Search Documents

By Christopher J. Bise

INTRODUCTION The transportation of men, supplies, and mined material from an underground operation is the connecting link between the mine plant and the surface plant. Unless the mine is accessed by a drift or adit, some form of hoisting system is necessary for slopes or shafts. This chapter will deal with the selection of wire ropes and hoists, two of the most important consider¬ations when designing a hoisting system for an under¬ground mine. WIRE ROPES General A wire rope is designed to transmit forces longitudi¬nally along its axis. Wire rope is used in a variety of mining applications because of its flexibility, high ten¬sile strength, and dependability. Shaft hoisting ropes and principal slope haulage ropes are usually custom-¬built; however, proper rope selection for slushers, car spotters, etc. should not be overlooked. Wire ropes for shafts and slopes, since they represent the life line for the mines, should be of the very highest quality improved plow steel. This quality is necessary to deal with the conditions of loading, winding, vibration, abrasion, and corrosion. Tables I and 2 display the specifications for the typical wire ropes used for mine haulage applications. The 6 x 19-class haulage rope is used for most hoisting where abrasion is not critical. On the other hand, where abrasion is critical, such as a slope application, 6 X 7-class haulage ropes are preferred. For other mining applications, manufactur¬ers' handbooks should be consulted. Selection The selection of a wire rope for a mining situation consists of simply applying appropriate safety factors to a calculated maximum rope pull and comparing the result to the listed breaking strength of the rope under consideration. Table 3 can be used for determin¬ing the minimum factors of safety for wire ropes. To determine the maximum rope pull, the following quantities must be known: the rope weight in pounds (x), the conveyance weight in pounds (y), and the weight in pounds of the load in the conveyance (z). These values are used to calculate the load due to gravity, the load due to conveyance friction, and the load due to rope friction. When these loads are added together, as shown in Eq. 1, the maximum (static) rope pull (RPS) can be derived:

Jan 1, 1986

By Jue Kou, Lei Yu, Bern Klein, Lusheng Zhou, Chunbao Sun, Genzhuang Li, Reem Roufail, Amit Kumar

Magnetic liners can improve the performance of ball mills by increasing grinding efficiency, extending service life, and reducing maintenance costs. Despite their importance, the fundamental understanding and the quantitative investigation on the effects of the magnetic liners has not been addressed in the literature. This paper addresses this gap by studying charge motion, and how the use of a magnetic liner affects the breakage mechanism of the mill, using discrete element method (DEM) modeling and the Hertz-Mindlin contact model with relative velocity dependent (RVD) rolling friction. Charge motion was modeled under different mill speeds. Compared to conventional steel and rubber liners, the charge motion in the magnetic liner mill was predominantly cascading. Quantitative analysis of the energy dissipation within the mill was conducted to investigate mill breakage. Regardless of speed, over 50% of the total energy dissipation in the magnetic liner mill was in the form of abrasion and attrition. The results highlighted the appeal of magnetic liners in secondary and regrinding application, where abrasion and attrition are considered more efficient in the fine material breakage, and where impact is ideally minimized to reduce mill wear. A number of experiments were conducted to assess the effect of different model parameters on the performance of the magnetic liner mill. The highest abrasion/attrition intensity was observed with high values of the model parameters namely the restitution coefficient, static friction coefficient, and rolling friction coefficient.

