Search Documents

By V. Galla

In the present paper, two large diameter columns 2 m tall and 1.3 m diameter filled with crushed (finer) and run off mine (coarser) heap leach materials respectively were used to perform unsaturated flow studies. Instruments measuring moisture content and matric suction were placed in the columns at different depths as water was applied at calibrated flow rates from the top of the columns. The outflows from the columns were recorded using tipping bucket rain gauge placed at the bottom of the columns. Unsaturated hydraulic parameters were also obtained for the heap leach materials, scalped (passing 4.75 mm sieve size) and whole (passing 37.5 mm sieve size) sample. The measurements obtained from the columns were later compared with unsaturated flow modeling results. The comparison indicated sensitivity towards the sample size selection for unsaturated hydraulic parameters, and initial conditions considered in the model.

Jan 1, 2009

By Joseph P. Sobanski, Michael P. Bruen

The North Branch tunnel segment of the Tunnel and Reservoir Plan Mainstream System consists of 14,075 m (45,885 ft) of 9.2 m (30.2 ft) finished diameter and985 m (3,232 ft) of 2.5 m (8.25 ft) finished diameter concrete lined rock tunnels. The TBM mining and concrete lining methods used in completing this $166million project differed from “typical” TARP construction methods in that a two-stage concrete lining was placed and the lining was initially placed concurrently with TBM mining as a two pass system in the same tunnel segment. For the main tunnel (9.85 m diameter), TBM mining averaged 24 m/day (79 ft/day), excluding downtime associated with two main bearing changes, and the concrete lining placement, averaged 117 m/day (380 ft/day) and 53 m/day (174 ft/day) for the invert and arch segments, respectively.

Jan 1, 1999

By Z. Mullard

The introduction of social media platforms has ushered in a new era of interaction and information exchange, which impact business-to-society relationships. Mining companies are closely watching these platforms, as the industry takes a cautious approach to control flows of information. This paper explores the risks, challenges and opportunities of using social media, based on a qualitative mixed methods investigation with stakeholders from the Canadian mining industry. Generational and language barriers, misunderstanding and limited motivation from regulators make implementing social media platforms challenging and risky at an organizational level. The benefits of social media include being able to mobilize communities and share information in real time. Despite the challenges, the study found that 62% of mining stakeholders are incorporating social media tools, mostly in an ad hoc manner. Flexible strategies for transparent communication and public engagement are creating new opportunities for information exchange.

Jan 1, 2011

By J. T. Bartlett

Life-of-mine process simulation is an interdisciplinary effort and a useful means of thoroughly evaluating mining and minerals projects. Communication between geologists, mine planners, miners, metallurgists, and managers not only benefits each discipline but facilitates design of an efficient operation and allows for accurate forecasting of productions and cash flow. By focusing on the key areas: geology; mine design; waste dumps; stockpiles; metallurgy; weather data; tailings disposal; using contours, block models, mine plans, process flowsheets, design criteria, operating and control strategies, maintenance schedules, and operating costs to perform detailed daily simulation from start-up to shut-down; a comprehensive understanding for all disciplines is achieved. Construction of a METSIM model that includes all test work and project data from drill holes through net present value calculations brings the pieces together to achieve optimum process design, minimize operating problems and eliminate the term ?black box? from project meetings and discussions.

Feb 27, 2013

By Robert A. Pond

Heavy (exceeding 35 tons) roadheaders have not seen much use in the United States, but are used extensively in Europe to excavate many types of underground openings in civil and mining applications. Early models of roadheaders were light and suitable only for utility excavation such as drift enlargement or chamber excavation, unless the ground was very soft and easily cuttable. Frontier-Kemper Constructors, Inc. is now using a 45-ton roadheader to excavate two mine slopes in Kentucky and a 70-ton roadheader to excavate a long decline at a new mine in Utah. Results to date indicate that heavy roadhead machines are an effective alternative to both conventional excavation and full-face boring machines in many cases; and where circumstances are favorable are a superior choice. This paper concentrates on applications in the mine development construction industry, but the conclusions are no less valid for civil construction.

