Search Documents

By VIVEK KUMAR HIMANSHU, Murari Prasad Roy, Kaushik Dey, Rakesh Kumar Singh, Ashish Kumar Vishwakarma

Sublevel stoping is the most popular and practiced mining method in underground hard rock mines. Proper planning and its execution is the key requirement for stope extraction using this method. The stope extraction has been a challenging task since decades. The major reason is the unavailability of free faces as compared to opencast bench blasting. The geological and geotechnical parameters change gradually even within the stope itself. So, the blast design parameters should be planned according to the scenario of the upcoming ring. The blast design parameters like burden, toe spacing, inclination of blastholes, diameter of blastholes, charge density of explosive, etc., play an immense role in the rock damage. For the proper breakage of rock, the movement of burden is the prime objective. To study this, an explicit dynamic based modeler of M/s Ansys was used. The burden values were varied from 20 to 65 times of blasthole diameter to assess the optimum burden value during the study. The models were simulated for the rock having uniaxial compressive strength as 35 MPa and 102 mm blasthole diameter. Three holes were simulated having depth around 14–14.5 m. Different blast design parameters and respective blast-induced ground vibration have also been measured at the experimental site. The core samples of the rock present at the experimental site have been used for the evaluation of geotechnical parameters. These geotechnical parameters were used in the simulation models. The volume of rock excavated along the free face has been calculated in each model by varying the burden. It has been found that the burden value can varies from 35 to 40 times blasthole diameter (3.6–4.1 m) to achieve a greater volume of rock along the free face for 102 mm blasthole diameter and rock of 35 MPa uniaxial compressive strength.

Dec 22, 2023

By Paul C. Miclea

Hanford Reservation, in the State of Washington, with its deep basalt formations, is one of the three sites recommended by the Department of Energy for detailed investigations in order to select the first nuclear waste repository in the United States. Information obtained from several deep bore-holes drilled at Hanford indicates that the underground facility can be developed in one of the major basalt flows belonging to the Grande Ronde Formation in the Columbia Plateau, at depths greater than 3200 ft. One of the main concerns in the underground repository design is the achievement of acceptable environmental conditions during the development and the operation of the repository. For this, ventilation and air-conditioning are of prime importance and should be fully addressed. Besides the factors that determine the airflow requirements to meet the personnel and equipment operation needs, there are two major concerns that impact on the ventilation system design: the temperature of the in situ virgin basalt rock and the influx of groundwater. These two factors are related by the fact that the groundwater has the same temperature as the rock itself and they both constitute main sources of heat underground. Current information indicates that the temperature of the virgin rock at a depth of around 990 m (3250 ft) is 52°C (12S°F). However, there are some indications that the rock temperature at the selected horizon might be higher. This paper addresses the impact of the virgin rock temperature on the ventilation system and air-cooling requirements. Graphs with heat loads and cooling required for different rock temperatures have been prepared for a given model and network, using computer techniques for simulating the climatic parameters.

Jan 1, 1987

By P. D. Georgescu

Gold, like no other metal, has a fascinating and special place in the world. It is used in a range of every day applications essential to modern life. Gold has long been considered the most precious metal in the world. Gold is used mainly for making jewellery as well as for dentistry, adornments on building and artistic expression. For thousands of years it has been used as an ornament of kings, a currency and standard for global currencies, and more recently, in a wide range of electronic devices and medical applications. Gold?s many unique properties have secured in a central role in history and human development. Today, more often than not, gold is extracted from ores. It occurs in vein and alluvial deposits and is often separated from rocks and other minerals by mining and processing operations. Some of these processes cause environmental concern (cyanidation, amalgamation, roasting). Besides primary gold ore resources, a series of secondary resources can be taken into account and processed for gold and silver recovery. There are two main types of waste produced. The first type is process waste, which includes tailing consisting of processing residues and waste rock. The other type is refuse from other different processes and recyclable materials. Among other secondary resources and/or by-products containing precious metals, which have been studied some processes and technologies with low ecological impact are presented in this paper. Heaps and tailing ponds resulted from gold-bearing ore exploitation and processing, refractory gold-bearing pyrite concentrates, slag resulted from electrolytic slime melting, gold-bearing chlorous slime are taken into account. In order to establish environmental friendly technologies for precious metals recovery from these secondary resources, laboratory experiments have been carried out on a pilot scale and in some cases on semi-industrial scale by applying specific technological processes, namely hydro-gravitational concentration, bio-oxidation, non-ionizing electromagnetic radiation (microwaves), solubilization without utilizing cyanide and gold recovery by ion-exchange resin. This paper presents the research results, technological principles as well as the possibilities of applying combined processes in order to treat different secondary gold-bearing resources.