Jun 12, 2019

By Binbin He, Baiwei Lei, Rehamutula·Rouzi, Zheng Wang, Chao Li

Methane explosions are highly destructive and constitute a primary hazard affecting mine safety. Seals are commonly employed to obstruct the propagation of methane explosions within tunnels, with the aim of reducing the damage caused by methane explosions. In order to study the influence of the seals’ position on the parameters of methane explosion damage, this study takes the Lake Lynn Experimental Mine No. 501 in the United States as a background case. It investigates the methane/air explosion damage parameters at different positions of seals in a fully sized roadway using the GASFLOWMPI code. The coupling mechanism between methane explosion gas expansion and reflected waves is analyzed. Finally, the variation patterns of explosion damage parameters are analyzed based on explosion damage criteria. The results show that as the distance increases between the seal and the explosion source, the maximum overpressure and impulse at the seal decrease exponentially, and the decrease is more significant when the seal is closer to the explosion source. The maximum velocity and maximum dynamic pressure increase first and then decrease, reaching their maximum values at approximately 115 m. They are approximately 163.355 m/s and 30.485 kPa, respectively. According to the analysis of explosion damage criteria, it is found that overpressure damage is the main form of methane explosion damage. But the damage of impulse and dynamic pressure is not be ignored. The relative position between the seal and the gas expansion area significantly impacts the parameters of methane explosion damage due to the coupling effect of gas expansion and the overpressure reflected wave from the seal. When the seal is set in the gas expansion zone, the further the seal is from the explosion source, the greater the dynamic pressure damage and the more minor the overpressure and impulse damage. The closer to the explosion source, the more significant overpressure and impulse damage changes. When the seal is set outside the gas expansion zone, the further the seal is from the explosion source, the more minor the overpressure and impulse damage to the seal, and the dynamic pressure damage increases first and then decreases.

Apr 24, 2024

By Gabriel K. Nzulu, Lars Hultman, Per Eklund, Martin Magnuson, Abu Yaya, Prosper M. Nude, Hans Högberg

Pyrite is the most common among the group of sulfide minerals in the Earth and abundant in most geological settings. This gangue mineral in association with garnet, hematite, magnetite, and other sulfide minerals acts as an indicator mineral in the Kubi concession of the Asante Gold corporation in Ghana. X-ray diffraction (XRD), air annealing in a furnace, energydispersive x-ray spectroscopy (EDX), and X-ray photoelectron spectroscopy (XPS) were applied to investigate the crystal structure, identify individual elements, permanence, transformation, and chemical/electronic properties of such pyrite. The study aims to identify individual elements and to gain an understanding of the surface reaction mechanisms, as well as the properties of precipitated pyrite particles observed during the hydrothermal formation of the ore deposit. XRD shows that pristine and annealed samples contain some hematite and quartz besides pyrite. Results from air annealing indicate that the relationship between pyrite and hematite-magnetite is controlled by temperature. EDX reveals that the sample has O and C as contaminants, while XPS in addition reveals Ba, Au, P, Al, and N. These elements are attributed to pyrite that bonds metallically or covalently to neighboring ligands/impurity minerals such as oxides, chalcogenide sulfides, as well as the gangue alteration minerals of magnetite and hematite in the pyrite sample. These findings suggest that during the hydrothermal flow regime, pyrite, pathfinder elements, and impurity minerals/metals were in contact with quartz minerals before undergoing hematite transformation, which thus becomes an indicator mineral in the Kubi gold concession.

Feb 27, 2024

By Debasis Deb

The first version of the longwall strata control and maintenance system (LSCMS) has been successfully developed by the Strata Control Re¬search Team at the University of Alabama. The system includes a software package designed to monitor shield leg pressure, interpret the data and predict the forthcoming roof loads and the existence of geological anomalies. It can also detect maintenance problems of the face equipment. The LSCMS was installed underground and connected to the surface terminals at Drummond's Shoal Creek Mine in Alabama. The system has proven to be a useful and practical system for improving safety and efficiency in coal-mining operation. The Shoal Creek Mine is a new, large coal mine operated by Drummond with two longwall panels. The Blue Creek seam is the primary source of coal production. It is located at a depth of 275 to 440 m (900 to 1,450 ft) below the surface with an approximate 2% southwest dip. Typical strata conditions are represented by two stratigraphic columns (Figs. la and b). A fireclay/dark shale parting (called Middleman) 0.2- 0.7-m- (1- to 2.5-ft-) thick exists between the Mary Lee and Blue Creek seams. Mining conditions vary from area to area. This mainly depends on the Blue Creek seam thickness that ranges from 0.9 to 2.9 m (3 to 9.5 ft). The thickness of the Mary Lee and the parting is relatively consistent with a to¬tal of 0.9 m (3 ft). They are mined when the Blue Creek seam becomes thinner. In most of the panels, the immediate roof is composed of sandy shale 1.5-