Jan 1, 1983

There are multiple stages in a mining operation that a mining engineer has to draw polygons to be used as operation guidelines. These polygons are drawn by hand and based on engineer?s experience. However, having automatic procedures for forming the shapes can increase the quality and decrease the efforts required. These shapes need to be homogenous in grades and rock types so that the quality and dilution of material sent to the plant can be estimated with the good approximation. In this paper, a clustering algorithm with shape control is introduced which can provide reasonable guidelines for all the aforementioned shapes by manipulating its parameters. At the end, implementations of the algorithm on a small part of a gold deposit with different mining strategies is presented and evaluated based on homogeneity of grade, rock types and determined destinations as well as the shape.

Feb 27, 2013

Ceremonies for the induction of five mining industry pioneers into the National Mining Hall of Fame are scheduled for Saturday, Sept. 25, 2004 at the Las Vegas Hilton in Las Vegas, NV. The 17th Annual Mining Hall of Fame Induction banquet will begin with a reception at 6 p.m., followed by the dinner and program at 7 p.m. The five inductees are Georgius Agricola, David William Brunton, Herbert E. Goodman, David Ray Mitchell and Robert Peele. Georgius Agricola (1494-1555) wrote De ReMetallica, an original and valuable work that discussed everything known about mining during the first half of the 16th century. In De Re Metallica, Agricola reviewed practical means of finding ores, methods of surveying and mining, the assaying of ores, types and uses of mining machinery, smelting, mine administration and more. David William Brunton (1849-1927) is best know

Jan 1, 2004

By C. Green, J. Uhrie, C. Filippone, A. Guzman

A central aspect of heap leach management and recovery optimization is solution control. Insofar as each heap is unique in physical and metallurgical properties, it is essential to understand the hydraulic parameters that control the migration of solution on a case-by-case basis. Water Management Consultants, as part of an ongoing research effort for Phelps Dodge Process Technology Center, have adapted techniques of parameter estimation for application to data typically resulting from metallurgical column testing. The parameterization is completed within the context of a variably saturated flow model that allows interpretation of available hydraulic information collected during hydrometallurgical column tests. A novel interpretation approach is introduced to extract the necessary hydrodynamic parameters from typical hydrometallurgical data sets. Results from the application of the approach to standard metallurgical test data will be presented together with a discussion of the application of information gained to the design and operation of a heap.

Jan 1, 2002

By Alan Zeni

Blind shaft drilling equipment has not changed substantially since the 1970s. Since it resides in a niche market between conventional shaft sinking and raise boring, the relatively small demand has resulted in some stagnation of development. In the 1990s the technology found a larger foothold in foundation and deep piling work for civil construction. WIRTH GmbH from Erkelenz, Germany has been servicing this market for many years with pile top drilling rigs and tools. Frontier-Kemper Constructors, Inc. recently entered into an agreement with WIRTH to develop a new generation of large diameter blind drilling equipment more specifically aimed at mining needs. The, recently completed, DHI-240 is the first rig to apply the most recent technology. This machine made its commercial debut in the fall of 2008. A description of the technology and a short case study of the first project will be described

By James J. Graham

Uravan, Ambrosia Lake, Gas Hills and South Texas are all historic names in US uranium. These mining areas supplied the uranium that brought the United States into the nuclear age during the 1960s, and fueled the birth of nuclear energy for peaceful uses — a promise of nearly limitless, clean energy for the world’s future. That promise still exists today, but it is hard to hear over the rhetoric of environmental activists and politicians. Nuclear power offers dependable electricity with limited environmental impact at stable prices. Nuclear power releases no greenhouse gases or particulate matter into the atmosphere. High level nuclear waste (HLW), although long lived, is readily controlled and compact. In the United States, generating 1 billion kWh of electricity with coal produces 47 kt (52,000 st) of solid waste (ash and sludge), compared to 3.6 t (4 st) of HLW produced by nuclear.

Jan 1, 2002

By Bill Elverman

Randy and Kenny Robison have visited every coal mine that would let them in the door, to survey the best mining practices. The brothers have spent nearly their entire lives working in coal operations. The Robison’s started out on lube and grease trucks and worked their way up to respected industry leaders in Alabama. The Robisons have owned MS&R since 1989. Since then, they have created a niche for themselves in providing coal for Alabama’s metallurgical coal market. A great deal of the knowledge the Robisons have amassed throughout the years has come from observing — taking note of what works and what does not. In early spring 2004, they commissioned a Komatsu America PC3000 Super Shovel. Outfitted with a backhoe attachment and a 16-m3 (21-cu yd) bucket, MS&R’s PC3000 is currently one of the largest mining excavators working in Alabama.

