Search Documents

By Bruce Gellar

In March, the Prospectors and Developers Association of Canada (PDAC) held its annual conference in Toronto, Ontario. This is the third PDAC meeting the author has attended. The following are some impressions of the meeting. And the author looks forward to the joint meeting of the PDAC and the Canadian Institute of Mining, Metallurgy and Petroleum to be held March 5-10, 2000, entitled Mining Millennium 2000. One of the features of next year’s gathering is a proposed forum of world mining ministers, the first ever to be held anywhere.

Jan 1, 1999

By X. Shi

This paper presents design and implementation details of a fuzzy-behavior-based controller for an automated excavator. The robotic excavator is equipped with sensors, actuators and an embedded control system. The excavator controller uses neural-networks to interpret forces and torques gathered during the excavation process from bucket-mounted force sensors. Implementation details card experimental results using the fuzzy-behavior-based excavation controller are given for several excavation tasks. These excavation tasks demonstrate some of the complex skills that are essential for an autonomous mining-excavator controller.

Jan 1, 1997

By Gordon M. Pugh, David G. Rasmussen

INTRODUCTION This method is a variation of cut-and-fill mining where either the wall rock or the vein is too unconsolidated to permit safe mining by conventional cut-and-fill methods. Basic development consists of driving a 2.4 x 2.7-m (8 x 9-ft) haulage heading laterally in the footwall side of the vein. Crosscuts are driven over to the vein at 91-m (300-ft) intervals. Then the vein, at each inter¬section, is mined out to a distance of about 9 m (30 ft ) above the track level. After the installation of an ore chute, scrams or intermediate drifts are driven in both directions along the vein. Mining then starts imme¬diately below the level bounding the upper limit of the stope. A cut varying between 3 and 4.2 m (10 and 14 ft) in depth and mined for a distance of 45.7 m (150 ft )along the strike is taken from the orepass in each direction (Fig. 1). In this mined-out void, the floor of the cut is equipped with 203 x 203-mm (8 x 8-in.) caps hitched into the wall with steel saddle hitches installed on 1.5-m (5-ft) centers. Double wood stringers, 152.4 x 152.4 mm (6 x 6 in.), are then installed on 1.2-m (4-ft) centers longitudinally down the length of the stope. Reinforc¬ing wire mesh is also placed, overlying each mat of timber. Directly above the stringers, stulls are installed from hanging wall to footwall to hold the timber in place during the sand-filling operation. Then a cement¬sand mixture in a ratio of about 1:10 weight is poured to a depth of about 2.4 m (8 ft). The entire cycle is then repeated down to the scram drift. Another variation of timbering is illustrated in Fig. 2. There is a vein width of approximately 5.5 m (18 ft) with the same unconsolidated ground conditions. The primary difference between handling this situation and the previously described undercut-and-fill method is that standard timbered sets are installed in each excavated stoping void rather than stulls. Once again the basic method is to work down the ore block from an upper timbered drift to a lower timbered drift. Cuts are taken from a timbered raise with a chute on the stope side. Each piece of ground excavated is essentially two sets high, 5.5 m (18 ft), by two sets wide, 5.5 m (18 ft), by the length of the cut along the strike of the vein. The timbered sets are 2.4 x 2.4 x 2.4 m (8 x 8 x 8 ft). The net result is, therefore, two sets of timber on a top floor separated by doubled-up 76-mm (3-in.) lagging from

Jan 1, 1982

By Kristin Hemlein

Mining project development, permitting, environmental regulatory and compliance issues in Uzbekistan and the CIS are every bit as complex as those in the western world. The vast array of environmental permitting, monitoring and reporting regulations for mine project development and operation in the CIS are based on existing Soviet environmental regulations and policies which have remained in place after these countries gained independence from the former Soviet Union. The approach to mine project permitting in the CIS differs from the western world. Similar pre- feasibility, baseline data collection, and environmental monitoring requirements allow the project proponent to coordinate preparation and submission of documentation to support project permitting for Uzbek regulatory requirements with environmental requirements imposed by financial institutions and western environmental compliance structures. Implementation of generally accepted western environmental best management controls and monitoring into mine design, construction, and operation will not, however, ensure automatic compliance with Uzbek environmental regulations. Uzbek environmental compliance requirements that differ from western requirements include: 1) development and maintenance of an environmental database constructed specifically to address annual, biannual and quarterly statistical reporting requirements for emissions of "environmental pollutants" from the facility into air, surface water, ground water and soil; 2) preparation and submittal of specific permits for water utilization, hazardous waste storage and disposal, landfill construction and operation, and stack emissions inventories; and 3) procurement of approvals from the Uzbekistan State Committee for Nature Protection (generally analogous to the US Environmental Protection Agency). This paper outlines and summarizes the regulatory requirements for mine site permitting and the procedures for environmental monitoring and reporting during mining operation in Uzbekistan and the CIS.

