Search Documents

By J. J. Davis, D. G. Osborne

The Australian coal industry is characterised by efficient fines recovery, and the climate does not dictate the use of thermal drying. With the increasing trend to underground mining and hence finer ROM coal, and market pressures for reduced product moistures, dewatering issues are assuming increasing importance in the Australian coal industry. The greatest potential gains in dewatering performance undoubtedly lie in the treatment of finely sized material. This paper examines the dewatering issues which have been recognised by the Australian coal industry, and describes current Australian research in this field.

Jan 1, 1995

Successful longwall gate entry design requires control of vertical and horizontal stresses. Vertical, or overburden, stresses are most severe in the tailgate where they are concentrated by longwall panel extraction. Horizontal stresses can also be highly destructive but they are less well understood. This paper discusses measurements of in situ horizontal stress fields in the eastern United States, experience with horizontal stress in longwall mines and methods for predicting and controlling horizontal stresses. The information presented was collected through site investigations at 45 US longwalls and an international literature review.

Jan 1, 1992

By Bhaskar B. Thapa, Michael T. McRae, Michael J. Teske, Richard M. Nolting

Packer test data and tunnel in?ow observations are used to show that the distribution of equivalent hydraulic conductivity obtained for a rock mass from borehole packer testing will be biased if the orientations of the planned tunnel and testing borehole differ. Furthermore, test results show that the distribution of equivalent hydraulic conductivity is different in various geologic sub-units at the same site. The impact on in?ow of the major uncertainties, including conductivity, head and specific yield, is illustrated to be amenable to a combined analysis using Monte Carlo simulation.

Jan 1, 2003

By George W. Poling

Designing optimal placer gold recovery plants requires a detailed knowledge of the size, shape and surface physical characteristics of the gold particles and the host alluvium in the pay gravel, sand or clay. Results of a recent pilot-scale study of the quantitative performance characteristics of riffled matted sluice systems are presented. For the appropriate non-coherent pay gravel-sand with medium-flat gold, simple sluices can recover gold at greater than 85% efficiency down to 100pm diameter. Alternatives to simple sluices are presented and discussed briefly.

Jan 1, 1987

By S. H. Advani, J. K. Lee, K. S. Chan, J. M. Avasthi

A summary of field equations governing the hygro-thermo-mechanical (coupled temperature, moisture, and stress) response of geological media is presented. The applicability of these equations, with appropriate boundary conditions, to the study of basic mechanisms associated with underground coal gasification (UCG) process is discussed. In particular, the phenomenon of stress-induced spalling resulting from intense drying near the gasified cavity and in situ effects is investigated by means of the finite element method. Some typical results from sample finite element model representations are presented for the evaluation of field experiments.

Jan 1, 1986

By W. H. B. Blackburn, D. M. S. Bhatia

Twenty-six in situ analyses of cubic galena crystals from a Mississippi Valley-type deposit were undertaken with a laser microprobe emission spectrograph to study the variation of nine trace elements from the crystal center to its periphery, both along the diagonal and vertical. The general trend is an outward increase in the concentrations of Ag, Ga, Ge and In, with As showing the opposite trend. Bi, Cd and Sn showed no discernable trends. Sb was not detected. These variation patterns may serve as a model for similar studies of other Mississippi Valley-type deposits.

Jan 1, 1987

By M. J. Hrebar

A study was conducted to evaluate the applicability of large wheel loaders (Caterpillar 994 Class) for use as primary loading equipment in open-pit iron-ore operations. Field visits were made to taconite and gold mines that used large wheel loaders. Information was gathered on loader selection rationale; operation and maintenance experience; and production, availability and costs. Brief time studies were conducted to indicate machine performance and utilization. This paper summarizes the field data that was collected, including an economic comparison of wheel loaders and cable shovels in an iron-ore application.

Jan 1, 1998

By S. Lin, Y. J. Wang

Based on systematic definitions of a generalized multiple fan ventilation system, the concepts of an augmented system, its solution curve and the operating points of the original system are introduced. The Quasi-Newton algorithm is applied in combination with the switching-parameter method to ensure a continuous search along an augmented-system solution curve and identify all the possible system operating points on it. Two example networks are analyzed to demonstrate those concepts and the application of the algorithm for identifying operating points of multiple fan ventilation systems.

Jan 1, 1994

By R. A. Metz, Isaac Vera, Hans Ruge

The El Soldado copper mineralization occurs as relatively high-grade irregular ore bodies with assay contacts and with frequent inclusions of barren rock. The sampling methods must be timely for production grade control purposes, as well as accurate and inexpensive. Sampling techniques evolved from sampling dump cars at the haulage level to sampling Scooptrams at the loading pockets. These methods were abandoned in favor of sampling production blastholes. Several sampling alternatives are discussed. These involve the selection of optimum volumes and sampling frequencies while taking into consideration geological parameters and statistical analyses of sampling data.

Jan 1, 1992

By Jorgen Elbrond

The economic environment of mining is particular and requires special methods for seeking the economic optimization of mining and guiding the construction of logical production planning systems. An interactive program system which generates sequences of mining rates and cutoff grades, using as it's core an open-ended dynamic programming algorithm, is described. The program system is built not with the aim of obtaining a single mathematical optimum, but on the concept of satisfying the mine planner by producing several alternative mine plans and testing various schedules under conditions of uncertainty.

