Search Documents

By L. Xu, N. I. Jayaraman, R. Bhaskar

The objective of this study is to develop a better understanding of the collection characteristics of dust measurement instruments used in mine dust control research with respect to properties of quartz and coal dust. Coal and quartz dust of narrow sues, with aerodynamic median diameters being approximately 2 µm, 4 µm and 10 µm, with quartz contents of l0%, 20%, 30%, 40% and 50%, were released in an aerosol characterization chamber using a fluidized bed aerosol generator. Dust was collected in MSA personal gravimetric samplers with l0-mm nylon cyclones, total dust samplers and Sierra 298 inertial cascade impactors. The samples were analyzed for mass and quartz content. A total of 21 experiments were performed for this study. The mass and quartz collection efficiencies of the total and respirable dust samplers and the impactor were determined. The data show that the amount of dust collected by the respirable dust sampler (respirable + oversize dust trapped in the cyclone pre-classifier) was, in general, less than the amount collected by the total dust sampler. The amount of dust collected by the impactor was higher than that collected by the total dust sampler. Quartz analyses of the airborne dust samples showed that the total dust and respirable dust samplers (including oversize dust) collect less quartz dust than at inertial impactor. The larger the median particle sire of the quartz and coal mixture, the lower the quart content of the dust collected in the samplers. For all three sires, the impactor was a better collector of quartz than the other instruments.

Jan 1, 1994

By K. S. E. Forssberg, M. I. Hallin

In many cases, the reuse of process water in flotation plants is desirable both for plant operating reasons and for environmental protection. The main advantages are better housekeeping of fresh water and process chemicals together with the reduction of polluting species to the environment. There are however a number of problems involved in the use of recycled process water. The main problem is that recycling sometimes has a deterious effect on the process and can occur months after the start of water recycling. The Division of Mineral Processing of Luleå University of Technology has been conducting experiments on recycling of process water at various sulphide plants in Sweden for over ten years. The experiments have been carried out in pilot- and full industial scale, in collaboration with the mining companies operating the plants. Until 1988 investigations were carried out in four different sulphide plants. The objectives of the experiments were: first to document differences in the composition of the process water during recycling; secondly to investigate any changes in the pulp chemistry of the flotation circuits wich may be due to the influence of recycled water; and lastly to establish critical levels, if any. of the parameters measured. While conducting experiments of this kind several things have to be kept in mind. Normally, recycling is done by using tailings pond water as process water. This means that time effects are important, because of the time lag between water input in the tailings pond and the reclaim of that water back to the plant. As will be shown, the

Jan 1, 1989

By Ned M. Smith

The Mississippian Salem Limestone, from which dimension stone is quarried in Indiana, is principally a calcarenitic rock formed of fossil bryozoans, echinoderms, and specimens of Endothyra. Numerical associations of the fossils, binding materials, oölitically coated fossils, and voids were determined by counting points on the surfaces of 278 thin sections of the limestone. Median sizes, coefficients of sorting, and skewness numbers were computed from measurements made of constituents in these thin sections. Many other samples and numerous exposures of the Salem and contiguous parts of adjacent formations also were studied. The organisms that furnished the skeletal material for formation of the Salem Limestone were chiefly gregarious and communal. Salem rocks are formed of nearly whole skeletons, of dismembered or slightly damaged skeletons, and of skeletons thoroughly ground up, because currents in the Salem sea varied in their ability to move and damage these materials. Locally the sediments are of uniform grain size because of sorting by currents and because related organisms grew to similar sizes. Rocks of the formation contain different proportions of the fauna both because the animals lived in these proportions and because their skeletons were mixed together by currents. The proportional relationships between members of the fauna were constant locally and for short periods of time. Study and mapping of the faunal associations, numbers of oölitically coated fossils, bedding structures, and size parameters enables geologists to suggest sedimentologic histories and sequences in areas of various sizes. Interpretations based upon such areal studies are necessary for evaluation of the dimension-stone potential within the Salem Limestone.