Jan 1, 1997

By Louis W. Riggs

The primary concern in dealing with contractual arrangements for construction is getting the work completed satisfactorily, in the shortest time, and for the least expense for the owner--while assuring that all other parties associated with the contract make a reasonable profit for their effort. In our complex construction climate of today, achieving all of these is usually not possible. Somewhere between the beginning of design and the completion of the work, disagreements and delays arise which can destroy the best of intentions. Assuming that all parties associated with the contract are acting honorably and professionally, the disagreements generally arise through inappropriate contract types or through flawed contract documents. These flaws can be either sins of omission or commission, but we must find a way to lessen, if not completely eliminate, their impact. Disagreements and delays are directly related to the extra cost which the owner and the other involved parties must suffer. Usually the attorneys are the only ones who come out on the positive side. Inappropriate or defective contract documents can be the result of inadequate time for preparation and review, laziness in not searching out the proper terms and language, insufficient recognition of the proper assignment of risks, or just ignorance as to what is right and what is wrong for the particular project. They can also result from a client, particularly a public agency, providing rigid general conditions and format requirements with which the engineer is not allowed to tamper. Arguments

Jan 1, 1979

By Kenneth R. Dickson, I. Michael Gowring

This paper describes the underground work associated with the North Fork Stanislaus River Hydroelectric Development currently being constructed by Sierra Constructors for the Calaveras County Water District in California under a turnkey contract. Sierra Constructors is a joint venture of the Guy F. Atkinson Construction Company (sponsor) of South San Francisco, and the Harrison Western Corporation of Denver. Notable features of this project include the exceptionally high performance achieved by the 5.5m diameter Robbins tunneling machine and the 675m deep shaft pilot hole which was successfully realigned using oilfield directional drilling techniques. Other features include 3.7m and 4.3m diameter machine-excavated tunnels and various conventionally excavated tunnels constructed over a wide geographical area and diverse climatic conditions.

Jan 1, 1987

By A. E. Stewart

Slope design in an open pit mine includes determining bench height, bench face angle and berm width. Case histories are presented of two highwall slopes (160 and 220 m or 525 and 720 ft high) excavated in dipping strata in an op¬erating coal mine. These examples illustrate the influence that bench face angle can have on the stability of an entire slope. The two highwall slopes, the lower of which experienced significant instability, were excavated in approximately the same lithologic and structural environment. The main differences between the slopes were the angle at which the bench faces were excavated and the excavating methods that were used. Relevent aspects are also described of the engineering geology, slope design and excavation procedures.

Jan 1, 1998

By K. J. Sollman

With an ongoing concern for safety and health in the workplace, NYCO® requested three medical evaluations be undertaken to study possible health hazards of wollastonite. Two of the evaluations were conducted by the National Institute of Occupational Safety and Health (NIOSH). One was in 1976 (Ref. 1), and the second in 1982 (Ref. 2). The aim of the two studies was to answer the following two questions: 1. Do wollastonite workers exhibit more respiratory abnormalities than workers not exposed to wollastonite? 2. Is there a relationship between prevalence of respiratory abnormalities and accumulated expo-sure time to wollastonite?

Jan 1, 1988

By Jim Nickerson, James McCleish, Tom Abkemeier, Nicholas Willig

The purpose of this project is to convey sanitary sewage from an existing pump station to a new waste water treatment plant. This paper will discuss the design and construction aspects of the project. The scope includes construction of three main shafts ranging from 34 to 100 feet in diameter at depths of 200 to 230 feet and 21,000feet of tunnel. Shaft construction consisted of slurry wall excavations keyed into claystone and limestone at depths ranging from 114 to 130 feet, followed by rock excavation utilizing drill and blast methods. The tunnel is being excavated in the Warsaw and Salem shale and limestone formations utilizing a 12'-6" diameter Wirth hard rock TBM.

