Search Documents

By A. L. Boerner

Off-highway tire costs represent a significant portion of the total mining costs in openpit, truck-shovel operations. To extend the lives of tires, the site-specific factors influencing tire life should be investigated Valuable data can be obtained by combining historical operational data captured by a mine dispatch system with detailed tire and maintenance histories. Assuming that failure counts satisfy a Poisson distribution, F-tests can be applied to determine significant deviations from desired or target counts. The methodology developed in this paper can be used to identify the haul routes and loading and dumping zones that have significantly higher incidences of tire failure. Corrective action can then be targeted at these zones by modifying the shovel or truck operator practices; changing the haul route maintenance and clean up practices; or altering the bench, ramp or waste dump design parameters. An example is given of the correlation of tire separation and tire impact failures with haul routes for a fleet of nine Caterpillar 793C trucks in operation at the Chuquicamata Mine in northern Chile. A high incidence of impact failures was observed for the ex pit ore crusher and for tires installed in the left outer rear position on the trucks. The latter was postulated to be due to a preference for drivers to execute right-hand turns prior to dumping. Recommendations were made to revise crusher and dump cleanup practices and investigate the feasibility of super-elevating the surface of dumping zones to reduce ground pressure on the left rear tires.

Jan 1, 2002

By R. R. Oder, R. J. Gray

We report measurements of the effects of rank, type, and grade of coal on grinding energy and grinding media consumption in a Pitt Mill. The rank of coal has a greater effect on grinding energy than does coal type. The effect of coal grade on grinding energy depends upon the relative grindability of the mineral matter and of the hydrocarbon components of the coal. The mineral matter is primarily responsible for abrasive media wear in a Pitt Mill. The widely recognized HGI test for coal breakage may yield misleading results, particularly for multiple-banded bright and dull coal where the screening procedure used in sample preparation favors the testing of the hardest coal fraction. The work reported here indicates that the Pitt Mill, which grinds the whole coal in a single stage and which yields easily interpreted results, is an excellent candidate for testing coal pulverization characteristics including energy requirements and equipment wear. The measurements of the effects of coal characteristics on grinding energy and on media consumption have been used to estimate the cost of fine grinding in a Pitt Mill. The results, based on a conceptual level evaluation of grinding at the rate of 1 TPH, show that there are trade-offs possible between the cost of energy and cost of media consumption which involve choice of grinding media size. The use of fine-size grinding media to lower grinding energy and to increase throughput can be deceptive because the total cost of grinding must consider both energy and media consumption.

Jan 1, 1992

By Slawomir Bock

One of the fundamental issues having a great influence on the safety of operations performed in underground mines is the support of workings which should assure their stability in a given geological setting and mining-technical conditions during the life of their use. The process of designing and planning support for roadways may use analytical and empirical, as well as numerical methods. In view of the rapid increase in the data processing capacity of computers and the development of more and more enhanced software for numerical modeling, it seems to be advantageous to use numerical methods in searching for design solutions ? especially in the case of non-typical mining and geological conditions and in cases that need to take into consideration a great number of factors. The assessment of rock mass quality is of basic significance in designing mine supports. Fractures, dividing the rock mass into blocks, have an essential influence on the stability of the rock mass and underground construction. This paper presents examples of the fundamental underground investigations on the rock mass conducted by the Department of Extraction Technologies and Mining Supports of the Central Mining Institute in Poland, such as: penetrometric tests, introscopic examination, laboratory testing of rock samples and ground penetrating radar. Moreover, this contribution also presents examples of applications of three-dimensional numerical modeling for the purposes of stress-strain analysis of the rock mass around mine workings and computer-aided support design by means of FLAC3D (developed by Itasca) and Cosmos/M (developed by Structural Research and Analysis Corporation).

