Search Documents

By W. Miles

Introduction From a historical perspective, bentonite is the common rock term for various uses and applications. Its name originates from water-based muds near Fort Benton used for lubrication of wagon wheels during the 19th century migration to western territories (which are presently part of the United States) when the pioneers ran out of axle grease. From a clay mineralogy perspective, bentonite is composed primarily of montmorillonite, an expandable magnesium aluminum silicate clay mineral. When magnesium occupies an octahedral structural site that usually contains an aluminum atom, a negative charge is created. In order to neutralize negative charges, cations are drawn to the interlayer surfaces between clay mineral sheet structures. Modern applications for bentonite depend on the sodium or calcium cation populations and other characteristics of the clay mineral. When sodium is the dominant cation, the material is also called sodium bentonite, also known as swelling bentonite, western bentonite or Wyoming bentonite. When calcium or magnesium is the dominant cation, the material is called calcium bentonite, also known as nonswelling bentonite or southern bentonite. Swelling bentonite is recognized for its rapid hydration of interlayer sodium and subsequent dramatic expansion up to more than 20 times its original volume. Low shear can then disperse the hydrated sodium bentonite to form suspensions that increase viscosity and suspend solids. However, when shear is subsequently eliminated a sodium bentonite slurry gels. Characteristically, nonswelling calcium bentonite has relatively poor hydration properties and thus low expansion of the clay mineral. When subjected to low shear, calcium bentonite exhibits very little viscosity and poor suspension. Additionally, when shear is subsequently eliminated no more than minimal gelling takes place. The domestic and export markets related to both swelling and nonswelling bentonite are discussed below.

Jan 1, 2007

By S. Cotten

The regulations for current coal mine refuge alternative (RAs) require that there be sufficient life support to sustain survival of the maximum number of RA occupants for a minimum of 96 hours. This minimum duration assumes that rescuers can access the RA through the mine within four (4) days of the onset of the mine emergency. But what if mine rescue teams cannot reach the miners within the RA before the RA air supply is severely limited or exhausted? What could be done to extend the duration of the RA life support capability into the 97th hour and beyond? In addition, what might be done to enable more rapid rescue of the miners if they could not be reached through the mine in a timely manner? This paper describes a systems approach to address the potential need to extend the duration of RA life support beyond current design limits. New capabilities that need to be developed in advance of such a dire need include more reliable emergency communications, highly mobile and efficient drilling rigs, enhanced directional drilling techniques, and a standardized RA external life support interface along with RA internal design modifications to accommodate use of an external supply. The following sections describe the need, intent, and technology gaps associated with each of these capabilities. Government agencies and the mining industry should consider initiation of a program to investigate, design, and develop effective means of extending the current 96-hour time restriction on coal mine refuge alternative life support. The development process should begin with a focused study to refine the overall operational concept, investigate the current state-of-the art of critical technologies, identify specific technology development priorities, and make recommendations for a development program to provide in an organized, efficient, and timely manner a solution for extended refuge alternative life support and occupant rescue.

Jan 1, 2011

By Neil E. Izatt, M. Andre de Ruijter, Ronald L. Bruening, Wesley Young

IBC Advanced Technologies, Inc. has developed ligands, ?amed SuperLig®, which have specific applications in the gold mdustry. These ligands use molecular recognition technology (MRT). One ligand has been developed to selectively recover gold and silver from tailings solutions and from pregnant Merrill-Crowe solutions. Another ligand removes free cyanide, _ th10cyanate, other cyanide species, as well as copper and other base metal cyanide complexes from leached gold-ore solutions. The development of these "species selective'' SuperLig® prod­ucts allows for the more efficient operation of gold recovery processes and opens up the possibility of the economic devel­opment of high-copper gold ores. The resulting gold eluate is a high grade and a high purity stream which will simplify the need for further refming. Engineered systems based on MRT consist of a few unit operations utilizing standard equipment and mate­rials of construction. The process is simple to operate, thereby lending itself to automated modular design, which is both eco­nomic to manufacture and to operate. Test results for the gold and cyanide-copper systems are presented in order to demonstrate the high selectivity and effi­ciency of MRT technology in recovering these species from solution. . IBC Advanced Technologies, Inc. (IBC) and Fluor Daniel, Inc. formed a strategic alliance in late 1994. The goal of the alliance is to combine IBC's scientific expertise in the MRT field with Fluor Daniel's engineering capabilities in the metal­lurgical industry. IBC has its headquarters in American Fork, Utah, USA, where research, development and manufacturing are conducted. Fluor Daniel is an international engineering and construction firm with head offices in Irvine, California, USA. Engineering efforts for the alliance are centered in the Fluor Daniel Mining and Metals Operating Company office in Vancouver, B.C., Canada.