Jan 1, 2006

By R. L. Grayson

In 2010, MSHA began holding hearings on a new coal mine respirable dust rule, which proposes a 1.0 mg/m3 standard, a separate 0.1 mg/m3 quartz standard, and the use of single-shift samples for compliance. Small mines largely comprise the ?hot spots? where dust diseases of the lungs increased dramatically over the past decade. This paper presents findings on the feasibility of small mines? compliance with the proposed new 1.0 mg/m3 standard. It gives probabilities of noncompliance by MSHA district, seam height, and selected ?hot spot? counties. Because silicosis and respirable quartz dust appear to be the primary issues related to a recent doubling of the prevalence of dust diseases of the lungs, multiple regression models for prediction of the average total quartz content of compliance samples are given. These findings have significant implications on the need for better dust control methods.

Jan 1, 2012

By M. Karmis

The determination of the surface area which may be impacted by underground mining is an important consideration in subsidence engineering. A number of parameters have been utilized to identify this influence area, most notably the angles of draw and break. This paper discusses the implications of selecting an appropriate "damage angle" for defining a potential damage area due to mining, within which surface structures may be impacted Furthermore, the influence of both mining and geological factors, such as mining width and depth and overburden lithology, on this angle is examined, using the Surface Deformation Prediction System (S.D.P.S) software. Finally, recommendations are given for applying these concepts in subsidence control.

Jan 1, 1994

By Terry W. Mellors, Robert J. F. Goodfellow

The underground industry has been forced to reconsider risk management sincethe introduction and implementation of the “Joint Code of Practice for Risk Management of Underground Works in the UK” published in 2003 and the subsequent international version published by the ‘International Tunneling Insurance Group’ (ITIG) in January 2006.What does this mean for major tunnel projects in the US and elsewhere? The discussion will highlight the implementation of the Codes to date, risk management principles embodied in the Codes and the use of risk registers as a projectmanagement tool and the management of risk.

Jan 1, 2007

By Philip L. Hageman, Paul H. Briggs

An important tool for use in the geochemical assessment of abandoned mine-waste piles is a leach procedure that can easily be done in the field and used for on-site screening of historic mine-waste material. We have developed a simple field leach test that is an effective indicator of waste pile geochemistry and can be used in order to establish the relative geochemical fingerprint for a given pile. This simple procedure also provides indication of the potential chemical composition of run-off from the weathered surface of these piles. As part of developing the technique, a comparative study was carried out on eight mine-waste composite samples from different deposit types. Splits of all eight composites were leached using the field leach test procedure and a modified version of EPA Method 1312 (SPLP). We found that the field leach test consistently provides relative indication of leachate geochemical trends comparable to leachate data derived from the more regulated, time consuming and laborious EPA Method 13 12 (SPLP).

