Search Documents

By A. G. Sciulli, G. P. Ballock, G. Hearnshaw, K. K. Wu

Waste disposal underground is the most effective method when viewed from an environmental aspect. As costs of other methods of disposal continue to escalate, the cost effectiveness of underground disposal during the mining cycle becomes increasingly attractive. The use of concrete for sealing abandoned mines has proved to be suspect when associated with a relatively incompetent adjacent strata due to its shrinkage characteristics. Complete failure of the plug has been known to occur in some instances. A more effective, cost competitive seal can be obtained using pneumatically stowed material and incorporating a polyurethane grout, which has greater adhesion characteristics than concrete. Injection of the surrounding strata and of the stowed material helps to ensure an impervious barrier and prevent the plug from moving when subject to high pressure heads. When properly placed, impervious seals cause the old workings to flood, raise the mine pool level, and thus eventually eliminate the potential for oxidation, which is the primary cause of acidity in the water

Jan 1, 1987

By D. Harney

Accurate measurement, tracking, and planning are vital for efficient utilization of energy in any mining operation, the major focus of this paper. This can be done with a number of assessments: 1) accurately measure KWH usage and track peak demand periods first; 2) identify the electrical equipment that affects your usage and the conditions that require it to be running; 3) remotely monitor and control as much equipment as possible, especially larger pieces of equipment; 4) with your utility determine that you are on the most suitable rate for your usage profile, then understand how your utility company calculates your electrical bill; 5) recognize how production affects energy usage and utility costs; 6) keep historical records of everything you monitor; 7) make information, live and historical, available to everyone; and finally, with the knowledge of your equipment and energy needs, automate controls that you have identified to optimize your energy usage and time of usage.

Jan 1, 2007

By William A. Gibson, Kenneth P. Neumann

In 1967, development of the Cyprus Thompson Creek molybdenum deposit began near Challis, ID. The first mining claims were staked on an intrusive rock out-crop. Exploration continued for 14 years. In 1978, the decision was made to develop the deposit. In Dec. 1980, approval was received for the environmental impact statement and facilities construction and waste rock removal began. By the middle of 1983, 126 Mt (139 million st) of rock had been removed and all facilities completed. Location The Thompson Creek project is located about 58 km (36 miles) southwest of Challis in Custer County, in south central Idaho. The mine and mill are situated between 2.2 and 2.6 km (7,217 and 8,530 ft) in elevation. The project is located in an isolated area. Surrounded by mountains, it is adjacent to the Sawtooth National Recreation Area. The Salmon river is 8 km (5 miles) south of the project. The project claim block is lo-

Jan 1, 1984

By G. B. Johnston

I was very interested in Professor Park's data on subsidence over longwall panels. His paragraph labeled "Conclusion," however, does not seem appropriate for the article. Nothing in the article gives any discussion of how knowledge of subsidence characteristics can be used in mine design to minimize damage. That thought may have been a reason for undertaking this study, but not a conclusion of it. From his article, I would conclude that subsidence movements last considerably longer at great depth. And the National Coal Board's subsidence prediction model represents this area reasonably accurately, though most literature claims their model predicts far greater disturbances than actually occur in most areas of the United States. Also, I would like to know, is the method used to determine angle of draw? The criterion used can make a significant difference in the value obtained. With 30 m (100 ft) spacing and a 122-m (400-ft) depth the angle between stations can be up to 14°.

Jan 1, 1990

By Anthony G. Fonseca

About 45% to 50% of the coal mined in the United States passes through coal preparation plants. East of the Mississippi River, this number increases to about 75% to 80%. Although the cost for coal preparation is worthwhile to some, the coal industry faces the challenges of continuing downward pressure on the price of coal and the impact of new environmental regulations. Coal preparation is an effective process that achieves 75% to 80% ash reduction, 15% to 80% trace element reduction and 85% to 90% Btu recovery. It is less effective for pyrite reduction (35% to 70%) and on-line operating time (40% to 60%). It also suffers from obsolete control systems. In coal preparation, raw coal is modified to a more preferred form to enable its use. The methods used to achieve this modification must be cost-effective and appropriate to the raw coal, the scale of production and the end-user requirements.

