Search Documents

By Nick J. Miles, Gareth J. Brown

The degree of fragmentation of dispersed systems of brittle materials such as pulverised rock has been described by a fractal dimension i.e. the fragmentation fractal. This fractal dimension represents a power law size-frequency distribution, where, in this case, the size is defined as the square root of the projected area. The existence of a fractal dimension for the number-size distribution, of the progeny of failure event, is direct evidence for scale invariance of the fragmentation process. Since a fractal dimension infers that failure mechanisms operate on all scales it has been suggested that the fractal dimension is a measure of the fracture resistance properties of materials during fragmentation. In order to investigate this a range of rocks of varying fracture toughness were broken under similar levels of impact velocity in the dynamic tensile failure of single particles. The fragmentation fractals determined from the resultant particle populations, of the breakage experiments, were monitored and are discussed.

Jan 1, 1995

By Eric K. Albert

Computer oriented simulation techniques can be effective in the design and analysis of complex mining systems. In fact, a number of computer software products are available for mine systems simulation. However, previous models have tended toward being either data-intensive and deterministic, or data-limited and highly stochastic. The need for a fully integrated package with a simplified user interface has never been more apparent. In this paper, the design of a surface mining simulation model documented in Albert (1986) is described. The basic features of the surface mining system and their counterparts in the simulation model are discussed. The methods and algorithms used to implement these subsystems are presented. Considerations of information management and software design are illustrated, especially as they apply to the application of the package by a mining engineer. An example is provided to demonstrate the concepts embodied in the model and to show how a surface mine is simulated from mine parameters.

Jan 1, 1989

By Michael J. Martinson, John R. Larsen, J. Warren Andrews

Measurements reported in the paper were recorded in an active Green River, Wyoming, trona mine, partly as a teaching exercise and partly to provide the mine in question with additional input data for its ventilation network program. Measurements were made: - in representative three-entry intake airways in room and pillar sub-mains; - between the lower portion of a vertical down-cast hoisting shaft and the start of an intake airway system established in a room and pillar main; - in a representative downcast section of a divided vertical shaft, and of the collar entrance loss at the top of the same compartment. Pressure differences were measured with manometers and trailing hoses, air flowrates with calibrated anemometers, and barometric pressures and wet-and dry-bulb temperatures were recorded for density determinations. Where possible, results are quoted as Atkinson friction factors, and relevant measurements are recorded in some detail to show the magnitude of fluctuations in observed pressure differences.

Jan 1, 1987

By Y. M. Jiang, D. W. Park, S. M. Lee

A vast majority of longwall operations in the US use shield-type hydraulic supports to provide ground control along the longwall face. The three-dimensional, finite-element technique combined with a progressive failure approach was utilized to simulate interaction between shields and surrounding strata and determine various loading conditions. In addition, a separate finite-element model of the shield structure was made to study responses of each longwall shield to the different loading conditions. Shield responses under various loading conditions and the shield characteristics, such as shield stiffness, the ability of resisting horizontal forces, and the effect of shield height, were studied based on the results from finite-element analyses. The results can provide the basis of effective shield design and be used for evaluation of the shield performance. It is suggested that a technique incorporating the finite-element method be developed to evaluate real-time shield performance for the purpose of effective ground control.

Jan 1, 1993

By L. Henry Smith, David C. Arthur

The Williams Mine is Canada's largest gold producer, with annual production of 14,000 Kg (450,000 ounces) from 2,300,000 tonnes of ore. Highly mechanized and automated underground mining practices are employed in order to achieve and maintain high levels of productivity and minimize costs. The Mine Ventilation System is modified to include a new Vent Raise and Variable Pitch Vane-Axial Fan. This addition allows several fan installations underground to be decommissioned. A substantial net savings in installed horse power is achieved. Heating costs associated with underground ventilation air are a significant portion of mine operating costs. Air heating costs are substantially reduced by recovering heat from upcast exhaust air, mine water and compressor cooling circuits. This waste heat is used to supplement propane fired air heating systems for underground ventilation air. An additional benefit is the availability of a heat sink for summer cooling of the compressors. System design, energy savings data and payback calculations are presented.