Jan 1, 1996

By Ronald J. Searle, Howard S. Latham

In April 1964 the Bureau of Reclamation awarded the first contract for rapid machine excavation of a water conveyance tunnel . Since then the Bureau has excavated seven tunnels with a total length of over 190,000 feet utilizing rapid excavation tunneling machines. Tunnel bored diameters have varied from 9' 0" to 20' 10" (See Table #1) and tunnel lengths from 5,000 feet to 67,000 feet. Driver and cutter units varied from 43 rolling teeth and eight rolling discs mounted on a rotating head driven by five 200 HP 23,000 volt electric motors to 20 discs and one tricone unit mounted on a rotating head driven by two 100 HP 440 volt motors. All tunnels were driven with a laser beam guidance system governing both line and grade. Trailing conveyors and rail haulage systems were used to dispose of the excavated material. Approved Bureau of Mines diesel locomotive engines for waste trains were prevalent power sources supplemented by battery units on some projects. Sandstone, conglomerates, agglomerates, siltstone, shale, and granite were the geological formations encountered, with sandstone and shale the preponderant material . Tunnel support systems utilized were structural steel ribs; rock bolts and metal plates; and shotcrete, or combinations of these. Progress varied from 51-1/2 feet to 154 feet per working day for three shifts, depending on rock material and supports required. One contractor established a record rate of advance of over 400 feet in one day, 1,905 feet in one week, and 6,848 feet in one month. Such diversified experience in underground machine excavation methods presented an excellent opportunity to observe, analyze, and evaluate associated environmental health problems. Also, to develop measures for controlling

Jan 1, 1997

By Sheldon P. Wimpfen

Man is a short time resident of the planet Earth. He does not have the memory to fully comprehend just what is going on. His span of knowledge can be related to the life of the world to see that this is the case. A museum at Grand Canyon features a geologic clock that compresses Earth's age of 4.5 billion years into 24 hours. Man's estimation of the earth's age has changed radically in the past half century. In 1930, one prominent geologist asserted that the age of the Earth was ". . . at least 600 million years." Later, physicists used radioactive clocks to conclude that the Earth's age was 1.6 billion years. More recently, geologists have found rocks in northwestern Australia estimated to have formed 4.5 billion years ago. As we learn more about what is underfoot, the estimate of Earth's age might change again. The Grand Canyon's 24 hour clock shows that the dinosaurs were the dominant life form for 165 million years. Then an event occurred that wiped them out about 65 million years ago. The prevailing theory is that an asteroid struck the Earth and generated enough dust to wipe out the vegetation upon which most dinosaurs fed. During Earth's existence, there have been at least 12 such mass extinctions - the worldwide disappearance of diverse animal groups. On a planet that has been around for 4.5 billion years and that may continue to exist for another 4.5 billion, it seems reasonable to expect that further mass extinction's will occur. According the Grand Canyon's 24hour clock, the 165 million year reign of the dinosaurs amounted to about five minutes. On that 24 hour clock, the world has been dinosaur free for almost two minutes.

Jan 1, 1993

By Edwin J. Connell, O&apos

Investment in mining and related process facilities will be more costly and complex in the 1980s than ever before. Interest rates and inflation are soaring; regulations are expanding; and in order to achieve economies of scale, plant facilities and mines are getting larger. As the pace quickens, the time/cost circuit closes around the resource owner or developer. Larger modern projects cost more money and take more time to build. The longer it takes to bring a project onstream, the more it costs in interest, escalation, and lost production. One solution to the time/cost squeeze is to take advantage of systems developed by major contractors serving the mining industry. These contractors have been serving clients in planning and executing large and small projects for many years. They have developed systems which, if applied at an early point in the project's life, can be a significant benefit in development of mineral resources. The systems involve performance of feasibility studies, economic evaluations, and the project installation itself. First the Feasibility Study Feasibility studies can minimize risk through systematic evaluations while progressing toward the ultimate objective-an operating plant. Normally, studies are initiated with a minimum amount of specific information and a maximum number of as¬sumptions. Through the course of the study program, assumptions are continuously confirmed, refined, or rejected by facts until a sound basis for decision is available. High on the list of cost effective tools for evaluation is the use of a geostatistically derived sampling program that provides a highly accurate ore reserve estimate for economic evaluation. When a predetermined sample of data from the drilling program and bench-scale or pilot-plant tests are received, a detailed feasibility study may be started. This study can involve design of the mine,