Jan 1, 1995

By G. Olson, T. Mudder, T. Clark

An evaluation was made of an innovative chemical approach for controlling the biotic portion of sulfide oxidation of tailing and waste rock using thiocyanate. This lipophilic anion is selectively toxic toward acidophilic bacteria, including those that oxidize metal sulfides. Sulfidic materials from precious metal and base metal mining operations were treated with thiocyanate solutions and subjected to accelerated laboratory weathering at 1 to 50 kg scale in humidity cells, trays, and columns. Initial field trials were conducted at 13.6 t and 100 t scale. Thiocyanate at relatively low concentrations reduced ARD from 50% to over 99%, depending on the sample and specific ARD parameter measured. Test work also was done with phosphate as an agent to coat reactive sulfides, further reducing their oxidation by biological and chemical reactions. The combination of phosphate and thiocyanate treatment is the basis for a potentially comprehensive approach to ARD prevention and control. Additional research and pilot testing are underway.

Jan 1, 2004

By M. A. Cocquerel

INTRODUCTION Davy McKee have developed and patented a combined mixer settler (CMS) which has undergone extensive trials and has now been installed in two commercial uranium plants in South Africa. Substantial capital and operating cost savings can be realized over conventional mixer settler in uranium extraction, especially from dilute feedstocks containing approximately 200 ppm U308. Pilot plant work has also been undertaken on other metal extraction systems and the results are very encouraging in most areas of interest. CONVENTIONAL MIXER SETTLERS The conventional plant in use at many uranium recovery facilities consists typically of a mixer box in which the aqueous and organic phases are contacted and a settler in which the two phases separate. The mixer box must allow sufficient residence time for the mass transfer kinetics to be satisfied for the particular species involved. The settlers are usually rectangular and take the form of shallow tanks of large cross sectional area.

Jan 1, 1984

By Robert L. Bates

United States production of the industrial minerals, ahead of that of the metals since 1946, has shown a steady and rapid growth. By 1963, their value was more than twice that of the metals. Yet papers on the metallic ores continue to dominate the meetings of the Society of Economic Geologists and constitute nearly nine-tenths of the lead papers in Economic Geology. Most of the geological communication that does take place concerning the industrial minerals deals with high-value special-purpose minerals, which are comparable to the metallic ores in geologic complexity. The large-bulk rock products, which are growing fastest in production value, are characterized by relatively simple geology and by thousands of small producing firms, many of which do little or no geological work. The need for geological advice by this very large segment of the industry is bound to increase. In the meantime, a plea is made for more geological communication among those concerned with the industrial minerals of all varieties.

Jan 1, 1966

By Chengliang Jliang, B. K. Parek, Xuxin Shao

Of the impurities present in phosphate ore, dolomite is the most difficult to remove due to the similar chemical compositions of the impurities and also adsorption of dissolved species of dolomite onto phosphate. A new amphoteric surfactant was found to be a suitable collector for separation of dolomite from phosphate. Flotation results showed that the new amphoteric collector had a high flotation selectivity for dolomite in wide pH ranges. The flotation study of francolite and dolomite in each other's supernatant demonstrated that the dissolved ions had little effect on the selectivity of the new collector, but were detrimental to the flotation separation using sodium oleate as collector. A phosphate concentrate with 35.2% P2O5 with 90% recovery was obtained using 290 g/t of the amphoteric collector from a mixture of francolite and dolomite containing 26.2% P2O5. The rejection of MgO was 81.41%.

Jan 1, 1999

By J. K. Phiri

Copper mining is the main activity in Zambia and is confined to the large scale operations, mainly on the Copperbelt. The Copperbelt covers an area of size l00km by 50 km with a total of 10 underground and 5 open-pit mines operated by Zambia Consolidated Copper Mines (ZCCM) Limited. Most of the operations in these mines involves drilling and blasting. The loading of broken materials is by both manual and mechanical operations. Among the many risk factors associated with mining on the Copperbelt, is the occurrence of Pneumoconiosis which in the recent past has become quite prevalent and thus an important occupational health hazard for the industry. This study was carried out with the aim of establishing trends of pneumoconiosis incidence through the annual data collected by Pneumoconiosis Medical and Research Bureau of the Ministry of Health in Zambia, so that a basis could be formed for future research work. The study covers over 1,000 certified cases of Pneumoconiosis between 1960 and 1990