Jan 1, 1997

By K. Tempel

In December of 1999, Newmont Mining Corporation’s Eastern Nevada Operations commissioned its commercial biooxidation facility. The commercial biooxidation facility is a refractory gold whole ore heap process that uses bacteria to assist with the oxidation of sulfide minerals thus liberating occluded gold for further processing by cyanide for gold extraction. Before the commercial biooxidation facility was started, a decade of research went in to developing this state-of-the-art process. During final design and construction of the commercial facility a decline in gold price necessitated cost saving and project scope changes. As a result, the biooxidation process experienced many challenges. Some of the more significant challenges include poor heap permeability due to haul truck stacking, unhealthy bacteria population due to a lack of solution aeration, and insufficient biooxidation time because of limited pad space and high carbonate content in the ore. This paper discusses the many challenges encountered and addressed during the first 2-3 years of commercial biooxidation operation.

Jan 1, 2003

By R. Hogg, R. H. Weiland, P. Bunnaul

The dewatering of flocculated clay suspensions by compression in a centrifugal field was investigated. The results were analyzed with respect to the direct applicability of centrifugal dewatering (as in solid-bowl centrifuges) and indirect applications to gravity sedimentation systems. An important objective of the study was to evaluate the self-weight effect using centrifugal forces to simulate consolidation of deep sediments. Experiments were conducted in which the sediment mass and initial structure were maintained constant while the effective sediment weight was varied by centrifuging at different speeds. The relationship between the limiting sediment density and the applied consolidation stress was found to be the same for both gravity and centrifugal consolidation, indicating that small-scale laboratory tests can be used to predict consolidation in deep beds. The effects of the initial structure were also studied using controlled variations in flocculation conditions. The results imply that, for the flocculated suspensions studied, the longterm consolidation behavior is relatively insensitive to the actual extent of flocculation.

Jan 1, 1995

By Y. K. Yen, J. D. Miller, C. L. Lin

Particle size segregation is a common phenomenon in many particulate processes and has many undesirable effects. The size segregation which occurs on a belt conveyor causes a serious problem for on-line particle size measurement using image-based techniques. Whether particle size distributions measured from the top layer of the belt are representative of the total particle population is largely dependent on the degree of size segregation. Therefore, it is important to understand the nature of such size segregation in order to make appropriate corrections for on-line particle size analysis. Monte Carlo simulation has been used to provide segregation information on particles with simple geometry and the results can help to determine important factors in experiments with irregularly shaped particles. It is expected that the relationship between the particle size distribution of the top layer and that of the entire particle population on a belt conveyor can be formulated as a model based function.

Jan 1, 1997

By Talaat A. B. Lawendy, Guerry H. McClellan

Batch laboratory-scale flotation tests were conducted on some carbonate-containing sedimentary phosphate ores to obtain concentrates suitable for chemical processing. The phosphate samples tested contained both calcite and dolomite. The calcitic phosphate ore was from Israel and the dolomitic ores were from China, India, Egypt, and Pakistan. The phosphate sample from Pakistan also contained a significant amount of silica. Several flotation techniques that have been proposed for upgrading carbonate -containing phosphate ores and concentrates were tested. Two processes gave better results compared with the other processes tested: a modified IMC anionic process and a. phosphoric acid depression process. At the best flotation conditions tested, phosphate concentrates assaying 32.5%-36.5% P205, 44.0%-51.0% CaO, and 0.6%-1.0% MgO were obtained at 69%-76% overall P205 recoveries from run-of-mine (ROM) ores containing 16.0%-25.0% P205, 40.0%-52.0% CaO, and 1.0%-11.6% MgO.

Jan 1, 1993

By F. W. Petersen

In the precious metal industry, activated carbon is used extensively for the recovery of gold and silver from cyanide solutions, particularly from slimy pulps and unclarified solutions. However, carbon can easily become fouled by inert particles in the pulp, thus decreasing the activity or gold loading of the carbon. This paper attempts to quantify the distribution of fine inert particles in activated carbon. Furthermore, a possible mechanism for the intrusion of fines will be postulated. Precipitated silica and ground silica sand were used to simulate pulp conditions and their loadings on activated carbon were determined by ashing. The kinetics of intrusion of fines into the pores of carbon were relatively fast, and were dependent on the concentration in the pulp. Results indicated that particle size of the solids and zeta potential of the fines influenced the loading of inert species on carbon. Scanning electron microscopy and secondary ion mass spectrometry showed a decrease in solids concentration to the centre of the carbon particle.