Jan 10, 1980

By Gordon C. ‘Bud’ Presley

The pumice and pumicite review arrived too late for the June issue. Estimated domestic production of pumice and pumicite in 1992 was up compared with 1991, according to US Bureau of Mines statistics. The Bureau estimate of domestic production of 400 kt (440,000 st) for 1991 turned out to be 401 kt (442,000 st) of actual production, the lowest since 1989. In 1992, the estimated the value of pumice and pumicite sold or used in the United States was $11.6 million, up only $200,000 from the 1991 value. There was an increase in the mine, or mill, average price from the five-year low of $11.44/t ($10.37/st) in 1986 to $26.42/t ($23.96/st) in 1992. Estimated tonnage produced in 1992 was 439 kt (484,000 st). Apparent domestic consumption was 642 kt (707,000 st), up 135 kt (149,000 st) from 1991. Imports for consumption were estimated to be 215 kt (237,000 st) last year. Domestic production supplied 68% of the demand in 1992, with net imports supplying the remaining 32%. This compares with domestic production sup¬plying 53% and net imports supplying 47% of the apparent consumption in 1988. Exports were about 900 t/a (1000 stpy) for the period 1984 to 1988. In 1989, exports rose sevenfold to 7 kt (7700 st) and to 20 kt (22,000 st) in 1990. The Bureau of Mines reported that the amount of pumice and pumicite exported in 1992 was 12 kt (13,200 st). It is assumed that these exports were from the Pacific Coast because imports, mainly from Greece, continued to be a market factor on the East Coast and the Gulf Coast States in the United States.

Jan 1, 1993

By A. Fiszer

One of the major problems with deep Polish hard coal mines are deformations of close-to-wall galleries since they are necessary and must he kept open for emergency situations and are largely responsible for work disturbances. In order to ensure safe and effective working operations, it is necessary to often rebuild galleries which, apart from the inevitable stoppage of operations, is greatly disadvantageous for the operation of a mine. The largest problems with maintaining the galleries open occur in Lower Silesian Coal Field mines where sometimes it is necessary to reconstruct the galleries several times [(Fig. 1)]. In light of what has been said above, the aim of this article is to present the reader with methods and ways of determining deformations occurring in close-to-wall galleries. Squeezing or convergence of headings is only a portion of the entire process of ground movement caused by ground disturbance due to workings. The term "squeezing of headings" is to be understood as a shortening of the distance between a point set on the roof of a heading and the corresponding one on the floor. It is very important to know the rules governing the process of squeezing in a particular mining system since it affords possibilities to define changes of the process and its parameters at any moment for a given system. This is of utmost importance because convergence of a heading is one of the most significant manifestations of ground pressure which has already been proved by studies performed by Everling (1). On the basis of those studies it has been observed that there exists an almost linear relation between the rate of convergence and loading [(Fig. 2)]. This, in turn, means that the deformations of the already exploited portion of heading are proportional to the pressure changes.

Jan 1, 1982

By Gary F. Rajala, Bruce R. Greenwood

INTRODUCTION The Empire Mine is an iron ore mining, concentrating and pelletizing facility operated by The Cleveland-Cliffs Iron Company in the Upper Peninsula of Michigan. Owners of the mine are Inland Steel, LTV Steel, Wheeling-Pittsburgh Steel and Cleveland-Cliff s. The orebody is a fine-grained, low grade iron formation with magnetite as the primary constituent. Also present are iron carbonates, iron silicates, chert, hematite, goethite and quartz. The original six concentrating lines were started in late 1963. Successive expansions of ten lines in 1967, five lines in 1974 and 3 lines in 1979 have resulted in Empire reaching a present annual capacity of 8.0 million long tons of pellets. The Empire flowsheet was developed over several years of laboratory bench testing, pilot plant testing and testing of a full-scale primary autogenous grinding circuit. Since the original flowsheet was established, modifications have been made based on pilot plant and full-scale plant tests. The present flowsheet for three sections of the concentrator consists of one stage of crushing, two stages of closed circuit autogenous grinding, two stages of magnetic separation, one stage of hydraulic concentration and two stages of flotation (rougher and scavenger). The flowsheet for the fourth section of the concentrator (Empire 4) is the same as the first three sections, except a crusher has been added to crush excess pebbles. The Empire 4 flowsheet appears in the at- tached figure. PRIMARY GRINDING CIRCUIT FLOWSHEET Empire has a total of 24 individual grinding lines. However, at the present time, Line 1 is not being used for processing crude ore. The primary mill on Line 1 is now grinding flux stone for fluxed pellet production and the secondary mill is being used as a ball mill to grind rougher flotation tailings prior to a scavenger flotation circuit.