Jan 1, 1993

By R. J. Sweigard, T. Beckman, C. T. Justice, E. D. Thompson, T. C. Hopkins

As a means of permanent disposal, fine coal refuse is often pumped as a slurry into surface impoundments. As the available volume is filled, the embankment heights are frequently increased. The additional embankment material is often placed upon consolidated fine coal refuse. There has been concern about the long-term effect of consolidation of this material at or above the liquid limit on its shear strength. A laboratory investigation was performed using three different types of fine coal slurry taken from central Appalachian coal-preparation plants. The refuse was consolidated in 3-m (10 ft) Plexiglas columns under incremental amounts of surcharge loading. The incremental loads were designed to simulate the effect of increasing the height of a refuse embankment on top of the consolidating coal slurry. After the refuse in the columns had consolidated for several months, the columns were cut apart, and triaxial tests were performed on both the consolidated and unconsolidated material for comparison of their shear-strength parameters.

Jan 1, 1998

By J. D. Miller, J. Hupka

Important aspects of kerosene penetration into tar sand have been investigated. The natural tar sand porosity was measured and used to analyze the performance of the hot water process. Subsequently, pretreatment experiments, using 20-kg tar sand samples (Asphalt Ridge and Whiterocks, Utah) and kerosene as a diluent were carried out at the expected summer temperature (26°C) and the expected winter temperature (-14°C). The natural tar sand porosity accessible by diluent has a crucial impact on the reduction of bitumen viscosity and influences the penetration time required for successful bitumen separation from tar sand by hot water processing. Thus, the tar sand porosity is a critical variable that determines appropriate operating conditions. Experimental results indicate that diluent penetration into the Asphalt Ridge tar sand (high porosity) is almost complete after 30 min, whereas for the Whiterocks tar sand (low porosity) the penetration process is much slower, being still incomplete after 15 hours regardless of the ambient temperature.

Jan 1, 1994

Little faith can be placed in a coal resource estimate without a clear understanding of the estimate's accuracy. Different types of coal resource estimates require different levels of accuracy. Prospecting surveys typically are done with widely spaced boreholes, while a much higher level of accuracy is required for mine design. Either way, a measure of the accuracy clearly indicates the level of confidence that can be placed in the results of the estimate. Geographic information systems (GIs) are becoming a commonly used tool for resource estimation because they not only provide a database management platform but also the graphical capabilities to visualize resource characteristics. interpolation methods used commonly in these resource studies do not typically provide a quantitative answer to the question: "How accurate is the estimate?" By comparing localized measurements at multiple locations to the interpolated thickness distribution used in a resource estimate, a quantitative analysis of accuracy can be obtained. The technique is demonstrated with a case study from Central Appalachia.

Jan 1, 2000

By Tracy E. Barnes

The process of computerized reserve estimation consists of assuming a model of the spatial continuity of a deposit and then, working within the assumed model, estimating the grade and tonnage of the deposit. The basis for geostatistical analysis is a statistical definition of this continuity or the variogram. The true variogram is essentially impossible to define. So an experimental variogram is defined from the sample data and kriging proceeds assuming that this experimental variogram is a good approximation of the true variogram. Therefore the closer the experimental variogram is to the true variogram the better the estimate will be. Realizing that the variogram is nothing more than the definition of the spatial continuity of the deposit, taking the known geologic continuity of the deposit into account will give a superior variogram. The use of known geology is a widely recognized necessity for good structural analysis of a deposit, but is rarely fully incorporated into the structural analysis.

Jan 1, 1982

By A. D. Agate

In developing nations, novel mineral processing methods like bacterial leaching are gaining prominence. The principles and practices for isolation and preservation of cultures used in bacterial leaching are discussed with special reference to cultures used in leaching copper from Indian ores. In all, 145 potentially useful microorganisms such as iron- and sulfur-oxidizing bacteria were isolated from various ecosystems of the copper mining areas in the country. The major organisms isolated by enrichment culture technique belonged to T. ferrooxidans and T. thiooxidans species. In addition, thermophilic cultures like Sulfolobus sp. and thermophilic thiobacilli were also isolated. The process of copper leaching was scaled up to the 300-kg level in PVC columns. Since the preservation of efficient cultures in active state was vitally important, a new method was devised that preserved the activity of thiobacilli for a period of more than two years. The novel method of storage in sterile chalcopyrite ore at 8°C can be considered an important advance.