Jan 1, 1997

By M. K. McCarter

In 1963, a major expansion program at Kennecott's Bingham Canyon mine converted rail operation in the upper portion of the pit to truck haulage. Since that time truck-haulage capacity has increased to about 272 000 Mg (300,000 tons) per day. The majority of this production is waste material which is deposited in monolithic dumps located on the eastern slopes of the Oquirrh Mountains. The largest of these dumps, referred to as Copper Notch and Keystone, measures approximately 1830 m (6000 ft) in length, from 180 to 300 m (600 to 1000 ft) in height, and contains some 430 Tg (470 mil lion tons) of waste. The height, structure, rapid rate of growth, and anticipated leaching suggested the possibility of dump failure. In order to evaluate this possibility, an outside consulting firm was retained in 1966 to investigate the stability of the growing dumps. Their investigation indicated that, other than superficial movement, the waste dumps would be stable under static loading, and that soil distribution was not continuous enough to sustain massive foundation failure. Since this investigation, however, several failure processes have been observed. Crest settlement occurs frequently in response to compaction and over-steepening in the upper portion of the dump surface. Over-steepening results from accumulation of fines near the crest caused by natural segregation. Normally, coarse material, near the base of the dump, exhibits an angle of repose near 0.65 rad (37"). The fine material, however, stands as steep as 0.75 rad (40"). Periodic equilibrium adjustments cause stepwise settlement (Figure 1) of the dump surface and occasional sloughing of the protective berm. Routine surface preparation by dozers and graders and frequent inspections by supervisory personnel have proven adequate in preventing problems associated with this form of crest instability.

Jan 1, 1976

By Maurice Grieves

GC. Waterman Mr. Grieves' paper on "Shaft Sinking Today--A Boring Business Tomorrow" in the Dec. 1981 issue of MINING ENGINEERING is an excellent description of recent improvements in speed and costs of shaft sinking. However, shaft boring techniques are not a recent development. In 1935-36, the Idaho Maryland Co. (gold), Grass Valley, CA, bored the vertical 1.5-m-diam Idaho No. 2 ventilation and supply shaft to a depth of 346 m. The equipment was designed and perfected by Branner Newsome and was, I believe, described in "Transactions." Pickands Mather later bored a 1.8-m-diam shaft to a depth of about 305 m using Newsome's design. The Idaho No. 2 shaft cut through hard gabbro, diabase dikes, soft serpentine, very incompetent ankeritized serpentine and a strong fault zone. The completed shaft did not require timber support; the fault zone was cemented. Equipment consisted of a rotating 1.5-m or 3-m core barrel with a slotted bottom which cut a 76-mm kerf. The cutting agent was chilled steel shot introduced into the slot as needed. The driving mechanism and core barrel were lowered into the shaft, the former secured to the wall and the inshaft "engineer" operated the motors which controlled core barrel rpm and advance. After an advance of 1.5-3 m the equipment was lifted out of the shaft, a half(?) stick of powder cut off the drilled core, and it was hoisted to the surface with a cable attached to an eye bolt at the tope of the core. A "shift" consisted of three men: hoistman, equipment operator (down the shaft), and a surface laborer. Advance was variable as equipment and techniques were perfected. Near the end of the job advance was, as I remember, 1.5-3 m per shift. Costs were, as I recall, about $115/m. Up to 4 m cores were lifted out in one piece and swung to the dump by a stiff leg derrick. The Newsome equipment was relatively inexpensive to build and operate and his method should be (more than?) competetive with the methods described by Grieves. W.E. Hawes The author, in mentioning the South African developments of the cactus grab, ignores the parallel development of the Cryderman mucker in this hemisphere. Perhaps a slightly longer history of blind hold drilling would have been in order. Blind shaft boring got a major boost at the Nevada Test Site, as part of the nuclear weapons development, when it was essential to be able to quickly assess depth for weapons testing. One of the early civilian attempts to utilize this technology occurred when Kerr McGee drilled the shaft at the Section 19 Mine at Ambrosia Lake, NM. This twin masted drill rig belonged to a subsidiary of Kerr McGee, not Shaft Drillers. This was a difficult hole, due to bentonitic shales that decomposed. Later advances in drilling fluids eliminated this problem. The Conoco project referred to is not entirely correct, and needs minor amplification: The depth of the development (not pilot) shaft drilled was 684 m, at a diameter of 3.05 m, with a 2.16 m ID hydratatic casing being installed to a depth of 669 m. Conoco Inc., not Challenger, executed the drilling, however Conoco did use Challenger Drilling Company's Rig 14-S. Rig 14-S is unique in that it is specifically designed for shaft drilling, rather than being an oil field rig used for this service. All work was planned and directed by Conoco personnel. Deviation of the aforementioned shaft from vertical was 31 cm. Two smaller shafts (pilot shafts) were drilled with the same rig. These smaller ones were drilled 1.8 m in diameter, to depth of 665 m and cased with .91-m-diam casing, to depth of 650 m to be used as pilot holes for 5.5 m diameter shafts. The total elapsed time for all drilling, casing, cementing, and rig moves was 50 weeks. The constraints mentioned of vertical accuracy, torque, wall collapse, rig set up time, lining time etc., pumping out, etc., may not be as serious as the author implies. First, vertical accuracy: The record achieved by Conoco indicates that with reasonable care, good accuracy can be obtained, primarily by having a fair amount of weight in tension, rather than on the drill bit. Second, the amount of torque that can be applied to the drill stem has been greatly increased by the introduction of larger diameter drill stems, such as the new Hughes rig uses. Third, risk of collapse of shaft walls is minimal with the proper mud program. Basically, the walls are supported by the weight of the mud and it is not removed until some type of casing is installed and grouted in. Here in the real challenge of blind drilling shafts to devise a more economical method of lining bored shafts than using steel casing. The remaining issues were minor at Conoco, provided adequate planning and scheduling takes place. An excellent paper, "Shaft Drilling--Crownpoint Project" by Hassell H. Hunter, presented at the Fifth Uranium Symposium in Albuquerque in Sept. 1981 contains details of this project. A combination of blind boring, with enlargement by either mechanical means (boring machine, or tunneling type shield) or slabbing down, with muck removal through a larger bored shaft would seem to be the future trend in shaft development. The economics, especially for wet conditions, favor this concept over conventional sinking, as has been demonstrated at Kerr McGee --Churchrock, UNC--Churchrock and Conoco at Crownpoint.