Jan 1, 2005

By John C. Franklin

INTRODUCTION Alpha-emitting radon daughter products are a recognized health hazard contributing to the development of lung cancer in persons exposed to excessive concentrations over an extended period. The primary control technique used by the mining industry is dilution with fresh air. Because the uranium is deposited in porous sandstone in most U.S. mines, the control of this hazard with dilution requires excessive volumes of air. As the mines become larger and deeper, the cost for ventilation becomes a major expenditure for the mining industry Most mines are maintaining levels of radon daughters lower than required by law but to maintain these present levels the mining companies are going to be drilling more vent holes or using other control techniques as the mine expands. These control techniques are being investigated by the U.S. Bureau of Mines to determine their effectiveness, cost, and safety for underground use. [Instrumentation] The Bureau's early research used batch sampling of both radon and radon daughters for determining the concentrations. In both cases it was determined that batch sampling did not give a complete understanding of what was happening to the concentrations. Therefore, continuous monitoring systems were developed for both. A continuous flow-through radon monitor was developed by the Bureau (Franklin, et al.., 1976) using a modified Lucas flask mounted on a photo-multiplier-tube (PMT). The air was filtered twice prior to entering the flask to remove dust, diesel smoke, moisture, and radon daughters. The signal from the PMT was then inverted, shaped, and driven to a data acquisition system (DAS) which accumulated the signals. The DAS has two comparators for setting the scan time and interval, a 24-hour clock with Julian date, a printer, and a perforated paper tape punch. Sampling time is determined by the type of experiment being conducted. Our normal sampling time is one 10-minute scan every 15 minutes, but could be set as low as one scan every minute or as long as a 16-minute scan every 167 minutes. There are two models of the DAS. One is a 10-channel system and the other a 30-channel system. On a 10channel system normally 6 channels are used for radon and radon daughters and the other four channels are used for temperature, absolute pressure, air velocity, and relative humidity as described by McVey (1977). Figure 1 shows a scan of five channels monitoring the radon concentration from intake to exhaust in a stope for a non-work day. If the radon concentration stayed this constant during work days, then continuous monitoring would not be necessary. [ ] Droullard (1977) developed a continuous alpha-beta monitor. This monitor has been modified so that it can be used with the DAS previously mentioned. Control Techniques The U.S. Bureau of Mines has conducted research in controlling airborne radon/radon daughter for 10 years. Major efforts have been conducted in sealing the rock to prevent the release of radon, bulkheading to seal nonproductive areas, backfilling with classified mill tailings, and positive pressure ventilation. Also, tests have been conducted to determine the mining cycles contribution to the radon problem. Surveys One stope with two intakes and one exhaust was continuously monitored to determine the effects of blasting, mucking, and drilling on the airborne radon concentrations (Franklin, et al., 1976). Two other detectors were located inside the stope which were close to the mining activity. In this stope no appreciable change in radon was observed during drilling holes for blasting and roofbolts. This study showed increases up to 40 percent in radon for slushing in the exhaust drift. The radon remained high and very eratic during slushing, as can

Jan 1, 1981

By D. R. Rice

Separation of valuable constituents from a complex mineral mixture was examined. Nitric acid leaching produced a solution containing copper, zinc, iron and a large proportion of silver. The residue contained antimony, lead, the remaining silver and elemental sulfur. A caustic sodium sulfide leach dissolved the antimony from the residue, producing an insoluble, high-grade silver-lead product and a filtrate for electrolytic recovery of antimony. The pH of the primary filtrate was raised, precipitating the iron and leaving a solution containing the copper, zinc and the soluble portion of the silver, which would be recovered by conventional means.