Jan 1, 1995

By R. Hogg, E. Kaya, H. Cho

Investigations were performed on fine grinding of bituminous coal in a laboratory-scale pulverizer. The results indicated that the breakage behavior at relatively coarse sizes (i.e., greater than about 20 µm) is essentially "normal." However, at fine sizes (i.e., less than about 10 m), there is clear evidence of reagglomeration. A simplified population-balance model for simultaneous growth and breakage is formulated. Breakage rates and breakage distributions were assumed to follow the patterns typically observed in simple grinding systems. It is recognized, however, that solid particles and agglomerates may exhibit different breakage behaviors. Agglomeration rates are assumed to be determined by contact probability, i.e., by the relative numbers of interacting particles. Based on comparisons between model simulations and experimental data, it appears that agglomerate rebreakage rates and fragment size distributions are quite different from those for solid particles. The result is that product size passes through a minimum and then increases with time as agglomeration begins to dominate.

Jan 1, 1998

By A. A. Peshkov, N. A. Matsko, K. N. Trubetskoy

It is possible to divide the general objectives of a company into two components: maximum expected profits and viability over time. These components are designed to maximize the companies value over time. The evaluation of a project includes both a discounted cash flow (DCF) analysis and a risk analysis. The DCF analysis determines whether the project should be accepted or rejected, and the risk analysis helps to forecast possible deviations from the original estimates. However, the results of both methods do not allow for a quantitative comparison between the main objectives of the venture, and they do not resolve the issue of whether it is advisable to sacrifice immediate profits for future profits. This paper attempts to resolve this issue. The present research was carried out on mining projects with different waste-extraction schedules. Calculations were made using the US Bureau of Mines' usage-of-costs model. Russian experience in open-pit mining is reflected in this paper.

Jan 1, 1996

By V. L. Jr. Davis, F. L. Stanley, P. J. Bethell

Fwe 3 m (10 ft) diameter Microcel™ flotation columns were installed at Clinchfield Coal Company's Middle Fork preparation facility in order to reduce product ash and increase recovery and plant capacity. The Middle Fork facility is utilized for the recovery of fine coal from a feed stream that consists primarily of 1 .5 mm x 0 material. The columns replaced conventional flotation cells for the treatment of the minus 150 pm fraction while spirals are used to upgrade the plus 150 pm material in the plant feed. The addition of the column flotation circuit resulted in an increase in plant capacity in excess of 20 percent while reducing the flotation product ash content by approximately 7 percentage points. Flotation circuit combustible recovery was increased by 17 percentage points. This paper discusses circuit design, commissioning, and sparging system design. Circuit instrumentation, level control, reagent system control, performance comparisons with conventional flotation, and general operating procedures are also discussed.

Jan 1, 1995

By Robert F. Hauck

This chapter discusses a new technology for computer control in open-pit mine operations: the real time automatic dispatching of manually driven trucks to shovels. The monitoring of truck activity is accomplished by detection of local radio signals. Computer-operated directives are communicated to drivers by remote controlled digital display units inside the truck cab. The production objective is to maximize tonnage in a cost effective manner. The problem is formulated in the appendix and the solution method is briefly described. Side conditions such as maintaining delivered ore grade aims, balancing waste to ore volumes to keep within stripping ratio tolerances, and meeting production rate requirements temporarily established for certain shovels are also discussed. Experience with a developed event- to-event simulator applied to analyses of several North American mining operations using this technique is summarized. Complete systems employing this technology are now under- going installation at mine sites in Canada and the United States.

Jan 1, 1979

By Michel Dagbert

The determination of the precision of reserve estimates (tonnage, grade, quantity of metal) for an entire deposit or a large block in a deposit has received some attention in the early developments of geostatistics. A general formula to derive the estimation variance of any linear combination of a large number of sample values can be found in any geostatistical textbook like David (1977) or Journel and Huijbregts (1978). A particular case of this general formula is of course the kriging of the entire deposit. However, besides the technical difficulty of dealing with many samples the application of this formula necessitates the knowledge of the covariance between any two samples in the deposit. This is quite unrealistic in the usual case of limited stationarity where the assumption of a covariance or a variogram just function of the distance vector between two samples is only valid for samples within the same area of restricted size.

