Search Documents

By Barton Kelby Cross

In the early 1960's the feasibility of mathematical modeling was demonstrated in Northern Rhodesia and southwestern United States, where techniques were developed to use these models in a new approach to aid engineers in the estimation of ore reserves, mine designs, and financial evaluations. These rudimentary models closely followed the manual methods, producing ore reserves and production schedule estimates that were as accurate as the manual methods, yet were many times faster. Mines evaluated and designed using these new tools gradually came into operation during the 1970's and entered the phase at which production scheduling and ore-grade control became day-to-day problems. Management expected the number of operational engineers to be small because small planning engineering staffs had produced the original designs and operated the smaller high-grade pits. Unfortunately, the tools needed by the mine engineer to perform short-term production scheduling and ore-grade control were labor intensive; they had not yet been generally computerized. Several attempts to use the original or exploration model for these two functions were futile. While an exploration model based on data from exploration work proved sufficiently precise for overall mine design and long-term production scheduling, the model lacked the precision required for short-term scheduling and grade control.

Jan 1, 1979

By T. J. Driscoll

The effect of coatings on the incendive properties of aluminum alloy 6061-T651 in air-6.4%CH4 was studied for collisions between rusted steel and both uncoated and coated projectiles with incident energies as high as 300 J (220 ft-lb) and velocities as high as 200 m/s (660 fps). These conditions were intended to simulate the rough handling of equipment in coal mines. The ignition probability using uncoated alloy projectiles increased with increasing relative humidity and appeared to be influenced by atmospheric ozone content. The incendive properties of both the uncoated and coated alloy depended on the type of rust used, but the dependence of the coated alloy was very different from that of the uncoated alloy. A number of coatings developed in the last 25 years were found to offer protection from ignition and to remain largely intact for occasional collisions or collisions randomly distributed over the coating surface, but probably not for repetitive collisions at any given point on the coating. These protective coatings utilize a hard anodized aluminum alloy surface coated with one or more layers followed by heat treatment of the coating. Coatings containing Teflon and MoS2 and thicker than 50 µm (2 mils) appear to be most effective.

Jan 1, 1987

By Terry Owen

Business development process. Throughout Cyprus Amax's early months in Russia, the company stayed focused on what was needed from a deposit for economic success. Cyprus Amax's reason for success in Russia is that all involved - its Russian partners, the workforce and expatriates - provided a focused effort that served the project as it worked through the tender process and the Russian regulations. The company developed an understanding of the regulatory process by working with solid, ethical partners. Infused into the Kubaka management structure were Russians with the knowledge to facilitate the process and a professional group of expatriates. Developing credibility and a solid rapport with the Russian mining authority was critical to the success of this venture. Identifying and gaining the trust of key Russian individuals was also critical during the early stages. Gaining their trust and building credibility was part of the process. These key Russians were brought to the United States to visit existing Cyprus Amax mines. These efforts proved valuable in building an understanding with the Russians about the kind of company Cyprus Amax is and the kind of efficient operations that it can run. This was a learning process for all parties. Fortunately, the company was dealing with intelligent and educated people.

Jan 1, 1997

By S. Chander

The use of various electrochemical techniques to study mechanisms of sulfide mineral- flotation reagent interactions is briefly reviewed in this paper. Prior to such studies it is desirable to thermodynamically determine solution conditions favorable for formation of hydrophobic species deemed to be responsible for flotation. The thermodynamic equilibrium involving both the stable and metastable species can be conveniently represented by an Eh-pH diagram. Thermodynamics can also be used to predict conditions where a mineral might not float if depressants are present. Under favorable conditions of flotation there is competition between reactions leading to formation of hydrophobic species with reactions that lead to formation of hydrophilic species. Due to the sluggish nature of the reactions involving sulfide minerals, a knowledge of the kinetic behavior of the system is necessary. Electrochemical methods of investigation are wed in laboratory studies to (1) control the state of oxidation, (2) determine the type and amount of electroactive species present at the mineral surface, and (3) study kinetics of electrode processes. By combining electrochemical techniques and wetting measurements the identification of hydrophobic species that might be present at the mineral surface could be achieved. Both contact angle measurements at mineral electrodes or flotation in a cell equipped with a particulate bed electrode can be used for the wetting measurements.