Jan 1, 2009

By L. Yuan

To reduce fire hazards from spontaneous combustion of coal in longwall gob areas, a series of computational fluid dynamics (CFD) simulations were conducted by National Institute for Occupational Safety and Health (NIOSH) to model the spontaneous heating of coal in longwall gob areas. The previous modeling results demonstrate that spontaneous heating of coal usually occurred behind the longwall shields and along the face with a bleeder ventilation system. Assuming a stationary longwall face, the spontaneous heating could turn to a spontaneous fire in several days for the most reactive coal under favorable conditions. When the longwall face advances, the spontaneous heating process will be significantly affected. In this study, the effect of longwall face advance on the spontaneous heating in the gob area is investigated using the CFD model developed in previous studies. One longwall panel with a bleeder ventilation system is simulated. The width of the panel is 300 m, while the length of the panel is changed between 1,000 to 2,000 m. The same permeability and porosity profiles are used for gobs with different lengths. The spontaneous heating first develops in the gob when the longwall face is stationary. Then, the face advances at a certain rate. The face advance is simulated as a series of discrete movements, and the effect of the face advance on the maximum temperature developed during the face stoppage is examined. Disclaimer: The findings and conclusions in this report are those of the authors and do not necessarily represent the views of the National Institute for Occupational Safety and Health.

Jan 1, 2009

By A. Vien

Over the past several years, Svedala has developed a continuous charge monitor (CCM) for tumbling mills. It consists of a strain gauge embedded into a rubber lifter and associated electronics. This paper describes the results of a research program to evaluate the technical and economical merits of such a device on a SAG mill. The evaluation includes validation through discrete element modelling and comparison to measured static volumetric load. Inclusion of the measurement into a control strategy and its potential for condition monitoring is discussed.

Jan 1, 2001

By Joseph Irons, David Westfall

Three rock tunnel sewer systems are underway in the Chicago Area. (Figure 1) The three are designed to act independently and to be later connected to the future tunnels of the master plan. The tunnel excavation for each of the systems has been completed. One is in the Northwest area within the City being built by the City, known as the Lawrence Ave. System. Another is in the Southwest suburbs, known as the LaGrange-Brookfield Sewer or Southwest 13A, being built by the Sanitary District, the third is in the South suburbs called the Crawford Avenue sewer or Calumet 18-E, Ext. A- being built as a joint venture between the City and the District. The three are similar in that they have the same purpose, the same component parts and their tunnels were constructed in the nigaran limestone using a mechanical mining machine. The purpose of each of the systems is two-fold. First to provide flood relief for existing inadequate sewer systems, and second to reduce the pollution load to the waterways caused by combined sewer overflows. The existing systems in the areas to be relieved are combined sewers built many years ago. The main outlet for the Village of LaGrange, for example, was built in 1908, is badly in need of repair and lacks the capacity to handle the flood flow from the heavily urbanized area it now serves. The dry weather flow from the area is taken off by intercepting sewers. However during

Jan 1, 1997

By Rainer Kahrger

This paper is a follow-up to the paper presented at the SME meeting in April of 1996. Since then, the El Abra facility has been started up, 9 months ahead of schedule, and has processed about 45 million tons of ore and produced over 700 million pounds of copper. For those unfamiliar with the El Abra materials handling and leaching facilities, a brief overview of the facility is provided. The paper will then deal in detail with such aspects of Conveyor 103, the long regenerative overland conveyor, including: actual running resistance starting and stopping procedures emergency brake test at 10,000 t/h Additionally, we shall take the opportunity to report on a catastrophic culvert collapse in October 1996, which stopped the conveyor abruptly at full speed and under high load condition, causing a belt breakage. We would like to use this opportunity to thank the management of El Abra and Cyprus Amax for providing assistance and allowing us to present this paper. The El Abra team deserves a great compliment for building this one billion dollar facility in record time in a remote area of a high-altitude desert with no existing infrastructure, and for bringing it so quickly up to full operating capacity. The El Abra management had to assemble a completely new operator team. Considering the above circumstances, it took a great effort by all involved to achieve success. The official performance test which was required by the lending banks was successfully concluded in November 1997.