Jan 1, 2000

By Vladimir J. Ovdenko, Sergey N. Lazarenko, Evgeny L. Schastlivtsev

The term sustainable development shortly appeared in international use in the run of UNO Environmental Protection Conference held in Rio de Janeim in 1992, bears the concept, that evolution process ( associated either with a region or society) should provide mutual interests concern in three aspects - environmental, economic and social ones, admitting as well the fact , that environmental protection should become an integral part of each process and cannot be regarded separately. In this connection it seems quite reasonable to employ the principal of sustainable development, while creating the model of industrial mastering the territory constraint lands viewing their future, for a example, in rich mineral deposit's development. In Kuznetsk coal basin in Russia ( west Siberia) the development of a big coal deposit Erunakovsky is now being underway. The major part of coal will be mined with open cast method, resulting the number of local environmental adverse impacts' occurrence. In such a situation mastering of sustainable development model is given the top priority, demonstrating the essential result of its application in a form of possibility to define the best correlation between economically expedient and environmentally tolerable loads during coal mining. The given paper is an attempt to work out the main principals to approach the creation of sustainable development model in regard of the definite region case. To simplify the presentation of employed approach's main idea, the given below accepts as its component only one of many actually existing environmental profiles, that define mining pro- cess impact on environmental situation -the size of infringed (de- graded) lithosphere surface. Basically, the actually existed correlation between spheres. grounding the model of sustainable development - economic, environmental and social- is given in a form of nomogram under Fig.1. On the presented graph the prognostic values of broken lands relative extent within Erunakovsky boundary ( to be compared with total region area taken as 100%) are arranged on axis x". Axis "y- demonstrates the main values associated with complete economic background, making the intrinsic part of the principal for sustainable development, i.e. annual coal output for the given area. It's top, used in assessment value relates to actual showings implied for the study region project and quantifies 60 min. tons. While regarding the social facet of principal for sustainable development, the applied mode to separate social issues into two types - one profiling a welfare standard of living and the other. pertaining the way environmental situation contributes to the degree of &ologica-1 comfort in people's living was defined as the most expedient and the most adequate in the matter of reflecting the actual terms of vital activity of the society. In accordance with the cited above the economic level showings are plotted on the graph on "-x” axis, while "-y" one obtains the values associated with the point of ecological comfort presented in conventional units. For the maximum possible conventional point of living (corresponding in nomogram to 1.0 value) a welfare level secured with industrial region economic activity revenue was assumed in case the top planned annual amount of coal is delivered ( 60 min. tons). While studying the index of public economic welfare, environmental conditions corresponding level in its original state i.e. prior to any industrial work carried in the region, was adopted as its top possible conventional rating (1.0). The given nomogram displays the integrity of x-f(y) type interrelations plotted on the basis of four separate dependencies, precisely a) the size (area) of infringed earth's surface as a function of coal output in the region; b) subordination of ecological comfort of people's living to the degree of lands infringement; c) interconnection of economic and environmental components of people living; d) interconnection of economic level of people's living and the amount of coal mined in the region. Linked to a single unit, these separate plain dependencies create, as seen from the graph, a more intricate system of bonds, that affords during defining or changing this or that system parameter to secure undergoing changes, that occur to other parameters of the system. The mentioned reason made it possible to consider and drive to mutual conformity ( as far as it is possible) all parameters values for the defined system's relations, that in their turn indicate the concern of other aspects of a sustainable development principal. According to the graph, in order to get not more than 50% of infringed land left after the deposit's mining, it is advisable to ex- tract not more than 40 min. tons of coal annually, gaining in this case the level of ecological comfort for living in the amount of not

Jan 1, 1996

By Alim Elibol, Rosbel Jimenez, Mustafa Can Suner, Deniz Tuncay, Zach Agioutantis

LaModel is a displacement-discontinuity variation of the boundary element method, which is utilized to analyze the displacement and stress in flat-lying, tabular orebodies. In coal mining, the accuracy and reliability of LaModel are proven with the utilization of the Mark- Bieniawski coal pillar strength and the stress gradient formula with proposed methodologies. However, the application of LaModel is limited to coal mines due to the default coal pillar strength properties. Recently, the stress gradient functions have been established and used to derive concentric rings of zones to simulate stone mine pillar yielding in LaModel. Also, to gain a robust understanding of the brittle failure mechanism and its effect on pillar strength, an S-Shaped failure envelope, where rock mass' cohesive and frictional strength components mobilize as a function of confinement (e.g., minimum principal stress), has been implemented into FLAC3D software. Therefore, by employing brittle failure criteria, the pillar strength stages at various width-to-height ratios and different pillar dimensions are estimated for four benching stages. The estimated pillar strengths and stress gradients for benching conditions are then used to calibrate LaModel in-seam material properties and compare stresses computed by LaModel and FLAC3D. Consequently, this study aims to increase the safety measures in the stone mining industry by implementing the practical use of LaModel for underground stone mines' initial development to various stages of bench mining.