Jan 1, 1992

By Victor J. Scaravilli

This report is based on experience developed on the construction of one contract for the Buffalo, New York subway. The Buffalo subway is under construction for the Niagara Frontier Transportation Authority and is called the LRRT-Light Rail Rapid Transit or more commonly the Metro. The Initial Route of the Buffalo subway construction started early in 1979 and is scheduled for completion in May, 1984. The initial system includes 5.2 miles of underground construction, 1.3 miles at grade for a total of 6.5 miles of subway system. A total of fourteen stations, eight underground and six at grade are included on the system. The Initial Route has a planned expansion to 17.3 miles in the future. On January 15, 1979, a Joint Venture of S & M Constructors, Inc., Solon, Ohio, James McHugh Construction Co., Chicago, Illinois, and Kenny Construction Company, Wheeling, Illinois, was awarded contract 100031, the Line Tunnels from Amherst Street to South Campus in northcentral Buffalo between Delaware Park and the State University, (see Fig. 1, Location Plan) This $35,000,000.00 contract was designed by Hatch Associates Consultants, Inc., Buffalo, N.Y. The Notice to Proceed was issued January 15, 1979 and the scheduled completion date is August 18, 1981. The project consists of two parallel rock tunnels with a minimum excavated diam of 18 ft 0 in. and a final concrete lining of 16 ft 0 in. diam. The tunnels total 14,630 linear ft. In addition to the tunnels, contract C-31 includes four shafts, an underground pump station, three cross passage connections, and other minor work items. (see Fig. 2, C-31 Project Plan and Profile) The tunnels were constructed primarily within the Bertie Formation, an approximately 50 foot thick moderately fractured to massive, dolo-

Jan 1, 1981

By Eugene A. Lang, William R. Archibald

Early in 1972, Rocky Mountain Energy Company approached MARCONAFLO with a unique request for assistance. They controlled a series of scattered ore deposits in a remote section of Wyoming which had become increasingly valuable despite their relatively small size, great depth and low grade. At the time, MARCONAFLO was in the process of developing a tailings reclaim system which was based on the use of submersible capsules. It appeared that this basic concept might be adapted to slurry uranium ores and pump them to the surface through a bored hole. This presentation will review for you the development of this unique and potentially very important application of MARCONAFLO technology. This first slide (SLIDE 1) depicts the total mining concept envisioned by MARCONAFLO and Rocky Mountain Energy Company. A series of six self-contained mining units would be positioned through boreholes into the ore strata. An oscillating MARCONAJET would direct a high pressure jet stream into the orebody and put it into a slurry which would flow back to a slurry pump. The slurry would then be pumped to the surface and to a collection tank from which it would be transferred to processing. Both the MARCONAJET and the slurry pump would be actuated and controlled by means of a hydraulic power console mounted on the trailer behind the service tower. By means of a high pressure water pump also mounted on the trailer, return water from processing would be delivered to the MARCONAJET to slurry the ore. Tailings would be returned to a backfill unit for redepositing in the mined-out cavities. A drill rig would precede the mining, and it was estimated that this configuration would represent an optimum system for most effective equipment utilization.