Jan 1, 1987

By Al. Valero, A. Domínguez

This paper appraises the energy requirements for mineral production through an exergy approach taking into account the long-term decline in ore grades. In this context, the exergy required for restoring resources from the dispersed state of the so called Crepuscular Earth into the physical and chemical conditions in which it was delivered by the ecosystems in light of the available technology, is known as exergy cost. The exergy cost is the point of reference in order to evaluate in a single variable, characteristics such as composition, concentration (ore grade) and the state of technology. The ratio between the exergy cost and the minimum thermodynamic cost required to accomplish the same process is called unit exergy cost and provides a measure of the irreversibility of the analyzed processes. Otherwise, the ore grade is one of the main issues which affects directly the costs associated with mining the ore. Hence, the unit exergy costs to produce minerals from progressively lower ores grades by the current technology is analyzed. The unit exergy cost curves are presented for some important minerals such as aluminium, chromium, cobalt, copper, gold, lead, manganese, nickel and zinc, in order to know the trend when the ore grade decreases.

Jan 1, 2011

By J. Ramirez-Castro

The abstract and text of this chapter were not received in time for printing.

Jan 1, 1982

By M. A. Sochocky

Rod mills were developed, as a logical substitute for the rolls crusher when larger tonnages had to be handled, on a continuous basis. Today, with even larger tonnages to process, the trend is to install larger equipment, automate the plant and develop the highest availability possible, in order to cut costs. The rod mills, because of design limitations in size and speed 1'2, are not able to meet these new requirements. The autogenous mill was a timely development and serves as an excellent alternative for ores that are suitable to this type of grinding. When ores are not amenable to autogenous grinding, selection of a flowsheet is dictated by liberation characteristics and unit operations to be used for mineral recovery.. The following alternatives are available: (a) Multiple rod mills, capable of drawing no more than 2000 HP each, followed by ball mills. (b) Gyradisc crusher followed by two stages of ball mill grinding.3 (c) Tertiary crushing followed by closed circuit single stage ball mills grinding to approximately -100 mesh, as in the copper industry. (d) Tertiary' crushing followed by two-stage, ball milling. Each stage will operate in closed circuit with either screens or cyclones. It is this last alternative, particularly as it

Jan 1, 1972

By R. B. Steele

The paper contains the results of the physical and mathematical simulations (based on the finite elements simulation) of the length and shape influence on the mechanical strength of the brex. Key words: Stiff extrusion, extruded briquettes, BREX, mechanical strength, cold strength, compressive strength, tensile splitting strength, oval shape, finite elements simulation. INTRODUCTION Extruded briquettes (BREX) exhibit a set of unique properties when compared with briquettes formed by alternative methods. Brex generally have sufficient integrity right after extrusion to withstand the necessary handling and stockpiling and does not require any special means and tools for the green briquettes strength conservation. In a typical die without an ancillary cutting device green brex tend to have very high length to diameter (L/D) or length to section area ratios. For round hole dies the brex are typically 5to 6 times the diameters and even longer. Stiff-extrusion allows also for the very easy changing of the forming dies. Dies with different cross-sectional shapes of the brex (round, ovals, square, hollow structures and many other two dimensional shapes) are possible, and common. The results of our investigations show how these geometrical shape factors contribute to overall quality of the brex both in terms of strength and as new charge components in metallurgical furnaces and processes [2-4]

Feb 27, 2013

By Hubert E. Sherer

The mining industry is presently one of the most heavily capitalized industries in the U.S. (U.S. - Statistical Abstracts, 1979). U.S. sales of new mining equipment (not including environmental, preparation, or long distance transportation equipment) are projected to reach approximately $5 billion/year in 1980 (Frost and Sullivan, 1979). Of these new equipment sales approximately 30 to 40 percent of this equipment will be used to replace old equipment. Therefore, an increase of efficiency in the use of equipment replacement capital could have substantially positive effects for the U.S. mining industry. This is very critical in these times of restricted capital availability, double digit inflation, burdensome governmental regulation, and rising foreign competition in the mining industry. This paper examines the numerous factors that constitute the typical mine equipment replacement problem. A computerized, mathematical model is formulated to utilize historic cost and production information to predict equipment cost versus age for the existing and potential replacement machines. Another part of this computerized model determines the best equipment replacement strategy that accomplishes estimated production goals at a minimum discounted cost. This computerized model is an easily used, consistent method of determining the optimum replacement age for any equipment unit or fleet of equipment at a mining operation.