Jan 1, 1982

By P. Bevilacqua, G. Ferrara

Hydrocyclones and other dynamic separators are normally fed with pulps consisting of water and solid particles. The solids usually consist of particles of different sizes, shapes and densities. Except in the special case of monocharacteristic particles, the particles are segregated by these differences in size, shape and density. Segregation is magnified by the high values of centrifugal acceleration in the hydrocyclones. This paper develops a segregation theory that indicates the major variables involved. Experimental data on segregation under different operating conditions for mixtures of magnetite and/or ferrosilicon and nonmagnetic minerals are reported.

Jan 1, 1997

By J. H. Kempton, D. Atkins, W. Locke

The scrutiny given to model predictions of pit-lake water quality has focused attention on the uncertainty associated with long-term predictions. Although comparison of probabilistic predictive modeling of water quality in existing pit lakes suggest that short-term predictions can bracket most parameters, un¬certainties in wall-rock reactions and the stability of groundwater composition and climate remain unquantified This overview of the uncertainties associated with longer-term predictions is presented as support for those considering policy decisions that must be made in the absence of reliable estimates of future conditions.

Jan 1, 2000

By Carol Cox Russell

More than two thousand abandoned mines within the Animas watershed in Southwestern Colorado are being prioritized for remediation by the Animas River Stakeholders Group (ARSG). Phased collection and assessment of information progressed from large scale to site specific. Prioritization was based on existing or potential environmental impact and technical feasibility of remediation as measured by dissolved Cd, Cu, and/or Zn in the discharge; indicators of habitat degradation; aquatic life in streams; cumulative impacts at the point of compliance; cost effectiveness; treatiblity/feasibility; and cultural and historic preservation.

Jan 1, 2000

By T. D. Rourke, Fred H. Kulhawy, O&apos

From mid-1976 to early 1978, a 5.64 m diameter tunnel, 2491 m long, was excavated by a modified Robbins full-face TBM under shallow cover in highly stressed sedimentary rock in Rochester, NY. In-situ stress measurements were made, and tunnel behavior was monitored with MPBXs, inclinometers, tape extensometers, and instrumented steel ribs. Detailed geologic mapping was also done. In this paper, the as-monitored tunnel behavior is described, and the TBM performance is evaluated from field records. Recommendations are also made for future tunneling in similar geologic environments.

Jan 1, 1981

By Timothy M. Dyhr, Marie Garrett

The Cannon Mine gold project has been perceived as unique for being developed in an area characterized by orchards and suburban residences. The Cannon Mine was permitted and developed successfully in this setting. However, the ability of companies to permit, develop and operate mines in mated areas is becoming more difficult as a result of opposition by residents and increasingly stringent regulation. The challenge to the mining operator in the future on otherwise economically attractive mineral deposits will be the ability to explore and develop these types of projects successfully and cost- effectively

Jan 1, 1987

By Y. Topkaya, R. E. Johnson, B. R. Palmer, R. B. Bhappu, Ronald J. Roman

The hydrodynamics of the leaching solution in leach heaps is known to be one of the important variables in the performance of the heap. The solution hydrodynamics are also important in the decommissioning of a heap where the aim is to flush out the residual dissolved metals and the remaining reagents. Chemical engineers have studied the hydrodynamics of "trickle bed" reactors for 40 years in an attempt to relate the performance of trickle bed reactors to flow conditions. Their work is reviewed with emphases on areas of similarity to heap leaching.

Jan 1, 1993

By Ryan Lemmon

Belt turnovers are commonly used in conveyors to rotate the belt so that the clean side of the belt contacts the return idlers. The belt turnover length has traditionally been sized on only the twisting stresses. However, belt turnovers are also subjected to bending stresses due to the weight of the belt. Although bending stresses have in the past been ignored, these stresses are significant and should not be neglected. This paper quantifies and presents a method for calculated twisting and bending stresses and also the belt sag.

Jan 1, 2002

By Lei Chen, Michael L. Free, Ravindra Bhide

The incorporation of particles into metal matrix materials is important to many technologically important areas. Particles that are incorporated into a metal matrix have a significant effect upon the properties of the resulting composite. Proper selection of particles and incorporation densities can lead to optimal composite properties that can be modified as needed for various applications. This paper discusses the parameters that affect the particle incorporation density in electrodeposited metal matrix composite coatings as well as a deterministic model that can be used to predict the effects of such parameters on particle incorporation density.

Jan 1, 2003

By R. L. Pozzo, I. Iwasaki

A previous investigation showed that corrosion currents estimated from polarization curves for the pyrrhotite-grinding media system under abrasion correlated well with corrosion currents estimated from marked ball wear test data by applying Faraday's law. Freshly abraded metal debris were magnetically attracted to pyrrhotite and lowered the rest potentials of the mineral particles, thereby affecting the corrosive wear. The investigation was extended to explore the interactions between a non- magnetic sulfide mineral, pyrite, and abraded metal debris and their effects on the corrosive wear mechanism. The electrochemical behavior of a three-

Jan 1, 1988

By J. A. Finch

The use of pneumatic methods for measuring interface level in flotation columns is analysed. It is shown that errors can vary over a wide range (e.g. 40 cm. in one industrial application) depending on bubble size, particle size, bubble loading, liquid hold-up and bulk slurry density. Accurate measurements (+ 5 cm) can be obtained by measuring intensive properties of the froth near the interface. Methods based on the measurement of temperature and conductivity are described and analysed. Control of the interface level using these measurements subject to various disturbances is demonstrated.

Jan 1, 1988