Jun 25, 2024

By C. F. Barter, H. G. Kreis, D. S. Weber

Before and during in situ mining at the Santa Cruz In Situ Copper Mining Research Project test site, hydraulic testing was conducted at injection and recovery test wells to characterize patterns of fluid movement in the 5-spot well field. Testing included borehole spinner flow meter surveys, single-well and multiple-well injection and recovery tests, straddle packer injection tests, and bromide pulse tracer tests. Results of hydraulic testing for determination of fluid flow regimes were used to modify well and mining zone hydraulics for the purpose of increasing fluid migration in flow pathways of the mining zone with higher copper grade.

Jan 1, 2000

In bump-prone coal mines, roof and rib support is subject to dynamic as well as static loading. Although less frequently encountered, the dynamic loading component can result in violent coal expulsions into openings seriously threatening the safety of workers. Dynamic support systems that have been increasingly implemented in many deep hard rock mines for dynamic failure containment have not yet found their adaptation to deep coal mines at desired levels. This paper examines the potential use of some of these dynamic support systems in deep coal mining, particularly in the western United States. Fundamental principles of dynamic loading are reviewed in the context of their application to dynamic failure mechanisms in coal mines. Potential benefits and applicability of the suitable hard rock dynamic support systems are discussed in relation to coal bump mitigation. The resulting insight provides a starting point for development of dynamic support elements for bump prone conditions in deep coal mines.

Jan 1, 2009

By C. A. Fleming, R. G. Williamson

Process development for Eskay Creek began in early 1990 at Lakefield Research, and was initially focused on producing a high-grade/high-recovery concentrate for sale. Owing to the significant base metal sulphide (Cu, Zn, Pb) content of the ore, such a product would have made an attractive feed to a copper smelter, while a gravity and/or flotation flowsheet would have circumvented many of the environmental permitting problems that were anticipated. In the event, it was found that neither gravity nor flotation (nor even a combination of the two) was able to produce a discardable tailing and, in late 1990, attention shifted to the development of a hydrometallurgical flowsheet.

Jan 1, 1995

By Micheal Mitariten

The recovery of natural gas (primarily methane) from coalbed deposits is an established and growing source for the U.S and accounts for over 7% of its total production. The gas from on-purpose degassing is often pipeline quality and requires only compression and dehydration before being admitted to the pipeline grid. However, the raw gas is sometimes contaminated with nitrogen (N2) and/or carbon dioxide (CO2) that can make the gas inadmissible to the transportation pipeline. In general, the N2 must be 4% or less and the CO2 should be 2% or less. In treating gas produced from virgin coal bed or from degassing operations where CO2 is present, amine systems are traditionally used for its removal. Engelhard’s Molecular Gate® adsorption system offers an attractive alternative due to its skid-mounted equipment, low pressure and unattended operation, cost and high on-stream reliability. Natural gas can also be sourced from the residual coal, after the coal has been mined. This source can be the GOB or gas remaining in abandoned coal mines. This source is almost universally contaminated, often with a combination of CO2 and N2. If the source is from air intrusion, the source can also be contaminated with O2. In treating CO2 / N2 contaminated feeds, the Molecular Gate adsorption system removes both of the impurities along with a level of O2 within a single processing step. To date, ten Molecular Gate units are underway with three systems having been installed for upgrading gas from abandoned coal mines. The technology consists of specialty adsorbents and advanced PSA processes that are jointly offered as fabricated packaged equipment by Engelhard Corporation and Guild Associates, Inc. Upgrading requirements, project challenges and project arrangements are discussed in this paper.