Jan 1, 1966

By Glen L. Black

Choosing a mining method for an underground orebody is a complicated and often iterative process. Advances in technology have given design teams an array of possibilities for methods and equip¬ment. Hecla Mining's discovery of the deep Gold Hunter ore body challenged the staff at the Lucky Friday Mine to determine the optimum mining method. Taking an ore body from prospect to production requires traditional resource characterization. This includes drilling, delineating and modeling. Developing the mining plan is an evolving process, changing with each new piece of in¬formation as the project progresses through exploration and development. The Gold Hunter deposit is a steeply dipping vein system in the Wallace Formation of Idaho's Coeur d'Alene mining district. Gold Hunter is a misleading name for the ore body. The vein is a silver-rich, lead-zinc deposit with only traces of gold. The Gold Hunter ore body is located about 1.6 km (1 mile) north to northeast of Mullan, ID. The ore body is mined from the Lucky Friday Mine, located 0.4 km (0.25 miles) east of Mullan. Mining began on the vein from an access drift driven from the Lucky Friday Mine's 4900 level. Production from the ore zone is projected to be 771 t/d (850 stpd). The Gold Hunter ore is combined with Lucky Friday ore and milled in the Lucky Friday mill. The combined ore boosted Lucky Friday's 1998 silver production from 62.2 t/a (2 million oz/year) to more than 124.4 t/a (4 million oz/year).

Jan 1, 1999

By M. G. Mudrey

Considerable potential for metallic mineral resources in the lower Proterozoic rock of the Lake Superior region exists (Mudrey and Kalliokoski, in press). Most of the identified resources occur within a 2.0- to 1.9-b.y.-old lithotectonic assemblage characterized by extensive sedimentary strata in the north and thick volcanic se- quences in the south, all deposited on a two-terrane, composite basement of Archean age (DeMattis, 1989). Since the late 1960s, measured resources of nearly 90 Mt (100 million st) of typical volcanogenic massive sulfide at eight localities in Wisconsin have been discovered. The largest of these, near Crandon, contains about 61 Mt (67 million st) of ore averaging 5.6% zinc, 1.1 % copper, and 0.5% lead. Although none of these properties are in production, estimates by Mudrey (1978) suggest that Wisconsin could become a major contributor of newly mined zinc and copper in the United States. These discoveries and uranium and gold discoveries in the Canadian Precambrian are what have led to in- creased metallic mineral exploration throughout the northern half of Wisconsin (Fig. 1). In this chapter, we discuss the geology and legal framework in which the Proterozoic volcanogenic massive sulfide deposits were found. Exploration activities for other metals have generally been negative, and have been background noise for the legislative activities related to the massive sulfide discoveries. Uranium exploration has been consistently negative, although several different environments have been assessed. Other metal discoveries. such as titanium/vanadium, have been subeconomic.

Jan 1, 1991

By Joseph R. Hatch

Previous studies of the Thompson and Temperly ore bodies show alteration aureoles in the Middle Ordovician host-rock limestones, dolomites and shales extending laterally as much as 60m from the ore. Thickness, texture, carbonate and clay mineralogy, major-, minor-, and trace-element contents; and carbonate carbon and carbonate oxygen Isotope compositions of the host rocks all have been significantly altered by hydrothermal processes. Organic geochemical analyses of samples from the basal 8-cm-thick carbonaceous shale bed and immediately overlying limestone bed of the Quimbys Mill Member of the Platteville Formation, collected from within the ore, the alteration aureole, and the unaltered country rock show: 1) solution of carbonates and residual concentration of organic matter, 2) decreases in the volatile (Si) and pyrolytic (S2) hydrocarbon yields In samples of the basal shale from within the ore, 3) decreases in the relative amounts of the lower molecular weight (<nC25) saturated hydrocarbons in samples from the ore, and 4) no changes in either the organic carbon isotope composition or the Rock-Eval or biomarker thermal maturation Indicators. In light of the 125-170°C depositional temperatures documented for the early marmatitic sphalerltes in these deposits by fluid Inclusion studies, the lack of thermal alteration of the organic matter suggests a relatively short mineralization episode, a conclusion supported by the relatively simple sphalerite band stratigraphy. The decreases in the volatile and pyrolytic hydrocarbon yields for shale samples from the ore supports a model for mineral deposition which obtains sulfide through reaction of brine sulfate and indigenous organic matter.