Jan 1, 2005

By F. M. McEvoy, E. J. Steadman, R. Murfin

In England, the provision of aggregate is determined by the historical relationship between construction and aggregate consumption. This approach does not necessarily lead to sustainable decision-making and can be seen as being driven by political expediency, rather than reasonable environmental consideration. The introduction of the statutory requirement for Strategic Environmental Assessment (SEA) in the UK has provided the opportunity to examine this issue on a more rational basis. This paper provides a practical application of a SEA based approach, to the provision of aggregates at a regional level. The process, underpinned by relevant information on resources and environmental assets, suggests that alternative supply scenarios for aggregate provision are tested in a transparent, consistent manner with increased genuine stakeholder consultation. It supports a move away from "predict and provide" approaches to one where aggregates are sourced with the best balance of environmental costs and benefits.

Jan 1, 2005

By S. K. Oraee

Most management decisions at all levels of the organization are as directly or indirectly depends on the circumstance of future. With regard to predict the future events in the process of decision-making plays a main role, therefore, forecasting is very important for every organizations and institutions. There is a variety of methods to predict time series. In general, these techniques can be divided as following: statistical, artificial intelligence and analytical techniques. Two of the most common methods for time series prediction is autoregressive integrated moving average (ARIMA) and artificial neural network (ANN) methods, these methods are the subset of statistical and artificial intelligence techniques respectively. In this paper, a hybrid model of ARIMA and ANN models are employed to predict the number of fatal injuries in the USA underground coal mines. This research showed the result of hybrid model is better than split model.

Jan 1, 2011

By C. R. Copeland

Combustion processes, comminution and materials handling can generate airborne particulates. Regulation of these particulates by the U.S. Environmental Protection Agency (U.S. EPA) is becoming progressively more stringent, and regulations will soon include ?nanoparticulates,? which are particles finer than 100 nanometers (0.1 mm). Nanoparticulates are believed to have significant negative health effects due to their high surface area and reactivity. Although it was argued that nanoparticulate concerns were only important for combustion, studies at Michigan Technological University have shown that materials handling and comminution release significant quantities of nanoparticles into the air. Laboratory studies have shown that the use of sodium metasilicate reduced airborne particles finer than 10 mm (PM10) by 86% and particles finer than 2.5 mm (PM2.5) by 80% for iron ore. Additional studies were conducted that revealed that nanoparticulate emissions were present in the types of operations conducted at pyrometallurgical facilities.

Jan 1, 2008

By Larry D. Hartzog

For detailed information you are referred to "Heap Leach Solution Application at Rochester" by S. N. Dixon and A. L. Wilder which will be presented at the SME Meeting in Phoenix, January 1988.

Jan 1, 1998

By Dean Workman

Located in downtown New York City, this project necessitated an innovative conveyor design for successful muck removal. This paper will discuss the technical challenges and engineering solutions of the muck transport system which consists of every commonly recognized version of a belt conveyor. The elaborate system includes a TBM conveyor integral to the back-up system, a wall-mounted extensible conveyor, a crown-mounted transfer conveyor, a floor-mounted fixed-length conveyor, a pocket-belt vertical conveyor, three cascading overland conveyors, and one radial stacker. The most challenging design element was an over-land conveyor featuring a box truss for muck transportation over Northern Boulevard while simultaneously going under the Queens Plaza railroad viaduct. An overview of the project is provided along with the following topics: developing final plans from the proposal concept, interfacing with existing works, communication with the joint venture, and complying with local regulations.

