canada and relatively modest volumes to the U. S. had resulted in the construction of several plants but none were of the scale required to serve the U. S. market.

Jan 1, 1963

By Yukika Miyashita, Takahiro Inoue, Kenji Namikawa, Masashi Matsumoto, Junichi Koseki, Yoshihiro Terashima

"In order to construct an underground two-layer expressway branch junction structure with a height of 14.7 m and a width of 22.3 m, two shield tunnels in each layer were combined by using a non-cut-and-cover enlargement method in sedimentary soft rock. Before and during the construction work, preliminary analysis, in-situ investigations and laboratory tests were conducted to ensure the construction safety and to evaluate the deformation characteristics of sedimentary soft rock. The construction project was safely executed without any water leakage or collapse of tunnel working face. The predicted results from preliminary analysis were almost similar to the measured values. From the detailed investigation of measured results, it was confirmed that the deformation characteristic of the sedimentary soft rock was observed to a small extent as the ground deformation derived from construction work. INTRODUCTION In recent years, some newly constructed urban expressways in Japan are being planned as underground structures due to the consideration of roadside environment. The construction of such underground expressways is frequently conducted using a shield tunneling, a typical one of non-cut-and-cover methods, to prevent any adverse effect to traffic in arterial roads, operation of nearby commercial establishments, and daily lives of local residents during construction work. For underground urban expressway, the connections with existing road network on ground surface or on elevated sections are indispensable, which require the construction of an underground branch junction with large cross-section. This raises a technical difficulty regardless of the open-cut or non-open-cut construction method."

Jan 1, 2016

By Lei Pan, Venkata Atluri, Xuming Wang, Yuesheng Gao, Jan D. Miller

The wetting characteristics and water film stability at the talc surface have been studied, particularly the effect of polysaccharides such as guar gum, starch, and dextrin. Talc is a gangue mineral in the flotation of base metal sulfide ores, precious metal sulfide ores, and platinum group metal (PGM) sulfide ores. Talc surfaces were investigated using surface analysis techniques including atomic force microscopy, high-speed video bubble attachment measurements, and wetting film stability measurements using a synchronized tri-wavelength reflection interferometry microscope (STRIM). In the presence of polysaccharides, there is a significant increase in bubble attachment time at the talc surface, but only a slight change in contact angle, which suggests that polysaccharide depression of talc is due primarily to the slow rate of bubble attachment and not due to a change in contact angle. The critical rupture thickness (hc) for a hydrophobic talc surface was found to be 56 nm, while the hydrophilic phlogopite surface of similar structure has an equilibrium film thickness (he) of 25 nm. At low polysaccharide concentrations, the wetting films formed on the talc surfaces were unstable, but at high concentrations the wetting films became stable with similar thickness values as the critical rupture thickness, and bubble attachment did not occur. However, it was found that the critical and equilibrium film thickness values do not change significantly with the polysaccharide type or concentration. The results from this research help us understand further details of film rupture and displacement during bubble attachment.

By Thomas M. Lynberg

WIDCO is a surface coal mine located near Centralia, Washington. The WIDCO preparation plant processes over 7 million tons of run- of-mine coal each year with a product yield averaging 72%. In the jig type preparation plant the fine refuse amounts to approximately 130 dry tons per hour of 28mesh by 0. This fine refuse material is thickened in a 160ft. diameter static thickener with the use of lime as a coagulant and organic polymer as a flocculant. Once thickened the fine refuse, which is predominately bentonitic clays, has been dewatered and disposed of using several different methods. These methods will be discussed and include vacuum disc filters, ponds, solid bowl centrifuges, belt filter presses and experiments with electrokinetic dewatering.

Jan 1, 1981

By Paul R. Weber

Open-pit mines are constructed in materials characterized by the complete range of geologic materials from the most recent alluvial sediments to hard intact crystalline rock. The determination of stable slopes in recent alluvium is in the realm of soil mechanics, an established engineering discipline, well founded on theoretical development and years of substantiating experience. The analytical tools of the soils engineer are chiefly derived from continuum mechanics wherein load-deformation response is governed by mass properties of the substance. At the other end of the spectrum, slopes in hard unweathered rock can generally be analyzed in a straightforward manner by the methods of discontinuum mechanics wherein the properties and orientations of joints control the response of the material. This approach is exemplified by the classical work of Terzaghi (1962). In between these two extremes is a gray area of material types which are composed of stiff soil and incompetent rock. This area is of importance to the mining engineer, since a large portion of open-pit mines is excavated wholly or in part into incompetent rock. This paper describes an approach to pit slope design in incompetent rock in which the material behaves essentially as a continuum. A wide range of geologic materials from stiff soil to poorly indurated sandstone and shale to crushed or weathered crystalline rock appear to fit in this category. These materials all possess certain mechanical properties which must be accounted for in a realistic assessment of slope stability. These properties include nonlinearity, s tress -dependency, and inelasticity. Further considerations involve residual stresses and time-dependent seepage pressures where groundwa.ter is present.

Jan 1, 1971

"A long-term mine production schedule optimization based on stochastic integer programming is presented that manages the risk due to geological variability and uncertainty while jointly considering mine profitability, truck fleet requirements and waste management. The evolution of the pit is controlled so that space within the mined-out pit is continuously provided to allow for tailings and waste rock to be replaced, thus minimizing the project’s environmental footprint. The method is applied at a taconite iron ore deposit and has a project net present value that is 16.9 percent higher than that of a conventional schedule and has a higher chance of meeting production forecasts. The stochastic schedule reduces equipment requirements by delaying waste mining and by mining selectively in order to meet plant ore feed requirements without stockpiling material, resulting in 23.7 and 26.2 percent lower mining capital and operating costs, respectively. IntroductionThe LabMag iron ore deposit is part of the Millennium Iron Range, a 210-km (130-mile) belt of taconite in northern Quebec and Labrador, Canada. LabMag has significant economic potential. It contains more than 3.3 Gt (3.6 billion st) of proven reserves at an average total iron content of 29.8 percent and is very low in impurities. However, on a project basis of 23 Mt/a (25 million stpy) of product, the required capital expenditure is estimated at more than $5 billion (SNC-Lavalin, 2014), which necessitates careful evaluation of all sources of risk. Resource estimation is one of the main sources of risk in a mining project as knowledge of the orebody is primarily based on drilling, which is often sparse because it is expensive. If the expected ore tonnages and qualities are not obtained when mining, the project cash flows are directly affected. The expected quantities and qualities of ore and waste are defined by the mine production schedule, which specifies the sequence of extraction and is dependent on the resource estimation. The goal of mine production scheduling is thus to maximize the expected profit, while also meeting all production targets and constraints, by creating an extraction schedule that is robust in the face of geological risk and has the highest chance possible of actually being realized."

Jan 10, 2017

By Leonard Sugin

As we approach the end-of the 20th century we are made more aware of the tremendous role that energy plays both directly and indirectly in our varied way of life. The industralized nations of the world have already established industries and economies which are greatly dependent upon the availability of energy. The underdeveloped and developing nations of the world are slowly and surely moving to the same utlimate requirements. The world wide need for distribution of energy sources is continuing to grow. At the present time there is a great imbalance between the sources of energy and the consuming economies In order to bring about greater equality between supply and demand major efforts and large capital expenditures are constantly being made. Industralized areas are seeking their own independent sources of energy whereas those areas of the world which contain great reserves of energy are limiting its export as well as developing its own industralized capacity. Nevertheless, energy bearing materials are still transported great distances in order to satiate the appetites of power hungry economies.

Jan 1, 1975