Jan 1, 2013

By Allan M. Johnson

Since 1974 researchers at Michigan Technological University have been studying mine subsidence in the Iron River District of Northern Michigan. The district, which was active from 1881-1978, has had numerous cases of subsidence. Much of the subsidence resulted from rock mass failure but some appeared to have developed primarily in the thick glacial overburden which is a typical feature of this area. This latter observation led to the recognition that some of the surface subsidence was due to piping; i .e., loss of overburden material to the mine voids by groundwater flow (Johnson and Frantti, 1978). The Sherwood Mine was the last mine to operate in the district. With its closedown scheduled for late summer of 1978, a unique opportunity to monitor the mine as it flooded was presented. It was reasoned that with the cessation of pumping, groundwater would rise in the overburden and the mine would flood. The physical characteristics of the mine were favorable for piping to occur as the mine flooded. With the permission of Inland Steel Mining Company and the support of the U. S. Bureau of Mines, a project to monitor the Sherwood Mine for piping subsidence began in June of 1978. This paper present aspects of this study pertinent to the piping-induced subsidence events which occurred at the Sherwood Mine in 1980 and 1981, including acoustic emission monitoring of the subsidence activity, hydrologic monitoring of the groundwater regime and the flooding mine, laboratory modeling of the piping mechanism, and analytic procedures which are under development.

Jan 1, 1982

By John Armstrong, Michael Savill, David Powell

Hong Kong is an intensively developed region and has the highest vehicle densities in the world. In 2000 there were 6.6 million people and 580,000 vehicles using 1,890 km of road covering the 1084 km 2 territory. The high vehicle and population densities together with the difficult terrain have seen road tunnels emerge as key components both in the current and future road transportation network. Currently there are eleven operating highway tunnels in Hong Kong, seven government owned and the remaining four “build, operate and transfer” franchises, see Figure 1. The very first tunnel was the dual two Lions Rock Tunnel completed in 1967and the latest the dual 3 lane Tai Lam Tunnel opened in mid 1998. Figure 2 shows the alignment and statistics for all 11 Hong Kong tunnels. Looking ahead, Hong Kong has embarked on the study and design of the next generation of major highways and as many as a further seven tunnels are currently under feasibility study or detailed design. This seems an opportune year to produce a broad appreciation of the fire strategy, life safety and ventilation practices in Hong Kong not only for the existing tunnels but the new standards and requirements for the next generation of Hong Kong tunnels. This paper provides an overview of the fire strategy, life safety and ventilation of Hong Kong’s existing and planned tunnels. The paper pays particular attention to the areas where the unique conditions and requirements in Hong Kong impacts on tunnel and systems design and the solutions adopted to overcome these challenges.

Jan 1, 2001

By John W. King

reserves are exploring to increase them.. Uranium exploration projects are known to be active or planned also in Guayana, Colombia, Ecuador, Peru, Chile, Bolivia, and Uruguay in South America; in the UAR, Nigeria, Angola, Mozambique, Malawi, Kenya, and Somali in Africa; and in Greece, Iran, Pakistan., Indonesia, and New Zealand. The above list, to which several might be added makes a total of at least 43 nations actively interested in exploration for nuclear raw materials. As we consider the distribution of the world&apos;s uranium resources, it is interesting to note that roughly one third of the total occurs in deposits that are economically dependant upon another product. The very large reserves of South Africa could not be produced for uranium alone, but gold has carried a sufficient part of the total cost that uranium can be recovered profitably. Approximately 40 percent of the US reserves, or 120,000 tons, are estimated as by-product recovery from porphyry copper and phosphate operations, but these reserves are not presently in production. The remaining two thirds of the world&apos;s uranium reserves have been sought, developed, and produced primarily for their uranium content. Those deposits are estimated to contain 613,000 tons of uranium oxide recoverable at less than $10 per pound. Nearly half of that uranium occurs in unmetamorphosed sandstone hosts, mostly of late Phanerozoic age--the Colorado Plateau type. About 30 percent is contained in the quartz pebble conglomerates of southern Ontario, Canada, and 20 percent is in magmatic-related deposits--veins, contact deposits, mineralized breccias, etc.