Jan 1, 1998

By Charles T. Ford

In 1971, Bituminous Coal Research, Inc~ established a program to provide the coal industry with the necessary information and technical capability to investigate and evaluate potential problems concerning trace elements in coal and coal-related materials. The initial efforts at BCR in developing or adapting analytical procedures for the precise determination of trace elements in the parts per million to parts per billion range were detailed in a report titled "The Development of Analytical Methods for Determining Trace Elements in Coal and Coal-related Products." A subsequent reports contained descriptions of reliable analytical methods refined by BCR for determining mercury in coal and coal ash and also in coal mine water. his paper reports initial progress in applying recently-acquired trace-element analytical capabilities to solving potential coal industry problems. In this case, the effect of a coal-cleaning process on the distribution and removal of potentially harmful trace elements in coal was evaluated. Coal cleaning offers the possibility of controlling potentially harmful emissions resulting from combustion of large tonnages of coal by removing the pollutants prior to combustion.

Jan 1, 1977

By G. Pan

A geostatistical approach is proposed for the design of infill drilling programs. The method is consisted of three major steps: developing geological favorability models, delineating mineralization and ore envelopes, and classifying reserves or resources. Geological modeling aims at developing favorable geological zones in which drilling is designed. Modeling mineralization and ore envelopes establishes criteria on potential blocks to be drilled. Top target blocks should be those included within ore envelopes. The framework of resource categories includes five types: probable reserves, indicated reserves, indicated resources, possible resources, and barren. Indicated reserves or resources are the top priority to be drilled for the definition of minable reserves. Possible resources may be considered as targets for further exploration. The algorithms involved in the analysis include indicator favorablity analysis, ordinary kriging, and indicator kriging. A case study presented here involves a gold deposit of Carlin type. The deposit was delineated by a sparse drilling program with 230 feet of average spacing. The infill drilling program designed by the new method suggests a significant reduction on the number of holes from a regular-grid infill drilling pattern.

Jan 1, 1995

By Warren E. Morrison

The expansion of the United States economy in the postwar period has had a tremendous impact on the demand for energy. Not only has total energy consumption increased at an unprecedented rate, but there have been major shifts in the composition or mix of energy resources within the end-use sectors. Because of the numerous interrelationships between substitutable energy resources and their markets, the energy economy can only be analyzed in terms of the trends of its component parts. This problem takes on additional complexity when attempting to chart the nation's future energy requirements. Total energy consumption can be forecast with reasonable accuracy for periods up to 15 years by relating this to projections of economic indicators. However, forecasting the component parts of the energy economy constitutes a dilemma in that the sum of the projected parts frequently exceeds predictions for total energy. Areas of uncertainty in energy forecasting tend to mount rapidly when proceeding from total energy to the consideration of specific energy resources consumed as fuel, power, or raw materials.

Jan 1, 1965

By C. D. Taylor, A. L. Mazzella, A. L. Martikainen

In fluctuating airflow, continuous air velocity recording is the most reliable method of air velocity measurement. It allows for fast recognition of changes and the calculation of long-term averages. Also, it enables the mine operator to identify when the airflow has decreased to a point requiring action. Using ultrasonic anemometers provides an accurate option for continuous air velocity monitoring. This paper provides information about the effect of common obstructions in underground mining on air velocity readings. Stationary and moving obstructions are used to represent workers and equipment that would cause discrepancies in measured airflow. Also, it is important to know how large of a sample size is required to ensure reasonable accuracy of results. Statistical analysis is used to evaluate the required sample size. The sampling procedure is further studied by comparing two different sample rates. The results show that obstructions provide noticeable differences in air velocity measurements. Also, movement of obstructions can be recognized from changes in results. Surprisingly small sample sizes provide reliable air velocity information. Standard sample rates are found to be suitable for the underground environment.

Jan 1, 2011

By Todd Burchett

Mining engineers spend countless hours and resources when designing a new underground coal mine. Their primary objective is to design the safest and most efficient operating mine with regards to coal production. A key variable often overlooked in this design stage is the slope conveyor. Typically, a slope conveyor is expected to operate with a 98-percent or higher availability. However, too often little effort is put forth by the mining engineer to optimize its design. Coal companies will rely on engineering, procurement, construction and management (EPCM) companies for the preliminary design, because the slope conveyor will be considered part of the surface material handling processes. This preliminary design will be used when soliciting quotations for the slope conveyor. Unfortunately, EPCMs may not have enough expertise with conveyors to optimize the design. This expertise is available with an original equipment manufacture (OEM) of conveyors, which ultimately may be responsible for supplying the slope conveyor. Each OEM will provide a bid package that represents what it considers to be the optimal design.