Jan 3, 1983

By Yonghong Qin, Songbo Ma, Qi Zhang, Peng Gao, Jianwen Yu

Herein, the coal-based reduction was proposed to utilize the ferronickel slag of Jingchuan company. An excellent index with metallization rate of 99.22%, iron grade of 77.91%, and iron recovery of 92.79% was obtained at carbon addition coefficient 2.0, reduction temperature 1573 K, reduction time 60 min, the particle size of coal and ferronickel slag − 2.0 mm, and CaO content 15%. The 2FeO·SiO2 was reduced to Fe and SiO2 with the increase of temperature. The CaO could promote the reduction of iron oxide. Most of the sulfides (Fe, Cu, Co, and Ni) in the sulfonium were reduced to metal. The reduction degree increased with the reduction time and reduction temperature. The higher reduction temperature represented the higher peak value of reduction rate and the shorter time of reaching the peak value. The isothermal reduction process included three stages: early stage, middle stage, and late stage. The mechanism function were f(α) = 1/2(1 − α)3, f(α) = 3/2(1 − α)4/3[(1 − α)−1/3 − 1]− 1, and f(α) = 4(1 − α)[− ln(1 − α)]3/4, respectively. The activation energy of three stages was 183.498 kJ·mol−1, 420.077 kJ·mol−1, and 656.619 kJ·mol−1, respectively.

May 24, 2022

By Kaige Zheng, Hongwei Wang, Tong Wang, Yanjun Li, Yongping Wu, JIANQIANG JIAO, Baolin Jiang