Jan 1, 1982

For nearly two decades, MINExpo International has held the title to the biggest show in mining. The 2012 MINExpo is expected to be the biggest yet, with nearly 1,800 exhibitors rolling out the newest equipment and services across 12 halls. From September 24 to 26 in the Las Vegas Convention Center, MINExpo will present the newest in everything from automation and robotics to safety and communications equipment to reclamation services, and much, much more. The last MINExpo, in 2008, had nearly 38,500 visitors. The show?s sponsor, the National Mining Association, expects this year will be even bigger, with more than 40,000 visitors over three days. Twenty talks on the issues facing mining today are scheduled for Tuesday and Wednesday mornings, but the real action will happen out on the floor. That?s where ultra haul trucks big enough to carry as much as 363 t (400 st) of rock will be assembled next to underground loaders able to lift more than 20 t (22 st) in one scoop. Caterpillar, Komatsu, Liebherr, Sandvik, Atlas Copco: all the big names in mining equipment will be there. Their massive earthmoving equipment and mining machines are the centerpiece of the show. Preassembly for the largest pieces begins on August 6, 2012.

Jan 1, 2013

By P. van der Veen

The objective of this paper is to analyze the evolution of the strategic drivers of the mining sec-tor over the last half century, which has been guided by a varying and expanding list of motivations. While companies cannot survive for long unless they are making profits, the strategic drivers of the industry have gone far beyond profits since at least the mid-1970s when environmental concerns began to be taken seriously. For the most part, these forces have followed global trends and public opinion, but they have been shaped and magnified by the significant, often dominant role that the mining sector plays in many economies. While the mining sector used to be primarily motivated by the first pillar of sustainable development -i.e. the economics pillar-, in the 1970s the second environmental pillar became an important factor in decision making, and in the 1990s the third social pillar emerged as a major driver.1 The entrance of new strategic drivers has also had considerable impact on technological and organizational developments in the mining industry; however, technological changes, driven by cost reduction considerations, have in turn impacted the strategic drivers of the industry, resulting in the need for further technological and organizational developments.

Jan 1, 2007

By J. M. Wempen

Booster fans, large underground fans, can increase the volumetric efficiency of ventilation systems by helping to balance the pressure and quantity distribution throughout a mine, reducing leakage and reducing the total power requirement. However, in ventilation systems that use booster fans there is a potential for system recirculation, the leakage of return air to intake air, and also for localized recirculation near the fan through the bulkhead and airlock doors. Air that is recirculated locally decreases the system efficiency because the quantity of air flow through the fan increases without increasing the airflow throughout the system. To understand the detailed flow characteristics of a ventilation system with a booster fan, two-dimensional computational fluid dynamics (CFD) models were developed using the software Ansys-FLUENT. Though two-dimensional models do not represent the full complexity of the flow dynamics, they do provide a good representation of the flow characteristics and they allow for a qualitative analysis of how the flow dynamics are affected by the system characteristics. The CFD models were used to evaluate how the number of booster fans, the booster fan placement, the location and geometry of the fan installation and the construction of the airlock system affect the flow characteristics and the localized efficiency of the ventilation system.

Feb 27, 2013

The title of “the world’s biggest volume-produced hydraulic breaker,” that was held for more than a decade by the Atlas HB 7,000, changed hands with the launch of Atlas Copco’s HB 10,000 at bauma 2007. A service weight of 10 t (11 st) and up to 50 percent higher productivity represent major steps toward a new market segment: the use of hydraulic breakers as cost-efficient production machines for primary breaking and as a true alternative to drilling and blasting. The HB 10,000 has all the technical features developed by Atlas Copco for its hydraulic breakers and includes: StartSelect — the breaker’s start-up and shut-down behavior can be adapted to the conditions. AutoControl that ensures an optimized balance of impact energy and impact frequency to maximize percussive performance. Auto-Control also reduces blank firing force and controls energy recovery. PowerAdapt — if oil pressure is too high, the breaker shuts down automatically. This prevents downtime and is particularly useful when breakers are used on different carriers. DustProtector II — a combination of multiple strippers prevents abrasive rock dust and foreign bodies from penetrating the lower breaker section. Conti- Lube II — the automatic lubrication unit guarantees optimal lubrication of the breaker at all times.