Jan 1, 2005

By M. E. Kravetz, E. B. Milosavljevic, L. R. Solujic

Gold ores containing high levels of cyanide-leachable copper minerals, such as covellite, chalcocite, bornite, malachite, azurite, and cuprite have traditionally been difficult to treat economically. A novel hydrometallurgical process for efficient treatment of cyanidation effluents obtained by leaching high copper gold ores (or concentrates) based on the use of Cherokee Chemical organo-sulfur reagents (OSR-A, OSR-B and OSR-C) is described. The process may be modified to selectively precipitate silver, or completely recover silver, copper and zinc, as well as regenerate significant amounts of cyanide. For example, data obtained demonstrate that 100 % of silver and zinc, and 98 % of copper were removed from the solution, while 80 % of cyanide was recovered. The treated barren solutions exhibit enhanced gold and silver leaching kinetics compared to the untreated controls.

Jan 1, 2004

By Anthony Delvescovo, Gregory F. Aluce, Joseph A. Sopko, Lyle C. Smith

Construction of a 13m shaft through approximately 100m of water bearing soils and another 100m of bedrock was attempted using the Slurry Diaphragm Wall Method with a combination of deep dewatering wells. During excavation within the slurry wall, unexpected groundwater inflows occurred in a structure of loose silty sands. Artificial ground freezing was selected as a remedial method to seal the leaking slurry wall, and as a primary excavation support and groundwater control method for the 30m of overburden material below the base of the wall. Design of the ground freezing system required analysis of both the structural requirements of the unsupported soil, the frost effects against the existing slurry wall and the groundwater control in the area of the breech in the wall. These design procedures are summarized, and construction and excavation techniques and corresponding schedules compared in this paper. Advanced drilling techniques, ground freezing quality control and general contractor procedures for efficient shaft construction are discussed.

Jan 1, 1993

By Randall Morris

After years of steadily declining employment and production, the U.S. coal industry is having a moment. In 2016, when Donald Trump was running for U.S. President, he cast a spotlight on coal mining in his campaign speeches, promising to end the “War on Coal.” Fast forward to 2025. On the first day of his second term, President Trump signed the National Energy Emergency Act, which emphasizes domestic energy production as a matter of national security and focuses on incentivizing domestic energy resources. Then on April 8, President Trump issued an executive order opening federal land to coal mining to reinvigorate “America’s beautiful clean coal industry.” As the nation seeks to identify reliable solutions to meet its ever-growing energy needs, the administration is going all in on proven, reliable and readily available natural resources, including coal. This means the coal industry is positioned to play a pivotal role in the administration’s stated energy policy, and highwall mining could be an integral factor in helping the industry optimize the extraction of ore to make the most of this moment. The White House noted in a statement that the United States’ “abundance of energy and natural resources … have historically powered our Nation’s economic prosperity” and vowed to remove regulations that have hindered developing these resources — regulations that resulted in job reductions and higher energy costs for U.S. consumers, while weakening national security. “There has been an increase in electricity prices in the United States of over 30 percent in the past four years,” said Rich Nolan, president and chief executive officer of the National Mining Association (NMA). “This administration wants to focus on that, inflation and on increasing electricity availability to help lower the price over time by incentivizing energy policy. Coal is definitely a high priority for this administration.” Part of the White House’s strategy is to facilitate investment in coal-fired plants. The shift comes at a time when the reliance of coal-powered energy plants has been waning. According to the U.S. Energy Information Administration, 7.5 GW of electrical capacity from coal-fired plants was retired in 2024, following the retirement of 22.3 GW of electric generating power the two years prior.