Jan 1, 2008

By B. S. Crocker

Introduction Pebble mill grinding can be defined as wet or dry grinding in a tumbling mill with pebbles used as grinding media instead of metal balls. To clarify the terminology, which may differ in the various mineral industries, it is essential to point out the differences between grinding with partially sized and carefully sized grinding media. When grinding with partially sized media (limited top size only), sizing is usually the setting of the primary crusher and there is no bottom sizing-all fines, chips, sand, and small sizes are included. This is often called run-of-mine or primary autogenous grinding. In this case the entire crusher discharge is fed into the mill and part of it becomes "charge" and the rest is "sand feed." When grinding with carefully sized media (i.e., media that is sized both at the top and bottom of the size range), no fines or chips should be present in the charge to the mill. This is pebble milling and the grinding media consists of ore, rock, Danish pebbles, gravel pebbles, or ceramic pebbles-media that is appreciably lighter than steel balls. The grind¬ing charge is fed to the mill to maintain a load and it does the grinding usually on a classified sand product of suitable size. If the grinding media is the same as the raw material being ground, this type of grinding is also called secondary autogenous grinding. Pebble milling was in common use in the gold mines of South Africa in the early 1900s. It is by far the oldest form of autogenous grinding. It may be used to grind crushed ores from a maximum size of about -% in. to all -10 µm. Pebble milling differs from "run of mine" grinding in many ways, but two big differences are: I) The ore itself is crushed to approximately t/4 in., or it may be further reduced to 8 or 10 mesh in a rod mill or fine crusher. 2) Then carefully screened ore of the correct size is placed in one or more stages of pebble mills to grind the ore to its desired final size. The media size is carefully selected to be the most efficient for the particular size reduction required in each stage. This is a precise practice, and pebble mills can be designed as easily and accu¬rately as can rod mills or ball mills by those skilled in the art. A pebble mill is a rotating cylinder in which the grinding media has been carefully sized for the job in hand. If the mill is doing coarse grinding, the media will be correspondingly large and the mill might be called a primary (or intermediate) pebble mill or a lump mill. If it is to do fine grinding, the media selected is proportionately smaller and the mill would be called a secondary or tertiary pebble mill. The media itself is normally rounded pebbles made from screened ore from the primary-crusher discharge. The charge could be rounded pebbles of the correct size removed from a primary autogenous mill, or the pebbles could be carefully sized gravel, sized beach pebbles, or sized flint pebbles. Usually the specific gravity of a pebble is from 35 to 55% of that of steel balls. It commonly varies from 2.66 to 4.2, depending on the specific gravity of the ore. Primary pebble mills, or lump mills, would be charged with pieces of rock up to 10 in. maximum and 5 in. minimum and would grind crusher discharge with a maximum size of 1/4 in. on hard ores and 3/8 in. on softer ores. Secondary pebble mills could be charged with pieces of rock screened on 4 x 4-in. square mesh and retained on 1 1/2 x 1 1/2 in. These mills would grind material with a top size of 8 to 10 mesh. Tertiary pebble mills could be charged with screened rock that would pass 3 x 3 in. and be retained on 1 x 1 in. and grind 35 to 48 mesh sands. Principles of Operation Media Size To operate a pebble mill efficiently it is imperative that great care be taken in screening the rock feed that is fed into the mill to round up into a range of pebble sizes that are suitable for grinding of the sands that are also being fed into the mill, having regard to the top size and the average size of such sands. Since most mill operators know from experience the correct size of steel balls to be used in a mill to handle different sizes of sand feed, it is convenient to relate the pebble size to a ball size. If the correct ball size is not known, it is relatively simple to conduct batch laboratory tests in 12- to 18-in. laboratory mills to determine the optimum size of steel ball. Also, Bond and others have published formulas for calculating the optimum ball size. When the correct size of the individual steel ball is known, then a pebble of the same weight will perform the same grinding if used in the proper size of mill and under the proper conditions, which will be defined later. This media size, as defined by the average weight of the individual pieces, is most important. The following tests will serve to clarify this point. Laboratory Tests Using Steel Balls or Pebbles. Several labora¬tory grinds were made to compare a given size and weight of steel ball with a pebble of the same weight but larger size, and of the same size but lighter weight. The following loads were used in the 12-in. laboratory mill: All 1 1/4-in. steel balls weighing 122 ± 10 g. All 1 3/4-in. pebbles weighing 123 ± 5 g. All 1 1/4-in. pebbles weighing 45 ± 3 g. To equalize capacity, the test with the steel balls was run only 34% as long as the tests with pebbles. In each case, 2,500 g of primary sands were ground at the optimum gravity for the media being tested at a speed 78 1/2 % of critical speed, and for 170, 340, and 680 revolu¬tions for the steel balls, and 500, 1,000, and 2,000 revolutions for the pebbles. The first test is summarized in Table 74 by showing the 80% passing size in microns for the feed and for each of the grinds. Two other tests are summarized in Table 75 showing the screen analyses