Jan 1, 2007

By P. Christmann

"In June or July 2005, the European Commission will present its Thematic Strategy on the Sustainable Use of Natural Resources proposal to the Council and European Parliament, one of the seven Thematic Strategies to be developed and implemented under the 6th European Environment Action Programme in support of the European Union’s Sustainable Development Strategy defined by the European Union’s Head of State at the Göteborg European Council, in June 2001. The time scale for this Thematic Strategy is 25 years (2005-2030). This paper discusses some of the key issues related to the EU minerals and metals industry that needs to be addressed by the Strategy. These are: - the need for access to mineral reserves in the EU and abroad; - the need to strenghten the capacity of developing countries to sustainably promote and regulate the use of their mineral potential; - the need for an EU mineral resources intelligence capacity. There are additional important needs, which are not discussed in this paper, such as: - the need to foster further innovation in mining, ore beneficiation and metallurgical technologies; - the need to integrate and simplify the exisitng complex regulatory framework applicable to the EU mining industry and to effectively implement existing legislation."

Jan 1, 2005

By R. J. Boyd

SUMMARY The productivity of drill and blast methods of mining in hard rock is limited by the cyclic nature of the operation, and a plateau of performance has been reached, even with the most advanced equipment developments. Higher mine operating costs and lower metal prices have more than ever generated the need for breaking through these productivity barriers. After initial field testing The Robbins Company has designed and manufactured, on a joint venture basis with Mount Isa Mines, Ltd., Australia, a prototype "Mobile Miner" for continuous cutting of hard rock. This paper describes the cutting concept, the initial application of a completed 1,156 m (3792 ft.) long 14% decline, actual performance and delay analysis, developmental modifications, anticipated performances of a fully developed machine, and possible future applications. Sincere appreciation is expressed to the management of Mount Isa Mines, Ltd., for allowing access to the data used in this paper. The views expressed here are those of the author and not necessarily those of Mount Isa Mines, Ltd. INTRODUCTION A paper titled, "Design and Development of a Mobile Mining Machine", was presented by J.P. Kindsvater at the RETC, New York, in 1985. This paper described the evaluation of a test fixture in an andesite quarry near Seattle, followed by design, construction and

Jan 1, 1987

By M. Bennett, L. Twidwell

Montana Tech has embarked on a coordinated series of studies to delineate the characteristics of the Berkeley Pitlake containing over 36 billion gallons of acidic, metal-contaminated water formed after the cessation of open-pit copper mining in Butte, Montana, USA. The objectives of the overall series of studies are to summarize presently available information and to generate new and needed information to formulate a conceptual environmental model for the pitlake and to provide characterization data for the development of advanced treatment technologies. In this presentation, the chemistry of the Berkeley Pitlake water is partially reviewed. It is known that the pitlake consists of two distinct layers of water referred to as surface and deep water. Samples of deep water were collected and placed in a 12-ft high and 6-inch diameter column and exposed to different wavelengths of UV radiation as well as atmospheric conditions. Measurements of pH, redox potential (EH), dissolved O2, turbidity, conductivity, temperature, and elemental composition show that the water reacts differently and indicates that the diurnal effects of sunlight likely play a major non-biological role in its chemistry. Resulting technology could be useful for developing an alternative to treating acid-rock drainage.