Due to the influence of economic development on the demand growth of coal resources, many mines in China have gradually entered deep mining. When the roof of deep coal seam is hard rock, it is easy to cause strong ground pressure with the advance of the working face, which seriously threatens the safety of coal mining. Taking 31,104 working face of a mine as the engineering background, this paper studies and compares the deformation characteristics and stress transfer evolution law before and after the presplitting of the hard roof through the combination of physical similarity simulation, numerical calculation, and field measurement, based on the analysis of the interaction relationship between the breaking and collapse of the composite hard roof, and verifies the treatment effect of hydraulic presplitting through field measurement. The results show that: (1) In the early stage of mining under the composite hard roof, the lower roof is mainly subjected to tensile failure, the voussoir beam structure formed is relatively unstable, and the stope is prone to impact. When the mining distance of the working face is large, the breaking rotation of the upper hard roof voussoir beam causes pressure damage to the lower hard roof, causing the lower hard roof voussoir beam structure to slide and lose stability, resulting in strong ground pressure in the working face. (2) After presplitting of composite hard rock stratum, in the early stage of mining, the range and degree of rock stratum damaged by presplitting are small except for the hard rock stratum itself, and the presplitting effect is not significant. When mining to the first square position, the roof is damaged in advance by presplitting, the overall plastic damage range increases, the damage form area increases, and the damage degree deepens. The vertical displacement of the composite hard roof increases rapidly, and the presplitting effect is remarkable. (3) The evolution characteristics of roof principal stress transfer show that under the dual effects of mining and presplitting, the roof tensile stress area above the goaf is large, the rock failure horizon rises, and the roof failure height is high and the failure degree is deep. The stress concentration degree of the coal mass in front of the goaf is reduced, and the stress concentration range is transferred to the rock mass in front. With the advance of mining, the hard roof in front can break and caving in time, so as to avoid rock burst disaster caused by large suspended roof area. The field ground pressure monitoring shows that the average periodic weighting interval, weighting range, peak value before weighting, and peak value during weighting of the working face after presplitting decrease by 53.5%, 38.03%, 8.63%, and 5.96%, respectively, which effectively reduces the weighting intensity and ensures the safe and efficient mining of the working face.

May 16, 2023

By J. Iannicelli

Spray drying is the principal drying method used in the production of over six million tons annually of beneficiated kaolin in Georgia. Thirty-three dryers in the Georgia Kaolin belt comprise the highest concentration of large tonnage spray dryers in the world. The steady growth of spray drying in the U.S. kaolin industry is paced by advances in design and development of large spray dryers which have led to large scale new applications in mining and related industries.

Jan 1, 1982

By Duk-Won Park

The stability problems of back- filled spoil banks became more important since the Federal Surface Mining Control and Reclamation Act of 1977 was enacted. The material properties of spoil banks were categorized as the first part of the study and spoil slope stability was evaluated using computer programs as a second part. Emphasis was placed on the effects of natural barriers, which is required in the federal law.

Jan 1, 1982

By Thomas M. Turner

Open pit mining, always a demanding task, faces two relatively new problems today: 1. Availability of equipment. Moderate to large draglines can take as long as 6 years from date of contract to date of operation. 2. Environmental restrictions. Strip mining in the minds of environmentalists compares unfavorably on the scale of social desirability to the activities of Jack the Ripper and Attila the Hun. Specifically, lowering of the water table to allow strip mining in the dry is being looked upon with increasing disfavor. The modern dredge offers relief in both problem areas. Delivery on a major dredge might run 18-24 months rather than 60; and lowering of the water table is precluded, thus minimizing environmental objections. In addition, a lower first cost and potentially increased efficiency may offer real advantages to the miner who is forced away from his traditional mining methods. This talk is dedicated to acquainting the miner with dredge types, advantages, and limitations.

Jan 1, 1975

By T. G. Melkus

A Setaram C-80 heat flux micro- calorimeter was used to study the surface and interfacial properties of fine coal particles in water containing flotation agents via heat of immersion measurements. Heat of immersion (?Himm) is usually a small exothermic quantity and can be used' to characterize a solid in terms of its relative hydrophobicity or hydrophilicity. The effects of coal type, surface oxidation, mineral matter content, kerosene concentration, and pH on the wetting characteristics were investigated. Results obtained from the calorimetry experiments correlated well with results from independent flotation experiments.

Jan 1, 1987

By Ernst P. Hall

As a scientist and an engineer whose responsibilities include the consideration of air pollution and its control, I am frequently called upon to answer variations of two basic questions, These questions may I be set forth as: (1) How much air pollution does the coal industry cause? (2) How serious is the air pollution problem to the coal industry? At first these questions may seem elementary and almost trite, but serious consideration of them will show that they are technologically involved and I further complicated by the subjective base to which they must be evaluated.