Jan 1, 1976

By Andrew B. Cecala, Robert J. Timko, Christopher J. Pritchard

As mine venti1ation systems become more complex, it is increasingly difficult to supply fresh air to the working face. A high percentage of the fresh air entering a mine never reaches the working face because it short circuits through stoppings and doors, exiting the mine without being utilized. When ventilation limits are reached, the only option presently available to most U.S. mines is to sink a new shaft - an extremely expensive undertaking that many companies cannot afford. Reusing or recirculating a percentage of ventilating airflow may make it possible for some mines to remain operational while maintaining a safe environment for workers. Such a study was performed at a trona mine in Granger. Wyoming. A vane axial fan was used to recirculate approximately 9.4 m /s (20,000 cfm), 25% of the total ventilating airflow, back to the working face area of a three-entry continuous miner section. This study involved two evaluations: the first when the face was 305m (1,000 ft) from the recirculation fan, the second when the face was 610m (2,000 ft) from the fan. The evaluation consisted of monitoring the mine atmosphere for respirable dust, methane (CH4). carbon monoxide (CO), and nitric oxide (NO), at various locations in the intake and return entries. Several shifts were monitored, with and without the recirculation system in operation. With the recirculation system in operation. there was an increase in measured respirable dust concentrations in the intake along with a slight increase in the mine temperature (1.67°C). There were also some minor changes in CO and NO levels in the intake entry, but this seemed to depend on the proximity of the instruments to the turn-around point for the diesel haulage vehicles, than to whether the recirculation system was or was not in use.

Jan 1, 1989

By Giovanni Toniatti

Brazil is a country with continental dimensions. It hosts many different varieties of terranes and geological environments in its 8.5 million km2 (3.28 million sq miles). This mineral endowment has been important for the country's economic and social development process since the early colonial period, leaving Brazil with a legacy of almost 400 years of mining tradition. Mining in Brazil started in the early 17th century with diamond and gold discoveries. The made the country the leading producer of both for more than a century. This phase faded by the late 18th century when the alluvial deposits were depleted. It finally yielded to competing countries where technology and capital were being applied more efficiently. This period of mining dormancy lasted from the late 19th century until the first decades of the 20th century when Brazilian mining picked up. There was growing pressure on mineral resources by the affluence of the industrial society. The fast-growing demand resulting from the two world wars had brought the Brazilian mineral wealth back to the scene. This second Brazilian mineral boom made the country a leading producer of iron and manganese ore, quartz crystals and other strategic minerals. This expansion in Brazil's mining industry provided the basis for the country's industrialization process. This was led by the Brazilian steel and petroleum industries. Unfortunately, the thrust provided by this modern industrial basis was not properly used as a lever for further industrial development. The upstream industrialization process was not supported by the proper development of the raw materials supplying basis. The resulting industrial model was heavily dependent on imports of raw materials. It did not support the economic growth and faced fierce industrial competitiveness and sophistication that emerged with the postwar economic boom.

Jan 1, 1997

By P. Hambach

Murer Company, Andermatt, Switzerland, can claim to have done pioneer work in the construction of inclined shafts. This happened in 1968/69, when we decided to bore with a Wirth tunnel borer an inclined shaft, 1100 m in length, 3.0 m in diameter, and with a grade of 65%, in the 2400 kilo pascall per sq. cm granite of the Montblanc Massive. The whole excavation was accomplished in ten months which, at least for European conditions, can be claimed as a record. It was, at least to our knowledge, the first inclined shaft to be bored full-face (Fig. 1). Encouraged by the experiences and performances attained at Châtelard, we approached other projects of the same kind. We were awarded, together with Hochtief Ltd., Essen, a contract from Schluchseewerke, Freiburg, Germany, in December 1969, for the construction of a penstock for the Hornbergstufe at Wehr, Germany, with a diameter of 6.3 m. This inclined shaft with a grade of 55% is located in Schwarzwalder granite with a compressive strength of up to 2000 kilo pascall per sq. cm, about 31,000 psi. As no exact geological data were available about the rock to be worked, and a fault zone from 80 to 150 m long had to be faced, as well as a few individual fissures of varying thickness, it was decided to use the multi-stage method. The 3-m diam tunnelling machine which had driven the oblique shaft at Châtelard had now finished work, and an immediate beginning was made with driving the pilot staft. This was very welcome to the contractor, since exact information about the type of rock present and the inflows of water was required immediately and before the final borehole diameter was fixed, for the purpose of dimensioning the supports to be subsequently installed.