Jun 1, 2025

By Ronald M. Tipton

Freeze and thaw deterioration is a serious problem In con¬crete pavements. The main cause of distress Is thought to be the pore structure of coarse aggregate. In an attempt to characterize deleterious pores, the Iowa Pore Index test and the Expected Durability Factor, as Calculated from the mer¬cury intrusion porosimeter, were devised. This study Included freeze-thaw and sodium and magnesium sulfate soundness testing of sixteen carbonate aggregate samples. In addition, the Iowa Pore Index and the Expected Durability factor were determined for each of the samples. All of the Above mentioned physicochemical parameters were examined using bivriate correlation analysis with the In¬tent to evaluate the effectiveness of the Iowa Pore Index and Expected Durability factor for predicting the frost dur¬ability of an aggregate. The results from the bivariate correlation analysis showed no significant correlation, between the Iowa Pore In¬dex And- Expected Durability factor with the other physico¬chemical parameters investigated. Rust interesting is that the Iowa Pore index predicted that All of the tested samples would resist freeze-thaw failure, whereas the Expected Durability factor predicted that -ash sample would he non-durable.

Jan 1, 1987

Mineral liberation data are routinely obtained for a wide variety of applications, including ore characterization and characterization of various metallurgical test products obtained in bench-scale laboratory testwork. Newmont Mining Corporation owns several properties in the Carlin Trend containing refractory gold ores. These ores are generally difficult to treat and have to undergo several processing stages for gold recovery. At Carlin?s Mill 5 operation, flotation is used to pre-concentrate some of these difficult ores to produce a sulfide concentrate to feed the roaster. It is of interest from a flotation perspective to be able to study the floatability of pyrite, arsenopyrite and arsenian pyrite, since these minerals all have different quantities of gold associated with them, and have to be recovered to ensure a successful separation has been achieved. In this paper, a detailed MLA study on several Carlin ores was undertaken on samples from flotation tests, using air or nitrogen as flotation gas, specifically to study the differences in floatability characteristics, which ultimately impacts overall gold recovery. I

Jan 1, 2009

By S.K. SHARMA, ANKUSH GALAV, G.S.P. SINGH

This paper proposes a hydromechanically coupled numerical modeling approach to quantify the influence of various parameters on the mechanical and hydraulic performance of protective water barrier pillars (PWBP). The results are validated for two case studies having pillar widths of 16 and 42 m at cover depths of 136 and 190 m and water heads of 25 and 141 m. The outcome can be significantly helpful in the rational design of these pillars in underground coal mines.

Mar 1, 2023

By William H. Langer

U.S. Geological Survey (USGS) recently initiated the Front Range Infrastructure Resources Project. This is a multidisciplinary study along the Rocky Mountain Front Range from Pueblo, Colorado, to Cheyenne, Wyoming, and is designed to collect, compile, and analyze new and existing data on natural aggregate (stone, sand, and gravel), as well as water, and energy resources. To identify aggregate resources in the Front Range, a 1:500,000-scale reconnaissance map showing locations and quality of both bedrock and surficial sources of natural aggregate in the Front Range urban corridor was prepared by processing the digital geologic maps of Colorado and Wyoming. The first step of the process was to identify map units as either bedrock or unconsolidated material. Bedrock was classified according to type (i.e., limestone, granite, gneiss, etc.), which in turn was classified based on the suitability of the bedrock for use as crushed stone. Unconsolidated materials were classified according to relative age, with the older, more weathered materials being defined as less suitable for use as aggregate than younger materials. As a spin-off from the Front Range Project, the techniques developed for analyzing the Front Range geology have been modified and expanded to include all of Colorado and New Mexico. More detailed digital aggregate maps (1:24,000 scale) are being prepared in collaboration with the Colorado Geological Survey (CGS). Maps from the CGS "Atlas of Sand, Gravel and Quarry Aggregate Resources, Colorado Front Range Counties" show the distribution of potential resources of sand and gravel and provide general information about the physical properties of the resources. These maps are being digitized and merged into a single Geographic Information System (GIS) data base. In addition, the project is adding more specific information to the maps about deposit thickness, volume, and quality. This additional information is being obtained through field-characterization studies and modeling activities. The GIs data base can be displayed and queried using off-the-shelf software such as ArcInfo?, ArcView?, and Map Professional?. In addition, the USGS is developing a decision-support system to assist users in analyzing various land-use options on resource availability.

Jan 1, 1999