Jan 1, 1969

By Hans Janzon, Ernst Buechi

INTRODUCTION The headrace tunnel in Amlach is part of a hydro electric power scheme near the city of Lienz in south west Austria. The project is owned and developed by Tiroler Wasserkraftwerke AG, the regional electrical supply utility. The construction work was divided into seven contracts for the entire scheme. The power output will be 60 MW, this being developed from a head of 370 m and water flows of 20 m3/s. The water will be tapped from the river Drau and lead through a 22 km long headrace on the south side of the Puster valley through the Lienzer Dolomiten mountain range. Contract No. 4, which is a joint venture between Mayreder, Züblin, Strabag, Rella and Innerebner, involves the construction of 13.5 km of the headrace. It was decided to bore this from one single adit, which probably makes it the longest pressure tunnel driven from one side by a TBM. (See Fig. 1.) For the tunnelling an Atlas Copco Jarva MK 12 TBM was chosen. The excavation diameter is 3.90 m, with the final lined diameter being in the range of 3.20 to 3.40 m. The back-up is a 145 m long single track rail system supplied by Mühlhäuser (Germany). Side-tipping cars with a capacity each of 8.2 m were used for removing the muck. One California switch was attached to the back-up after 3,000 m, and a second fixed switch was installed after 8,000 m of boring. 3 m long

Jan 1, 1987

By W. White

The manuscript of this paper was not available for publication when the Proceedings went to press. Should the author elect, he may distribute copies at the time of the Symposium.

Jan 1, 1986

By Ananda M. Wijesinghe

The manuscript of this paper was not available for publication when the Proceedings went to press. Should the author elect, he may distribute copies at the time of the Symposium.

Jan 1, 1986

By Wang Zuoyu

The manuscript of this paper was not available for publication when the Proceedings went to press. Should the author elect, he may distribute copies to the time of the Symposium.

Jan 1, 1986

By Michael M. Maier

The manuscript of this paper was not available for publication when the Proceedings went to press. Should the author elect, he may distribute copies at the time of the Symposium.

Jan 1, 1986

By Stuart Brashear, J. W. Reil

The manuscript of this paper was not available for publication when the Proceedings went to press. Should the authors elect, they may distribute copies at the time of the Symposium.

Jan 1, 1986

By James L. Withiam, P. C. Kelsall

The manuscript of this paper was not available for publication when the Proceedings went to press. Should the authors elect, they may distribute copies at the time of the Symposium.

Jan 1, 1986

By H. Walqui, C. Noriega

Southern Copper Corporation (SCC) is one of the world’s largest copper companies and is finishing the modernization of the Ilo copper smelter. A single ISASMELTTM furnace will start smelting 1,200,000 tons per year of concentrate at the end of 2006. Three existing Peirce Smith converters are being upgraded plus a new one for converting the matte to blister copper is being installed. Two new anode furnaces and a twin anode casting wheel have being operating since January 2006. This represents one of the main changes in the process because the final product of the smelter is now anode copper instead of blister copper. A new oxygen plant, acid plant, and others facilities are in the ramp-up stage. This environmental project will ensure that the new smelter will comply with the environmental regulations of Peru by the end of January 2007. This paper summarizes the background to the modernization project, describes the different stages of the project including engineering, procurement and construction, describes the main areas of the new copper smelter and also the pre-operational testing, commissioning and start-up of them. This is a brown field project with a target of reducing as much as possible the production losses of the existing operation. This paper presents the details of the development of the Ilo Smelter Modernization Project and explains the main aspects of the new facilities, the products to be obtained and the associated facilities for their commercialization, including a Marine Trestle for bulk acid exportation.