Jan 1, 1974

By Robin J. Hickson

The Grasberg copper-gold deposit was discovered in the spring of 1988, one year before the planned closure of Freeport Indonesia's original Ertsberg openpit copper mine. In spite of Grasberg's remote location, 600 m (1968 ft) above the Ertsberg, atop a hitherto inaccessible mountain, Freeport-McMoRan brought its latest open-pit mine into production in the last week of 1989, less than two years after discovery. Freeport Indonesia's (FI) copper-gold mining operations are located in Irian Jaya, the easternmost province of Indonesia on the western side of the island of New Guinea. Fl's six ore deposits are all located within a 10- x 10-km' (3.9- x 3.9-sq mile) Contract of Work area. They are all between the elevations of 2900 and 4300 m (9515 and 14,100 ft) above sea level, some 96 km (60 miles) from the island's southern coast. A 118-km (74-mile) access route connects FT's port site of Amamapare on the Arafura Sea to the project area. The first section is an 18-km (11-mile) barge waterway. The final 100-km (63mile) is a two-lane gravel highway. The highway terminates 9 km (5.5 miles) beyond the FI townsite at the project's central mill, some 2850 m (9250 ft) above sea level. The mining areas are separated from the mill by a 780-m (2560-ft) sheer cliff face. The world's longest free span tramway system, with a total length of more than 1.6 km (1 mile), is the only means of access for men and materials between the mill and the surface mines. Weight restrictions for the tramway for equipment considered for the project are 15.4 t (17 st). The minimum clear width dimension of two tunnels along the portsite access road is 5.6 m (18.4 ft).

Jan 1, 1991

By Shinya Ono, Tsuyoshi Katoh, Yuusaku Tominaga

In order to monitor/control airflow rate distribution in a complicated ventilation network installed many regulators, an integrated system composed of expert system, exerting programs for simulation to get macroscopic characteristics and drawing diagram, monitoring system and so on is introduced in this study. This system is made up of airflow velocity sensors and computers linked to an local area network. The main results of this study are as follows; 1) Combinations of two branches to monitor aerodynamic resistance change in a branch p in a network can be selected by comparing factor's value in a branch relation table. 2) When the combination of sensor branches for a branch p does not exist in the network at present condition, the system changes aero- dynamic resistances of appropriate branch q placed a regulator by referring branch relation table. And then the system asks other computer to get macroscopic characteristics under altered value of aerodynamic resistance of the branch q. 3) Dot pattern diagram shows airflow rate relation between an active branch and a passive branch. Three relations such as a) a straight line, b) a monotonous curve and c) extremums are displayed in different patterns for all the sets between an active branch and a passive branch at a time. 4) The ranges of airflow rate in coal faces by changing aerodynamic resistance of any one branch placed a regulator are shown in the Pareto diagram using values in the branch relation table. 5) Ventilation transfer diagram with two parameter, one shows airflow rate in a coal face and the other shows energy provided by main fans to overcome aerodynamic resistance in a net- work, is utilized to decide countermeasures for decreasing energy consumption in the network on increasing of airflow rate in the specified branch.

Jan 1, 1995

In April 2012, work started on one of the most ambitious construction projects of Austria?s ÖBB-Infrastruktur AG ? the New Semmering Base Tunnel. Scheduled for completion in 2024, the 27.3 km (17 mile) tunnel through the Semmering range will cut the journey time on the south railway connecting Lower Austria and Styria. Before con-struction can begin at the entrance portal and tunnel bores, the work concentrates on the above ground sections with the clearance and excavation of the entrance ramp site. The slope is currently being excavated by the Baubeteiligungsge-sellschaft m.b.H. BBG-GRAZ. The cut face is shored up with shotcrete and permanent self-drilling anchors produced by Minova MAI, an economical bolting solution for softer rock formations. After completing the surface construction work, the twin-bore, single-track tunnel will be cut through the Semmering by conventional and continuous excavation beginning in 2015. Once completed, the New Semmering Base Tunnel will be one of the longest rail tunnels in Austria. It will act as a vital link on the route crossing Europe?s heartland from Northern Germany to Italy, which currently has to climb the steep Semmering pass between Gloggnitz and Mürzzuschlag on a historic mountain railway recognized as one of the UNESCO World Heritage sites. The old route imposes considerable limitations on heavy freight trans-port, and passenger trains have to slow down to a speed of around 50 kph (31 mph). The New Semmering Base Tunnel will bypass this bottleneck and cut 30 minutes off the journey time between Vienna and Graz. It represents a particular advantage for freight traffic, since the new route?s minimal incline of 8.4 percent removes all obstacles for even heavy freight trains.