Jan 1, 2007

Your assessment of the minerals business. I would first like to express our profound sadness and sincere condolences to the families of the miners who lost their lives in recent mine mishaps particularly in West Virginia, and other locations. Any loss is unacceptable. It is time to review and, if required, re-establish a rigorous health and safety agenda in the mines. It must involve a review of health and safety regulations. And innovative training methods for sensing, awareness and mitigation of health and safety hazards must be developed. As far as the minerals business is concerned, I am excited about the outlook for mining. Over the last 20 years, global demand for minerals has closely mirrored the growth of the gross domestic product. Minerals re-main a major part of the world’s economic foundation. And that will continue to be the case. It is no surprise that the fortunes of the mining industry rise and fall with general economic trends. Globally, mining has been strong — thanks to the explosive economic growth in Asia. The U.S. mining industry has performed reasonably well, with notable strength in the metals, coal and construction and aggregate areas and with some softness in the industrial minerals sector.

Jan 1, 2006

By D. L. Ogonowski, J. O. Marsden

The Candelaria copper-gold mine is located approximately 25 km south and east of Copiapo in Region III, Chile. The original concentrator was designed to treat 28,000 t/d (30,800 stpd) of chalcopyrite-bearing ore through a circuit consisting of a single 11.0 m(36 ft) diameter SAG mill, two ball mills, conventional rougher and scavenger flotation, column cell cleaner flotation, and ceramic disc filtration. The plant was commissioned in August 1994 and quickly reached design capacity and expected levels of metallurgical performance. In May 1996, a decision was made to double the capacity of the concentrator by the addition of a second line of equipment. The expanded facilities were commissioned in October 1997, less than 18 months after the decision to proceed, and well within the budget. The original concentrator facilities were replicated or duplicated as much as possible, however, a number of important equipment changes were made to take advantage of industry developments since the original concentrator was designed. These included the use of Eimco 120 m3 (4,200 ft3) cells for rougher and scavenger flotation and the installation of a Svedala VTM-800Vertimill for regrinding. This paper describes the rationale behind these changes and explores the reasons for the success of the project.

Jan 1, 1999

By P. L. M. Wong, N. W. Johnson

Surface analysis by X-Ray Photoelectron Spectroscopy (XPS) of samples taken from the galena flotation section of the Hilton Concentrator of Mount Isa Mines Limited are presented. Flotation rate and pulp chemical data taken during the sampling period are also presented and discussed. Surface analysis suggested that, under normal operating conditions, an overlayer of precipitated calcium sulfate existed at the surface of the sulfide minerals. In particular, there was a decrease in the surface concentration of calcium sulfate for the concentrate samples relative to that occurring on the tailing samples. This suggests that the flotation process was selective against minerals which have calcium sulfate predominating at the surface. Heterocoagulation of hydrophilic calcium sulfate on to the galena surface considerably reduced galena flotation rate. Methods to control calcium sulfate precipitation, which include sodium carbonate treatment of the pulp, are also discussed. Sur- face analysis results of samples taken from the Hilton Concentrator during sodium carbonate addition to the grinding circuit are also presented. This shows clear evidence for the removal of calcium sulfate from the mineral surfaces without concomitant surface precipitation of calcium carbonate. Reasons for the apparent dispersion of precipitated calcium carbonate are discussed. Galena flotation rate was increased by the addition of sodium carbonate apparently due to the removal of interfering calcium sulfate.

Jan 1, 1995

By Bo Forsman

METAFORA is a simulation model for determination and evaluation of strategies for operating loader/truck systems in mining. A specific version of METAFORA was used to evaluate the haulage system at Solider Mineral's Aitik mine in northern Sweden, one of the largest open pit mines in Europe with a production of about 11.5 Mtpy (about 34000 tpd) of copper are. A production level of 34065 tpd was estimated by simulation runs with METAFORA. Using METAFORA's dispatch rules (Fixed Dispatch, Maximize Trucks, and Maximize Loaders), the truck/shovel system in the Aitik mine was simulated for evaluating alternative dispatch control strategies. The Maximize Trucks rule gave about the same total production (ore + waste) as the Fixed Dispatch rule but a 9% higher ore production. The Maximize Loaders rule gave the lowest production. The marginal truck capacity decreases with increasing number of trucks serving the same loader due to increasing waiting times. In Aitik mine the low crusher capacity results in long dumping times. If the dumping time at the crusher could be halved, the ore production would increase by 14%. The paper indicates that the use of software like METAFORA can result in a substantial reduction of time, effort and cost in shovel/truck system design and evaluation.

Jan 1, 1992