Jan 1, 1969

By J. Drelich, J. Pletka

Lost foam casting patterns are foamed polystyrene shapes glued together into the shape of the part to be cast and are coated with a refractory material consisting of a mineral mixture and binders. Prior to casting, a significant number of the patterns are damaged and inevitably land-filled. In this study, a process is developed for the recovery of foamed polystyrene from the coating and glue contaminants. The process consists of shredding, impact comminution, size classification and density separation. It is successful in separating up to 97% of the contaminants, while recovering 95% of the polystyrene.

Jan 1, 2001

By K. Burke, G. Zhan, A. Mayer

A cover with capillary barrier effects (CCBE) is being constructed on the AA Leach Pad at the Barrick Goldstrike Mine site near Carlin, Nevada. The purpose of the cover is to eliminate/minimize infiltration of meteoric waters into the leach pad. Laboratory and numerical analyses indicate that Carlin Formation siltstone (TCS), a locally available material, has the necessary hydrologic characteristics when placed on the leach pad to act as a CCBE. A pilot study has been conducted on a small-scale test cover placed on the AA Leach Pad to examine the cover performance under irrigated conditions. The preliminary test results demonstrate that the designed cover is capable of preventing meteoric water infiltration.

Jan 1, 2001

By Vi-Duong Dang

Lithium requirements in the next few decades for batteries and controlled thermonuclear fusion reactors (CTR) may exceed the availability of the current mineral and brine reserves. It is thus prudent to search for new reserves and resources to satisfy these and future lithium applications. The lithium content of the waters from the Smackover oil field. located in the Gulf Coast region of the United States, ranges from 100 to 500 mp/l and could represent a substantial new reserve. Experimental evidence described in the literature indicates that a specific chelating agent dipivaloylmethane (DPM), of the diketone type, has a specific selectivity toward lithium in the presence of other metal ions in aqueous solutions. Based in part on this unique property of dipivaloylmethane, a conceptual design of a full-size plant to extract lithium from the Smackover brine is presented in this paper. This study includes alternate flow-sheet development, design information on the major units of the process, energy requirements, and an economic analysis of a facility capable of producing 106 kg of lithium per year. The economics of three different process concepts depend primarily on the amount of water needing to be evaporated from the initial oil-field feed waters in concentrating the brine. The results, as a function of production rates, are indicated only in a general manner.

Jan 1, 1978

By S. M. S. Azghdi, K. Barani

The effect of microwave treatment on the surface roughness and wettability of chalcopyrite (CuFeS2 ) and on the chemical composition of its surface was studied. The microwave source was a conventional multimodal oven with frequency of 2.45 GHz and maximum power of 900 W. Pure chalcopyrite specimens and purified chalcopyrite concentrate were used in this study. Analysis using atomic force microscopy showed a decrease in the surface roughness of the chalcopyrite after microwave radiation. This decrease may be due to oxidation of the surface and formation of iron oxide. Moreover, the surface wettability of the chalcopyrite mineral increased with increasing duration of microwave radiation, which was in good agreement with the micro-flotation mass recovery results. The increased wettability of the surface may be attributed to the decreased surface roughness by microwave radiation. Analysis using scanning electron microscope/energy-dispersive X-ray spectroscopy indicate that after microwave radiation, the contents of sulfur and iron increased whereas that of copper decreased on the surface of the chalcopyrite, significantly changing the average atomic number of the chalcopyrite surface.

By B. Tripp

Utah produces a wide variety of industrial rock and mineral commodities, valued in 2005 at a record $758 million (21 percent of the total non-fuel mineral production of Utah). Major commodities produced in 2005 include salts (halite, potash, and magnesium salts), Portland cement, sand and gravel, carbonates (lime, limestone, and dolomite), phosphate, crushed stone, clays, lightweight aggregate (expanded shale and perlite), gypsum, silica, sulfur and sulfuric acid, and building stone. Commodities produced in smaller amounts include diatomite, pumice, gemstones, ornamental stone, fluorspar, and mineral and fossil specimens. Utah is in a period of rapid growth in industrial rock and mineral production; however, some commodities have grown faster than others. The robust western economy has stimulated production of construction-related commodities like sand and gravel, Portland cement raw materials, lime, and building stone, resulting in exploration for raw materials, development of new quarries, and expansion of existing plants