Jan 1, 1982

By P. Bevilacqua, G. Ferrara

The paper discusses the problem of accuracy in the determination of the partition curve of gravity separation processes, which is strongly affected by both the sharpness of separation of the density analysis system used and the width of the density range selected. The problem is important when the density analysis of the separation products cannot be performed using heavy liquids, but has to be performed using heavy suspensions or using other systems such magnetogravimetric separation. The imperfect separation given by these systems and the use of large density ranges lead to the determination of apparent partition curves instead of actual partition curves for the process. In the paper the relation between apparent and actual partition curves is studied under different conditions through a simulation program. For different input data, special diagrams are given which, once the apparent partition curves and the sharpness of the density cuts are known, allow calculation of the actual partition curves and the related parameters.

Jan 1, 1995

By Alex Harrison, Steve Kasper

Various countries around the world have testing and manufacturing standards in place for steel cord belting. These standards are very comprehensive in what they allow the end user to specify, however, their practical significance in terms of belt life is more difficult to quantify. Such testing standards will be briefly reviewed in this paper in relation to the implication for end user expectancy. Since there is no US standard of manufacture, the end user is left with writing their own specifications. In addition, such standards do not address the effect on belt life of manufacturing faults, such as cord plane buckles, or lateral cord movement. Some new technology used to test steel cord belting will be described as an aid to both manufacturer and end user. Specific end user related issues addressed on this paper are: Tracking and belt quality Cord plane irregularities and performance Cord size and belt life Cord fatigue and testing

Jan 1, 1993

By P. J. Suardini, S. K. Kawatra

A number of on-stream coal slurry analyzers are presently being developed and commercialized for measuring ash and solids in coal process streams, particularly around flotation circuits. The eventual goal of these efforts is to develop on-line quality control systems for flotation circuits and other fine-coal cleaning operations. As part of this on-line monitoring and control effort, it is important to gain a better understanding of the response of industrial flotation circuits to changing operating conditions. This paper summarizes the results from a detailed sampling program performed at an industrial coal flotation circuit in western Pennsylvania. The testing focused on evaluating the response of the circuit to changes in reagent dosages, operating conditions and feed compositions. The testing indicated that it is desirable to maintain high collector-to-frother ratios to enhance coarse particle flotation. The recovery of fine impurity particles was also proportional to water recovery, due to hydraulic entrainment. Key words: Industrial, Coal, Flotation, Circuit, Reagent, Response.

Jan 1, 1995

By Franc Runovc

The service hoisting plant in the mining transportation is an installation serving for the vertical transport of material and persons. An adequate mathematical model is presented for simple evaluation of the project parameters where different plant designs and the ways of transport are take into consideration. The technical and economical optimization procedure is added to the basic mathematical model of the project. This approach enables on one hand the optimization of the reconstruction of the multi-purpose hoisting plants in order to suppress possible bottle necks, while on the other hand it enables the determination of such values of the parameters of the choice and of the operation that the sum of total expenses per a transport unit' becomes the lowest. The optimization procedure is designed in such a way that all numerical data of the optimum hoisting plant are printed out together with the graphical representation of dependencies of the fundamental parameters in broader optimization region.

Jan 1, 1992

By B. J. Arnold

With the passing of the 1990 Clean Air Act Amendments, many utilities are opting to switch to lower sulfur coal to meet new SO2 emissions requirements. This lower sulfur coal may be from new suppliers or it may be from current suppliers that modify existing cleaning plants or build new plants to produce this higher quality coal. New, sophisticated coal cleaning simulators are useful tools for optimizing cod cleaning circuit operating parameters to maximize the production of clean coal that meets more stringent specifications for SO2 emissions potential. The examples in this paper were developed using the Coal Cleaning Simulator (CCS), running under ASPEN PLUS™, that was developed under a Department of Energy project cosponsored by the Electric Power Research Institute. With advanced sensitivity analysis and optimization features, CCS allows a quick, efficient, cost-effective review of coal cleaning plant performance to meet current production goals and to plan future changes in plant operating parameters or circuitry configurations.

Jan 1, 1995