Jan 1, 2013

By Thomas V. Mullen

Some 146 kt (4.69 billion oz) of gold have been mined throughout history. Of this, 70% has been mined in this century alone, with 17% produced from 1985 through 1996 (Fig. 1 and Table 1). Until the mid-19th century, placers were the chief source of gold. Advancements in mining, metallurgy and geological thinking have resulted in underground mining (first of veins plus stockworks and later of Rand-type deposits) becoming the principal source of gold. With the demise of the South African deposits and the move towards lower grade ores, the primary source of gold will be from disseminated deposits exploited through large, open-pit mines. For the past 200 years, there has been a fairly constant ratio of about 31 g (1 oz) of gold to each person alive. If this ratio is to be maintained, annual gold production will have to rise from about 2.3 kt/a (73.9 million oz/year) to more than 3.1 kt/a (99.7 million oz/year) by the year 2000. To effect this increase, an unforeseen breakthrough in exploration or metallurgy is needed. Barring this, there will be pressure for an increase in the price of gold. This article traces the historical production of gold from 4000 B.C. - the earliest record of gold mining - to today and relates this 6,000-year record to advances in geological thinking, mining engineering and extractive metallurgy. It also proposes that man's thirst for gold, reflected in the price he will pay for gold, and his ability to find, mine and refine gold have combined to effect an equilibrium based loosely on the historical ratio of 31 g (1 oz) of cumulative gold production per each man or woman alive.

Jan 1, 1998

By L. A. Puchkov

Problems of how to use artificial intelligence (AI) methods and expert systems (ES) to control complex industrial projects have lately become significant in practical terms. Mining ventilation systems undoubtedly belong to complex multi dimensional objects of control with stochastic nonstationary and nonlinear processes. Formal models based on automated ventilation control, do require awkward algorithmic solutions, moreover, a number of tasks become the operator's headache, and the quality of their solution depends on his experience and intuition. These tasks include: - identifying pre-accidental situations and determining their causes; - making well-grounded decisions with regard to changing ventilation regimes, forecast of mining operations taken account of; - controlling ventilation systems in emergency situations, e.g. when in accident, etc. It is in this context that we have for a number of years been investigating how to practically use AI methods for operative control in dynamic aero-and-gas mining processes, one of our research directions being devoted to working out a consulting programme for the ventilation system operator. Our researching and modeling problem was identification of aero-and-gas situation in different parts of ventilation network and its interpretation in order to determine possible causes for gas regime changing and unexpected consequences. We would single out the following stages in this task: I. Operative information procession coming to the data base from the sensors and analysis of hypothetical versions (using the associative rules base) with regard to factors which have caused significant parameter fluctuations (e.g. C%(t), H(t), Q(t) etc.)., 2. Selection of hypotheses in the knowledge base and forming conclusions in accordance with reliability scale. 3. Clarifying the obtained conclusions in dialogue with the operator. 4. Correcting the associative rules base.

Jan 1, 1992

By Anna Marabini

This paper provides a summary of the studies performed over a period of more than fifteen years by the Italian National Research Council's Mineral Processing Institute in Rome to develop applications for the use of chelating reagents in the flotation of metallic minerals. A description is given of the various phases through which the studied progressed, starting with the combined use of commercial chelating reagents and a neutral oil and then moving on to the synthesis of new long-chain chelate collectors for the flotation of sulphide and oxidized Pb, Zn and Cu minerals. After a series of preliminary tests which confirmed the possibility of floating various metallic minerals with commercial reagents containing chelating groups exerting specific action on given cations, the studies were addressed to the development of a theoretical method of choosing chelating groups that exert selective action on one metallic mineral rather than others. The theoretical approach was based on thermodynamic data concerning the chemical equilibria in solution. The validity of the method has been proved in numerous cases by flotation tests on pure minerals. Subsequently the research was directed towards the design and synthesis of reagents with a mixed aliphatic-aromatic structure containing chelating groups for Pb and Zn and an alcoxyl chain of various length, position and configuration. The flotation results obtained on oxidized and mixed Zn-Pb ores provided interesting pointers for designing the nonpolar portion. The structural criteria identified via these studies were interpreted on the basis of chemical and steric considerations. A description is given of a new synthetic chelate collector which is effective in the selective flotation of Cu minerals from complex sulphides. The fact that this reagents is more selective than xanthate is demonstrated by comparative flotation tests on actual ores.

Jan 1, 1994