Jan 1, 2007

By P. Somasundaran, D. R. Nagaraj, Jing Wang

Polysaccharides have been widely used as depressants in mineral processing for decades. They constituent one of the most abundant family of biopolymers. However, only a small number of them have been used by industry so far because of a general lack of understanding of interactions between these polymers and minerals. In this work, adsorption tests, electrophoretic mobility measurements, microflotation and fluorescence spectroscopic tests were performed along with computer simulation to explore the mechanistic aspects of guar gum adsorption and conformation on talc as a function of relevant variables such as ionic strength, pH, solvent composition and polymer molecular weight. From microflotation tests, it was found that talc hydrophobicity decreased markedly due to the adsorption of guar gum even at very low concentrations and reached a plateau below moximum adsorption. Guar gum adsorption on talc was found to be not affected significantly by changes in solution conditions such as pH and ionic strength, ruling out electrostatic force as controlling factor for adsorption. Fluorescence spectroscopic studies showed no evidence of the formation of hydrophobic domains at talc-aqueous interface. Also urea, a hydrogen bond breaker, reduced the adsorption of guar on talc. All of the above results suggest that one of the main driving forces for guar adsorption on talc is hydrogen bonding in preference to electrostatic or hydrophobic force. This information should help toward designing reagents of optimum molecular architecture for efficient depression, dispersion or other such surface modification of particles.

Jan 1, 2005

By S. Underwood

The tracer gas method of conducting ventilation surveys is a means of determining air quantity in underground mines with knowledge of the concentration of the tracer in the atmosphere and the flow rate at which the tracer is being released. The technique is useful in inaccessible areas of underground mines and areas where traditional point measurement of velocity is not practical. Sulfur hexafluoride (SF6) is the industry standard tracer(Kennedy 1987) used in underground mines because it is safe, stable, and not naturally occurring in the mine environment. The implementation of a second tracer will increase the versatility of the tracer gas technique allowing for simultaneous releases for the study of interrelated ventilation circuits, and for conducting multiple experiments in less time. This paper will detail the selection of perfluoromethylcyclohexane (PMCH) as a novel tracer with sensitivity, physical properties, and analysis characteristics similar to SF6. Methods for the release of liquid PMCH into underground mines will be recommended, and the vulnerabilities of sample loss due to condensation of vapor PMCH will be explored. Finally, the benefits and implications of using PMCH as a second tracer will be discussed.

Jan 1, 2012

By Jon T. Langstaff

The microseismic method of detecting instability and high-stress zones in underground mines was first developed in this country by the US Bureau of Mines in the early 1940's (Obert and Duvall, 1957). Early laboratory experiments showed that when competent rocks are stressed in a testing machine, the rock noise rate (number of rock noises per unit time) increases with increasing applied stress. This increase is more pronounced as the ultimate strength of the rock is approached. Subsequent testing of rock noises in underground mines confirmed this laboratory experience and much effort has been directed in recent years to make use of this property to develop a practical method of predicting rock failure. Investigations conducted in the Coeur d'Alene district mines have pointed out a definite relationship between the stress buildup in a rock mass caused by mining activity and the emission of audible and subaudible seismic activity (microseisms). In 1968, a concentrated joint effort by USBM Denver Mining Research Center and American Smelting and Refining Co. at Asarco's Galena mine was undertaken to verify several theories regarding the generation of microseisms (Blake, 1971; Blake, Leighton, and Duvall, 1974; and Kovacs, 1973). Findings indicate that (1) rocks under stress emit detectable seismic energy; (2) the energy source can be located using a triangulation method involving travel time differences to various receiving stations; (3) the rate of release of seismic energy increases with increasing stress; and (4) this increase in noise generally precedes a major rock failure (rock burst).

Jan 1, 1979

By W. Kracht

Frothers are surfactants used in floatation to aid generation of small bubbles. Studying events at the moment of bubble creation is a challenge because of the short time frame. This presentation introduces a novel acoustic approach. The technique has the resolution capable of detecting events that occur within 1-2 ms. The transition from coalescence to non-coalescence is tracked as a function of surfactant concentration and gas rate through the capillary. Results are given for some common flotation frothers and n-alcohols (C4-C8). A stress model is used to give a qualitative explanation to the observed action of frothers on coalescence prevention. Results for salt (sodium chloride) are included for comparison).

Jan 1, 2009