Jan 1, 2013

By M. R. Yalamanchili

Recently, noequilbrium electrokinetic measurements using laser-Doppler electrophoresis were reported by Miller et al. (1992) for alkali halides and the sign of their surface charge thus determined. These results are generally as expected from simplified lattice ion hydration theory with KCI, under normal circumstances, being the most significant exception. In this regard, lattice defects (F centers and oxygen imperfections) have been found to influence the surface charge of KCI and its electrophoretic mobility. In particular, the presence of oxygen defect states in the crystal lattice has been found to be responsible for KCI's unexpected behavior. The concentration of oxygen defect states in KCI, as characterized by UV/Vis absorption, was varied in order to study their influence on the electrokinetic behavior and subsequently on the flotation response of KCl. At low oxygen contents « 60 ppm) KCI is positively charged as expected from lattice ion hydration theory. However, typically, KCI contains substantial oxygen (>300 ppm) sufficient to impart a negative surface charge which accounts for the selective flotation of KCI from NaCl by hetero-coagulation with oppositely charged alkyl amine hydrochloride collector colloids.

Jan 1, 1994

By Y. J. Wang

The definitions of system pressure loss (mine head) and system resistance, which are traditionally associated with single-fan net- works, are applied to multiple-fan ventilation networks. The system characteristics -- relations among air power, pressure loss, air quantity and resistance -- are analyzed by introducing the concept of subsystems. These subsystems are associated with the fans located in a cutset of the network. For a multiple-fan network, the resistances for the subsystems and total system are dependent on the quantity ratios of the subsystems. In general the pressure loss of a subsystem or a total system does not vary as the square of the corresponding air quantity. If the quantity ratios of subsystems are all held constant, then the resistances become constant and the pressure losses are predictable from the quantities employing the "square law." The system resistance has a minimum value under the natural- splitting flow pattern. Being independent of the value of system quantity, the minimum system resistance provides a basis for comparing the different networks.

Jan 1, 1983

By M. H. Morcali

Pistachio nut shells, an agricultural waste biomass, and Lewatit TP 214, a commercial sorbent, were investigated as adsorbents for the adsorption of platinum from dilute hexachloroplatinic acid solutions. Before the pistachio nut shells were carbonized, adsorption percentage was 65%, whereas Lewatit TP 214 ensured almost 100% adsorption. However, after the pistachio nut shell was carbonized at 1,000° C under an argon atmosphere, the platinum adsorption (%) increased two-fold. The effects of such parameters as sorbent dosage, contact time, temperature and solution pH on adsorption were studied in detail in batch mode. The adsorption equilibrium data were best fitted with the Langmuir isotherm model. The maximum adsorption capacities, Qmax, at 25° C were found to be 38.31 and 33.22 mg/g for the carbonized pistachio nut shell and Lewatit TP 214, respectively. The adsorption of platinum on both sorbents was found to be described by the pseudo-second-order kinetic model. The results indicated that the activated carbon prepared from pistachio nut shells can be effectively used for the removal of platinum from acidic solutions.

By D. R. Spears

The Bureau of Mines has investigated the fundamental aspects of shear-flocculation using a rapid, in-situ particle size analyzer. Silica was stirred in the presence of an aliphatic amine to determine the effects of collector coverage, stirring speed, and solids concentration on the kinetics of shear-flocculation. The results showed that shear-flocculation is a two-stage process. In the first stage, mean particle size increased rapidly in the first 1-2 min of reaction; in the second stage, an equilibrium was set up between the rate of floc growth and floc decay. Collector dosage affected the position of the equilibrium by altering the number of surface sites for particle-particle attachment. A minimum stirring speed was necessary for shear-flocculation to occur and was dependent on solids concentration and collector dosage. This speed was the minimum necessary for particles to overcome the electrostatic energy barrier which kept conditioned particles dispersed. Larger particles flocculated more rapidly. At very high stirring speeds, large flocs became unstable, resulting in a narrowed particle size distribution in the slurry.