Jan 1, 1985

By M. J. Ramos

Without an exclusive definition of administration in business, we could propose to define it as performance by management to adopt or implement established business formulas. Administration could also be defined as a universal process that organizes people, and achieves, through efficiency, common objectives and goals. Humanity developed some form of this process from the beginning of civilization. To imply that something is new in administration might be considered specious or naïve. Moreover, what is new in management? Administration of business is not new to the world. To prove this statement, we need only ask this question: Does the architecture and monumental workmanship of the past civilizations of ancient Egypt, Rome, and the Incas demonstrate management without administration and without definition of objectives? The answer must be a resounding ?NO!? In spite of this acknowledgment and for the purposes of this presentation, I will use the word ?new? in business and hope that the reader will follow my reasoning. The mining industry has unique characteristics in respect to other industries. It is multi-disciplinary, has a single purpose (majority for one metal), has two players (man and nature), and it involves high risks for generating environmental imbalance. Mining exploits non-renewable and finite resources, creates an unstable job market (work hard to have no work) and a speculative economic market with unpredictable prices ? a one-time payment for a finite resource with multiple recycling. On top of all that, the industry still operates within obsolete petroleum-based technology, utilizing practices that were designed two centuries ago. Today, we confront the challenges of the millennium with outmoded practices and management. Ordinarily, several styles of administration are standardized into a FRAGMENTED vertical system of organization. Mining has rigid objectives in production, with profitability as the focus from the beginning to the end. Citing the concept of safety, as an important facet of production is bombastic since, in truth, mining is an experimental industry that consistently reports high numbers of fatal accidents. In mining, we designed a process to work according to our objectives, demanding attention and supervision of all levels of management with a halo of parameters that are not assimilated into the design. We continue to perform a rigid style of management in an industry that is still not responsive to variations of the market ? losses in particular. The existing design process generates loss without capitalization and without response to said loss. This perception is reflected in a mindset that is only too ready to ignore mining liabilities. The reality of the enterprise has created an immense pressure from top to bottom in the hierarchy to do more with less. It is for all of these reasons that I propose to set forth a new essence for administration that encompasses an alternative vision and style in mining: Management by Loss. MANAGEMENT BY LOSS Management by Loss (MBL) is a systematic, integral process organized to quality control operation and the human profitability within the industry. It permits focus on achievable goals by utilizing the best practices (Mining Open-closing). Identification and characterization of loss in the process determine how objectives are defined, controlling the time limits to execute based on constant balance of mass, energy, water, and ?wastes? in each stage of the industry, in order to reach final objectives. The concept of loss can be defined by various criteria. Generally, it is the mass that could not make or arrive at its destination from a designed process or simply, it could not maintain balance. Otherwise, the design of the process describes the final point of the resource. However, those resources could not make their destination because of failure to use the best design, resources and TIME. The loss has typical characteristics such as Identifiable, classifiable, measurable, manageable, controllable, valuables, negotiable, avoidable, reportable, and monitoring. In the traditional scheme, these losses are not registered; they are made exclusions. We are trapped within a system, which was designed to obtain objectives of the industry in a specific timeframe. In the present style of administration, the focus is total - our emphasis in this treatise is in the loss. The current traditional report form contains only the most positive achievement of objectives, only the best of the exercise, humanizing numbers, without touching what we left behind or what we were waiting for to assimilate as a ?surprise account?(new account of liabilities). Management by loss is a method that redefines the concept of waste (waste zero) for controlling the mine operation under the equilibrium of the ecosystems. This method confronts the problems that impact our industry in this millennium. Understanding and quantifying losses (reserves, resources, time, energy, water, soil, materials, equipment, tasks, labor, ecosystems, etc) is a priority mandate for the industry and demands the application of a ?new ? style of administration by seeking to maintain balance instead of the disequilibrium that mining now creates in nature. It is necessary to answer questions such as: How can we minimize loss? How can the loss be assimilated during the life of the mine? What is the vision of mining in respect to the generation of waste? How can we convert liabilities into assets? In addition, the control of loss is determined in the achievement of the plan. Loss occurs because of a failure of the process in the original plan. Still we do not plan to fail but we fail to plan appropriately. It is a remarkable thing to accomplish and compel those objectives described in the original plan when that plan is designed with a determined budget. If not, we lose time and, of course, capital. Moreover, in Management by Loss (MBL), we can find answers to the following questions: What is the multiplier of productivity in mining? What are the influences of identification and characterization of loss and what is the level of efficiency of energy in order to achieve waste zero (effective cut off grade)? The challenges of mining in this millennium validate this new style of administration. Finally, it is important to point out that mining is entering into an era that has different rules, but the industry is still run by companies functioning with objectives from two centuries ago. They are trying to confront issues with concepts that are not designed for new tasks. Therefore, I ask you to consider this new style of administration of business under a vision of how the industry should be organized and managed, with an attitude of balance toward nature and social responsibility.