Jan 1, 2007

By Brian Garrod

Increasing use of pressurized-face tunnel boring machines in North America has produced a similar increase in the application of precast concrete tunnel linings. Where a pressurized TBM is needed, immediate ground support and ground water pressure resistance is also required. A segmental lining installed within the TBM tail shield provides the only available means of providing such a sealed lining. This paper addresses new developments in North America in lining applications and design. For the purposes of this paper, a precast concrete tunnel lining is defined as a tunnel lining constructed using precast concrete segments that are assembled into a lining ring. The lining rings are connected adjacent to each other to form a tunnel lining. Each segment has a sealing gasket around it so that when the lining is completed, it provides a fully waterproof lining system. The ring is erected within the tail shield of the TBM and the annular gap around the ring is filled with grout as the machine moves forward. The ring is not expanded and normally provides the finished lining of the tunnel with no requirement for a second pass lining. The TBM has a series of hydraulic rams that push on the leading edge of the segmental lining to provide the sole system of forward propulsion for the machine. The rings are tapered, being longer on one side than the other. This allows the rings to be installed either on a curve or in a straight line depending on the rotational position of the rings.

Jan 1, 2008

By R. C. Warner, L. Mills, S. D. Botts, M. Marticorena

The Antamina Mine is located in the mountainous region of the Ancash Department of Peru at an elevation of approximately 4200m.The 120 km main access road crosses the headwaters of numerous high-value trout streams and is adjacent to pristine lakes, some of very high ecological and scenic value. In addition, the mine discharges mine water and tailings supernatant to the Antamina and Ayash watersheds. These streams provide the primary water supply for irrigation by local residents and provide excellent fishery habitat. The rock walls and earthen diversions constructed by historic and current indigenous residents of Peru are world-renowned and local residents continue this tradition, passed down from the Inca Civilization, for both agricultural purposes and water distribution. The key elements of sustainable development – economic, environmental and social development have been incorporated into Antamina’s sustainable development program through integration of indigenous knowledge and capabilities into enhanced storm water, erosion reduction and sediment control systems. Examples of incorporating indigenous technologies and knowledge into cost-effective and environmentally sound environmental controls are:(1) placement of rock walls on steep terrain to reduce slope length and erosion, (2) installation of rock walls (porous rock check dams) within elongated sediment ponds to increase detention time, (3) construction of rock-lined ditches to convey clean water (4)use of rock walls, with or without geotextile, to function as a seep berm, and (5) appropriate selection and usage of native Andean species for protection of canals and sediment ponds, and steep slopes.

Jan 1, 2004

On June 4, Kennecott Utah Copper (KUC)marked the centennial of the founding of the original company. Bill Champion is president and chief executive officer of KUC. He said, “What has happened during the past 100 years far surpassed even the most optimistic visions of men like Daniel C. Jackling and Robert Gemmell when they promoted the concept of mass production techniques for a low-grade deposit of copper ore. At that time, it was a totally new way of doing things and the mining leaders of that day scoffed at the idea. They said it would never work,” Champion said. The company will celebrate this once-in-a-lifetime occasion with a few special projects, mainly for the benefit of our employees, said Louie Cononelos, director of government and public affairs for KUC. The company has designed and minted a commemorative copper coin that reflects early steam shovel and locomotive operations on one side, and today’s modern electric shovels and huge haulage trucks on the other side. “The history of the company stems from the ores of the Bingham Canyon Mine. That coin has been encased as part of a10-panel brochure that captures the company’s 100 year history,” he said. KUC also developed special centennial banners and comparable framed posters that were displayed throughout its operations and at selected community locations that have enjoyed a long-time partnership and special relationship with the company. Some of the plants also designed their own centennial hardhat decals.

Jan 1, 2003