Jan 1, 1987

By W. Kemp Wait

Electronic ore sorting has been in use for over 15 years at many mining operations worldwide. Photometric ore sorting, which operates on the basis of measuring light reflectance levels of a rock surface, is in use at various locations on ores such as limestone, magnesite, gold, talc, spodumene, tungsten and coal. Radiometric sorters have been employed on uranium deposits in the western U.S.A. as well as at certain South African go1 d mines where preconcentrating gold is achieved using uranium association as a detector. A new ore sorter, employing two sensing parameters has been developed. Utilizing both photometric and conductivity sensing modes, this system has application to many gold ore types of North America. The first production machine has been installed at a gold mine near Beardmore, Ontario for the purpose of preconcentrating ore both from waste dumps from past production as well as within the ongoing mining operation.

Jan 1, 1987

By J. H. White

It is hypothesized that the Hotelling valuation principle (HVP) can determine the value of developed gold reserves using simple methods and easily obtainable data. This paper reports the results of an empirical test of this hypothesis. The model for the HVP is given by [V R=Cp-0(1) or V - CP-0' R(2)] where p = current spot price of gold per oz, [c] = average extraction cost of gold per oz, V = current market value of the gold in the ground (dollars) and R = gold reserves (oz). Using publicly available data from North American gold companies, we obtained data for V, R, p and c, and we ran a simple linear regression using Eq. (1) as the definition of the dependent and explanatory variables. By examining the value of the coefficients of the resulting regression equation, we can draw conclusions as to whether or not the HVP can be confidently used as an estimator of the value of developed gold reserves.

Jan 1, 1997

By Alfred Haack, Günter Girnau

INTRODUCTION From 1967 to 1976 in the Federal Republic of Germany about loo km tunnels and 125 underground stations were constructed for municipal and commuter railways solely. Additional a remarkable amount of road tunnels and sewers were built. In 1977/78 a further 27 km railway tunnels, 3.5 km road tunnels and 65 km sewers and utility lines were under construction. This shows an enormous volume of tunnel construction work. In connection with this activity various technical research and development programmes have been carried out. They deal with nearly all fields of underground works as for example soil and ground exploration, excavating and lining techniques, calculation and last but not least waterproofing problems. It is impossible within the framework of this report to touch on all the problems. Therefore, only one problem area with its different aspects will be discussed: waterproofing systems and their last developments in Germany, especially, joint sealing with special consideration of the waterproofing of concrete segmental tunnel lining (1)

Jan 1, 1979

By E. D. Dainty, B. E. Enga, D. L. McKinnon

Following considerable laboratory studies concerning particulate control systems for underground use, a program was commenced to develop practical real life implementation systems. This program covers the implementation in seven mines of particulate filter systems to 10 engine models from three engine manufacturers in 12 different vehicle types, a total of 24 vehicles. As the program ran, one mine had to drop out and a mutually agreed upon system could not be arrived at for another. Hence, the program included five Canadian mining companies. Several of the vehicles trialed at Brunswick Mining were trialed by Brunswick themselves. Nonetheless, the data is presented. This paper covers the work performed from the beginning to the end of the demonstration program. Data collected to properly select and design filter systems along with technical conclusions of the demonstration are presented. Also presented are the results of a survey that highlights the participating mines' acceptance of the technology.

Jan 1, 1991

By K. Gum, W. C. Hirt, D. A. Rice

Selective flocculation was used to produce a superclean zinc concentrate by minimizing silica contamination. Research was carried out on a flotation concentrate from the Jersey Miniere Zinc Company (JMZ) in Gordonsville, TN. The material was first dispersed with sodium silicate and then causticized tapioca starch was used to selectively flocculate the sphalerite, leaving the silica in suspension. This technique has been applied commercially to iron ore beneficiation but never to zinc processing. The feed material assayed 0.45% SiO2. The use of 0.56 kg/ t (1.13 lb/st) sodium silicate and 0.070 kg/t (0.141 lb/st) causticized tapioca starch resulted in a 98.2% zinc recovery and produced a purified zinc concentrate assaying 66.0% Zn and 0.24% silica. The target level for silica contamination in JMZ zinc concentrates is currently 0.30% Si02. This work demonstrated that selective flocculation is a potential method for cleaning flotation concentrates, particularly where low silica products are required.

Jan 1, 1995