Jan 1, 2009

By B. Caro Vargas

The Toulon Tunnel project is a key component of the highway corridor on the French Riviera between Marseille and Nice and is a fundamental transportation infrastructure for the region. The first design studies started in the 1960s. The tunnel project is comprised of two separate tunnels: south and north. The north tunnel was built between 1992 and 2002 after 10 years of difficult construction. On March 15, 1996, for example, a collapse of the tunnel in the Marchand area generated a sinkhole in the city center, causing a 20-month delay. The south tunnel alignment runs parallel to the north tunnel below Toulon?s historical downtown at a depth of 20 to 40 m (65 to 131 ft) with some areas with less than 10 m (32 ft) of cover. The risk management program was studied to be a state of the art program in urban tunneling construction.

Jan 1, 2012

By P. T. Bissert, L. Yan, J. R. Srednicki, J. A. Yonkey

"Refuge alternatives (RAs) are required in underground coal mines to support life post-disaster. RAs are mandated by MSHA to maintain an apparent temperature (AT) at or below 95°F (35°C) while providing a safe and livable shelter for a minimum of 96 hours. Because strata composition and mine temperatures will affect the final AT within an occupied RA, NIOSH researchers have collaborated with five underground coal mines across the US to characterize the effects of geographic location and seasonal temperature fluctuations on mine air temperature, relative humidity, and mine strata temperatures. The data collected indicates that some mines will experience greater temperature fluctuations than others, based on geographic location. The mine which demonstrated the greatest temperature differential over the course of the year resulted in a mine air temperature that ranged from 53.4°F (11.9°C) to 84.2°F (29.0°C) and a rib surface temperature that ranged from 55.4°F (13.0°C) to 82.8°F (28.2°C). This data suggests that the location and seasonal peak temperature can significantly affect the mine strata temperature, which could lead to a fully occupied RA exceeding the 95°F (35°C) AT limit over the course of 96 hours. The data reported in this paper could be used to examine the heat buildup inside an RA for actual mine conditions. Thermal simulations could be implemented to evaluate maximum occupancy ratings based on actual mine temperatures and strata compositions. INTRODUCTION In the event of a mine disaster, miners’ primary focus is to escape. Should their attempt be futile, they can enter a refuge alternative (RA) to await rescue. In 2008, the Mine Safety and Health Administration (MSHA) mandated that underground coal mines implement RAs within 1,000 ft (304.8 m) of the working face and spaced within one-hour travel distances in outby areas where persons work such that persons in outby areas are never more than than a 30-minute travel distance from an RA or safe exit. These RAs are required to provide a safe and habitable shelter for a minimum of 96 hours and to prevent the apparent temperature (AT) from exceeding 95°F (35°C) [1]. There is concern throughout the industry that in some cases the internal ambient of occupied RAs may exceed the 95°F (35°C) AT limit due to the potentially hot mine atmosphere as well as the metabolic heat generated by RA occupants and the carbon dioxide scrubbing system. The National Institute for Occupational Safety and Health (NIOSH) has conducted tests in its Safety Research Coal Mine (SRCM) and its Experimental Mine (EM) to investigate heat buildup in RAs. It was found that the number of occupants in an RA may need to be reduced based on the ambient mine temperature, which varies from mine to mine [2]. Further testing and analyses were completed to evaluate the mechanisms (conduction, convection, radiation) by which heat is transferred from an RA to the mine surroundings. Additionally, the effects of varying mine strata compositions on the heat buildup inside an RA were studied [3]. The mine strata temperatures will increase due to heat transfer from within an RA. Depending on the mine strata composition, some mines may be more thermally conductive than others. For example, sandstone is much more conductive than shale or coal (i.e. it disippates heat at a quicker rate). All things being equal, the air temperature inside of an RA after 96 hours will be higher for a mine with strata that has low thermal conductivity compared to a mine with high thermal conductivity."

Jan 1, 2017