Jan 1, 1963

By Harold L. Lovell

The extensive heterogeneity of coal is a fact long recognized by scientists and engineers. However, until recent years the practical implications of such heterogeneity have more often been realized from an undesirable experience than from knowledge or forethought. Variations in the properties of coal, even within the same seam, eventually lead to procedural modifications in mining, handling, preparation and utilization. The concepts considered here propose an enhanced application of information, detailing these properties, realizing the uniqueness of any given coal seam but the practicality of a common approach. Coal preparation practice has been designed primarily for the control of ash and sulfur content to meet market specifications which are similarly specified, Other physical characteristics of size and friability are also commonly employed and, to a lesser extent, properties which are implications of rank. The consideration of petrographic data as indicators of origin, thus total physical and chemical properties, has generally been overlooked as a realistic tool in-the exploitation of coal as a resource. The evolution of descriptive techniques, whether petrographic, physical, or chemical, capable of universal application with any rank of coal, is still beset with problems.

Jan 1, 1968

By David R. Hargis

Large-scale groundwater withdrawals are necessary to depressurize a confined aquifer system allowing the dry open-pit mining of the overlying phosphate ore. The extent of the existing and planned groundwater development led to the establishment by the State of North Carolina of Capacity Use Area No. l. Groundwater use in the Capacity Use Area is regulated by a permitting system. A two-dimensional finite-difference ground- water flow model was developed for North Carolina Phosphate Corporation. The aim of the model is to aid the Corporation in matters relating to permitting by serving as a predictive tool. The model can be used to project regional water level impacts resulting from various scenarios of depressurization pumping.

Jan 1, 1983

By Thomas J. Ferree

A Reichert cone concentrator was installed in an aggregate plant circuit to recover the extremely fine "flour gold" known to exist in the deposit. The gold content of the bank-run gravels averages about 0.1 grams per ton (about $1.45 per ton), based upon $14.47/g (345O/ounce) gold. Tine Reichert cone, in conjunction with a conventional shaking table, re- covers in excess of 85% of the gold. A screen analysis of the gold particles shows 44.1% is -i4 microns (-200 mesh) in size. The plant operates with a two-man crew.

Jan 1, 1981

By Lewis J. Patterson

In the period of time allotted to this paper, an attempt will be made to cover a great deal of territory, figuratively speaking, as far as our experience with ammonium nitrate is concerned. In giving this subject the "broad-brush" treatment, it will be necessary to generalize on the major points which at the same time will permit me to avoid, to a great extent, any involvement in the purely technical and theoretical aspects of blasting. The practice of theorizing before a new idea is tried has practically been discontinued in our organization simply because experience has shown that, almost without exception, theories have fallen aside as some new development takes its place. In regard to blasting, logic and experience seem to have little place in this phase of quarry operations. As the use of low cost blasting agents was introduced in our operating practice, a man who had no previous experience in the field of blasting but with sound knowledge in safety procedures was given the responsibility of supervising the drilling and blasting operations. A total lack of experience is not ordinarily recommended as a prerequisite to assuming the responsibilities of a supervisory position. However, in this case it was obviously a wise decision because there were no pre-conceived ideas as to what techniques would or would not be successful.

Jan 1, 1958

By Devraj Sharma

This paper presents technical issues in the design and management of a retorted oil shale disposal site. Major physical and geochemical mechanisms which affect the disposal are: heat transport, moisture migration, chemical species transport, auto-ignition, and mechanical behavior alterations of the retorted oil shale pile. The interaction of these mechanisms and their relative magnitude will affect the environmental behavior of the pile. The paper discusses the coupling between the mechanisms, presents a framework to quantify the processes by laboratory and field measurements, and in addition discusses the use of mathematical models to provide quantitative predictions.

Jan 1, 1981

By Kenneth A. Pietila

The thickening and dewatering characteristics of refuse slurries are as variable as the coal mining operations and preparation plants that create them. This paper discusses these characteristics based on field studies at a number of mine sites. The connection between bench and full scale performance is confirmed with the design, construction and operation of an integrated 18m (60 ft) diameter thickener and 2.5 meter belt filter press system in Western Kentucky. The data from this system are presented.

Jan 1, 1984