Jan 1, 1993

By William J. Miles

From a historical perspective, bentonite is the common rock term for various uses and applications. Its name originates from water-based muds near Fort Benton used for lubrication of wagon wheels during the 19th century migration to western territories (which are presently part of the United States) when the pioneers ran out of axle grease. From a clay mineralogy perspective, bentonite is composed primarily of montmorillonite, an expandable magnesium aluminum silicate clay mineral. When magnesium occupies an octahedral structural site that usually contains an aluminum atom, a negative charge is created. In order to neutralize negative charges, cations are drawn to the interlayer surfaces between clay mineral sheet structures. Modem applications for bentonite depend on the sodium or calcium cation populations and other characteristics of the clay mineral. When sodium is the dominant cation, the material is called sodium bentonite, also known as swelling bentonite, western bentonite or Wyoming bentonite. When calcium or magnesium is the dominant cation, the material is called calcium bentonite, also known as non-swelling bentonite w southern bentonite.

Jan 1, 2012

By J. Kretschmann, A. Müterthies, T. Rudolph, C. Yang, P. Goerke-Mallet

Catastrophic failures of dams and tailing storage facilities (TSF) have triggered the development of integrated ground monitoring concepts for hazard assessment, risk management and public safety. These concepts are based on knowledge and expertise of persons technically responsible for TSF. The aim is to combine this implicit and explicit knowledge with the data of in-situ- and remote sensors. Risk management for TSF must include a comprehensive monitoring program that integrates data from ground based-, air-borneand satellite-based sensors. Researchers at Technical University Georg Agricola (THGA) in Bochum, and EFTAS, Muenster, Germany, are fusing a variety of sensor data to enhance the capability and performance of TSF monitoring to ensure public safety downstream of TSFs. This paper describes the variety of sensors implemented in numerous research projects. It gives an outlook in terms of planned satellite missions with innovative equipment like hyperspectral sensors. The implementation of the data of these sensors in the analysis will increase the understanding of spatio-temporal impacts of mining activities. Future opportunities are explained by a datacube approach.

Mar 2, 2022

By Ian Farrell, Josh Stowe, Eric Wingeard

Tailings transport system design is generally based on identifying the minimum and maximum process boundary conditions for pump selection and pipeline sizing. The approach is robust and well-proven. However, the approach has the potential to skew selections to operating scenarios that have a very low likelihood of occurring, such as the combination of high solids throughput and low tailings solids concentration. The approach can result in a tailings transport system design that is overly conservative. A probabilistic method-based approach captures the independent variability of design inputs and the combined likelihood of outcomes. This approach identifies the process conditions that have the highest likelihood of occurrence and are most applicable to equipment and pipeline selections. An outline of a probabilistic-based approach to tailings transport system design and the resulting selections is provided in this article. The probabilistic-based system design is compared to the outcomes from the traditional approach. The benefits and challenges to this approach are discussed and recommendations for utilizing this approach for tailings transport system design are provided.

Mar 31, 2021

By S. W. Mao

Hydrologic and economic criteria figure in many obvious ways in water resources development, but they are rarely linked quantitatively, and most of the applications are pertinent only to the case-in-point. In the preparation of the Regional Plan for the massive program of ground water development in the Punjab, situations have arisen where the choice among two or more alternatives was made by analyzing the economic implications of critical hydrologic parameters. Two of these situations which are of more-or-less general interest are described herein. The first involves basic development policy -- whether ground water development should be based on the demand of the economy, or the conservation concept of safe-yield. The analysis demonstrated that mining of ground water is clearly indicated for areas where alternative supplies are unavailable. The second problem involves integrating hydrologic data into an economic model to determine optimum well design, From an analysis of all pertinent factors, a simple nomograph was derived which can be used to determine well specifications on-site during construction. The nomograph can be modified for use in any alluvial terrain.

Jan 1, 1967